Professional Documents
Culture Documents
Rieker Incorporated. Complete Line of Inclinometers, Accelerometers and Tilt Indicating Instruments
Rieker Incorporated. Complete Line of Inclinometers, Accelerometers and Tilt Indicating Instruments
China Office Tel: 010 - 5129 4688/8708 3686 Fax: 010 - 8256 1891 Http://rieker.asensors.net
B Series
General Specifications Brochure
Page 2 of 2
TYPE B1 B2 B3
2 2 2
Measuring Range ±3g (Approx. ±30m/s ) ±10g (Approx. ±100m/s ) ±50g (Approx. ±500m/s )
ATTENTION! The supply voltage must not exceed 6 Volt and the polarity must not be reversed.
Compact Accelerometer:
for Dynamic Measurement of
Acceleration or Vibration in
Frequency Ranges 1Hz to 1.5kHz.
Description Features
BDK sensors are dynamic accelerometers that are Compact housing, less than 1” diameter
capacitive spring-mass based, with incorporated Light weight
sensor electronics. Resonance peaks are minimised Very high overload resistance
by means of a special gas-dynamic damping in the
Insensitive to interference by magnetic
primary transformer. With very low power
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
MECHANICAL CHARACTERISTICS
Type 1 Stainless Steel, M6 Mounting Stud
Housing
Type 2 Nickel Plated Brass
Type 1 Ø 0.87” (Ø 22mm) X 0.39” (10mm) h
Dimensions
Type 2 Ø 0.80” (Ø 20mm) X 0.30” (7,5mm) h
Type 1 Approx. 0.60 ounces (17 grams)
Weight
Type 2 Approx. 0.25 ounces (7 grams)
FORM NUMBER: SK0039_11/07 UPDATED: --
©2002-2007 Rieker® Inc. All Rights Reserved.
Electrical Standard 3 highly flexible, color-coded wires Ø 0.04” (Ø 1.0mm) x 7.0” (18cm)
Connection Optional Type 1 Housing: Shielded cable Ø 0.083” (Ø 2.1mm) x 1.65’ (0.5m)
Operating Temperature -40°F to +185°F (-40° to +85°C )
Storage temperature -49°F to +194°F (-45° to +90°C )
Current Consumption Ub=5Volt BD: Approx. 250uA (optional 30uA), BDK: Approx. 2mA
Description Features
The H4 Series of inclinometers provide single axis Single Axis Angle Measurement
inclination sensing in a rugged environmentally
protected metal housing. The sensing package 3 Ranges: ±30°, ±45º, ±70°
incorporates a liquid capacitive sensing element and 2 Levels of Temperature Compensation
integrated temperature compensation over the
industrial operating range of –40° to +85°C. Analog Voltage 0-5V Output
Serial Digital RS232 Output
These sensors are available with a choice of two
output configurations, analog voltage or digital Vibration and shock resistant
serial outputs. These outputs are linear with respect Environmentally sealed to IP66
to the input angle directly. Depending on the
required accuracy, two levels of temperature Rugged die-cast Zinc housing
compensation are available. EMC protected
The content presented is provided for informational purposes only and subject to change.
Technical Specifications
INPUT PARAMETERS
MEASURING RANGES ±30°, ±45º, ±70°
MEASUREMENT AXIS Single
8 to 30 VDC Non-Regulated
POWER SUPPLY
optional 5VDC Regulated
OUTPUT PARAMETERS
1 < 0.5% Full Range for ±30º model
NON-LINEARITY
< 0.2% Full Range for ±45º, ±70º models
NULL REPEATABILITY < 0.05°
TRANSVERSE SENSITIVITY < 1.0% at 30º Tilt
SENSOR ELEMENT RESPONSE TIME < 0.3 seconds (<300mSec)
BANDWIDTH 3 Hz
OPTIONAL TEMPERATURE
< ±1.0° (over full operating temperature range)
COMPENSATION OUTPUT DRIFT
TEMPERATURE RANGE
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
MECHANICAL CHARACTERISTICS
HOUSING Die Cast Zinc
MOUNTING HOLES Two #6-32
MOUNTING PLANE Vertical Surface
OUTLINE DIMENSIONS Ø1.95” x 1.1” (Ø49.5 x 28mm) See Drawing
ELECTRICAL CONNECTION 1ft. Teflon Cable with 3 pigtail leads
WEIGHT 8 ounces (227 grams)
Notes: 1. Non-linearity generated by best fit straight line using least squares regression. Output is linear with respect to the
input angle directly.
OPTION
CODE
HOUSING
MACHINED ZINC METAL (Default) 4
ALTERNATIVE HOUSING N/A
OUTPUT
ANALOG A
DIGITAL SERIAL (RS232) S
TEMPERATURE COMPENSATION
LEVEL 1 1
LEVEL 2 2
ANGLE RANGES
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
INPUT POWER
8 TO 30VDC (Default) BLANK
5VDC V
MODEL NUMBER
STANDARD (or stock) CONFIGURATION (Default) BLANK
CUSTOM SPECIAL: “-X” = LETTER ASSIGNED AT TIME OF ORDER “-X”
As shown above the part number H4A1-30 represents a standard (or stock) configuration single
axis unit with a ±30º measuring range, Analog output, Level 1 Temperature Compensation, 8 to
30VDC supply power.
The content presented is provided for informational purposes only and subject to change.
Description Features
The N Series inclination sensors are liquid capacitive Small housing, less than 1” dia.
gravity based sensors with integrated sensor electronics. Measuring Ranges: ±10, ±30, ±70º
These sensors provide Analog DC output; the measuring
Linear output characteristics
principle assures a linear angle output equal to the
measuring range of the sensor. Minimal zero offset drift
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
MECHANICAL CHARACTERISTICS
HOUSING 30% Glass Filled PBT Plastic
FORM NUMBER: SK0008_01/02 UPDATED: 01/07
N Model Specifications N2 N3 N4
Measuring range ±10° ±30° ±70°
Resolution < 0.002° < 0.005° 0.01°
< 0.5% Full Range for ±10° model
Max. Non-linearity
< 0.2% Full Range for ±30°, ±70° models
Transverse Sensitivity <1% at 30° tilt
Response Tme < 0.3 Sec. (<300mSec)
Power Supply Ub 5 Volt regulated
Min ... Max. Supply Ubz 3 ... 6 Volt
Current consumption Ub=5Volt Approx. 1mA
Protection Degree IP65
VALUES FOR ANALOG DC OUTPUT MODEL AT UBN=5VOLT
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Accurate Electronic
Inclinometers with Non-
amplified, Non-conditioned
Analog Output in Ranges of
±10, ±30 and ±80º
Description Features
The NG Series inclination sensors are liquid capacitive Linear output characteristics
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
gravity based sensors with integrated sensor electronics. Minimal zero offset drift
These sensors provide Analog DC output; the measuring Hysteresis free output signal
principle assures a linear angle output equal to the
High measurement accuracy
measuring range of the sensor.
Very low relative linearity errors
The sensor electronics require only minimal power - Integrated sensor electronics
power consumption is very low (approx. 1mA) - and are
in conjunction with the capacitive primary transformer, Long-term stability
which is characterized by high accuracy, a high signal- Low power consumption
to-noise ratio and long-term stability. Analog mV output signal
Hermetically sealed housing to
Applications IP65
These inclinometers are suitable for applications Zero offset mechanically
requiring high measurement accuracy with low linearity adjustable through 360 within
deviations and high long-term stability for measurement mounting ring
of relatively large inclination angles. No interference by ambient
The content presented is provided for informational purposes only and subject to change.
electromagnetic fields
Typical areas of application include construction, Shockproof to 10,000g: no moving
mining, automotive/vehicle tilt, surveying equipment, mechanical parts
aircraft, transportation and conveyor systems.
Sensor electrically isolated from
point of measurement using high
quality PBT plastic housing - no
ground connections
MECHANICAL CHARACTERISTICS
FORM NUMBER: SK0029_07/02 UPDATED: 01/07
Description Features
Temperature compensated
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Applications parts
Hermetically sealed housing to
The NGi Series with its current loop output is well suited
IP67
for industrial use where high accuracy and long-term
stability are required in a noisy environment where high Sensor galvanically isolated from
temperature changes occur and non-stable supply voltages housing
are present. Sensor zero mechanically
adjusted with mounting ring
For additional functionality the SB1i and SB2i
Inclinometer Sensor Packages have both zero and gain Current loop limitation
FORM NUMBER: SK0009_07/02 UPDATED: 01/07
adjustments. For dual axis applications refer to the SB2i. Hysteresis free measuring signal
The SB2i is also available with CSA Certification for
©2002-2007 Rieker® Inc. All Rights Reserved.
Intrinsic Safety.
Typically used in building and bridge construction, mining,
radar alignment systems, pitch and roll,
agricultural/construction equipment, and process
machinery.
MECHANICAL CHARACTERISTICS
HOUSING 30% Glass Filled PBT Plastic
ENVIRONMENTAL PROTECTION IP65
MOUNTING Flat Vertical Surface with Supplied Mounting Ring
Ø 1.92” (Ø 48.8mm) X 0.85” (21.6mm) h
OUTLINE DIMENSIONS
With Mounting Ring: Ø 2.64” (Ø 67mm) X .85” (21.6mm) h
ELECTRICAL CONNECTION Ø 0.182” (Ø 4.6mm) Cable x 1.65’ (0.5m) (2-wire pigtails leads)
WEIGHT Approx. 3.88 ounces (110 grams) (not including mounting ring)
OPERATING TEMPERATURE -40°F to +185°F (-40° to +85°C )
STORAGE TEMPERATURE -49°F to +194°F (-45° to +90°C )
CABLE WIRING TABLE:
BROWN +VDC input or output
WHITE +VDC input or output
The content presented is provided for informational purposes only and subject to change.
Description Features
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
The NGU Series of inclinometers - NG2U (±10º), NG3U Temperature Compensated 0…5V
(±30º), and NG4U (±80º) - are liquid capacitive gravity output
based sensors with integrated sensor and excitation
electronics. The thermal drift of the primary sensor is Non regulated +8…+30VDC supply
further compensated by an electronic equalization of the input
temperature. Integrated sensor electronics
An integrated highly stable voltage regulator makes it with 5VDC excitation
possible to supply the inclinometer from any unregulated Linear output characteristics
supply or battery as low as +8V and up to +30VDC. The
measuring principle assures a linear angle output with High measurement accuracy
0…5VDC calibrated to equal the measuring range of the
Very low relative linearity errors
sensor. The measuring time constant can be ordered with
longer rise times upon request. High long-term stability
accuracy, long-term stability, and high voltage outputs are electromagnetic fields
desired in environments that experience large
Vibration and shock insensitive
temperature changes and where non-stable supply
due to non mechanical internal
voltages are present.
parts
For additional functionality the SB1U and SB2G
Inclinometer Sensor Packages have both zero and gain Hermetically sealed housing to
adjustments. For dual axis applications refer to the SB2G. IP65
Typically used in building and bridge construction, mining, Sensor galvanically isolated from
FORM NUMBER: SK0002_01/03 UPDATED: 01/07
MECHANICAL CHARACTERISTICS
HOUSING 30% Glass Filled PBT Plastic
ENVIRONMENTAL PROTECTION IP65
MOUNTING Flat Vertical Surface with Supplied Mounting Ring
Ø 1.92” (Ø 48.8mm) X 0.85” (21.6mm) h
OUTLINE DIMENSIONS
With Mounting Ring: Ø 2.64” (Ø 67mm) X .85” (21.6mm) h
ELECTRICAL CONNECTION Ø 0.182” (Ø 4.6mm) Shielded Cable x 1.65’ (0.5m) pigtail leads
WEIGHT Approx. 3.88 ounces (110 grams) (not including mounting ring)
OPERATING TEMPERATURE -40°F to +185°F (-40° to +85°C )
STORAGE TEMPERATURE -49°F to +194°F (-45° to +90°C )
Description Features
The NG360 is a liquid capacitive based inclinometer used RS485 Output – Bus and Multi-
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
for measuring the tilt angle of any object with respect to Sensor Capable
gravity within a 0 to 360° range. This inclinometer
features an integrated 16-bit single chip microprocessor, Integrated 16 Bit
which provides for linearity and temperature Microprocessor
compensation. The basic sensor consists of four separate EEPROM Storage of Sensor
sensing elements whose outputs are combined to provide a Parameters
highly accurate linear output over a complete 360° tilt
range. An inclusive EEPROM stores the calibration data and Windows Based Software
dynamic control functions. The embedded software Supporting Bi-Directional
virtually eliminates total errors by compensating Calibration
temperature drifts and sets the sensor dynamics for Full 360° Angle Sensing
specific customer applications. It provides a very accurate
360° angle output with a RS485 interface. When used 0.01° Resolution
along with the SC485B (RS232/RS485) converter the user Linearity and Temperature
has the possibility of connecting up to 78 units on the Compensated
same communication line.
Insensitive to electromagnetic
The content presented is provided for informational purposes only and subject to change.
processing on a PC.
Typical areas of application include construction, mining,
vehicles, aircraft, ships, surveying equipment, and
transportation and conveyor systems.
TECHNICAL SPECIFICATIONS
MEASURING RANGE 360º
RESOLUTION 0.01º
MAX. NON-LINEARITY ±0.25°
TRANSVERSE SENSITIVITY <1% at 45° cross angle
OUTPUT RESPONSE TME < 0.3 Sec. (<300mSec)
SUPPLY VOLTAGE “ON” DELAY TIME < 50mSec
POWER SUPPLY 9V ... 15V
CURRENT CONSUMPTION approx. 40mA
MECHANICAL CHARACTERISTICS
HOUSING 30% Glass Filled PBT Plastic
ENVIRONMENTAL PROTECTION IP65
MOUNTING Flat Vertical Surface with Supplied Mounting Ring
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Single Sensor
The content presented is provided for informational purposes only and subject to change.
running Windows 95/98 or Windows XP. Although the NG360 will operate from any half-duplex RS485 port, we recommend
using the SEIKA interface converter SC485B. NG360 programs should be copied to the hard drive before running them!
1. Load the enclosed software NG360Setup.exe and GetAngle.exe onto a PC.
NG360Setup.exe: This program can be used to change several parameters of the NG360. These parameters can be read,
modified and then saved permanently in the NG360 EEPROM. This does not affect any calibration values.
Run the executable file, NG360Setup.exe to setup system parameters. Parameters that can be reconfigured are data
filtering with regards to filter type (Bessel, Period, Butterworth, or Tschebychev), filter order (either no filter, first, or
2. second order), and filter frequency (0.1Hz, 0.5Hz, and 1Hz). The sensor address can also be set and changed if
more than one sensor is connected. Refer to Figure 3 for connecting multiple sensors. PC COM port assignment is
also accomplished with this program.
Once a sensor address is selected, the corresponding sensor can be probed for its current parameter settings. Click
on “read variables”. This will read the current filter settings and sensor address and display them in the appropriate
fields. The variables can be modified by selecting on the drop down menus and then permanently written to the
4.
EEPROM memory by clicking on “write variables”. The variable V064 “delay for serial port” determines the time delay
between the individual data bytes transmitted by the sensor. This value can be increased for slower PC interfaces for
safer data communication. Default value is 500.
GetAngle.exe: This program displays the angle of one or more NG360, which are connected through a RS232/RS485-
Converter (i.e. p/n SC485B) to the PC. The serial port COM, the sensor address and the display speed (averaging of several
measurements) can be adjusted. Additionaly, measurements can be saved to a logfile in regular time-intervals, for further
processing i.e. with MS Excel.
The content presented is provided for informational purposes only and subject to change.
Set the correct Com port and address. Note address 177 (hB1) #00 can only be used when one sensor is connected.
6. Clicking on Start will show the sensor output real time. If you want to change the filter parameters go back to the setup
program.
NG360Scan.exe: Use this program to identify every NG360 sensor connected to a serial PC COM port through a
RS232/RS485-Converter. The program scans the whole range of possible NG360 addresses and displays the angle values
send by each connected sensor.
Program NG360Scan.exe is
also supplied on the disk. This
program will determine which
sensors are active on the bus
7.
and then allow continuous
reading of multiple sensors. The
following screen will appear
when executed.
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Select the Com port and click on Scan. The program transmits an inquiry to all 78 possible NG360 addresses and waits
8. for a response. If a sensor answers, the received measured angle is displayed over that sensors address. Click on Start
reading to obtain continuous angle measurements from the active sensors. Press Stop reading when finished.
HARDWARE RESET
The NG360 sensor is RESET automatically at power on by a defined sequence of operations. The timing for the power on
sequence is important for the correct function of the internal microcomputer. The starting edge of the supply voltage should be
The content presented is provided for informational purposes only and subject to change.
Description Features
The NB3 is a static accelerometer (utilized as an Small compact housing, less than 1”
inclinometer) with a high degree of accuracy for diameter
measuring small tilt angles of any object with 0.3 or 0.01 Second Response Time
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
MECHANICAL CHARACTERISTICS
Housing Nickel Plated Brass
Mounting M3 Mounting Stud, M4 optional
Mounting Plane Vertical Surface
Outline Dimensions Ø 0.945” (Ø 24mm) X .434” (11mm) h
FORM NUMBER: SK0014_08/02 Updated: 02/07
NB MODEL SPECIFICATIONS
Measuring range ±10°
Resolution < 0.001°
< 0.2% Full Range for ±10° model
Max. Non-linearity
< 0.5% Expanded Range for ±20°
Transverse Sensitivity Negligible
NB3 < 0.3 Sec., Frequency 0-7Hz
Response Tme
NB3S < 0.01 Sec., Frequency 0-60Hz
Power Supply Ub 5 Volt regulated
Min ... Max. Supply Ubz 3 ... 6 Volt
Current Consumption Ub=5Volt Approx. 1mA
Protection Degree IP65
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
NV4a
Signal Amplifier/Conditioner
Page 1 of 2
RIEKER
ELECTRONICS INC The NV4a is used for filtering
output signals from electronic
sensor units with ±4 Volt DC output.
Features
Works directly on a non-regulated Zero and span adjustment by means
power supply from +8 to 30VDC of high quality potentiometers
Internal zero setting of sensor offset Electronic parts hermetically enclosed
Reverse polarity protection for both Programmable low-pass filter optional
input voltage and sensor High-pass filter also available
Output is short-circuit protected Custom made connectors also possible
Internal voltage regulation to sensor
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
Description
The NV4a signal amplifier is used to excite, filter, normalize, and convert the different output signals
of Seika sensors to a ±4VDC output. This symmetrical output signal allows for a problem-free signal
transfer to measurement equipment such as oscilloscopes, AD-cards in PC’s, or to other OEM
equipment. (For 0 to 5VDC output, we recommend the NV8a and for 4 to 20mA output, the NV6a).
Even with large fluctuations at the unit’s power supply, the NV4a will act very stable for both
offsetting the sensor’s zero point and supplying a stable ±4 Volt DC output, which is linear to the
sensor’s working range.
Applications
The NV4a is strongly recommended for use in combination with a sensor anywhere the demand for
high voltage output and/or special filtering of the sensor’s signal is needed. This signal amplifier is also
useful when a non-stabilized 8 to 30VDC supply is required.
The content presented is provided for informational purposes only and subject to change.
Technical Data
Dimensions 1.97” (50mm)l x 0.984”(25mm)w x 0.402” (10.22)d
Supply Voltage +8...+30Volt (reverse polarity protected to -70Volt)
Current Consumption Approx.2mA (without sensor)
Operating Temperature 0...70°C
Sensor Supply +5.00 Volt
Sensor Supply – Temperature Drift 20ppm /°C
Max. Output Voltage ±4 Volt
Active Measuring Range ±3.5 Volt (Equal to Sensor Range)
FORM NUMBER: SK0011_10/02 Updated: 02/04
©2002-2004 Rieker® Inc. All Rights Reserved.
NV4a
Signal Amplifier/Conditioner
Page 2 of 2
RIEKER
ELECTRONICS INC
NV4a Dimensions (in mm) and Wiring Connections
10.22
50
5.5
25
5.4
6.185
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
27.94
2.54
2.54
2.54 1.12
2.54
2.54
Caution! Do not short circuit the operating voltage (8...30V) with the outputs.
The negative operating voltage of the symmetrical VDC output is generated from the positive one.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
NV6a
Signal Amplifier/Conditioner
Page 1 of 2
RIEKER
ELECTRONICS INC The NV6a is used for filtering output
signals from electronic sensor units
with 4 to 20mA and 2-wire current
loop output.
Features
2-wire connection – current loop Zero and span adjustment by means
powered of high quality potentiometers
No extra power required Electronic parts hermetically enclosed
Internal zero setting of sensor offset Programmable low-pass filter with
Reverse polarity protection for both optional settings
input voltage and sensor High-pass filter also available
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
Description
The NV6a signal amplifier is used to excite, filter, normalize, and convert the different output signals
of Seika sensors to a 4 to 20mA output. This type of output signal allows for a problem-free signal
transfer to measurement equipment such as oscilloscopes, AD-cards in PC’s, or to other OEM
equipment. Connected sensors do not require a separate supply voltage, as the NV6a provides a
highly stable SV sensor supply voltage with short circuit current limitation. (For 0 to 5VDC output,
we recommend the NV8a and for ±4 VDC output, the NV4a).
Even with large fluctuations at the unit’s power supply, the NV6a will act very stable for both
offsetting the sensor’s zero point and supplying a stable 4 to 20mA current output, which is linear to
the sensor’s working range.
Applications
The content presented is provided for informational purposes only and subject to change.
The NV6a is strongly recommended for use in combination with a Seika sensor anywhere the demand
for a 4 to 20mA, 2 wire current loop output and/or special filtering of the sensor’s signal is needed.
The use of this signal amplifier is also useful when a non-stabilized 8 to 30VDC supply can be an
advantage for the system, or when signal transmission is required over long distances.
Technical Data
Dimensions 1.97” (50mm) l x 0.984”(25mm) w x 0.402” (10.22) d
Supply Voltage +8…+30Volt (reverse polarity protected to -70Volt)
Current Consumption Approx. 2mA (without sensor)
Operating Temperature -40…+85°C
FORM NUMBER: SK0010_10/02 Updated: 02/04
NV6a
Signal Amplifier/Conditioner
Page 2 of 2
RIEKER
ELECTRONICS INC
Power Supply Noise 30µVpp
Signal to Noise Ratio > 65dB (with standard sensor)
Frequency Range 0…10Hz; 0…200Hz; 0…1kHz (custom ranges available)
Pin connector: 0.10” (2.54mm)w x 0.224” (5.7mm)l Optional
Electrical Connections
0.025” (0.63mm) gold plated soldering pads
CAUTION! Sensor-GND and NV6a-GND (both have same potential) must be isolated from the current-loop! In case of
multiple axes (e.g. inside SW3) all sensor grounds/housings must be isolated from each other. This should be
considered when ordering: The sensor unit must be internally isolated when combined with an NV6a! This does not
apply to VOLTAGE OUTPUTS amplifiers (NV4a, NV8a).
Since the supply voltages for the NV6a/sensor combination are obtained from the current loop and together require
maximum 3mA, an input voltage of 8V minimum must be supplied to the NV6a. This is required in order to guarantee
correct operation when
PO Box 127 the highest
• 777 loop current
Henderson (approx.
Blvd • Park Square24mA)
North is used.
Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
NV8a
Signal Amplifier/Conditioner
Page 1 of 2
Features
Small size for OEM applications Zero and span adjustment by means
Works directly on a non-regulated of high quality potentiometers
power supply from +8…30VDC Electronic parts hermetically enclosed
Internal zero setting of sensor offset Programmable 3rd order low-pass filter
Reverse polarity protection for both with optional settings
input voltage and sensor High-pass filter also available
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Description
The NV8a signal amplifier is used to excite, filter, normalize, and convert the different output signals
of Seika sensors to a 0 to 5VDC output. The asymmetrical output signal allows for a problem-free signal
transfer to measurement equipment such as oscilloscopes, AD-cards in PC’s, or to other OEM
equipment. (For 4 to 20mA current output, we recommend the NV6a and for ±4 VDC output, the NV4a).
Even with large fluctuations at the unit’s power supply, the NV8a will act very stable for both
offsetting the sensor’s zero point and supplying a stable 0 to 5VDC output, which is linear to the
sensor’s working range.
Applications
The NV8a is strongly recommended for use in combination with a Seika sensor anywhere the demand
for high voltage output and/or special filtering of the sensor’s signal is needed. The use of this signal
The content presented is provided for informational purposes only and subject to change.
amplifier is also useful when a non-stabilized 8 to 30VDC supply can be an advantage for the system.
Technical Data
Dimensions 1.97” (50mm) l x 0.984”(25mm) w x 0.402” (10.22) d
Supply Voltage +8…+30 Volt (reverse polarity protected to -70Volt)
Current Consumption Approx. 10mA (without sensor)
Operating Temperature -40…+85°C
Sensor Supply +5.0 Volt
Sensor Supply Temperature Drift 20ppm /°C
Max. Output Voltage +0.05V…+4.95V
FORM NUMBER: SK0009_10/02 Updated: 02/04
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
NV8a
Signal Amplifier/Conditioner
Page 2 of 2
RIEKER
ELECTRONICS INC
Frequency Range
Electrical connections
0...10Hz; 0...200Hz; 0...2kHz (custom ranges available)
Pin connector: 0.10” (2.54mm)w x 0.224” (5.7mm)l Optional
0.025” (0.63mm) gold plated soldering pads
CAUTION! Do not short circuit the operating voltage (8 to 30V) with the outputs.
No problems with GND – all on the same potential, also in case of multiple axis systems! The sensor’s
operating voltage of +5V/maximum 10mA may also be used as a voltage reference for connected
electronics (e.g. OPV or ADC) because of its very high accuracy.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
RDI Series
General Information Brochure
Page 1 of 4
Features Applications
Single or Dual Axis Measurement Slope Warning System
Custom Input Ranges from ±4° to ±100° Roll Over Early Warning
LCD Displays Angle in Degrees, Percent Platform Leveling
Grade, or Inch per Foot Rise Pitch and Roll Monitoring
0.1° or 0.01° Display Resolution Vehicle Tilt Monitoring
Relative Zero Function Antenna Positioning
Minimum/Maximum Display Boom Angle Indicating
Analog 0 to 5VDC Output Safe Curve Speed Indicating (Ball Banking)
RS232 Serial Output Sound System Remote Speaker Alignment
Up to 4 Open Collector Switch Outputs Mining/Boring Equipment Leveling
Optional Adjustable Trip Angle Settings Bang-Bang Type Valve Controller
High Current-Sink Capability
Lamp/Solenoid/Relay Driver
The content presented is provided for informational purposes only and subject to change.
Description
The RDI provides single or dual axis inclination sensing in a rugged environmentally protected housing.
This is a semi-custom unit where all subassemblies are stock but specific functions are customized. A
modular design allows the customer to select the measurement range, output type, and temperature
compensation that best suits the individual application. Standard input ranges ±10°, ±30° and ±70°
are available for both single and dual axis models – these can be scaled to specific ranges (ie: ±45º)
per axis. Special single axis ranges up to ±100° are available. Non-symmetrical (or scalable) ranges
FORM NUMBER: RD0001_06/03 UPDATED: 02/07
(ie: -10° to +90°) are available for applications that only tilt in one direction.
The RDI can be supplied with multiple output configurations: Digital LCD Display, Analog Voltage 0.25
to 4.25V output, Digital Serial RS232 output, and up to 4 Open Collector Switch Outputs providing
©2002-2007 Rieker® All Rights Reserved.
maximum functionality.
The LCD display can be configured to display degrees, percent grade, or inch per foot rise with either
0.1 or 0.01 degree resolution. The display models come standard with 3 built in LED’s (1 green, 1
yellow, and 1 red). These can be set activate at predefined angles within the specified measurement
range - providing the operator a bright visual warning signal. Examples of LED programming: For
leveling applications - the LED function is set so the green LED turns RDI Sample Models
on when level then switches to yellow or red when out of level; For
indication of safe and unsafe conditions (such as preventing vehicle
rollover) - the green light would indicate the vehicle is within the safe
operating zone, the yellow light would indicate a warning zone, and
the red light would indicate the vehicle is on a slope that exceeds the
recommended safe operating zone - giving the operator a bright visual
immediate danger signal to return to more even ground.
The LCD display model also provides a Relative Zero and a RDR Remote Sensor Package
Minimum/Maximum Angle function. The Relative Zero (REL) allows the
operator to temporarily zero the digital readout to obtain relative
slope changes. The operator will always know when the device is in
the REL mode by the (*) symbol that is displayed after the angle. The
Minimum/Maximum Angle (MIN/MAX) function provides the smallest
and largest angle the device has sensed since the last reset.
There are up to four (4) Open Collector Switch Outputs that, if
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
selected, can be factory set to switch at a predetermined angle RDS7-BB Ball Bank Indicator
anywhere within the selected measurement range. The switching
function can be configured for either Normally Open for out of range
indication or Normally Closed for in range indication. The outputs can
be used to drive an external buzzer, horn, lamp, solenoid, or relay
allowing for audible and/or visual warnings and equipment shut down
control. Each switch output can be delayed from 0 to 16 seconds to
eliminate false triggering. Available in both display and non-display
models, with a display model the outputs are tied directly to the LED’s
on the front panel and are configured to indicate when switching RAD Remote Angle Display
occurs for the open collector switch outputs.
The analog voltage (0-5V) output is available as either temperature
compensated or non-temperature compensated depending on the
required accuracy for the specific application (operating temperature
is used to determine this option). A 12 bit digital to analog converter
is used to perform the conversion.
The content presented is provided for informational purposes only and subject to change.
INPUT PARAMETERS
Standard: ±10°, ±30°, ±70°
Measuring Angle Ranges Scalable: Symmetrical ±4° min to ±70° max (single axis up to ±100°)
Scalable: Non-Symmetrical anywhere within full scale of range (ie: -10º to +90º)
Measurement Axes Single or Dual
Axis Mounting Any Direction
Power Supply 8 to 30 VDC Non-Regulated, (5VDC Regulated optional)
Display Version (Without LED): 15mA typical
Current Consumption Display Version (One LED): 35mA typical
Max All Options: 100mA max.
OUTPUT PARAMETERS
1
Non-Linearity < 0.5% FR
Null Repeatability < 0.05°
Transverse Sensitivity <1.0% at 30° Tilt
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Response Time < 0.3 seconds (300mSec), (slower response times available)
Stop Bits 1
OPEN COLLECTOR SWITCH OUTPUT
©2002-2007 Rieker® All Rights Reserved.
MECHANICAL CHARACTERISTICS
Housing Die Cast Aluminum – Painted Black
Environmental Rating Nema 4
Mounting Holes Two M4 x 0.7 or Two #8-32 (Mounting Feet Optional)
Outline Dimensions 4.54” x 3.54” x 2.27” (115 x 90 x 56mm) See Drawing
Electrical Connection 15 pin Din (Refer to Wiring); alternative connectors available
Weight 16 ounces (not including cable)
Display Models Non-Display Models, Storage
Operating Temperature
-20°C to +70°C -40°C to +85°C
Notes: 1. Non-linearity generated by best fit straight line using least squares regression. Output is linear with respect to the
input angle directly. 2. Sensor Temperature Drifts apply to Non-Temperature Compensated versions. 3. LED trip angles can
only be set within the measuring range of the device and must match the open collector switch outputs if they are selected.
Features Applications
Single or Dual Axis Measurement Slope Warning System
Custom Input Ranges from ±4° to ±100° Roll Over Early Warning
LCD Displays Angle in Degrees, Percent Platform Leveling
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
Description
The RDR Remote Inclinometer Package is an extension of the RDI series. The package is supplied as a
calibrated set featuring an environmentally sealed inclinometer box (single or dual axis), an LCD
The content presented is provided for informational purposes only and subject to change.
The LCD display can be configured to display degrees, percent grade, or inch per foot rise with either
©2002-2007 Rieker® Inc. All Rights Reserved.
0.1 or 0.01 degree resolution. The display models come standard with 3 built in LED’s (1 green, 1
yellow, and 1 red). These can be set activate at predefined angles within the specified measurement
range - providing the operator a bright visual warning signal.
Examples of LED programming: For leveling applications - the LED function is set so the green LED
turns on when level then switches to yellow or red when out of level; For indication of safe and
unsafe conditions (such as preventing vehicle rollover) - the green light would indicate the vehicle is
within the safe operating zone, the yellow light would indicate a warning zone, and the red light
would indicate the vehicle is on a slope that exceeds the recommended safe operating zone - giving
the operator a bright visual immediate danger signal to return to more even ground.
The LCD display model also provides a Relative Zero and a Minimum/Maximum Angle function. The
Relative Zero (REL) allows the operator to temporarily zero the digital readout to obtain relative
slope changes. The operator will always know when the device is in the REL mode by the (*) symbol
that is displayed after the angle. The Minimum/Maximum Angle (MIN/MAX) function provides the
smallest and largest angle the device has sensed since the last reset.
The RDI can be supplied with multiple output configurations: Digital LCD Display, Analog Voltage 0.25
to 4.25V output, Digital Serial RS232 output, and up to 4 Open Collector Switch Outputs providing
maximum functionality.
Optional Temperature Compensation can be added to provide increased accuracy. For applications
that require remote angle measurement (the sensor unit is mounted separately from the Display box)
we offer Remote Inclinometer packages and Remote Angle Displays with multiple sensor options.
The analog voltage (0-5V) output is available as either temperature compensated or non-temperature
compensated depending on the required accuracy for the specific application (operating temperature
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
is used to determine this option). A 12 bit digital to analog converter is used to perform the
conversion.
The digital RS232 output is presented in decimal format in degrees, percent grade, or inch per foot
rise. The output is formatted one reading per line for single axis units and two readings per line for
dual axis units. The first reading for a dual axis unit represents channel 1 (typically side to side/roll)
and the second reading represents channel 2 (typically front to back/pitch). The dual RDI can also be
configured with both channels reading along the same axis for double redundancy.
There are up to four (4) Open Collector Switch Outputs that, if selected, can be factory set to switch
at a predetermined angle anywhere within the selected measurement range. The switching function
can be configured for either Normally Open for out of range indication or Normally Closed for in range
indication. The outputs can be used to drive an external buzzer, horn, lamp, solenoid, or relay
allowing for audible and/or visual warnings and equipment shut down control. Each switch output can
be delayed from 0 to 16 seconds to eliminate false triggering. Available in both display and non-
display models, with a display model the outputs are tied directly to the LED’s on the front panel and
are configured to indicate when switching occurs for the open collector switch outputs.
The content presented is provided for informational purposes only and subject to change.
The RDI is powered by a 8-30VDC non-regulated power supply (default power), with optional 9V
battery, 110VAC or 240VAC wall adapters, or cigarette lighter adaptor. Various connectors and cable
options are available based on the application and operating environment.
Technical Data
INPUT PARAMETERS
Standard: ±10°, ±30°, ±70°
Measuring Angle Ranges Scalable: Symmetrical ±4° min to ±70° max (single axis up to ±100°)
FORM NUMBER RD0011_09/03 UPDATED: 06/07
Scalable: Non-Symmetrical anywhere within full scale of range (ie: -10º to +90º)
©2002-2007 Rieker® Inc. All Rights Reserved.
OUTPUT PARAMETERS
1
Non-Linearity < 0.5% FR
Null Repeatability < 0.05°
Transverse Sensitivity <1.0% at 30° Tilt
Response Time < 0.3 seconds (300mSec), (slower response times available)
3. LED trip angles can only be set within the measuring range of the device and must match the open collector switch outputs if they are chosen.
©2002-2007 Rieker® Inc. All Rights Reserved.
FIGURE 1: RDI Display Box, Dimensions (Inches [mm]) and Mounting Position
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
FIGURE 2: RDI Remote Inclinometer Box, Dimensions (Inches [mm]) and Mounting Position
The content presented is provided for informational purposes only and subject to change.
FIGURE 3: RDI Display Box with Mounting Feet, Dimensions (Inches [mm]) and Mounting Position
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
FIGURE 4: Remote Box (optional mounting feet) Dimensions (Inches [mm]) & Mounting Position
The content presented is provided for informational purposes only and subject to change.
SB1i (4-20mA)
Single Axis Inclinometer Sensor Package
® Page 1 of 4
Description Features
The SB1i sensor box is packaged in a solid and Specially designed Aluminium housing
compact pressure-cast Aluminum housing with an for extra stable sensor platform with
integrated sensor for single axis inclination or sea water resistant coated finish
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
acceleration measurements.
IP65 to IP67 Environmental Protection
Within the box are 2 sections: An amplifier with a
4…20mA output signal - allowing a 2-wire system; 4…20mA amplifier for 2- wire
and a separate highly stable power supply for the connection
sensor. The amplifier contains a low-pass filter for Temperature compensation beyond the
upper frequency limitation, with noise suppression sensors own compensation data
filtering and a diode bridge for the unipolar
current-loop operation. Both sensor and amplifier No extra power required
are galvanically isolated from the housing -
Angle measuring range can be scaled to
further reducing susceptibility to outside noise.
customer requirements
Specific response time constants and maximum
current output limitations are additional options. Sensor and amplifier are galvanically
For a higher degree of accuracy, an NG-type sensor separated from the housing
can be integrated into the SB1i box, which Extensive EMC protection
considerably reduces temperature drift over the
entire temperature range. Add a strong metal PG Highly stable sensor supply voltage
The content presented is provided for informational purposes only and subject to change.
cable fixing combined with the 2-wire current-loop Dynamic parameters are programmable
output the SB1i provides a high-quality system for
use under many types of harsh working conditions. Current-loop with maximum current
limitation
Applications
High overload resistance
The SB1i is used where inclination or acceleration
measurements need to be combined with a 4…20mA Reverse polarity protected
current-loop output: especially where noise and/or Low-pass signal filter with optional
distance to source are a concern. Typically used in setting of maximum frequency for
FORM NUMBER: SK0013_08/02 UPDATED: 10/07
SB1i (4-20mA)
Single Axis Inclinometer Sensor Package
® Page 2 of 4
TECHNICAL DATA
2
Termination/Cable Diameter max.: 3 x 1.5 mm / Ø 5 ... Ø7 mm
Cable Fixing PG7 (Metal with integrated stress relief)
Measuring Ranges In accordance with the actual sensor
Protection Degree IP65 (with RTV fill IP67)
Mounting Any direction
N Series: 3 directions of mounting
Inclinometer Measuring Plane
NG Series: Parallel to the base of housing
Accelerometer Measuring Directions B, BD Series: Place in X, Y, Z co-ordinates to the housing
Supply voltage to the box +8 ... +30 Volt
Minimum loop current 3mA
Maximum loop current Approx.24mA
Output current loop signal 4...20mA (12mA as zero point)
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
The SB1i Sensor Box is extremely versatile, allowing various configurations with other Rieker sensors. If you have an
application that requires alternative specifications, one of our engineers will be happy to discuss how to customize the box for
your inclination or acceleration needs.
SB1i (4-20mA)
Single Axis Inclinometer Sensor Package
® Page 3 of 4
SB1i (4-20mA)
Single Axis Inclinometer Sensor Package
® Page 4 of 4
NOTES: Since the supply voltage for the SB1i is obtained from the current-loop and requires a max. 3mA, an input voltage of 9
The content presented is provided for informational purposes only and subject to change.
Volts/min. must be present at the connection block. This is also required in order to guarantee correct operation when the
highest loop current of approximately 24mA is used.
FORM NUMBER: SK0013_08/02 UPDATED: 10/07
©2002-2007 Rieker® Inc. All Rights Reserved.
SB1S
Electronic Sensor Box
Page 1 of 3
RIEKER
®
Description
The SB1S sensor box is packaged in a solid and compact pressure-cast aluminum housing with an
integrated sensor for single axis inclination or acceleration measurements.
Within the box are 2 sections: An amplifier with a 0…5VDC output signal; and a separate highly stable
power supply for the sensor, which can also be used as an external reference Voltage! The amplifier
contains a low-pass filter for upper frequency limitation, with noise suppression filtering and a diode
bridge that guarantees the electromagnetic compatibility. Both sensor and amplifier are galvanically
isolated from the housing - further reducing susceptibility to outside noise. Specific response time
constants and maximum current output limitations are additional options.
©2002 Rieker® Inc. All Rights Reserved. Updated: 8/02
The SB1S also has two Open-Collector outputs. The trigger point for thresholds can be individually
adjusted by means of two trim-potentiometers, this within the whole working range of the actual
sensor. Optionally, these can also be supplied as 1: Normally open 2: Normally closed.
For a very high degree of accuracy, an NG-type sensor can be integrated into the SB1S box, which
considerably reduces temperature drift over the entire temperature range. The strong metal PG cable
fixing combined with high voltage signal output make the SB1S a high-quality system for use under
many types of harsh working conditions.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SB1S
Electronic Sensor Box
Page 2 of 3
RIEKER Applications
®
ELECTRONICS INC
The SB1S is recommended where accurate inclination or acceleration measurements with a high level
5VDC voltage output are combined with the need for switching outputs – primarily for valve control and
safety purposes. It has been used in building construction, mining, radar systems, bridges, ships,
agricultural equipment, and all types of process machinery.
Technical Data
Termination/Cable diameter max.: Max.: 6 x 1 mm2 / Ø 5 ... Ø7 mm
Cable fixing PG7 (Metal with integrated stress relief)
Measuring ranges In accordance with the actual sensor
Protection degree IP65
Mounting Any direction
Sensor measuring plane
3 directions of mounting
(N Series)
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker®.
sensors. If you have an application that requires alternative specifications, one of our engineers will
be happy to discuss how to customize the box for your inclination or acceleration needs.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SB1S
Electronic Sensor Box
Page 3 of 3
RIEKER
®
ELECTRONICS INC
SB1S Dimensions (in mm) - Shown with NG-type Inclinometer Sensor
Excitation pot.
Zero pot.
cable fixing
NG-Sensor PG7
64mm
36mm
or other SW17
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker®.
connection
terminals
98mm
Housing hight: 36mm
all SEIKA-Sensors measuring channel
can be used in the galvanic separated
SB1S from housing
The open collector outputs are protected with diodes for spikes witching inductive loads
©2002 Rieker® Inc. All Rights Reserved. Updated: 8/02
CAUTION! Do not short-circuit the operating voltage (8 to 30V) with one of the outputs!
The OC outputs can optionally function as:
OC is connected to GND when the limit is exceeded - this is Version C
or OC is nonconnected to GND when the limit is exceeded - this is Version N
The version C offers the possibility to connect both OC outputs (wired OR) as only one
control signal (e.g. beep) to be activated, while passing one or the other limit.
The version N gives the possibility of greater alarm safety since an open-line condition
and operating power failure will cause an overriding of the limiting value and then cause an
alarm output.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SB1U (0-5V)
Single Axis Inclinometer Sensor Package
Page 1 of 2
®
Features
Description
The SB1U sensor box is packaged in a solid and compact pressure-cast aluminum housing with an
integrated sensor for single axis inclination or acceleration measurements.
The content presented is provided for informational purposes only and subject to change.
Within the box are 2 sections: An amplifier with a 0…5VDC output signal; and a separate highly stable
power supply for the sensor, which can also be used as an external reference Voltage! The amplifier
contains a low-pass filter for upper frequency limitation, with noise suppression filtering and a diode
bridge that guarantees the electromagnetic compatibility. Both sensor and amplifier are galvanically
isolated from the housing - further reducing susceptibility to outside noise. Specific response time
constants and maximum current output limitations are additional options.
For a very high degree of accuracy, an NG-type sensor can be integrated into the SB1U box, which
considerably reduces temperature drift over the entire temperature range. Add a strong metal PG
cable fixing combined with the 2-wire current-loop output the SB1U provides a high-quality system for
use under many types of harsh working conditions.
FORM NUMBER: SK0006_08/02 UPDATED: 01/07
©2002-2007 Rieker® Inc. All Rights Reserved.
Applications
The SB1U is used where inclination or acceleration measurements need to be combined with a high
level DC output. It has been used in building construction, mining, radar systems, bridges, ships,
agricultural equipment, and all types of process machinery.
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SB1U (0-5V)
Single Axis Inclinometer Sensor Package
Page 2 of 2
®
Technical Data
Termination/Cable diameter max.: Max.: 6 x 1 mm2 / Ø 5 ... Ø7 mm
Cable fixing PG7 (Metal with integrated stress relief)
Measuring ranges In accordance with the actual sensor
Protection degree IP65
Mounting Any direction
Sensor measuring plane
3 directions of mounting
(N Series)
Sensor measuring plane
Parallel to the base of housing
(NG Series)
Accelerometer measuring directions
Place in X, Y, Z coordinates to the housing
(B or BD Series)
Supply voltage to the box +8 ... +30 Volt
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
Caution ! The supply voltage (8 to 30V) must NOT be incorrectly connected to any output signal.
34 Mount Pleasant Road • Aston • PA • 19014 • USA
voice: 610-500-2000 fax: 610-500-2002 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SB2G (0-5V)
Dual Axis Inclinometer Sensor Package
® Page 1 of 2
Rugged, Environmentally
Sealed Inclinometer Package
with Two Integrated NG
Sensors and Signal Amplifiers,
Providing Temperature
Compensated Dual Axis
Analog 0…5V Output
Features Description
Rugged pressure die-cast Aluminium The SB2G sensor box is packaged in a solid and
housing with saltwater resistant coating compact pressure-cast aluminum housing with two
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
Highly stable sensor supply voltage The NG sensors add a very high degree of accuracy
The content presented is provided for informational purposes only and subject to change.
SB2G (0-5V)
Dual Axis Inclinometer Sensor Package
® Page 2 of 2
TECHNICAL DATA
2
Termination/Cable Diameter max.: 6 x 1 mm / Ø 5 ... Ø7 mm
Cable Fixing M12 x 1.5 cable gland, clamping range 6mm ... 7.5mm
Measuring Ranges In accordance with selected NG sensor
Protection Degree IP65 (with RTV fill IP67)
Mounting Wall mounted, flat vertical surface
Sensor Measuring Planes Parallel and 90° to the base of the housing
Supply voltage to the box +8 ... +30 Volt
Output current Approx. 12mA
Measuring range of output signal +0.5 to +4.5 Volt
Maximum range of output signal +0.05 to +4.95 Volt
Reference initial voltage (5+/-0.005) Volt (max. 10mA)
Output impedance 100
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
The SB2GSensor Box is extremely versatile, allowing various configurations. If you have an application that requires
alternative specifications, one of our engineers will be happy to discuss how to customize the box for your inclination or
acceleration needs.
Attention! Do not short circuit the supply voltage with one of the outputs.
SB2i (4-20mA)
Dual Axis Inclinometer Sensor Package
® Page 1 of 4
Features Description
Rugged pressure die-cast Aluminium The SB2i sensor box is packaged in a solid and
housing with saltwater resistant coating compact pressure-cast aluminum housing with
two integrated sensors for dual axis inclination
IP65 to IP67 Environmental Protection or acceleration measurements.
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
2 integrated signal conditioners with 4- Within the box are 2 amplifier sections, each
20mA, 2-wire outputs with 4…20mA output signal, which allows for
Temperature drift compensation two separate 2-wire systems; and a separate
highly stable power supply for the sensor. The
No extra power required amplifiers contain a low-pass filter for upper
frequency limitation, with noise suppression
Angle measuring range can be scaled to
filtering and a diode bridge for the unipolar
customer requirements
current-loop operation. Both sensor and
Compatible with B, BD, N, and NB types amplifier are galvanically isolated from the
housing - further reducing susceptibility to
Sensor and amplifier are galvanically outside noise. Specific response time constants
separated from the housing and maximum current output limitations are
Extensive EMC protection additional options.
Highly stable sensor supply voltage For a higher degree of accuracy and a
considerably reduced temperature drift over the
The content presented is provided for informational purposes only and subject to change.
Programmable dynamic response entire operating temperature range, the SB2i box
is optimized with special temperature
Current-loop with maximum current compensation. Add a strong metal PG cable fixing
limitation combined with the 2-wire current-loop output the
High overload resistance SB2i provides a high-quality system for use under
many types of harsh working conditions.
Reverse polarity protected - possibility of
3-wire connection for both measuring loops Applications
Low-pass signal filter with optional setting The SB2i is used where inclination or acceleration
FORM NUMBER: SK0028_08/02 UPDATED: 01/07
SB2i (4-20mA)
Dual Axis Inclinometer Sensor Package
® Page 2 of 4
TECHNICAL DATA
2
Termination/Cable Diameter max.: 6 x 1 mm / Ø 5 ... Ø7 mm
Cable Fixing M12 x 1.5 cable gland, clamping range 6mm ... 7.5mm
Measuring Ranges In accordance with selected sensor
Environmental Protection Rating IP65 (with RTV fill IP67)
Mounting Any direction
Inclinometer Measuring Plane N Series: 3 directions of mounting
Accelerometer Measuring Directions B, BD Series: Place in X, Y, Z co-ordinates to the housing
Supply Voltage +8 ... +30 VDC non-regulated
Minimum Loop Current 3mA
Maximum Loop Current Approx.24mA
Output Current Loop Signal 4...20mA (12mA as zero point)
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
The SB2i Sensor Box is extremely versatile, allowing various configurations. If you have an application that requires
alternative specifications, one of our engineers will be happy to discuss how to customize the box for your inclination or
acceleration needs.
SB2i (4-20mA)
Dual Axis Inclinometer Sensor Package
® Page 3 of 4
SB2i (4-20mA)
Dual Axis Inclinometer Sensor Package
® Page 4 of 4
NOTES: Since the supply voltage for the SB2i is obtained from the current-loop and requires a max. 3mA, an input voltage of
9 Volts/min. must be present at the connection block. This is also required in order to guarantee correct operation when the
highest loop current of approximately 24mA is used.
FORM NUMBER: SK0028_08/02 UPDATED: 01/07
©2002-2007 Rieker® Inc. All Rights Reserved.
SB360
Full 360º Inclination Sensor Box
Page 1 of 3
RIEKER
®
Features
Integrated NG360 inclination sensor with Possibility of connecting 78 units of
RS485 data interface SB360, NG360, XB360 on 4 wire bus
Rugged IP65 rated die-cast aluminum Stable 4 point attachment of 3.2mm
housing with seawater resistant finish base circuit board
High Shock Resistance NG360 galvanically isolated from housing
Cable junctions on both sides allowing Integrated EMV protection
inclinometers to be chained together
RS485 cable can be terminated with 100
especially for applications with rough
Ohm load by solder connection on board
environmental conditions
Identical performance to NG360
The content presented is provided for informational purposes only and subject to change.
Description
The SB360 is a single axis 360° inclination sensor integrating the NG360 within an aluminum die cast
metal housing rated to IP65. Also included within the box are EMV protection circuitry and a solder
pad for selecting internal or external cable termination. Two PG style liquid tight metal cord grip
fittings on either side of the compact metal enclosure along with the RS485 interface enable multiple
inclinometers to be linked together under rough operating conditions. The interface circuit and the
available addresses permit the user to connect a maximum of 78 sensor boxes to a 4-wire bus (2
conductors for the sensor power and 2 conductors for the RS485 data line).
The SB360 includes all the standard features of the NG360 including the integrated 16-bit
FORM NUMBER SK0011_10/02 Updated: 03/04
©2002-2004 Rieker® Inc. All Rights Reserved.
microprocessor, which provides for linearity and temperature compensation, and an EEPROM, which
stores the calibration data and dynamic control functions. The SB360 is also supplied with a set-up
program and communication/angle indication program for viewing the angle real time. Both
programs are written for Windows 95/98.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SB360
Full 360º Inclination Sensor Box
Page 2 of 3
RIEKER
®
ELECTRONICS INC
Applications
The SB360 can be used anywhere, including rough environments where exact deviation measurements
with an unlimited 360° measuring range is required. In particular, the SB360 has been used with
success in the building and mining industries, agricultural machinery, transportation equipment,
ships, and in process and automatic control engineering as well as general mechanical engineering.
Options
Inspection Report, Silicone Filled Housing, Custom Cable
If you have an application that requires alternative specifications, one of our engineers will be
FORM NUMBER SK0011_10/02 Updated: 03/04
happy to discuss how to customize the box for your inclination or acceleration needs.
©2002-2004 Rieker® Inc. All Rights Reserved.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SB360
Full 360º Inclination Sensor Box
Page 3 of 3
RIEKER
®
ELECTRONICS INC
Measurement Channel
galvanically isolated from
housing.
2 M4 Mounting Screws
Box Box
+Ub +Ub
-Ub = int.GND -Ub = int.GND
B (RS485) B (RS485)
A (RS485) A (RS485)
Shield = int.GND Shield = int.GND
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBS1U
Servo Inclinometer
Page 1 of 3
RIEKER
®
environmentally sealed
servo inclinometer
with ±5 Volt output
signal.
Features
Servo inclinometer with ±1° measurement Sensor and voltage scaling galvanically
range and extremely good resolution isolated from housing
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
±5V output signal for use with long signal EMC Protected
cables and reduced error susceptibility
Highly stable internal voltage regulator
Rugged IP65 rated pressure-cast aluminum
Reverse voltage polarity protected
housing with seawater proof finish
High mechanical shock resistance
12VDC ± 20% supply voltage
Internal low pass filter for interfering
Output signal calibration to customer’s
frequency suppression
specifications
Description
The SBS1U sensor box is packaged in a solid and compact pressure-cast aluminum housing (IP65) with
an integrated sensor for highly sensitive single axis inclination or acceleration measurements.
Within the box are 2 sections: a voltage amplifier with a ±5 Volt output signal and a separate highly
stable voltage regulator that supplies power to the sensor. The amplifier also contains an active low
The content presented is provided for informational purposes only and subject to change.
pass filter to suppress interference signals and transient suppression to ensure conformance to EMV
regulations. The sensor and the amplifier are galvanically isolated from the housing to avoid
interference from signals generated by undefined earth currents. An asymmetric 0 to 5V or a
symmetrical ±5V analog voltage signal, each mutually inverse, can be measured on both signal
outputs. The tightly sealed PG metal cable connector and the compact dimensions of the 100% metal
sensor housing enable this high quality measurement system to be used under severe operating
conditions.
Applications
The SBS1U is recommended for use where extremely precise inclination and acceleration
measurements must be taken under difficult conditions and harsh environments. Typical applications
©2002-2004 Rieker® All Rights Reserved.
include stability monitoring in the building, machinery, and construction industries as well as
inclination monitoring of bridges, dams, towers, tunnels, slopes, and of all structures where there is
risk of earthquakes or collapse.
FORM SK001-6/03
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBS1U
Servo Inclinometer
Page 2 of 3
RIEKER
®
Options
Special measuring ranges, test report, silicone filled housing, custom cable
©2002-2003 Rieker® All Rights Reserved.
If you have an application that requires alternative specifications, one of our engineers will be
happy to discuss how to customize the box for your inclination or acceleration needs.
FORM SK001-6/03
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBS1U
Servo Inclinometer
Page 3 of 3
RIEKER
®
ELECTRONICS INC
SBS1U Dimensions (in mm) and Terminal Connections
Amplification Adjust
Measurement channel
and supply voltage
galvanically isolated
from the housing.
Bridge Shield
Cable
©2002-2003 Rieker® All Rights Reserved.
FORM SK001-6/03
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBL1
Inclination Sensor Box
Page 1 of 3
RIEKER
®
ELECTRONICS INC
The SBL1 is a rugged,
sensor box with one
sensor & an integrated
power supply for a
4…20mA current-loop
output.
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker®.
Features
Highly stable die-cast aluminium housing The SBL1 unit will be supplied with
customer specific measurement ranges
Angle adjustable vibration dampers
mounted to support the 3.2mm Sensor and current-loop are galvanically
motherboard separated from each other
Built-in current amplifier for a 4...20mA EMC protections are standard
current-loop output
Highly stable sensor supply
Temperature compensation
Current-loop with max. limitation
No need for extra supply power
Very high mechanical overload
All N- or NG-type sensors can be
Non-polarity restrictions
integrated into the SBL1 and mounted in
different sensing directions Low-pass filtering with optional choice of
The content presented is provided for informational purposes only and subject to change.
Description
The SBL1 sensor box is packaged in a solid die-cast aluminum housing (IP54) with an integrated
sensor for single axis inclination measurements.
Within the box are 2 sections: An amplifier with a 4…20mA current-loop output proportional with
the working range of the integrated sensor and a separate highly stable power supply for the sensor,
which obtains its power from the 8…30VDC box supply. Both sensor and amplifier are galvanically
©2002 Rieker® Inc. All Rights Reserved. Updated: 8/02
isolated from the housing - further reducing susceptibility to outside noise. A custom low-pass filter
and a suppression filter combine to eliminate interference coming into the system.
For a very high degree of accuracy, an NG-type sensor can be integrated into the SBL1 box, which
considerably reduces temperature drift over the entire temperature range.
Applications
The SBL1 is recommended for use where inclination measurements are needed where mechanical
vibration occurs in such areas as conveyor systems, mining and agricultural equipment, and all types
of process machinery.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBL1
Inclination Sensor Box
Page 2 of 3
RIEKER
®
ELECTRONICS INC
Technical Data
Termination/Cable diameter Max.: 3 x 1.5 mm2 (2 x Signal + 1 x Mass)
Cable Diameter Ø12…Ø21,5mm
Cable fixing PG21 (Metal with strain relief)
Measuring ranges In accordance with the actual sensor
Protection degree IP54
Mounting Any direction
Sensor measuring plane
3 directions of mounting
(N Series)
Sensor measuring plane
Parallel to the base of housing
(NG Series)
Supply voltage to the box +8...+30 Volt
Minimum current Approximately 3mA
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker®.
Since the supply voltage for the SBL1 are obtained from the current loop and the SBL1
requires max.3mA, an input voltage of 9Volts min. must be supplied at the connection
block of sensorbox.This is also required in order to guarantee correct operation when
the highest loop current of approx.24 mA is used.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBL1
Inclination Sensor Box
Page 3 of 3
RIEKER
®
178
160
Measurement angle
Solder
terminal
time
constant
1 sec.
2 sec.
Zero potentiometer
NG-Sensor
or other type
SEIKA-Sensor
160
178
Excitation potentiometer
The content presented is provided for informational purposes only and subject to change.
©2002 Rieker® Inc. All Rights Reserved. Updated: 8/02
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBL1S
Inclination Sensor Box with Safety Control
Page 1 of 4
RIEKER
®
ELECTRONICS INC
The SBL1S has two
sensors each on its own
channel: one channel
with a 4…20mA current-
loop output & one
channel with a 0…5VDC
output including two
safety relays with set-
point regulation of
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker®.
range.
Features
Highly stable die-cast aluminium housing The SBL1S unit will be supplied with
customer specific measurement ranges
Angle adjustable vibration dampers
mounted to support the 3.2mm Sensor and current-loop are galvanically
motherboard separated from each other and housing
Built-in current amplifier for 4...20mA EMC protections are standard
current-loop output and 0..5 VDC output
Highly stable sensor supply
All N-, NB- or NG-type sensors can be
Very high mechanical overload
integrated into the SBL1 and mounted in
The content presented is provided for informational purposes only and subject to change.
Channel 1 Channel 2
4...20mA current-loop output Voltage amplifier with 0..5 VDC signal output
Temperature compensated Temperature compensated
No need for extra supply power Highly stable sensor supply
Non-polarity restrictions Opporating voltage reverse polarity protected
©2002 Rieker® Inc. All Rights Reserved. Updated: 8/02
Current-loop with max. limitation Two separate, individually variable safety relays
each with double functions on ± inclincation
Description
The SBL1S sensor box is packaged in a solid die-cast aluminum housing (IP54) with two integrated
sensors with a separate highly stable power supply for both sensors, which obtains its power from
the 8…30VDC box supply.
Each sensor has its own channel: Channel 1 - One amplifier with a 4…20mA current-loop output
proportional with the working range of one of the integrated sensors and Channel 2 – the other
sensor provides a 0…5VDC output and controls the safety relays. Both sensors and amplifier are
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBL1S
Inclination Sensor Box with Safety Control
Page 2 of 4
RIEKER
®
galvanically isolated from the housing - further reducing susceptibility to outside noise. A custom
ELECTRONICS INC low-pass filter and a suppression filter combine to eliminate interference coming into the system.
The two adjustable set-points are linked to the voltage source of the box. There is a double safety-
relay function for both plus and minus inclination. Optional adjustment of the switching hysteresis is
available on request.
For a very high degree of accuracy, an NG-type sensor can be integrated into the SBL1S box, which
considerably reduces temperature drift over the entire temperature range.
The SBL1S - with a double securing ON/OFF safety control system with both current and voltage signal
outputs - provides a very stable and strong inclination measuring system for utilization under harsh
circumstances.
Applications
The SBL1S is recommended for use where inclination measurements require a full-proof safety system,
especially where mechanical vibration occurs in such areas as conveyor systems, mining and
agricultural equipment, and all types of process machinery.
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker®.
Technical Data
Connections Max.: 15 x 1 mm2 (screw connectors)
Cable Diameter Ø12…Ø21,5mm
Cable fixing PG21 (Metal with strain relief)
Measuring ranges In accordance with the actual sensor
Protection degree IP54
Mounting Any direction
Sensor measuring plane
3 directions of mounting
(N, NB Series)
Sensor measuring plane
Parallel to the base of housing
(NG Series)
Operating temperature -40...+85°C
The content presented is provided for informational purposes only and subject to change.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SBL1S
Inclination Sensor Box with Safety Control
Page 3 of 4
RIEKER
®
ELECTRONICS INC Two SIEMENS safety relays (type SR2A311) – which meet
Switching stages the safety and technical regulations for usage as
safeguard relays
Each relay furnished with an independent Open and
Contacts
Closing contact
Contact load 250V, 6A
Signal zero (2.5V), amplifier, under- and over-trigger
Adjustable potentiometers
threshold
Low-pass filter Active, 4th order, minimum ripple
Options
Special measuring ranges, special hysteresis, test report
178
160
Measuring angle
The content presented is provided for informational purposes only and subject to change.
LED
Relay
Relay
©2002 Rieker® Inc. All Rights Reserved. Updated: 8/02
Cable fixing
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker®.
The content presented is provided for informational purposes only and subject to change.
©2002 Rieker® Inc. All Rights Reserved. Updated: 8/02
®
ELECTRONICS INC
RIEKER
®
Excitation potentiometer
Zero (2,5V) potentiometer
Zero (12mA) potentiometer
Excitation potentiometer
voice: 610-534-9000
Solder terminal - time constant 2 sec.
Solder terminal - time constant 1 sec.
Solder terminal - time constant 1 sec.
Solder terminal - time constant 2 sec.
both solder terminals - time constant 3 sec. both terminals - time constant 3 sec.
fax: 610-534-4670
for adjustment of the
angle limit/set point Typ: SBL1S
(clock wise >>> right)
(anti clock w.>>> left) SIEMENS
safety relays S.-Nr.:
LED left limit
Power supply 12 Volt / 24 Volt
Potentiometer left limit SIEMENS connector (3) :
safety relays
LED right limit Measuring I
4...20 mA : - /+ Grad
Potentiometer right limit
Measuring U
0.5...4.5 Volt : - /+ Grad
email: info@riekerinc.com
GND (2) (14) 4...20 mA current loop
hysteresis : ca. Grad
SBL1 Wiring Connections and Set-Points
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
Email: ranjin@riekerinc.com
Caution! Do not short circuit the operating voltage (8...30V) with one of the outputs
web: www.riekerinc.com
Inclination Sensor Box with Safety Control
Page 4 of 4
SBL1S
®
BS24
Sensor Mounting Cube
Page 1 of 1
Technical Data
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
Material Aluminum
Weight without sensors 1.13 Ounces (32 Grams)
Weight with sensors 3.5 Ounces (99 Grams)
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
SW3
Sensor Mounting Cube
Page 1 of 1
RIEKER
ELECTRONICS INC The “Cube” allows for
mounting multiple sensors for
Tri-axial inclination and/or
acceleration measurements.
Description
The SW3 Sensor Cube can be used for mounting the
following Seika sensors: The N3, N4, or NB3 Inclinometers
and/or the B, BD, or BDK Accelerometers, which can be
mounted into this cube in customer specified combinations.
Technical Data
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
ATTENTION: When ordering an SW3 that is to be utilized with an NV6a Signal Conditioner, you
must specify that it is an ISOLATED SENSOR MOUNTING; or NON-ISOLATED SENSOR MOUNTING
for either an NV4a or NV8a.
PO Box 127 • 777 Henderson Blvd • Park Square North Bldg • Bay #7 • Folcroft • PA • 19032 • USA
voice: 610-534-9000 fax: 610-534-4670 email: info@riekerinc.com web: www.riekerinc.com
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
XB Series
Extreme Conditions Inclinometer Package
Page 1 of 2
Formidable Protection
Against Extreme &
Underwater
Environments,
Aggressive Media, and
Seawater – a Heavy-Duty
Sensor Package.
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Corrosion resistant
pressure load.
Rigid 4 point attachment of 3.2mm base
©2002-2007 Rieker® Inc. All Rights Reserved.
TECHNICAL DATA
2
TERMINAL CONNECTION Maximum: 2 x 1.5 mm (2 x 16 AWG)
RANGE, RESOLUTION, OUTPUT According to sensor used
SENSING POSITION Arbitrary
SB1, SB2 (N) 3 main Housing Directions
INCLINATION PLANE
SB1, (NG) Parallel to the Housing Bottom
ACCELERATION PLANE SB1, SB2 (B, BD, BDK) X, Y, Z-coordinates of Housing
ELECTRICAL VALUES According to the Appropriate SB Sensor Box Requirements
MECHANICAL CHARACTERISTICS
HOUSING Stainless Steel V4A (seawater resistant)
PRESSURE STRENGTH 10 bar (1Mpa), 100 meters below sea level
ENVIRONMENTAL PROTECTION IP68
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
INPUT/OUTPUT Cable Entry PG9 (V4A steel with integrated strain relief, handles 8-10mm cable diameter)
CONNECTION Patch Cord SubConn® Underwater Plug Connector
WEIGHT 4 lbs (1,82 kilograms) (not including cable)
OPERATING TEMPERATURE -40°F to +185°F (-40° to +85°C )
STORAGE TEMPERATURE -49°F to +194°F (-45° to +90°C )
Thoroughly grease
cover threads and
gasket before
sealing!!
The content presented is provided for informational purposes only and subject to change.
Shown
Mounted
Vertically
Ø 140mm (5.52”)
100mm (3.94”)
PG9 or
FORM NUMBER: SK0010_10/02 UPDATED: 01/07
Subconn
Underwater
Connector
©2002-2007 Rieker® Inc. All Rights Reserved.
Housing Height:
49mm (1.92”)
Features Description
Single and Dual Axis ± Trip Angles SlopeAlert is a reliable, low cost solution of
determining in-range and out of range tilt conditions.
Normally Open or Closed Output
Connected to a lamp, horn, or solenoid relay, this
Lamp / Buzzer / Solenoid Driver compact Single or Dual Axis unit can indicate both safe
and unsafe conditions as well as provide a control
Single Supply Input (8-30VDC)
signal to help prevent equipment over rotation.
Reverse Polarity Protection Multiple trip settings are factory calibrated and can be
arranged in a single axis to indicate caution before
Output Short Circuit Protected final alarm. SlopeAlert is available in both Normally
High Current-Sink Capability Open and Normally Closed outputs.
Inductive Load Protection
Applications
-40°C to +75°C Operating The SlopeAlert tilt indicator was designed for off-road,
Temperatures in-motion vehicles and equipment that operate in high
The content presented is provided for informational purposes only and subject to change.
Input Parameters
Standard Trip Point Settings ±10, ±15, ±20, ±25, ±30, ±35, ±40, ±45°
Standard Input 5° Increments (custom 1º increment settings available)
Standard: Non-regulated: 8 to 30 VDC
Power Supply
Optional: Regulated: 5 VDC
Current Consumption 30 mA typical (60 mA maximum)
Output Parameters
Trip Setting ±1°
Actuation Repeatability ±2°
Continuous Collector Current 1.0 Amps
Output Saturation Voltage 0.4 V max.
Standard: Normally Open for out of range indication
Open Collector Switch Output
Optional: Normally Closed for in range indication
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Maximum Ratings
Supply Voltage 35 VDC (35 VDC+ Available upon request)
Reverse Battery Voltage 50 VDC
Output Voltage Collector Emitter (VCEO): 50 VDC
Output Transistor Collector Base (VCBO): 50 VDC
Output Transistor Emitter Base (VEBO): 5 VDC
Output Collector Current 1.5 Amps
Operating Temperature -40°C to +75°C
Storage Temperature -40°C to +85°C
Mechanical Characteristics
Noryl Plastic with filled Epoxy (equivalent to IP67 Protection)
Housing
Optional Painted Aluminum Enclosure
Mounting Two #8 screws
Outline Dimensions 2.86” x 2.08” x1.50” (72.6 x 52.8 x 38.1mm)
The content presented is provided for informational purposes only and subject to change.
Figure 1: Dimensions for Single Axis SlopeAlert Noryl Enclosure (inches / mm)
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
Figure 2: Dimensions for Dual Axis SlopeAlert Noryl Enclosure (inches / mm)
The content presented is provided for informational purposes only and subject to change.
©2002-2007 Rieker® All Rights Reserved.
RT0010_06/03 UPDATED: 02/07
Figure 3: Dimensions for Dual Axis SlopeAlert Aluminum Enclosure (inches / mm)
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
NOTES:
1. CONNECT DIODE TO SUPPLY VOLTAGE WHEN USING INDUCTIVE LOADS.
2. UNIT IS SUPPLIED WITH A 4 CONDUCTOR NON-SHIELDED CABLE. IF THE OPTIONAL SELF-TEST FEATURE IS
SELECTED, A FIFTH WIRE WILL BE PROVIDED. MOMENTARILY CONNECTING THIS SELF TEST WIRE TO
GROUND WHEN THE UNIT IS IN A LEVEL POSITION WILL SIMULATE AN OUT OF RANGE CONDITION AND WILL
ACTIVATE THE SWITCH.
OPTION
CODE
CASE CONFIGURATION
SINGLE AXIS WITH NORYL ENCLOSURE (Default) S
SINGLE AXIS WITH PAINTED ALUMINUM ENCLOSURE T
DUAL AXIS WITH NORYL ENCLOSURE A
DUAL AXIS WITH PAINTED ALUMINUM ENCLOSURE B
DUAL SENSORS SAME AXIS WITH NORYL ENCLOSURE C
DUAL SENSORS SAME AXIS WITH PAINTED ALUMINUM ENCLOSURE D
Note, insert higher switch setting if both sensors measure same axis.
Other angles are available upon request.
INPUT POWER
8 TO 30VDC (Default) BLANK
5VDC V
OUTPUT CONFIGURATION
NORMALLY OPEN (Default) BLANK
NORMALLY CLOSED C
LED OPTION
NO LED (Default) BLANK
ONE RED LED G
ONE GREEN LED H
ONE YELLOW LED AND ONE RED LED K
ONE RED LED AND ONE BLUE LED L
OTHER, PLEASE EXPLAIN IN COMMENT BOX M
The content presented is provided for informational purposes only and subject to change.
BUZZER OPTION
NO BUZZER (Default) BLANK
CONSTANT ALARM X
PULSING ALARM Y
ONE PULSING ALARM AND ONE CONSTANT ALARM Z
CABLE LENGTH
1 FOOT (Default) BLANK
2 FEET 2 As shown above the part number RTC1525TKZ6
4 FEET 3 represents a unit with dual sensors measuring the same axis. The
©2002-2007 Rieker® All Rights Reserved.
6 FEET 4 first trip setting is 15° and the larger trip setting is 25°. The box
8 FEET 5 uses an 8 to 30VDC input, works in a normally open configuration
RT0010_06/03 UPDATED: 02/07
10 FEET 6 (warns at out of range), includes the self test feature, and has
20 FEET 7 one yellow led that will light when 15°is exceeded and one red
30 FEET 8 led that will light when 25° has been exceeded. The box also has
two buzzers, one that is pulsing for the warning level and one
OTHER *
that is constant when 25° has been exceeded. A custom cable
length of 10 feet has also been requested.
* E and F RELAY options have the relay wiper internally connected to
12VDC or 24VDC respectively. Consult factory for optional external Although a SlopeAlert model is available with multiple options
wiring of relay wiper. certain options may not be available simultaneously.
Features
Description
Rieker manufacturers these inclinometers to MIL Spec, using precision glass tube and ball
construction with engraved markings and customer specified color warning zones. All our tubes are
The content presented is provided for informational purposes only and subject to change.
filled with a special dampening fluid that controls the movement of the ball. The fluid combined
with large, clear number and degree markings make it easy to get quick, accurate readings under a
wide variety of severe environmental conditions.
Custom Color Warning Zones
The color zone or "SPL" models are designed to instantly alert the operator of tip-over danger
utilizing highly visible color zones: e.g. RED = tip-over danger; GREEN = safe operation.
Please Note: The customer must specify the color zone degree ranges at time of order.
Applications
FORM NUMBER: MI0001_09/03 UPDATED: 01/07
These inclinometers are used on utility trucks, aerial lift trucks, cranes, construction equipment,
©2002-2007 Rieker® Inc. All Rights Reserved.
aircraft, boats, ships, submarines, fire trucks, military and government vehicles for leveling,
balancing and preventing tip-over.
1017
Degree Markings 2°
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
1017W1
Degree Markings 1°
1017SPL2* * Picture shown is a sample of customer specified color zones only. Color zones are
The content presented is provided for informational purposes only and subject to change.
Degree Markings 2°
1017SPL3* *Picture shown is a sample of customer specified color zones only. Color zones are
FORM NUMBER: MI0001_09/03 UPDATED: 01/07
Degree Markings 2°
Description
The content presented is provided for informational purposes only and subject to change.
Rieker Instrument Company Inc manufactures manual inclinometers using glass tube and ball
construction with engraved markings and customer specified color warning zones. All our tubes are
filled with a special dampening fluid that controls the movement of the ball. The fluid combined
with large, clear number and degree markings make it easy to get quick, accurate readings under a
wide variety of severe environmental conditions.
Custom Color Warning Zones
The color zone or "SPL" models are designed to instantly alert the operator of tip-over danger
utilizing highly visible color zones: e.g. RED = tip-over danger; GREEN = safe operation.
FORM NUMBER: MI0002_09/03 UPDATED: 01/07
Please Note: The customer must specify the color zone degree ranges at time of order.
Applications
©2002-2007 Rieker® Inc. All Rights Reserved.
Our inclinometers are used on utility trucks, aerial lift trucks, cranes, construction equipment,
aircraft, boats, ships, submarines, military and government vehicles for leveling, balancing and
preventing tip-over. The 1023 model was originally designed for DOT usage as a ball bank indicator
to help determine safe curve speed.
1023
Degree Markings 5°
1023W1
The information and material presented may not be published, broadcast, rewritten, or redistributed without the express written consent of Rieker® Inc.
Degree Markings 1°
1023N
Degree Markings 1°
Engraved markings filled fluorescent
yellow, glass tube with black ball on
fluorescent yellow background
1023SPL2*
The content presented is provided for informational purposes only and subject to change.
Degree Markings 5°
1023W1SPL3*
Degree Markings 1°
©2002-2007 Rieker® Inc. All Rights Reserved.
*Inclinometers shown are samples of customer specified color zones only. Color zones are dependent upon customer specified
degree ranges and color combinations. Model 1023 with custom color zones have extended part numbers, which are based on
specified degrees and number of zones.
Features
Description
The content presented is provided for informational purposes only and subject to change.
A Clinometer is any of various surveying instruments for measuring angles of elevation, slope, or incline,
with respect to gravity. Also called an Inclinometer or gradiometer, these precision instruments provide
accurate real-time measurement of slope in Degrees. Rieker manufacturers these manual type
inclinometers using precise glass tube and ball construction. All our tubes are filled with a special
damping fluid that controls the movement of the ball. The fluid combined with large, clear number
and degree markings make it easy to get quick, accurate readings under a wide variety of severe
environmental conditions.
Applications
Rieker Clinometers are the industry standard - typically used on sail boats and watercraft to indicate
FORM NUMBER: MI0006_08/05 UPDATED: 05/07
small changes in attitude and provide real time angle of the vessel. Other applications include aerial
lift/off-road material handlers, cranes, construction equipment, aircraft, submarines, military and
©2002-2007 Rieker® Inc. All Rights Reserved.
Degree Markings 5°
Description
Also called a clinometer or gradiometer, the 2064 Series provide accurate measurement of slope in
Degrees, Percent Grade and Inch Per Foot Rise. Rieker manufacturers these inclinometers to MIL
Spec, using precision glass tube and ball construction. All our tubes are filled with a special
dampening fluid that controls the movement of the ball, for a smooth accurate roll. The fluid
combined with large, clear number and degree markings make it easy to get quick, accurate readings
The content presented is provided for informational purposes only and subject to change.
2064
Degree Markings 2°
2064E
Degree Markings 2°
2064EG “Gradiometer”
*Please note that color zones are typically specified by the customer to indicate
certain conditions – ask your sales representative if you have a requirement.
FORM NUMBER: MI0005_04/05 UPDATED: 05/07
©2002-2007 Rieker® Inc. All Rights Reserved.
Off-road Forklifts, Material Rugged housing withstands weight of a full size Back lit version highly visible at
Handlers, Boom Lifts, Truck SUV! Meets OSHA Standards for Cranes and night – meets FEMA regulations
Mounted Cranes, etc. derricks. for fire apparatus.
DESCRIPTION FEATURES
Rieker's rugged manual boom angle indicators – the 4120 Oversized inclinometer for
Series - are not effected by outdoor elements. These easy read
instruments are made tough and will not rust, freeze, or High visibility markings
otherwise "hang up" like old-fashioned pendulum styles. Like Hermetically sealed – will
all of our manual instruments, each indicator is properly not leak
The content presented is provided for informational purposes only and subject to change.
retrofitting
Typical applications include aerial lifts, truck-mounted boom Right hand or left hand
cranes, any fire truck with a mounted boom or ladder, models available
©2002-2007Rieker® Inc. All Rights Reserved.
telescoping off-road variable reach fork lifts, cranes and Now available with 12 Volt
derricks, or any equipment that requires boom angle backlighting - highly visible
indication. at night for added safety
OEMs welcome, quantity pricing available.
http://www.osha-slc.gov/OshStd_data/1926_0550.html
<Then follow these breadcrumbs: > Regulations (Standards - 29 CFR) > PART 1926 Safety and Health Regulations for
Construction > 1926.550 - Cranes and derricks > 1926.550(a)(1)
4120WWL 412OWWR
4120WBL 4120WBR
4120BBL 4120BBR
4120WWL-12V 4120WWR-12V
2 Scales: Inch per Ft-Rise and % Grade Easily installed – quick retrofitting
Weatherproof - will not rust or hang up Quick and accurate visual reference
UV Resistant Operational from -50° F to +180° F
Extremely shock and vibration resistant
Description
A Gradiometer is any of various surveying instruments for measuring angles of elevation, slope, or
incline, as of an embankment or roadway. Also called clinometer or inclinometer, the 5012P provides
accurate measurement of slope in Percent Grade and Inch Per Foot Rise. Rieker manufacturers these
manual type gradiometers (or inclinometers) using precise glass tube and ball construction. All our
tubes are filled with a special dampening fluid that controls the movement of the ball. The fluid
The content presented is provided for informational purposes only and subject to change.
combined with large, clear number and degree markings make it easy to get quick, accurate readings
under a wide variety of severe environmental conditions.
Applications
Plows, graders, excavators, trenchers, and pavers are only a few examples of the types of
applications well suited for gradiometers.
RIEKER TERMS AND CONDITIONS: International Customers and Exporters must list the application, end use,
and final destination for any product being requested for quotation. All prices are based on shipment
ELECTRONICS INC
quantity. Pricing does not include shipping and handling.
TEL: (610) 534-9000
FAX: (610) 534-4670
There is a non-deductible $6.00 Handling Fee per shipment regardless of prepaid or freight collect
info@riekerinc.com
service. It is the purchaser’s responsibility to pay
www.riekerinc.com all duties and tax.
The purchaser will be responsible for any Bank charges incurred for processing wire transfers,
Canadian and/or International checks, or letters of credit. We have included in your invoice our bank
wire charges. Any other fees incurred by other banks are the responsibility of the customer. (Please
note that it is common for your bank as well as intermediate banks to charge a fee). Rieker may bill you
in addition to this invoice if Rieker is required to pay wire transfer fees incurred at your end.
Payment received within 30 days of order, are discounted (the deduction is included in the Net 30
quoted price). If Net 30-Day Terms are extended but payments are not made within 30 days, the
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
discounted price is subject to change. Net 60 terms are available, which are not discounted. NET 30
means that payment must be received within day 1 through day 30, NET 60 means that payment must
be received within day 31 through day 60. Payments received after the NET Terms extended are
subject to additional fees. All prices are based on shipment quantity.
ONE YEAR WARRANTY: The manufacturer of this quality instrument warrants that if Rieker
determines this instrument has failed, within twelve months of the date of purchase, due to defect in
material or workmanship, the company will repair or replace such instrument without cost to the
customer, provided that the instrument is returned prepaid to the company. IN NO EVENT WILL THE
COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OF ANY KIND.
You must obtain an RMA # from Rieker prior to shipping the defective items back to us.
ACCEPTANCE: This is an offer to sell our product on the terms and conditions written above and
should not be viewed as an acceptance of any other offer or agreement. Unless expressly agreed,
Rieker does not, and will not accept any changed or additional terms included in other documents. Any
additional or conflicting terms made a part of or attached to a purchase order will not be considered,
The content presented is provided for informational purposes only and subject to change.
and Rieker objects to any such terms. As such, you acknowledge that the terms stated herein are the
only terms in effect with respect to your purchase of these instruments. Any purchase order received by
Rieker will be considered acceptance of the terms stated in this document only.
CUSTOM ENGINEERING: Rieker is happy to make changes to our inclinometers based on customer
request, however this in no way implies any rights of ownership to the Customer.
Thank you for the opportunity to quote on your requirements. If you have any
questions, please contact us.
©2002-2006 Rieker® All Rights Reserved.
UPDATED: 04/07
China Office Tel: 010 - 8708 3686 Fax: 010 - 8256 1891 Email: ranjin@riekerinc.com
®
Contact Information
REI
Page 1 of 2
Dear Customer,
We are delighted to be considered a supplier for your company and would like to
take this opportunity to introduce you to your account representative. We pride
ourselves in attempting a 100% satisfaction rate with our customer base. Please
allow us to ensure the same service to you by communicating any requests or
complaints that you may have to your representative. They are authorized to divert
from policy when necessary in order to service your needs.
Contact Information
YOUR ACCOUNT REP: ACCOUNTS RECEIVABLE:
Cyndy Williams Christine Cassidy
The information and material presented may not be published, broadcast, rewritten, or redistributed without the expressed written consent of Rieker® Inc.
cwilliams@riekerinc.com ccassidy@riekerinc.com
Payments are due within the Net 30-day terms stated on our invoice. Invoices must be paid in full by
the due date. Delinquent accounts will incur a one and one-half percent charge per month on the
balance. Your net terms will be changed to a no-net term if we attempt to contact your accounts
payable representative and we do not receive a response within three business days. You may also
find your net terms changed if we do not receive a payment on the date indicated by your accounts
payable representative when we contact them. Payments may not be withheld due to anticipated
credits. Unauthorized deductions on invoices are not acceptable.
The content presented is provided for informational purposes only and subject to change.
Any billing disputes must be reported prior to the due date of the invoice to your Accounts
Receivable contact at (610) 500-2000 extension 2006.
International accounts may incur a bank charge on their invoice if paying by wire transfer. If
payments are made in U.S. Dollars by a bank, which has a branch in the United States, you may
deduct this charge since we will not be charged a fee in this case. Our E.I.N. # is 23-2858784.
If you require any additional information from us to set Rieker up as a vendor and/or to facilitate
payment please do so prior to the due date of all invoices. If you require any forms to be filled in
order to give us approved vendor status please fax to Christine Cassidy at 610-500-2002.
FORM NUMBER: RK0002_06/03 UPDATED: 05/07
©2002-2007 Rieker® All Rights Reserved.