Professional Documents
Culture Documents
TPS User Manual (Manual - TPS3h-1512-V2)
TPS User Manual (Manual - TPS3h-1512-V2)
For Lift
Operation Manual
(TPS3h-1512-V2)
INTRODUCTION
The ARD is a newest generation of emergency rescue device for elevator system to guarantee the return
of cabinet to the nearest floor or bottom floor and open the door safely in the event of AC mains power
failure, also in the case of power problem with lift itself. The smart CPU-based ARD can be installed
with any type of control panel of elevator systems, it functions with sealed acid batteries and free
maintenance. Easy installation and safe landing the cabinet for 100% security to the lift’s operation.
FEATURES
․ Smart CPU to detect the elevator power condition at real time and operate the safe landing for any
emergency happened.
․ V3F technology to fit the variable voltage and variable frequency for reliable power supply to the
elevator
․ LCD display
CAUTION
Thank you for using our product. For the sake of maintaining the normal operation of this ARD
device, please read the user manual completely before installation.
Please carefully check the model and parameters on the nameplate of this product with relevant
parts of elevator. If there is any non-identical information, please contact with the authorized
engineering service center where you bought the device immediately, to consult the solution before
any installation or operation.
Don’t touch the high voltage parts built in the device during testing or setting the parameters or
checking the unit.
If this device has not been used over than six months, please charge the batteries before operation.
The device may be stayed at the system integrator site for some time, thus, please check it with
the supplier if you have uncertain information about this matter.
<1>
Battery charging m ethod :
Connect input pow er in 3 phase / 380VAC or 3 phase / 220VAC to charge the batteries
autom atically.
If there is any failure happened, please contact with the qualified technical service center, all
repairs should be performed by qualified service personnel.
OUTLOOK
Power Switch
LCD Display
Terminals for
wiring connection
<2>
SPECIFICATON
<3>
SETTINGS
<4>
WIRING CONNECTIONS
Single
Phase :
P.S.: 1. Shall be confirmed elevator for the main transformer positioned in phase U and phase V.
2. When city power off need connection with phase sequence protection relay, otherwise
elevator will could not start.
external switch (open door switch)
S1 When set S1 in close circuit, ARD will shutdown the elevator and restart the elevator
automatically when AC mains come back.
Three
Phase :
(Type 1)
(Type 2)
<5>
Explanation of LCD Display
Pushing the button for 2~3 seconds, the ARD will be turned on (or
Start ARD when Black out
turned off).
Battery Full
Open on level
<6>
简介
ARD 是最新一代电梯系统救援装置,当停电时,可确保抵达最近的楼层或最底部的楼层,并安全地打开
电梯门,也适用于电梯本身发生电力问题的情况。智能型微处理器设计基础的 ARD 可安装于任何控制面
板的电梯系统。搭配密封式免维护铅酸电池。安装容易,使电梯 100%安全降落。
特色
․ 智能型微处理器设计,在任何紧急情况发生时,立即电梯电力检测及安全降落操作
․ V3F 技术能适应可变电压及可变频率,可靠的供应电力给电梯
․ 复合控制电路设计
․ 复合式机械设计以节省空间
․ 易于安装, 操作安全
․ 液晶显示
․ 超载管理
注意事项
请仔细核对产品卷标上所列型号、参数及相关部分,如不一致,请勿安装及操作使用,并立即联系
购买地的授权技术服务中心咨询解决办法。
机壳内有高压,若开盖测试设定,请勿触及高压部分。
如果设备超过 6 个月未使用,请于使用前对电池充电。因设备也许在系统整合商存放了一段时间,
如果你对于这个问题有疑问,请向供货商确认。
电池充电方法:
接上输入电力,即可自动电池充电
如有发生任何的故障,请联系合格的技术服务中心,所有的维修动作需由合格的技术人员执行。
<7>
外观
电源开关
液晶显示屏
接线端子台
规格
<8>
设定
备注 : VR1 = 输出电压调整
VR2 = 超载保护调整
备注 : VR1 = 充电电压调整
VR2 = 充电电流调整
<9>
端子台接线指示
单相 :
P.S.: 1. 需确认电梯内的主变压器是在 U 相及 V 相
2. COM, NO 需短接三相相序保护器, 否则电梯无法启动
外部控制开关 (开门开关)
S1
当 S1 在关闭状态, ARD 会关闭电梯,并且当市电回复时自动重新启动电梯。
三相 :
(样式 1)
(样式 2)
外部控制开关 (开门开关)
S1
当 S1 在关闭状态, ARD 会关闭电梯,并且当市电回复时自动重新启动电梯。
< 10 >
液晶显示说明
液晶显示内容 备注
巽阳应急电源
電池已充滿
超過負載 负载超过额定负载
已到平層樓開門
< 11 >
凭本卡保修, 请注意保留
保 修 卡
产品型号
序号
售出日期
售出单位
(请加盖公章)
保修条列
本公司产品享有自出售之日起 12 个月的保修服务,如超过保修期限,本
公司将视故障情况酌情收取费用
保修卡务必请售机单位盖章及注明出售日期,以确保您的权益。不然将以
产品出厂日起算保修期限。
在保修期限内,发生以下事项者, 本公司有权拒绝服务或酌情收取材料
及服务费。
(1) 用户使用不当造成的产品故障或损坏
(2) 机器曾自行拆修,改装,更换零件者
(3) 产品卷标损毁者
(4) 意外事件自然灾害导致的故障或损伤
延长保修期限
在原本标准保修期限之外,另外提供延长保修选购,延长产品使用期限。
选购延长保修,请于保修期限内选购。
电池不在延长保固范围
本公司保留对所有内容的修改权和解释权
巽阳电子有限公司
客服电话 : 86-769-83181421
Keep the card for guarantee to keep it repair.
Warranty Card
Model
S/N
Date
Sales location
Warranty clause:
The company's products reserve from the date of the sale of the 12-month warranty
services, such as exceeding the warranty period, the company will in accordance
by defective conditions to charge the repaired fees.
The warranty card will have the Seal by our factory and indicate the date of sale, to
ensure your right and interests.
Otherwise, the factory will be count from the date of sale for the warranty period.
Within the warranty period, it happens by the following matters, the company has
the right to refuse the services or receive material and service charges as
appropriate.
(1) Improper use to cause the failure or damage.
(2) The machine has its own overhaul, modification and parts replacement.
(3) Damaged by the product label.
(4) Failure or damage accidents caused by natural disasters.
The Company reserves the right for all content modification and interpretation