Professional Documents
Culture Documents
Estanquidade Ar Proclimapresentation
Estanquidade Ar Proclimapresentation
Apoio técnico:
Luís Magalhães
(+351) 910 896 318
luis.magalhaes@eurobuild.pt
Why does heat insulation need an air seal?
Protected heat insulation is an efficient solution for keeping rooms pleasantly warm in winter
However, these air inclusions must be isolated from moving air if the insulation effects are to be maintained. The ideal insulation fulfils these requi-
rements. Also the heat insulation effects of a wool jumper are based on stationary air inclusions in the fibres: As soon as a cold wind blows, the insu-
lating effects weaken. Putting a thin windbreaker over the top reinstates the insulation effects: the insulating material is sealed off on all sides.
In summer: It is less hot indoors
1
2 1 Full rafter insulation
2 Air seal
In the case of summer heat insulation, the indoor increase in temperature is proportional to the outdoor
temperature and the time in hours the heat needs to progress from the underside of the tiles into the living
space. In summer, the target is to keep the heat outdoors for as long as possible.
The optimal solution is for the heat to start arriving in the evening hours, when it can be aired off directly. The
calculated values apply only when the structure is airtight and the heat must work inwards pore by pore.
1
2
1 Full rafter insulation
2 Air seal not tight
A poor air seal lets the heat enter the insulating material, with a considerable reduction to the effective
insulation thickness. The consequences: The actual summer heat insulation is far less than the calculated value.
Heat reaches the indoors faster, and the temperature increases more.
Condensate can cause structural damage and mould
Indoors Outdoors
Cooling
Condensate
Warm indoor air escapes to the outside where it cools. The result is condensate.
Structural damage and mould may follow.
Standard winter climate as defined under DIN 4108 Standard winter climate as defined under DIN 4108
Room temperature: +20 °C Outdoor temperature: –10 °C
Maximum humidity: 17,3 g/m3 Maximum humidity: 2,1 g/m3
Relative air humidity: 50 % Relative air humidity: 100 %
➜ Absolute humidity: 8,65g/m3 ➜ Condensate: 6,55g
The right choice of sheeting is crucial Redrying potential for greater fault tolerance
1 1
2 2
3 3
There is no back ventilation level when the whole compartment is in- This, however, is different for the intelligent, moisture variable vapour
sulated. Roof bases allowing the passage of vapour are the preferred retardant and air seal sheeting pro clima INTELLO (sd = moisture varia-
choice, e.g. pro clima SOLITEX. Here, airtight insulation solutions fea- ble from 0.25 to over 25 m). Any penetrating moisture can diffuse sa-
turing the DIN 4108 pro clima air seal sheeting INTELLO are free of fely out on the indoor side. Expressed in figures: The Fraunhofer Insti-
condensation and therefore pose no problems. The intelligent, variable tute simulation program WUFI calculates the difference between
moisture air seal pro clima INTELLO is also a reliable solution for the condensation and evaporation rates to be only 10 g/m² for the vapour
particularly demanding needs of structures with fully insulated com- retarder, but 3400 g/m² for the pro clima INTELLO solution. Structures
partments and external vapour retardant panelling (e.g. wooden clad- with the pro clima INTELLO vapour retardant sheeting (open to diffusi-
ding with bitumen felt), as shown below. on) therefore offer extremely high levels of protection against structu-
ral damage caused by leaks, and so are more tolerant to faults.
Lower energy costs, less CO2 emissions
1
3 1 Outdoors
2 External wind seal
sheeting, e.g.
pro clima SOLITEX
3 Insulation
4 4 Air seal, e.g.
pro clima INTELLO
6 5 6 5 Indoors
6 Air flow (convection)
The structure’s efficiency, reliability, and functionality depend greatly on the installation of air seal sheets, their
interbonding, and their airtight joins to all adjoining structural elements and lead-throughs.
–10 °C
And even higher heat losses are the result for wider gaps and greater air pressure diffe-
rences. This may reach an extent when homes can no longer be heated adequately under
heavy frost and high wind pressure, although the insulation’s U value has been calculated
correctly!
Protection Moisture
variable
in winter 100-fo
ld
spread
0.25
s d value 25 m
Redrying to over
in summer
System
INTELLO PLUS
Conventional vapour retardant and air seal sheeting can cause damage
PLUS
7. Primer
7. Primer
MULTIBOND
KAFLEX
ROFLEX
CERTIFICATE
Certified Passive House
Passive House Institute
Dr. Wolfgang Feist
Component
Component-ID 1106as03
valid until 31st December 64283 Darmstadt
2017
Germany
Category:
Airtightness Systems | Suface
Air Sealing
Manufacturer: permeability
pro clima
Moll bauökologische Produkte
GmbH 0.01 m³/(hm²) (±0.002)
Rheintalstr. 35-43
68723 Schwetzingen, Germany instructions for use
Product-System:
pro clima INTELLO coherent
Description:
System for surface air sealing recommended
System Components: detailing
Airtight membrane „ INTELLO
“
Self-adhesive Tape „TESCON comprehensive
VANA “
Self-adhesive Tape „CONTEGA
SOLIDO SL”
Lowest VOC rating in hazardous substance test produktpartner des dans l’air intérieur, présentant un
risque de toxicité par inhalation,
sur une échelle de classe allant de
A+ (très faibles émissions) à C
(fortes missions)
CERTIFICATE
Certified Passive House
Passive House Institute
Dr. Wolfgang Feist
Component
Component-ID 1106as03
valid until 31st December 64283 Darmstadt
2017
Germany
Category:
Airtightness Systems | Suface
Air Sealing
Manufacturer: permeability
pro clima
Moll bauökologische Produkte
GmbH 0.01 m³/(hm²) (±0.002)
Rheintalstr. 35-43
68723 Schwetzingen, Germany instructions for use
Product-System:
pro clima INTELLO coherent
Description:
System for surface air sealing recommended
System Components: detailing
Airtight membrane „ INTELLO
“
Self-adhesive Tape „TESCON comprehensive
VANA “
Self-adhesive Tape „CONTEGA
SOLIDO SL”
Forms of delivery
Art. no. GTIN Delivery form Contents Coverage PU
10106 4026639016270 Kartusche 310 ml 5 mm Bead ~ 15 m 20
8 mm Bead ~ 6 m
10107 4026639016287 Schlauchfolie 600 ml 5 mm Bead ~ 30 m 12
8 mm Bead ~ 12 m
Advantages
Glued securely - even in frosty:
Store at -20 ° C, from - 10 ° C to process
Very elastic, permanently flexible
Very high adhesion and quick drying.
No pressure lath is required on load-bearing substrates kg
Airtight bonds according to DIN 4108-7, SIA 180 and OENORM B 8110-2
Penetrates deep into the substrate * Information sur le niveau
d’émission de substances
produktpartner volatiles dans l’air intérieur,
CERTIFICATE
Certified Passive House
Passive House Institute
Dr. Wolfgang Feist
Component
Component-ID 1106as03
valid until 31st December 64283 Darmstadt
2017
Germany
Category:
Airtightness Systems | Suface
Air Sealing
Manufacturer: permeability
pro clima
Moll bauökologische Produkte
GmbH 0.01 m³/(hm²) (±0.002)
Rheintalstr. 35-43
68723 Schwetzingen, Germany instructions for use
Product-System:
pro clima INTELLO coherent
Description:
System for surface air sealing recommended
System Components: detailing
Airtight membrane „ INTELLO
“
Self-adhesive Tape „TESCON comprehensive
VANA “
Self-adhesive Tape „CONTEGA
SOLIDO SL”
Forms of delivery
Art. no. GTIN Length Width Thickness Weight PU Container
1AR00572 4026639205728 2x 10 m 11 mm 3 mm 0,74 kg 6 900
1AR00501 4026639205018 10 m 11 mm 3 mm 3,7 kg 12 Profi-VE * 150
Advantages
Glued securely - even in frosty: MULTIBOND
Store at -40 ° C, from - 15 ° C to process
Quick, clean and secure application straight from a roll
No drying time necessary, extreme adhesive strength immedia-
tely, joint is immediately airtight. No pressure lath required on
kg
subsurfaces with sufficient load-bearing capacity
Waterproof SOLID adhesive with no plasticisers, solvents,
emulgators or preservatives
Excellent values in the hazardous substance test, has been produktpartner des
* Information sur le niveau
d’émission de substances volatiles
dans l’air intérieur, présentant un
Forms of delivery
Art. no. GTIN Length Width PU Container
16038 4026639160386 30 m 8 cm 8 36
15985 4026639159854 30 m 10 cm 8 36
Advantages
Full-surface adhesive, the joint is immediately
airtight and can be subjected to loading
Extremely strong adhesion on mineral subsurfaces too thanks to kg
modified waterproof SOLID adhesive
Can be plastered over
Tape for joints on or under window frames
Easy to apply
* Information sur le niveau
CERTIFICATE
Certified Passive House
Passive House Institute
Dr. Wolfgang Feist
Component
Component-ID 1106as03
valid until 31st December 64283 Darmstadt
2017
Germany
Category:
Airtightness Systems | Suface
Air Sealing
Manufacturer: permeability
pro clima
Moll bauökologische Produkte
GmbH 0.01 m³/(hm²) (±0.002)
Rheintalstr. 35-43
68723 Schwetzingen, Germany instructions for use
Product-System:
pro clima INTELLO coherent
Description:
System for surface air sealing recommended
System Components: detailing
Airtight membrane „ INTELLO
“
Self-adhesive Tape „TESCON comprehensive
VANA “
Self-adhesive Tape „CONTEGA
SOLIDO SL”
QUATTRO
3-ply wall lining membrane with monolithic TEEE functional membrane,
suitable for open jointed and closed façades
Area of application
permanently protects the insulation from wind and rain SOLITEX FRONTA®
QUATTRO
1• For use with closed and open façades
2• open jointed façades, up to 35 mm gap width –
boarding width = min. 3 x gap width
Forms of delivery
product name Art. no. GTIN Length Width Contents Weight PU Container
SOLITEX FRONTA 12933 4026639129338 50 m 1,50 m 75 m2 13,5 kg 1 20
QUATTRO
SOLITEX FRONTA 13729 4026639137296 50 m 3,00 m 150 m2 27 kg 1 20
QUATTRO
SOLITEX FRONTA 15042 4026639150424 50 m 1,50 m 75 m² 14,5 kg 1 20
QUATTRO connect
1
2
Advantages
SOLITEX FRONTA®
Highly diffusion-permeable, but with maximum resistance to QUATTRO
driving rain
Optimum drying conditions for wall structures
non-porous TEEE functional membrane actively transports
moisture outwards
Black fleece and black print prevent the membrane showing
through open jointed façades
Maximum ageing resistance and thermal stability
thanks to the TEEE membrane
6 months of outdoor exposure
SOLITEX MENTO ®
Family
3 or 4 layer roof underlays
Area of application
Three or four layer roof underlays permeable roof lining SOLITEX MENTO® -Family
and sarking Membrane which is suitable for
1• laying on boarding, MDF and fibreboard roof lining panels
Product Art. no. GTIN Length Width Contents Product Art. no. GTIN Length Width Contents
KAFLEX mono for 1 cable – Ø 6-12 mm 10724 4026639016195 14,5 cm 14,5 cm 5 ROFLEX 20 for pipes – Ø 15-30 mm 10730 4026639016393 14,5 cm 14,5 cm 5
KAFLEX mono for 1 cable – Ø 6-12 mm 10725 4026639016188 14,5 cm 14,5 cm 30 ROFLEX 20 for pipes – Ø 15-30 mm 10731 4026639016416 14,5 cm 14,5 cm 30
KAFLEX duo for 2 cable – Ø 6-12 mm 10726 4026639016171 14,5 cm 14,5 cm 5
KAFLEX duo for 2 cable – Ø 6-12 mm 10727 4026639016072 14,5 cm 14,5 cm 30
ROFLEX 20 multi
Multi conduit grommet for up to 9 conduits
KAFLEX multi Product Art. no. GTIN Length Width Contents
Multiple cable grommet for up to 16 cables, Ø 6-12 mm
ROFLEX 20 multi for up to 9 conduits 12936 4026639129369 20 cm 20 cm 2
Product Art. no. GTIN Length Width Contents
KAFLEX multi for up to 16 cables – Ø 6-12 mm
KAFLEX multi for up to 16 cables – Ø 6-12 mm
10728
10729
4026639016096 14 cm
4026639016102 14 cm
14 cm
14 cm
2
20 ROFLEX 30 / 50 / 100 /150 / 200 / 250 / 300
Sealing grommets for pipes
KAFLEX post
Product Art. no. GTIN Length Width Contents
ROFLEX 30 for pipes Ø 30-50 mm 14166 4026639141668 14 cm 14 cm 2
Sealing patch for already installed cables ROFLEX 30 for pipes Ø 30-50 mm 14167 4026639141675 14 cm 14 cm 20
Product Art. no. GTIN Length Width Contents ROFLEX 50 for pipes Ø 50-90 mm 10732 4026639016430 14 cm 14 cm 2
KAFLEX post for 1 cable - Ø 6-12 mm 12942 4026639129420 14 cm 14 cm 5 ROFLEX 50 for pipes Ø 50-90 mm 10733 4026639016447 14 cm 14 cm 20
KAFLEX post for 1 cable - Ø 6-12 mm 12943 4026639129437 14 cm 14 cm 20 ROFLEX 100 for pipes Ø 100-120 mm 10734 4026639016454 20 cm 20 cm 2
ROFLEX 100 for pipes Ø 100-120 mm 10735 4026639016461 20 cm 20 cm 20
ROFLEX 150 for pipes Ø 120-170 mm 10736 4026639016478 25 cm 25 cm 2
ROFLEX 150 for pipes Ø 120-170 mm 10737 4026639016485 25 cm 25 cm 20
ROFLEX 200 for pipes Ø 170-220 mm 10738 4026639016492 30 cm 30 cm 2
ROFLEX 200 for pipes Ø 170-220 mm 10740 4026639016508 30 cm 30 cm 20
ROFLEX 250 for pipes Ø 220-270 mm 12832 4026639128324 45 cm 45 cm 2
ROFLEX 300 for pipes Ø 270-320 mm 12842 4026639128423 50 cm 50 cm 2
Advantages
Sicher auch in heißem Umfeld: KAFLEX / ROFLEX
Temperaturstabil bis 150°C
Pipes and cables can be still be pulled or pushed
High-quality EPDM, extremely flexible and elastic, w
no excess bushing
CERTIFICATE
Certified Passive House
Passive House Institute
Dr. Wolfgang Feist
Component
Component-ID 1168ap03
valid until 31st December 64283 Darmstadt
2018
Germany
Manufacturer:
Product(s):
Description:
Airtightness Systems | Penetration
pro clima
MOLL bauökologische Produkte
Rheintalstr. 35-43
68723 Schwetzingen, Germany
coherent
recommended
from cables and pipes detailing
Single products:
„KAFLEX mono, multi und comprehensive
post“
„ROFLEX 20, 50, 100 und
200”
This certificate was awarded
Forms of delivery
Productname Delivery form Art. no. GTIN Contents Adhesive tape width Coverage PU Container
TESCON PRIMER RP Tin 11427 4026639114273 0,75 l 60 mm ~ 60 m 6 84
75 mm ~ 45 m
150 mm ~ 22 m
TESCON PRIMER RP Tin 11430 4026639114303 2,5 l 60 mm ~ 185 m 4 40
75 mm ~ 150 m
150 mm ~ 75 m
TESCON PRIMER RP Dispenser 11449 4026639114495 1l 60 mm ~ 75 m 6 72
75 mm ~ 60 m
150 mm ~ 30 m
TESCON SPRIMER Tin 1AR01114 4026639211149 400 ml 60 mm ~ 20 m 12 84
75 mm ~ 17 m
150 mm ~ 9m
TESCON SPRIMER Tin 1AR01050 4026639210500 750 ml 60 mm ~ 38 m 4 40
75 mm ~ 31 m
150 mm ~ 17 m
Advantages
No drying required - adhesive can be applied straight
to the damp primer on absorbent substrates
Deep penetration of the primer, excellent hardening
TESCON SPRIMER: Easy to apply - spray on directly from the can,
no contamination of the primer in its container
Application even on damp substrate
Can also be used in the event of frost
Can be used with any pro clima adhesive tape
* Information sur le niveau
d’émission de substances volatiles
TESCON PRIMER RP: Solvent free produktpartner des dans l’air intérieur, présentant un
risque de toxicité par inhalation,
sur une échelle de classe allant de
A+ (très faibles émissions) à C
(fortes missions)
Information and ordering
service
Information and ordering service
Pro clima’s information service is the quickest way to access all information about systems, products, events and promotional campaigns.
You can also request information material and samples here in an uncomplicated manner.
Information and ordering service
Tel.: +49 (0) 62 02 - 27 82.0
eMail: info@proclima.de
www.proclima.com
Engineering Hotline
Immediate answers relating to building physics, construction, systems or products. Our engineers in Timber Construction can help you quickly and
simply in an expert manner and help you find solutions on cost-effective, reliable constructions that will lead to healthy living environments.
Engineering Hotline
Tel.: +49 (0) 62 02 - 27 82.45
eMail: technik@proclima.de
Contact person
Jens-Lüder Herms
Tel.: +49 (0) 62 02 - 27 82.41
eMail: jens.lueder.herms@proclima.de