For forming the internal thread by mechanical displacement of material
(fig. 1), screws with a sheet metal screw thread as specified in DIN 7970 or wood screw thread asspecified in DIN 7998 are suitable
ABC Spax screw
Fa. Altenloh, Brinck & Co., D-58256 Ennepetal PT screw Fa. E. Jäger GmbH & Co., D-57319 Bad Berleburg Plastite screw Vertrieb]. H. Krumb, D-61440 Oberursel Thread designs of different thread forming screws
These special designs differ from sheet
metal and wood screws in having a smaller receiving hole diameter and consequently a greater thread depth. The thread angle of these screws is 30 to 45 compared with the 60 for the sheet metal screws. PlasTORX® Studs for Plastic Assemblies Can be molded directly into plastic, replacing metal stamping and fastener assemblies. Engineered to provide high resistance to rotation and pull-out. Plastite® 48 Thread-Forming Screws for Thermoplastics These thread forming screws combine a unique tri-lobular body with a 48° thread profile to maximize performance and reliability in softer thermoplastics. Thread-cutting screws For less ductile plastics such as the reinforced partially crystalline thermoplastics, thread-forming screws are not so suitable. Thread-cutting screws on the other hand can be used to advantage. The most suitable are thread-cuttingscrews as specified in DIN 7513 and sheet metal screws with cutting notches or a cutting edge in the first turns of the thread Joint with metric screws Screwed joint with thread-forming The strength of a screwed joint screws Is directly dependent on the thread bite t, Nominal screw diameter d and screw engagement length L HOSTAFORM. PP HOSTACOM. POM Types of failure in screwed joints with moulded bosses
D > 2.5 d D< 2.5 d
Recommended L = 2.5d Relaxation modulus Er of the plastic
Screwed joint with thread-cutting screws
For this type of joint, basically the same factors apply as for joints with thread-forming screws Screwed joint with threaded inserts and threaded bolts Joint with self-tapping screws Curve a is for Hostaform and curve b for PT screws, ABC Spaxscrews and Plastite the Hostacom grades. screws 6.1 Driving torque MA The driving torque MA must be great enough for the connecting parts to be in full and secure contact and for a sufficiently high pre-stressing force to be created. This requirement is met if the driving torque MA is selected as follows: Hostaform (basic grades and modified grades) MA = 0.25 to 0.3 M (4) Hostacom MA = 0.35 to 0.4 M (5) M = stripping torque (figs. 17 and 18).
6.2 Axialforce Fperm.
When the screwed joint is under a constant continuous stress, experience has shown that about 25 to 30% of the pull-out force shown in figs. 17 and 18 can be permitted, Fpern, = 0.25 to 0.3 F DIN 7972 ISO 1482
Rosca chapa avellanado
• DIN 7972 / ISO 1482 ROSCA CHAPA AVELLANADO 4.2 x 9.5
1000 9.11 € 21.44 € DIN 7972 / ISO 1482 ROSCA CHAPA AVELLANADO 4.2 x 13.0 1000 9.84 € 22.67 € DIN 7972 / ISO 1482 ROSCA CHAPA AVELLANADO 4.2 x 16.0 1000 10.26 € 25.37 € DIN 7972 / ISO 1482 ROSCA CHAPA AVELLANADO 4.2 x 19.0 1000 10.74 € 27.77 € DIN 7972 / ISO 1482 ROSCA CHAPA AVELLANADO 4.2 x 22.0 1000 11.79 € 30.50 € DIN 7972 / ISO 1482 ROSCA CHAPA AVELLANADO 4.2 x 25.0 1000 12.38 € 33.23