Professional Documents
Culture Documents
Sikaflex - 252
Sikaflex - 252
Sikaflex®-252
Elastic adhesive for vehicle assembly bonding
1/2
CURE MECHANISM Consider that the viscosity will increase at low PACKAGING INFORMATION
Sikaflex®-252 cures by reaction with atmo- temperature. For easy application, condition
spheric moisture. At low temperatures the the adhesive at ambient temperature prior to Cartridge 300 ml
water content of the air is generally lower and use. To ensure a uniform thickness of the Unipack 600 ml
the curing reaction proceeds somewhat bondline it is recommend to apply the adhes-
slower (see diagram 1). ive in form of a triangular bead (see figure 1).
BASIS OF PRODUCT DATA
All technical data stated in this document are
based on laboratory tests. Actual measured
data may vary due to circumstances beyond
our control.
HEALTH AND SAFETY INFORMATION
For information and advice regarding trans-
Figure 1: Recommended bead configuration portation, handling, storage and disposal of
chemical products, users shall refer to the ac-
Sikaflex®-252 can be processed with manual, tual Safety Data Sheets containing physical,
pneumatic or electric driven piston guns as ecological, toxicological and other safety-re-
well as pump equipment. The open time is lated data.
significantly shorter in hot and humid cli-
mates. The parts must always be installed DISCLAIMER
Diagram 1: curing speed Sikaflex®-252 The information, and, in particular, the re-
within the open time. Never join bonding
CHEMICAL RESISTANCE parts if the adhesive has built a skin. commendations relating to the application
Sikaflex®-252 is generally resistant to fresh and enduse of Sika products, are given in
water, seawater, diluted acids and diluted Tooling and finishing good faith based on Sika's current knowledge
caustic solutions; temporarily resistant to Tooling and finishing must be carried out and experience of the products when prop-
fuels, mineral oils, vegetable and animal fats within the skin time of the product. It is re- erly stored, handled and applied under nor-
and oils; not resistant to organic acids, glycol- commended to use Sika® Tooling Agent N. mal conditions in accordance with Sika's re-
ic alcohol, concentrated mineral acids and Other finishing agents must be tested for suit- commendations. In practice, the differences
caustic solutions or solvents. ability and compatibility prior to use. in materials, substrates and actual site condi-
tions are such that no warranty in respect of
METHOD OF APPLICATION Removal merchantability or of fitness for a particular
Surface preparation Uncured Sikaflex®-252 can be removed from purpose, nor any liability arising out of any
Surfaces must be clean, dry and free from tools and equipment with Sika® Remover-208 legal relationship whatsoever, can be inferred
grease, oil, dust and contaminants. or another suitable solvent. Once cured, the either from this information, or from any writ-
The surface treatment depends on the specif- material can only be removed mechanically. ten recommendations, or from any other ad-
ic nature of the substrates and is crucial for a Hands and exposed skin have to be washed vice offered. The user of the product must
long lasting bond. Suggestions for surface pre- immediately using hand wipes such as Sika® test the product's suitability for the intended
paration may be found in the current edition Cleaner-350H or a suitable industrial hand application and purpose. Sika reserves the
of the appropriate Sika® Pre-treatment Chart. cleaner and water. right to change the properties of its products.
Consider that these suggestions are based on Do not use solvents on skin. The proprietary rights of third parties must be
experience and must be verified by tests on observed. All orders are accepted subject to
FURTHER INFORMATION our current terms of sale and delivery. Users
original substrates. The information herein is offered for general must always refer to the most recent issue of
guidance only. Advice on specific applications the local Product Data Sheet for the product
is available on request from the Technical De- concerned, copies of which will be supplied
Application
partment of Sika Industry. on request.
Sikaflex®-252 can be processed between
Copies of the following publications are avail-
10 °C and 35 °C (climate and product) but
able on request:
changes in reactivity and application proper-
▪ Safety Data Sheets
ties have to be considered. The optimum tem-
▪ Sika Pre-treatment Chart
perature for substrate and sealant is between
For 1-component Polyurethanes
15 °C and 25 °C. ▪ General Guidelines
Bonding and Sealing with 1-component
Sikaflex®
2/2