Professional Documents
Culture Documents
инструкция по установке сигнализации Е60, Е61
инструкция по установке сигнализации Е60, Е61
Installation Instructions.
Alarm system retrofit
BMW 5 Series Saloon (E 60)
Installation time
The installation time is approx. 5.0–5.5 hours. This may vary depending on the condition of the car and the
equipment in it.
In general the car must be upgraded to the latest I stage status by flashing before starting the conversion work.
Differing programming times may be necessary depending on the production age of the vehicle and on work
previously performed on the vehicle.
The installation time specified does not include the time spent on programming / coding.
The calculation of the total costs for the programming time must be factored into the calculation of retrofitting costs
(no invoicing via warranty).
Important information
These installation instructions are primarily designed for use within the BMW dealership organisation and by
authorised BMW service companies.
In any event, the target group for these installation instructions is specialist personnel trained on BMW cars with
the appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work
instructions, in a rational order, using the prescribed tools (special tools) and observing current safety regulations.
If you experience installation or function problems, limit troubleshooting to approx. 0.5 hours for
mechanical or 1.0 hour for electrical work.
In order to reduce costs and avoid any additional expense, send a query immediately to the Technical Parts Support
via the Aftersales Assistance Portal (ASAP).
Specify the following information:
- Chassis number,
- Part number of the retrofit kit,
- A precise description of the problem,
- Work steps already carried out.
Do not archive the hard copy of these installation instructions since daily updates are provided via ASAP!
Pictograms
Denotes instructions that draw your attention to dangers.
!
Ordering instructions
The interior roof light cover G is not supplied with the retrofit kit and must be ordered separately for individual colour
variants (for part number and instructions see EPC).
Section Page
1. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Preparatory work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
9. Alarm system system circuit diagram cars built before 09/05 only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10. Alarm system system circuit diagram cars built after 09/05 only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
A B C
D E F G H I J K L
060 0931 Z
Legend
A Wiring harness A
B Wiring harness B
C Electric chrome mirror
D Ultrasound module
E Emergency power siren
F Engine compartment lid contact switch
G Ceiling light cover (not supplied with the retrofit kit)
H Cable tie L = 50 mm (2x)
I Cable tie L = 200 mm (20x)
J Nut M6
K Miniature connector (4x)
L Cable eyelet M6 (only for cars built after 03/05)
ISTA No.
Conduct a brief test ---
Disconnect the negative pole of the battery 12 00 ...
A2 A3 A4 A5 A6 A7 A8
A
A9
A1 A10
A11
060 0911 Z
Item Designation Signal Cable colour / Connection location in the car Abbreviation /
cross-section slot
A Wiring harness A --- --- --- ---
A1 Socket casing --- SW Electric chrome mirror X18246
A2 Cable open CAN HIGH SW Only cars built before 03/07 or with SA 5AD/SA 610
0.50 mm2 To the rain/light sensor
Only cars built after 03/07 without SA 5AD/ X15011
SA 610
To the light module
X15001
PIN14
A3 Cable open CAN LOW GE Only cars built before 03/07 or with SA 5AD/SA 610
0.50 mm2 To the rain/light sensor
Only cars built after 03/07 without SA 5AD/SA 610 X15012
To the light module
X15002
PIN 32
A4 Socket casing --- SW Ultrasound module X1582
A5 Cable eyelet M6 Terminal 31 BR Right comb connector on the C-pillar X13790
0.50 mm²
A6 Socket contact Terminal 30 RT/SW Cars built before 09/05 only
0.50 mm2 Rear fuse holder X11012
SW 32-pin plug PIN 6
Cars built after 09/05 only
Rear fuse holder X11015
SW 16-pin plug PIN 12
A7 Socket contact Terminal 15 GN/GE Cars built before 09/05 only
0.35 mm2 Rear fuse holder X11012
SW 32-pin plug PIN 15
Cars built after 09/05 only
Rear fuse holder X11012
SW 41-pin plug PIN 28
A8 Cable open RFS BL/GE Right rear light X318
0.35 mm2 PIN 3
A9 Socket contact Terminal 31 BR Emergency power siren X372
0.50 mm² PIN 1
A10 Socket contact DWAH SW/BL Emergency power siren X372
0.50 mm² PIN 2
A11 Socket contact Terminal 30 RT/SW Emergency power siren X372
0.50 mm² PIN 3
B1 B B2 B3
060 0912 Z
Item Designation Signal Cable colour / Connection location in the car Abbreviation /
cross-section slot
B Wiring harness B --- --- --- ---
B1 SW 3-pin socket plug --- --- Engine compartment lid contact switch X161
B2 Comb connector contact Terminal 31 BR Cars built before 03/05 only X1816
0.50 mm2 To the comb connector behind the glove compartment
Cars built after 03/05 only
With cable eyelet L to the earth support point on the X13782
bottom right A-pillar
B3 Socket contact MHK VI/GN To the CAS control unit X10318
0.50 mm2 SW 41-pin plug PIN 38
7
F B 1 2 C A D 3 E 4 5
E65
8
060 1419 Z
Legend
A Wiring harness A
B Wiring harness B
C Electric chrome mirror
D Ultrasound module
E Emergency power siren
F Engine compartment lid contact switch
B 060 0041 Z
B1
060 0042 Z
X1816
B2
060 0043 Z
X13782
L
060 00934 Z
All cars
M
X10318 B3
060 0044 Z
A1
060 0045 Z
060 0047 Z
A2
A3
0601420 Z
K
A2/A3
060 1421 Z
All cars
Route wiring harness A to the right-hand B-pillar.
060 0048 Z
060 0049 Z
A5
X13790
060 0050 Z
A
A6
060 1423 Z
All cars
Draw the dimensions as follows on the tail panel (1):
1 - 35 mm from the outside of the cable duct (4)
- 55 mm from the bottom edge (3)
35mm Drill a drill hole (2) with an arbor-type cutter to
2 40 mm diameter.
Deburr the hole and coat the bare surfaces with
55mm
preservative.
3 4 060 0017 Z
A9-A11
060 0053 Z
E 1
060 0057 Z
E
060 0058 Z
D
000 0055 Z
D G A4
060 0056 Z
X18246/A1
060 0054 Z
6 15 X11012 3 10 8 9 1 X18246 38
X10318
RFS
30 DWA
15
D
30 IR
15
31
A6 A7
GN/GE 0,35
GR/SW/GE 0,35
RT/SW 0,5
BL/GE 0,35
VI/GN 0,50
BR 0,35
RT/SW 0,5
A8
RT/SW 0,5
X318
X16009
X15011
X15012
A2 A3
SW 0,35
GE 0,35
SW/BL 0,5
BR 0,5
BR 0,5
A11 A10 A9
CAN HIGH
CAN LOW
30 DWA
30
31
31
D
S
3 2 1 X372 8 7 1 5 3 2
X1582 1 X161
S19
H1 A121
2
X161
BR 0,50
A5
X13790 X1816/X13782
060 0937 Z
38
12 28 3 10 8 9 1
X18246 X10318
RFS
X11015
30 DWA
15
D
30 IR
15
31
X11012
A6 A7
GN/GE 0,35
GR/SW/GE 0,35
RT/SW 0,5
BL/GE 0,35
VI/GN 0,50
BR 0,35
RT/SW 0,5
A8
RT/SW 0,5
X318
X16009
X15011 / X12
X15012 / X12
A2 A3
SW 0,35
GE 0,35
SW/BL 0,5
BR 0,5
BR 0,5
A11 A10 A9
CAN HIGH
CAN LOW
30 DWA
30
31
31
D
S
3 2 1 X372 8 7 1 5 3 2
X1582 1 X161
S19
H1 A121
2
X161
BR 0,50
A5
X13790 X1816/X13782
060 1422 Z
Legend
X12 CAN High/Low (cars built after 03/07 without SA 5AD/SA 610 only)
X161 SW 3-pin plug
X318 SW 6-pin plug
X372 SW 3-pin plug
X1582 SW 8-pin plug
X1816 Comb connector (cars built before 09/05 only)
X10318 SW 41-pin plug
X11012 SW 32-pin plug (cars built before 09/05)
X11012 SW 41-pin plug (cars built after 09/05)
X11015 SW 16-pin plug (cars built after 09/05)
X13782 Earth support point (cars built after 03/05 only)
X13790 Comb connector
X15011 CAN high (cars built before 03/07 or with SA 5AD/SA 610 only)
X15012 CAN low (cars built before 03/07 or with SA 5AD/SA 610 only)
X16009 Terminal 30 connector
X18246 SW 10-pin plug
Cable colours
BL Blue
BR Brown
GE Yellow
GN Green
GR Grey
RT Red
SW Black
VI Violet
WS White