Professional Documents
Culture Documents
EPCM Recomm
EPCM Recomm
Sub: EPCM SERVICES FOR 02G ETHANOL BIOREFINERY ALONG WITH ASSOCIATED FACILITIES AT
VILLAGE NASIBPURA, BATHINDA, PUNJAB‐ Nomination PO recommendation due to additional
scope of Supply, Fabrication and Installation of items (not included in original SOR)
Ref: ‐
Letters received from M/s. Bridge & Roof Co. For Extra Items requirement and rate analysis:
B&R/61036/HPCL‐TANKAGE/106 dt. 08‐02‐2022
B&R/61036/HPCL‐TANKAGE/107 dt. 09‐02‐2022
B&R/61036/HPCL‐TANKAGE/133 dt. 25‐03‐2022
B&R/61036/HPCL‐TANKAGE/185 dt. 15‐07‐2022
B&R/61036/HPCL‐TANKAGE/215 dt. 15‐11‐2022
B&R/61036/HPCL‐TANKAGE/219 dt. 16‐12‐2022
B&R/61036/HPCL‐TANKAGE/254 dt. 01‐06‐2023
Dear Sir,
This has reference to PO NO.‐ 21000265‐OQ‐10120 Dated 01.09.2021 placed on Bridge & Roof.
There is requirement of additional items in the scope of B&R. During engineering development,
there have been additions of some nozzles which are required for the proper functioning / safety of
the tank and it is mandatory to procure these from B&R due to interface and testing requirements.
As B&R scope in the original PO is SOR based, these nozzles are an additional scope to the tender. A
nomination PO for the Supply, Fabrication and Installation is therefore recommended for these
additions.
Thanking you and assuring our best services all the time.
Best regards,
(RUCHI BHANDARKAR)
Procurement Manager.
Encl:
ANNEXURE 01: PRICE SCHEDULE & CALCULATION AND ANALYSIS OF PROPOSED RATE BY TECHNIP
ANNEXURE 02: REASONS FOR ADDITION OF NEW ITEMS
ANNEXURE 03: ACCEPTANCE LETTER FROM M/s BRIDGE & ROOF CO. OF TECHNIP PROPOSED RATES
20" CS Nozzle - Supply, fabrication, erection and welding of nozzle of 20 inch diameter with reinforcement pad plate, seamless pipes/ plate TK-9721, TK-
fabricated pipe, slip on flanges with drilled holes as per ANSI-B-16.5, gaskets, nut, bolts, washer, including Spares trough including installation as 9801A/B, TK-
3 EX. ITEM -15 20'' CS NOZZLE per specification. Reinforcement pad shall be tested with soap solution by applying pneumatic pressure of 1.05 kg/sq.cm before hydro testing.
NOS 7 123566.00 864962.00 Man-Machine-Material Analysis cost is INR 2,05,893.24
9803A/B/C, TK-
Contractor to supply all materials required for the nozzles. 9806
20'' CS UNDER-
20" Carbon Steel SR Elbow and associated pipe, flange, blind, gasket, nuts, bolts including Spares for tank Under-bottom connection. Design, supply,
4 EX. ITEM -19 BOTTOM welding and installation as required by specification.
TK-9721 NOS 1 579413.00 579413.00 Man-Machine-Material Analysis cost is INR 6,35,087.25
CONNECTION
CONC RED. 3'' X
As per recent order placed for 3" X 2.5" CRE S-STD S-XS Concentric reducer, Seamless, ASME
5 EX. ITEM -34 2.5'' SCH-STD X FITTINGS, Size: 3x2.5 Sch- STD X 160 Concentric Reducer, ASTM A105 Galv. Design, supply and installation as per technical specification. TK-9801A/B, EACH 4 5000 20000.00 B16.9, ASTM A234 Gr.WPB, BW Ends, -, -,As per Ident Code CDBK9H9U
160
As per recent order placed for 4" X 3" CRE S-STD S-STD Concentric reducer, Seamless, ASME
CONC RED. 4'' X 3''
6 EX. ITEM -35 FITTINGS, Size: 4x3 Sch- STD X STD Concentric Reducer, ASTM A105 Galv. Design, supply and installation as per technical specification. TK-9801A/B, EACH 12 6500 78000.00 B16.9, ASTM A234 Gr.WPB, BW Ends, -, Externally PE Tape Coated,As per Ident Code
SCH-STD X STD C4AKTAED
RED. TEE 4'' X 3'' TK-9801A/B,
7 EX. ITEM -36 FITTINGS, Size: 4x3 Sch- STD X STD Reducing Tee, ASTM A105 Galv. Design, supply and installation as per technical specification. EACH 20 11700 234000.00 Weight Basis + Installation
SCH-STD X STD 9803A/B/C, 9806
1/2'' 3000# BSP TK-9801A/B,
8 EX. ITEM -37 FITTINGS, Size: 1/2'' 3000# BSP HALF COUPLING ASTM A105 Galv Design, supply and installation as per technical specification. EACH 320 1000 320000.00 Weight Basis + Installation
HALF COUPLING 9803A/B/C, 9806
As per recent Order placed for 4" BUT 150# Butterfly Valve Wafer Ends, API 609 Cat.A, -, -,
BUTTERFLY TK-9801A/B,
9 EX. ITEM -38 4'' X 150# BUTTERFLY VALVE: Design, supply and installation as per technical specification. EACH 8 18514 148112.00 ASTM A216 Gr.WCB, 150 Lbs, Lug-type FF, Ends as per ASME B16.5, -, Concentric Disc, CS EPDM
VALVE 9803A/B/C, 9806 Coated Disc, Bronze Shaft, -, Packing: EPDM, Seats: EPDM Sleeve,
TK-9801A/B,
10 EX. ITEM -39 REVOLVING HEAD REVOLVING HEAD: 303.11 LPM (3'' FLANGED 150#) EACH 6 8800 52800.00 Based on Budgetary Quotes received from : Newage India, Vimal Fire & AAAGIndia
9803A/B/C, 9806
TK-
11 EX. ITEM -41 4" T-TYPE STRAINER 4 INCH T-TYPE STRAINER EACH 4 229518 918072.00 Man‐Machine‐Material Analysis cost is INR 5,04,693.92
9801A/B
BASIC ₹ 33,01,275.00
SUB TOTAL (A) TOTAL (INCL. GST) ₹ 38,95,504.50
AHR TANK ‐ EXTRA ITEMS ‐ FREE ISSUE BY OTHERS (B&R ADDITIONAL SCOPE IS FABRICATION & INSTALLATION ONLY)
EXTRA ITEM‐CS/SS TEN PROPOSAL
Roof manhole 24” CS Nozzle: Fabrication, erection, and welding of manhole (including cutting. machining, drilling of plate flange and blind flange, The Nozzle Assembly is entirely made from Plate (Plate ‐ IS‐2062 E250Gr B Epoxy coated). The
B&R/61036/HPC gasket cut to suit flange size and hole drilling )as per approved drawing. All activities shall be carried out inside the refinery premises. If any quantity of plate as per Fabrication drawing is 288 kg. Market rate for the plate is ~72 INR/kg.
activity to be executed at Site is carried outside the premises, then the same shall not be charged additionally. Reinforcement pad shall be tested Estimated cost of material for this nozzle is (288 * 72 = 20736 INR). Miscellaneous Cost : Ordering +
1 LTANKAGE/ NOZZLE 600 MM with soap solution by applying pneumatic pressure of 1.05 kg/sq.cm before hydro testing. Contractor to supply all materials including consumables
EACH 2 134173 268346 Overhead + Transportation = 20%.
107 (except Plate Flange, Blind Flange, nozzle neck, RF Pad, gasket, bolt & washer and Hinge items). All handling of materials required for the Total Material Cost = 1.2*20736 = 24883.2 INR. F&I cost shall be : B&R PO cost (Line No.48)
completion of work in accordance with time schedule, are deemed be included in the quoted rates. 159056.0472 (‐)24883.2 = 134172.84
The Nozzle Assembly is entirely made from Plate (Plate ‐ IS‐2062 E250Gr B Epoxy coated). The
Shell manhole 36” CS Nozzle' Fabrication, erection, and welding of manhole (including cutting. machining, drilling of plate flange and blind flange, quantity of plate as per Fabrication drawing is 528 kg. Market rate for the plate is ~72 INR/kg.
B&R/61036/HPC NOZZLE 900 MM gasket cut to suit flange size and hole drilling) as per approved drawing. All activities shall be carried out inside the refinery premises. If any Estimated cost of material for this nozzle is (528 * 72 = 38016 INR). Miscellaneous Cost : Ordering +
activity to be executed at Site is carried outside the premises, then the same shall not be charged additionally. Reinforcement pad shall be tested
2 LTANKAGE/ (SMH401, SMH402 with soap solution by applying pneumatic pressure of 1.05 kg/sq.cm before hydro testing. Contractor to supply all materials including consumables EACH 3 192965 578895 Overhead + Transportation = 20%.
106 & SMH403) (except Plate Flange, Blind Flange, nozzle neck, RF Pad, gasket, bolt & washer and Hinge items). All handling of materials required for the
Total Material Cost = 1.2*38016= 45619.2 INR.
As SOR cost (for S,F&I) is not available, it is interpolated from the 24" Manhole (PO line item 48) ie
completion of work in accordance with time schedule, are deemed be included in the quoted rates.
159056.0472*1.5 =238584.07 INR. F&I cost shall be 238584.07 (‐)45619.2 = 192964.87 INR
The Nozzle Assembly constitutes 0.5m Pipe, 1 No.Flange and 0.6 kg plate . Market rate for the Pipe
Fabrication, Erection, Welding of nozzle of 6 inch diameter with reinforcement pad (RF pad to be cut from plate, rolled to curvature, tell tale hole (PIPE,CS,A106 GR B,SMLS,150MM, Ref.PO : 21000253‐OS‐10120 dt 29‐08‐2021) is 5255.08 INR/m.
drilling and filling with grease after testing), nozzle pipe (to be cut from Pipe to suit nozzle projection), slip on flange (as per ANSI B 16.5) in Market rate for Flange (Supply of 6" FLG 150# SORF, Ref PO: 21000238‐OS‐10120 dt. 03‐09‐2021) is
B&R/61036/HPC accordance with AHR G.A. & nozzle drawing. Reinforcement pad shall be tested with soap solution by applying pneumatic pressure as per AHR 1627.02 INR. Market rate for Plate (Plate ‐ IS‐2062 E250Gr B Epoxy coated) is ~72 INR/kg. Estimated
6" (150 NB) CS
3 LTANKAGE/ drawings before hydrotesting. EACH 4 21332 85328 cost of material for this nozzle is (5255.08 * 0.5 + 1627.02 + 0.6 *72 = 4298 INR). Miscellaneous Cost :
Nozzle Contractor to supply all materials including consumables (except flange, blind flange, nozzle pipe, RF pad, gasket & bolting). All handling of Ordering + Overhead + Transportation = 20%.
133
materials required for the completion of work in accordance with time schedule, NDT, Inspection including inspection agency charges are deemed Total Material Cost = 1.2*4298 = 5157.6 INR. F&I cost shall be : B&R PO cost (Line No.54)
be included in the quoted rates. 26,849.7881(‐)5157.6 = 21332.188 INR
The Nozzle Assembly constitutes 0.6m Pipe, 1 No.Flange and 0.47 kg plate . Market rate for the Pipe
(4" PIP S‐STD Seamless, Pipes, ASME B36.10, ASTM A106 Gr.B Galv. as per ASTM A153, Ref.PO : PO
Fabrication, Erection, Welding of nozzle of 4 inch diameter with reinforcement pad (RF pad to be cut from plate, rolled to curvature, tell tale hole No 22001660‐OQ‐10157 dated 09.01.2023) is 2799.15 INR/m. Market rate for Flange (Supply of 4 IN
drilling and filling with grease after testing), nozzle pipe (to be cut from Pipe to suit nozzle projection), slip on flange (as per ANSI B 16.5) in Lap joint Flange, ASME B16.5, ASTM A105, 150 Lbs, Ref PO: 100136C‐051‐PO‐MM‐1350‐2002C‐00‐
B&R/61036/HPC accordance with AHR G.A. & nozzle drawing. Reinforcement pad shall be tested with soap solution by applying pneumatic pressure as per AHR
4" (100 NB) CS O15100
4 LTANKAGE/ drawings before hydrotesting. EACH 10 16367 163670
Nozzle Contractor to supply all materials including consumables (except flange, blind flange, nozzle pipe, RF pad, gasket & bolting). All handling of
17.09.2022) is 759.5 INR. Market rate for Plate (Plate ‐ IS‐2062 E250Gr B Epoxy coated) is ~72
133 INR/kg. Estimated cost of material for this nozzle is (2799.15 * 0.6 + 759.5 + 0.47 *72 = 2472.83 INR).
materials required for the completion of work in accordance with time schedule, NDT, Inspection including inspection agency charges are deemed
Miscellaneous Cost : Ordering + Overhead + Transportation = 20%.
be included in the quoted rates.
Total Material Cost = 1.2*2472.83 = 2967.396 INR. F&I cost shall be : B&R PO cost (Line No.55)
19,334.4690(‐)2967.396 = 16367.07 INR
The Nozzle Assembly constitutes 0.6m Pipe, 1 No.Flange. Market rate for the Pipe (3" PIP S‐STD
Fabrication, Erection, Welding of nozzle of 3 inch diameter with reinforcement pad (RF pad to be cut from plate, rolled to curvature, tell tale hole Seamless, Pipes, ASME B36.10, ASTM A106 Gr.B Galv. as per ASTM A153, Ref PO No 22001660‐OQ‐
drilling and filling with grease after testing), nozzle pipe (to be cut from Pipe to suit nozzle projection), slip on flange (as per ANSI B 16.5) in
B&R/61036/HPC 10157 dated 09.01.2023) is 2547.25 INR/m. Market rate for Flange (Supply of 3"150# STD WN A105
accordance with AHR G.A. & nozzle drawing. Reinforcement pad shall be tested with soap solution by applying pneumatic pressure as per AHR
3" (80 NB) CS RFBW IBR, Ref PO: 21000238‐OS‐10120) is 789.99 INR. Estimated cost of material for this nozzle is
5 LTANKAGE/ drawings before hydrotesting. EACH 1 12256 12256
Nozzle Contractor to supply all materials including consumables (except flange, nozzle pipe, RF pad, gasket & bolting). All handling of materials required
(2547.25 * 0.6 + 789.9 = 2318.25 INR). Miscellaneous Cost : Ordering + Overhead + Transportation =
133 20%.
for the completion of work in accordance with time schedule, NDT, Inspection including inspection agency charges are deemed be included in the
quoted rates. Total Material Cost = 1.2*2318.25 = 2781.9 INR. F&I cost shall be : B&R PO cost (Line No.56)
15,037.9204(‐)2781.9 = 12256 INR
Page no: 1 of 2
BRIDGE AND ROOF CO. (INDIA) LTD.
SITE FABRICATED TANKS AT 2G ETHANOL BIO-REFINERY PROJECT, HPCL, BATHINDA (PUNJAB)
The Nozzle Assembly constitutes 0.6m Pipe, 1 No.Flange. Market rate for the Pipe (1" PIP S‐XS
Seamless, Pipes, ASME B36.10, ASTM A106 Gr.B Galv. as per ASTM A153, Ref PO No 22001660‐OQ‐
10157 dated 09.01.2023) is 762.71 INR/m. Market rate for Flange (Supply of 1"150# XS WN RFBW
Fabrication, Erection, Welding of nozzle of 1 inch diameter, nozzle pipe (to be cut from Pipe to suit nozzle projection), slip on flange (as per ANSI B A105, Ref PO: 21000238‐OS‐10120 dt 03‐09‐2021) is 228.848 INR. Estimated cost of material for this
B&R/61036/HPC 16.5) and welding of Stiffeners in accordance with AHR G.A. & nozzle drawing.
1" (150 NB) CS nozzle is (762.71 * 0.6 + 228.848 = 686.474 INR). Miscellaneous Cost : Ordering + Overhead +
7 LTANKAGE/ Contractor to supply all materials including consumables (except flange, nozzle pipe, gasket & bolting). All handling of materials required for the EACH 3 4548.13 13644.39
Nozzle completion of work in accordance with time schedule, NDT, Inspection including inspection agency charges are deemed be included in the quoted
Transportation = 20%.
133 Total Material Cost = 1.2*686.474= 823.7688 INR.
rates.
As SOR cost (for S,F&I) is not available, it is interpolated from the 1.5" Nozzle ie 8057.8493/1.5 =
5371.899 INR. F&I cost shall be 5371.899 (‐)823.7688 = 4548.13 INR
BASIC 11,28,974.39
SUB TOTAL (B) TOTAL (INCL. GST) 13,32,189.78
Page no: 2 of 2
BRIDGE & ROOF CO. (I) LTD.
EXTRA ITEM NO - 12
SITE FABRICATED TANKS"AT 2G ETHANOL BIO-REFINERY PROJECT, HPCL, BATHINDA
1. NAME OF WORK :
(PUNJAB)/PO. NO.-21000265-OQ-10120 DATE-01.09.2021
2. NAME OF CONTRACTOR: BRIDGE AND ROOF COMPANY(INDIA) LIMITED
3. PO NO. : PO. NO.-21000265-OQ-10120 DATE-01.09.2021
ANALYSIS OF RATE FOR 3/4 INCH NOZZLE CS
DESCRIPTION => SUPPLY, FABRICATION, ERECTION AND WELDING OF 3/4 INCH DIAMETER NOZZLE AS PER API 650 WITH SEAMLESS PIPES/ PLATE FABRICATED PIPE, SLIP ON
FLANGES WITH DRILLED HOLES AS PER ANSI-B-16.5, GASKETS, NUT, BOLTS, WASHER . CONTRACTOR TO SUPPLY ALL MATERIALS REQUIRED FOR THE NOZZLES)
CONSIDERING ONE NO 3/4'' CS NOZZLE (REFER DOC. NO: 201565C-101-SR-2520-0001-A1109-148_2 (BR-61036-339) TK-1101A/B)
A) DESIGN AND DETAIL DRAWING COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
1.00 COST FOR DESIGN AND DETAIL DRAWING OF NOZZLE LS 1.000 500.00 500.00
SUBTOTAL (A)= 500.00
B) FINISHED RAW MATERIALS COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
1.00 MATERIAL COST FOR PIPE (3/4'' SMLS SCH. 160 A-106 GR-B) MTR 0.151 790.25 119.33 OFFER ENCLOSED (M/S MAHALAKSHMI)
2.00 MATERIAL COST FOR FLANGE (3/4 ''X 150# SORF A105) NO 1.000 192.64 192.64 OFFER ENCLOSED (M/S M.S.FITTINGS)
4.00 MATERIAL COST FOR GASKET (3/4'' X 150# NACF) MT 1.000 9.07 9.07 OFFER ENCLOSED (M/S J.K ENGINEERS)
....................................... .......................................
Sign of B and R Page No-1 of 1 Sign of TEN
201565C-101-SR-2520-0001-A1109-148_2 (BR-61036-339)
BILL OF MATERIALS
NOS
ITEM. LENGTH IN WIDTH IN THK. IN . UNIT DRG WT IN
MKD. NO ITEM DESCRIPTION MATERIAL SPECN REMARKS
NO METRE METRE MM REQ WEIGHT M.T.
D
N11 51 PLATE 0.141 0.050 6 2 7.85 0.001 IS 2062 E250 GR.BR stiffner
54 3/4'' NB.(SCH.160) PIPE 0.153 1 A-106 GR-B pipe
55 3/4''X 150# SORF FLG 1 A-105 FLANGE
TOTAL 0.001
J.K. ENGINEERS
SL NO ITEM DESCRIPTION QTY(NO) COST
M12 X 55 MM LEN. STUD BOLTS WITH NUT AND
1 18
1 WASHER A193 GR.B7 / A194 GR.2H
2 PACKING CHARGE@4% 0.72
3 FREIGHT CHARGE@5% 0.9
4 TRANSIT INSURANCE CHARGE@1% 0.18
5 TPI CHARGE@2% 0.36
TOTAL 20.16
J.K. ENGINEERS
SL NO ITEM DESCRIPTION QTY(NO) COST
3/4 IN 3MM THK NON ASBESTOS COMPRESSED
1 8.1
1 FIBRE GASKET
2 PACKING CHARGE@4% 0.324
3 FREIGHT CHARGE@5% 0.405
4 TRANSIT INSURANCE CHARGE@1% 0.081
5 TPI CHARGE@2% 0.162
TOTAL 9.072
BRIDGE & ROOF CO. (I) LTD.
EXTRA ITEM NO - 13
CONSIDERING ONE NO 1'' CS NOZZLE (REFER DOC. NO: 201565C-101-SR-2520-0001-A1109-167_1 (BR-61036-394) (TK-1801A/B)
A) DESIGN AND DETAIL DRAWING COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
1.00 COST FOR DESIGN AND DETAIL DRAWING OF NOZZLE LS 1.000 500.00 500.00
SUBTOTAL (A)= 500.00
B) FINISHED RAW MATERIALS COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
1.00 MATERIAL COST FOR PIPE (1'' SMLS SCH. 160 A-106 GR-B) MTR 0.200 926.50 185.30 OFFER ENCLOSED (M/S MAHALAKSHMI)
2.00 MATERIAL COST FOR FLANGE (1'' X 150# SORF A105) NOS 1.000 278.88 278.88 OFFER ENCLOSED (M/S M.S.FITTINGS)
4.00 MATERIAL COST FOR GASKET (1' X 150# NACF) MT 1.000 9.07 9.07 OFFER ENCLOSED (M/S J.K ENGINEERS)
....................................... .......................................
Sign of B and R Page No-1 of 1 Sign of TEN
201565C-101-SR-2520-0001-A1109-167_1 (BR-61036-394) (TK-1801A/B)
BILL OF MATERIALS
NOS
ITEM. LENGTH IN WIDTH IN THK. IN . UNIT DRG WT IN
MKD. NO ITEM DESCRIPTION MATERIAL SPECN REMARKS
NO METRE METRE MM REQ WEIGHT M.T.
D
11 1'' NB.(SCH.160) PIPE 0.200 1 A-106 GR-B pipe
LT2 12 1''X 150# SORF FLG 1 A-105 FLANGE
13 PLATE 0.141 0.050 6 2 7.85 0.001 IS 2062 E250 GR.BR stiffner
TOTAL 0.001
J.K. ENGINEERS
SL NO ITEM DESCRIPTION QTY(NO) COST
M12 X 55 MM LEN. STUD BOLTS WITH NUT AND
1 18
1 WASHER A193 GR.B7 / A194 GR.2H
2 PACKING CHARGE@4% 0.72
3 FREIGHT CHARGE@5% 0.9
4 TRANSIT INSURANCE CHARGE@1% 0.18
5 TPI CHARGE@2% 0.36
TOTAL 20.16
J.K. ENGINEERS
SL NO ITEM DESCRIPTION QTY(NO) COST
3/4 IN 3MM THK NON ASBESTOS COMPRESSED
1 8.1
1 FIBRE GASKET
2 PACKING CHARGE@4% 0.324
3 FREIGHT CHARGE@5% 0.405
4 TRANSIT INSURANCE CHARGE@1% 0.081
5 TPI CHARGE@2% 0.162
TOTAL 9.072
BRIDGE & ROOF CO. (I) LTD.
EXTRA ITEM NO - 15
SITE FABRICATED TANKS"AT 2G ETHANOL BIO-REFINERY PROJECT, HPCL, BATHINDA
1. NAME OF WORK :
(PUNJAB)/PO. NO.-21000265-OQ-10120 DATE-01.09.2021
2. NAME OF CONTRACTOR: BRIDGE AND ROOF COMPANY(INDIA) LIMITED
3. PO NO. : PO. NO.-21000265-OQ-10120 DATE-01.09.2021
ANALYSIS OF RATE FOR 20 INCH NOZZLE CS
DESCRIPTION => SUPPLY, FABRICATION, ERECTION AND WELDING OF 20 INCH DIAMETER NOZZLE AS PER API 650 WITH SEAMLESS PIPES/ PLATE FABRICATED PIPE, SLIP
ON FLANGES WITH DRILLED HOLES AS PER ANSI-B-16.5, GASKETS, NUT, BOLTS, WASHER . CONTRACTOR TO SUPPLY ALL MATERIALS REQUIRED FOR THE NOZZLE.
CONSIDERING ONE NO 20'' CS NOZZLE (REFER DOC. NO: 201565C-101-SR-2520-0001-A1109-049_1 (BR-61036-124) TK-9721
A) DESIGN AND DETAIL DRAWING COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
1.00 COST FOR DESIGN AND DETAIL DRAWING OF NOZZLE LS 1.000 1,000.00 1,000.00
SUBTOTAL (A)= 1,000.00
B) FINISHED RAW MATERIALS COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
1.00 MATERIAL COST FOR RF PAD PLATE AND NECK NOZZLE MT 0.232 71,700.00 16,653.72 PO ENCLOSED (M/S G.K. ISPAT PVT. LTD)
2.00 MATERIAL COST FOR FLANGE (20 ''X 150# SORF A105) NO 1.000 17,183.04 17,183.04 OFFER ENCLOSED (M/S M.S.FITTINGS)
4.00 MATERIAL COST FOR GASKET (20'' X 150# NACF) MT 1.000 378.00 378.00 OFFER ENCLOSED (M/S J.K ENGINEERS)
SUBTOTAL (B)= 37,776.36
C) EXECUTION COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
1.00 FIT UP, ALIGNMENT AND WELDING COST ID 113.25 650.00 73,612.50 RATE TAKEN FROM OUR OTHER ON
2.00 ERECTION COST IM 23.71 200.00 4,741.35 GOING JOB (BID NO.RJ/B018-930-PK-
TN-3010/1040) (ENCLOSED)
3.00 DYE PENETRANT TEST CHARGES INCH 420.03 30.00 12,601.00
RADIOGRAPHY CHARGES OF NOZZLE NECK RING (FILM
4.00 SIZE : 4'' X 15'') EACH 1.00 450.00 450.00 RATE OF OUR SUB CONTRACTOR
....................................... .......................................
Sign of B and R Page No-1 of 1 Sign of TEN
201565C-101-SR-2520-0001-A1109-049_1 (BR-61036-124) TK-9721
BILL OF MATERIALS
J.K. ENGINEERS
SL NO ITEM DESCRIPTION QTY(NO) COST
M27 X 120 MM LEN. STUD BOLTS WITH NUT AND
1 159
1 WASHER A193 GR.B7 / A194 GR.2H
2 PACKING CHARGE@4% 6.36
3 FREIGHT CHARGE@5% 7.95
4 TRANSIT INSURANCE CHARGE@1% 1.59
5 TPI CHARGE@2% 3.18
TOTAL 178.08
J.K. ENGINEERS
SL NO ITEM DESCRIPTION QTY(NO) COST
20 INCH 150# RING GASKET NON ASBESTOS
1 337.5
1 COMPRESSED FIBRE
2 PACKING CHARGE@4% 13.5
3 FREIGHT CHARGE@5% 16.875
4 TRANSIT INSURANCE CHARGE@1% 3.375
5 TPI CHARGE@2% 6.75
TOTAL 378
BRIDGE & ROOF CO. (I) LTD.
EXTRA ITEM NO - 19
SITE FABRICATED TANKS"AT 2G ETHANOL BIO-REFINERY PROJECT, HPCL,
1. NAME OF WORK :
BATHINDA (PUNJAB)/PO. NO.-21000265-OQ-10120 DATE-01.09.2021
2. NAME OF CONTRACTOR: BRIDGE AND ROOF COMPANY(INDIA) LIMITED
3. PO NO. : PO. NO.-21000265-OQ-10120 DATE-01.09.2021
ANALYSIS OF RATE FOR 20 INCH TANK UNDER BOTTOM CONNECTION CS
DESCRIPTION => SUPPLY, FABRICATION, ERECTION AND WELDING OF 20 INCH TANK UNDER BOTTOM CONNECTION AS PER API 650 WITH SEAMLESS PIPES/
PLATE FABRICATED PIPE, SLIP ON FLANGES WITH DRILLED HOLES AS PER ANSI-B-16.5, GASKETS, NUT, BOLTS, WASHER . CONTRACTOR TO SUPPLY ALL
MATERIALS REQUIRED FOR THE NOZZLES)
CONSIDERING ONE NO 20" CS TANK UNDER-BOTTOM CONNECTION (REFER DOC. NO: 201565C-101-SR-2520-0001-A2401-014_3 (BR-61036-C-122)
(TK-9721)
A) DESIGN AND DETAIL DRAWING COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
COST FOR DESIGN AND DETAIL DRAWING OF 20" CS TANK
1.00 LS 1.000 1,000.00 1,000.00
UNDER-BOTTOM CONNECTION
SUBTOTAL (A)= 1,000.00
B) FINISHED RAW MATERIALS COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
PO ENCLOSED (M/S G.K. ISPAT PVT.
1.00 MATERIAL COST FOR PIPE (20'' PIPE THK-18MM ) MTR 0.498 71,700.00 35,706.60
LTD)
2.00 MATERIAL COST FOR FLANGE (20''X 150# SORF A-105) NO 1.000 17,183.00 17,183.00 OFFER ENCLOSED (M/S M.S.FITTINGS)
3.00 MATERIAL COST FOR ELBOW (20''X 90 DEG S/R THK-18MM) NO 1.000 3,80,298.00 3,80,298.00 OFFER ENCLOSED ((M/S GIPL)
SUBTOTAL (B)= 4,33,187.60
C) EXECUTION COST
S.NO DESCRIPTION UOM QTY RATE (RS) AMOUNT IN RS. REMARKS
1.00 FIT UP, ALIGNMENT AND WELDING COST ID 140.00 650.00 91,000.00 RATE TAKEN FROM OUR OTHER ON
GOING JOB (BID NO.RJ/B018-930-PK-TN-
2.00 ERECTION COST IM 48.120 200.00 9,624.00 3010/1040) (ENCLOSED)
RADIOGRAPHY CHARGES OF NOZZLE NECK RING (FILM SIZE
3.00 EACH 1.000 450.00 450.00 RATE OF OUR SUB CONTRACTOR
: 4'' X 15'')
PNEUMATIC TESTING OF RF PAD CHARGE @ Rs. 20 PER INCH
4.00 LS 1.000 400.00 400.00
DIA
SUBTOTAL (D)= 1,01,474.00
D) PAINTING COST
LENGTH IN DRG WT IN
MKD. NO ITEM. NO ITEM DESCRIPTION WIDTH IN METRE NOS. REQD REMARKS
METRE M.T.
2 PLATE-18MM THK 1.596 0.5 1 0.155 FOR PIPE
3 20'' X 90 DEG S/R SCH-80 1 A234 GR-WPB
4 PLATE-18MM THK 1.596 1.52 1 0.343 FOR PIPE
N3
5 20''X 150# SORF FLG 1 A-105
6 GASKET 0.127 OD X 0.092 ID X 1.5 MM THK 1 SPRIAL WOUND SS304
8 M27 BOLTS WITH NUT & WASHER 0.070 4 A193 GR.B7 & A194 GR.2H
PAINTING AREA
PIPE SIZE LENGTH (MTR) DIA (MTR) CIR (MTR) AREA SQ. MTR
20'' PIPE 2.02 0.508 1.60 3.22
MATERIAL COST
M.S.FITTINGS MFG CO. PVT. LTD
fyi
With regards,
PREMKUMAR NAIR
SR. MANAGER - MARKETING
09429623602
Email: info@aaagindia.in
Shah Bhogilal
Jethalal & Bros.
-----------------------------------------------------------------------------------------------------------------------------------------
72, Siddhi Vinayak Estate, Opp. Ramdev Kitchen Express, Nr. Shah Alloys Cross Road, Santej – Vadsar Road,
Village : Santej-382721, Tal : Kalol, Dist. Gandhinagar, Tel.No-02764-268612 /13/ 14 / 15
Web : www.aaagindia.in
----------------------------------------------------------------------------------------------------------------------------------------------------
1
M arketing /Enquiry :info@ aaagindia.in
TechnicalSupport :technical@ aaagindia.in (7574870666/658)
Quality Control/TPI :technical@ aaagindia.in (7574870668)
AccountSupport :accounts@ aaagindia.in (7574870679)
Dispatch Support :dispatch@ aaagindia.in (7574870655/659)
Service Support :support@ aaagindia.in (7574870669/670)
SBJ/2022-23/ 14139P(Rev.01)
21st February, 2023
Dear Sir,
We take the reference of your above referred enquiry, for supply of FIRE FIGHTING EQUIPMENTS; accordingly, we are herewith giving our very best and
competitive rate of your kind acceptance. The details are as under: -
SR.NO. DESCRIPTIONS QTY. PRICE
(RS)/EACH
01.00 Supply of “AAAG” make REVOLVING HEAD 06 8,800.00
NOZZLE) suitable to discharge 303LPM made of Nos.
GUN METAL (LTB-2) as per IS: 906 with 80NB
flanged inlet
'TERMS & CONDITIONS
01.00 PRICES FOR- AT OUR WORKS AT AHMEDABAD, GUJARAT
02.00 GST @18% APPLICABLE
03.00 DELIVERY OF Ready Stock on approval of technical documents
EQUIPMENTS
04.00 PAYMENT 100% payment AGAINST PERFORMA INVOICE/ LC
ONLY
2
05.00 VALIDITY Acceptable as per Tender details
06.00 IN-HOUSE Pre-inspection will be at our works at Ahmedabad
INSPECTION
07.00 TP INSPECTION At our works- The necessary charges are extra
applicable.
08.00 FREIGHT Extra applicable
09.00 P&F Extra applicable (Wooden Crate charges are extra
applicable)
10.00 PAINTING As per IS: 5, Shade No: 536/ NOT APPLICABLE
We hope you will find our above offer as most competitive to enable us to receive your valuable order at the earliest
With regards,
PREMKUMAR NAIR
SR. MANAGER - MARKETING
09429623602
Email: info@aaagindia.in
Shah Bhogilal
Jethalal & Bros.
-----------------------------------------------------------------------------------------------------------------------------------------
72, Siddhi Vinayak Estate, Opp. Ramdev Kitchen Express, Nr. Shah Alloys Cross Road, Santej – Vadsar Road,
Village : Santej-382721, Tal : Kalol, Dist. Gandhinagar, Tel.No-02764-268612 /13/ 14 / 15
Web : www.aaagindia.in
----------------------------------------------------------------------------------------------------------------------------------------------------
M arketing /Enquiry :info@ aaagindia.in
TechnicalSupport :technical@ aaagindia.in (7574870666/658)
Quality Control/TPI :technical@ aaagindia.in (7574870668)
AccountSupport :accounts@ aaagindia.in (7574870679)
Dispatch Support :dispatch@ aaagindia.in (7574870655/659)
Service Support :support@ aaagindia.in (7574870669/670)
Dear Sir,
Please confirm whether provided item comply with below marked material or if not revise quote accordingly and resubmit.
Thanks
Shrikant Falke
4
Dear Sir,
We take the reference of your above referred enquiry, for supply of FIRE FIGHTING EQUIPMENTS; accordingly, we are herewith giving our very best and
competitive rate of your kind acceptance. The details are as under: -
SR.NO. DESCRIPTIONS QTY. PRICE
(RS)/EACH
01.00 Supply of “AAAG” make REVOLVING HEAD 06 7,800.00
NOZZLE) suitable to discharge 303LPM made of Nos.
SS-304 as per IS: 906 with 80NB flanged inlet
'TERMS & CONDITIONS
01.00 PRICES FOR- AT OUR WORKS AT AHMEDABAD, GUJARAT
02.00 GST @18% APPLICABLE
03.00 DELIVERY OF Ready Stock on approval of technical documents
EQUIPMENTS
04.00 PAYMENT 100% payment AGAINST PERFORMA INVOICE/ LC
ONLY
05.00 VALIDITY Acceptable as per Tender details
06.00 IN-HOUSE Pre-inspection will be at our works at Ahmedabad
INSPECTION
07.00 TP INSPECTION At our works- The necessary charges are extra
applicable.
08.00 FREIGHT Extra applicable
09.00 P&F Extra applicable (Wooden Crate charges are extra
applicable)
10.00 PAINTING As per IS: 5, Shade No: 536/ NOT APPLICABLE
We hope you will find our above offer as most competitive to enable us to receive your valuable order at the earliest
With regards,
PREMKUMAR NAIR
SR. MANAGER - MARKETING
09429623602
Email: info@aaagindia.in
Shah Bhogilal
5
Jethalal & Bros.
-----------------------------------------------------------------------------------------------------------------------------------------
72, Siddhi Vinayak Estate, Opp. Ramdev Kitchen Express, Nr. Shah Alloys Cross Road, Santej – Vadsar Road,
Village : Santej-382721, Tal : Kalol, Dist. Gandhinagar, Tel.No-02764-268612 /13/ 14 / 15
Web : www.aaagindia.in
----------------------------------------------------------------------------------------------------------------------------------------------------
M arketing /Enquiry :info@ aaagindia.in
TechnicalSupport :technical@ aaagindia.in (7574870666/658)
Quality Control/TPI :technical@ aaagindia.in (7574870668)
AccountSupport :accounts@ aaagindia.in (7574870679)
Dispatch Support :dispatch@ aaagindia.in (7574870655/659)
Service Support :support@ aaagindia.in (7574870669/670)
Dear sir/madam,
We have requirement for revolving head nozzle as 303.11 LPM (3'' FLANGED 150#) for HPCL Bathinda 2G ethanol project.
Please provide us budgetary prices for 6 no of nozzle.
Thanks
Shrikant Falke
-----------------------------------------------
Shah Bhogilal Jethalal & Bros, Ahmedabad, India
6
-----------------------------------------------
Shah Bhogilal Jethalal & Bros, Ahmedabad, India
-----------------------------------------------
Shah Bhogilal Jethalal & Bros, Ahmedabad, India
7
Ruchi Bhandarkar
Quotation # YR220223
To
Shrikant Falke
m/s TECHNIPENERGIES INDIA LTD.
Technology Centre – 2, B Wing,
Prima Bay Gate No. 5, Saki Vihar Road,
Powai 400 072 - Mumbai, Maharashtra
Ph. 91-022-6700-2043
shrikant.falke@technipenergies.com
Dear sir/madam,
This has reference to your subject RFQ/Enquiry, we are pleased to quote as under for the scope of supply only (any Civil work, Massonary, Erection,
Installation, Commissioning, Testing, Demonstration at site is EXCLUDED from scope of supply/work) :
1
SR. QTY UNIT PRICE
ITEMS GST
NO. (NO.) (INR)
1. REVOLVING HEAD, made of Gunmetal, 6 9,800/- 18%
- 3” NB MS-flange inlet drilled to ANSI B 16.5 # 150 SOFF,
- Suitable for 400 LPM discharge capacity,
- generally conf. to IS:906.
- Typical sketch for general idea :
TERMS-CONDITIONS :
1. PRICE BASIS Ex works Surendranagar (Gujarat) - Transportation, Transit Insurance, Unloading of material at site to be arranged and
born by the buyer itself.
2. GST Extra as quoted above, subject to statutory-change if any at the time of supply.
3. INSPECTION Material shall be supplied with Internal Test Certificate.
- If required by TPIA - charges shall be Extra as applicable (Lump sum Rs. 13,800/callup + GST 18% may be
considered).
- For any special Test requirement i.e. NDT (RT, DP), IGC test, Meeasuring Vertical flow etc. will cost extra as
applicable, to be specified if required.
4. DELIVERY Within 7 weeks/subject to actual Quantity, after receipt of Manufacturing Clearance with approved Drawing, Datasheet &
QAP (shall be submitted within 10 working days by vendor) followed by the firm-order.
5. PAYMENT 100% with taxes within 7 days of receipt of material.
6. WARRANTY 12 months from date of receipt of material against any manufacturing/workmanship defect.
7. OFFER VALIDITY 30 days.
Our,
GST : 24AABCN5691G1ZF PAN : AABCN5691G
2
Kinldy download our Product-Catalogue from link : NewAge Product Catalogue
SPECIAL REMARKs :
i. W.e.f. 01.10.2020, as per the Finance Act, 2020 and the Section 206C(1H) of Income Tax Act, 1961, we shall charge TCS @ 0.1% on our sales
consideration exceeding Rs. 50,00,000/- in current year.
Hope, offer above shall be found satisfactory. Kindly acknowledge upon receipt and advise us the feedback, we are looking forward to be favoured with
your valued Purchase Order.
Thanking and assuring you of our best business services and prompt attention at all times, we sincerely remain.
Dear sir/madam,
We have requirement for revolving head nozzle as 303.11 LPM (3'' FLANGED 150#) for HPCL Bathinda 2G ethanol project.
Please provide us budgetary prices for 6 no of nozzle.
Thanks
Shrikant Falke
3
VIMAL FIRE CONTROLS PVT. LTD.
CIN: U29193MH1996PTC104191
Dear Sir,
We acknowledge with thanks the receipt of your above mentioned enquiry. We in this connection have
the pleasure to submit our most competitive offer.
Before we submit our quotation, we wish to inform you, we are an ISO 9001:2015, ISO 14001:2015 &
ISO 45001:2018 Certified Company registered with SSI, NSIC and EIL having diversified activities
in the fields of Fire, Safety, Security, Surveillance, Environment Protection, Pollution Control and
Rescue. For more than 40 years we have been serving to the needs of the Indian Industry and today, we
are in the forefront among the fire and safety equipment and systems manufacturers in India, offering
QUOTATION
our clients versatile and highly advanced equipment’s and custom designed specialty fire protection
systems. Our High Volume Long Range Monitors, Remote Controlled Monitors, Multi Purpose
Fire Fighting Vehicles, and Auto Detection and Extinguishing systems, which are introduced by
us for the first time in India as import substitute, enjoys a distinct reputation and the same are
admired by the users for its quality excellence, durability, effectiveness and trouble free operation.
For our successful R&D efforts, we have been presented the “National Award” by the Vice
President of India. Almost all Government Organizations of Oil and Gas Sector, Petrochemical,
Fertilizer, Port Trusts, Power Plants, Aviation Industry and Defense establishments are our valued
clients. With our dedicated development activities, we would like to be a dependable solution provider
to our clients by offering the most versatile equipment’s, systems and appropriate timely services.
We have studied your requirements and every endeavor has been made to offer you the product/
products, which shall meet or exceed to your requirements. Also every effort has been made to keep our
prices most reasonable.
HO: 19/20, Vardhman Complex, Off L B S Marg, Behind Punjab & Sindh Bank, Vikhroli-West, Mumbai-400083, India
Phone: +91 22 25783335/6/7 | Fax: +91 22 25783338 | e-Mail: vfcplmumbai@vimalfire.com | www.vimalfire.com
1
VIMAL FIRE CONTROLS PVT. LTD.
CIN: U29193MH1996PTC104191
QUOTATION
Guarantee : 12 months from the date of receipt of material at site.
Cancellation/ : Orders once placed and accepted can be cancelled / amended only
Amendment of PO with our consent and compensation shall be paid by client.
Cancellation of items of special sizes manufactured will not be
accepted without full compensation to us for all expenses incurred
after receipt of such orders in production.
We now look forward with interest receiving your valued order for our prompt execution.
In case of any further information or clarification is required please let us know, we would be
immensely glad to provide such information on hearing from you.
Thanking you and assuring you innovative product support and quality services in the field of Fire &
Safety, we remain,
Yours faithfully,
HO: 19/20, Vardhman Complex, Off L B S Marg, Behind Punjab & Sindh Bank, Vikhroli-West, Mumbai-400083, India
Phone: +91 22 25783335/6/7 | Fax: +91 22 25783338 | e-Mail: vfcplmumbai@vimalfire.com | www.vimalfire.com
2
Vimal Fire Controls
Private Limited
ONE STOP GATEWAY FOR ALL YOUR FIRE, SAFETY, SECURITY & SURVEILLANCE NEEDS
An ISO 9001:2015, 14001:2015, 14001:2018 certified company, Vimal Fire Controls Pvt. Ltd. is pioneer in the field
of Fire-Fighting Engineering since 1983. We offer an exhaustive range of SHOOTFIRE brand innovative and
cutting-edge technology products under our portfolio of Fire Safety, Security and Surveillance. These products
are certified by global bodies like UL/FM/VdS/ISI/CE/LPCB, etc. Our Solutions & Services have proved its
worthiness in controlling many massive fires in India and Abroad. Few of our products are as mentioned below:
QUOTATION
India’s First PLC based Transformer Fire World’s Smartest VdS (Germany) Approved Addressable Line Type Heat Detection
Artificial Intelligence Based Smart Protection System using World-Class
Surveillance Analytics including System capable of pin pointing the exact location of Rise in Temp. / Fire. It is Site
UL, FM, VdS, Approved Detection,
Fire Detection, Face Grabber Configurable. Temperature Detection Range: -400C to +2000C.
with Internal & External
Counter etc. Applications: Rail/Road Tunnels, Cable Galleries, Conveyor Belts, Warehouse & other
Suppression
inaccessible areas etc.
IS:15683
CM/L-7200137299
PORTABLE FIRE
EXTINGUISHER
India’s first ISI Marked seamless, Rim Seal Fire Protection System
for Floating Roof Storage Tanks UL, FM, VdS Listed Aspirating Smoke Detection System. 5 times faster &
light-weight Aluminium Fire Ext-
-inguisher of all types. Also, containing Petroleum accurate than point detectors
available ISI Marked Products worth $100 Applications: Railway Coaches, Deep-Freeze Warehouses, Large Data Centres,
MS Fire Ext. Billion USD Museums, Large Halls, Laboratories, IT Racks, Telecommunications Facilities etc.
Clean Agent NOVEC 1230/FM 200 Proven Emergency Response Service UL, FM Approved Sensing / Water/Foam/DCP/Multi-Purpose
/IG-541/IG-55/C02 - UL/FM/VdS by Chartered Air Flights for Fire Pneumatic Tube Based Fire Firefighting Tender/Vehicles, Fire
/LPCB Approved Fire Emergencies & Disasters in Detection & Protection for Jeep, Ambulance, Trailer Fire
Suppression System India & Abroad Electrical Panels etc. Pump etc.
EXTRA ITEM NO - 41
SITE FABRICATED TANKS"AT 2G ETHANOL BIO-REFINERY PROJECT, HPCL, BATHINDA (PUNJAB)/PO. NO.-
1. NAME OF WORK :
21000265-OQ-10120 DATE-01.09.2021
2. NAME OF CONTRACTOR: BRIDGE AND ROOF COMPANY(INDIA) LIMITED
3. PO NO. : PO. NO.-21000265-OQ-10120 DATE-01.09.2021
ANALYSIS OF RATE FOR 4 INCH 150# Y-TYPE STRAINER
DESCRIPTION => DESIGN, SUPPLY AND INSTALLATION OF 4" Y-TYPE STRAINER RATING 150 FLANGED ENDS, MNF STD, ASTM A216 GR.WCB GALV. WITH GASKET, NUTS AND BOLTS.
SUPPLY AND INSTALLATION AS REQUIREDE
CONSIDERING ONE NO 4" Y-TYPE STRAINER RATING 150 FLANGED ENDS (REFER DOC. NO: 201565C-101-SR-2520-0001-A1109-202_1 (BR/61036/217 P&ID) (TK-
9801A/B)
1.00 COST FOR DESIGN AND DETAIL DRAWING OF 4" Y-TYPE STRAINER LS 1.000 1,000.00 1,000.00
1.00 MATERIAL COST FOR 4 INCH Y-TYPE STRAINER (4''X150# ) NO 1.000 4,50,000.00 4,50,000.00 OFFER ENCLOSED (M/S GRAND PRIX)
MATERIAL COST FOR STUD BOLT WITH NUT AND WASHER (M16 X
2.00 NOS 16.00 38.08 609.28 OFFER ENCLOSED (M/S J.K ENGINEERS)
70 MM LENGTH A193GR.B7/A194 GR.2H)
3.00 MATERIAL COST FOR GASKET (4'' X 150# NACF) NO 2.00 42.34 84.67 OFFER ENCLOSED (M/S J.K ENGINEERS)
-------------------------------- ----------------------------------
Sign of B and R Page No- 1 of 1 Sign of TEN
MATERIAL COST
J.K. ENGINEERS
J.K. ENGINEERS
SL NO ITEM DESCRIPTION QTY(NO) COST
1 4 INCH 150# NACF 1 37.80
2 PACKING CHARGE@4% 1.51
3 FREIGHT CHARGE@5% 1.89
4 TRANSIT INSURANCE CHARGE@1% 0.38
5 TPI CHARGE@2% 0.76
TOTAL 42.34
BRIDGE AND ROOF CO. (INDIA) LTD.
SITE FABRICATED TANKS AT 2G ETHANOL BIO-REFINERY PROJECT, HPCL, BATHINDA (PUNJAB)
ANNEXURE-02 REASONS FOR ADDITION OF
NEW ITEMS
EXTRA ITEMS ‐ B&R ADDITIONAL SCOPE IS SUPPLY , FABRICATION & INSTALLATION
EXTRA ITEM‐CS/SS
SL EXTRA ITEM
TYPE DESCRIPTION OF ITEMS TANK NO. UOM PROPOSED QTY TYPE OF NOZZLES / SERVICE REASON FOR ADDITION / CHANGE
NO NO
3/4" CS Nozzle - Supply, fabrication, erection and welding of nozzle of 3/4 inch diameter with reinforcement pad plate, seamless pipes/ plate 1. TK-1101 A / B,
At time of SOQ preparation size of this nozzle was
fabricated pipe, slip on flanges with drilled holes as per ANSI-B-16.5, gaskets, nut, bolts, washer, including Spares trough including installation as 2. TK-1102 A / B,
1 EX. ITEM -12 3/4'' CS NOZZLE per specification. Reinforcement pad shall be tested with soap solution by applying pneumatic pressure of 1.05 kg/sq.cm before hydro testing.
NOS 16 Float and Tape Level Gauge. hold., with note Level gauge nozzle size will be
3. TK-1401 A / B,
Contractor to supply all materials required for the nozzles. confirmed after finalization of instrument vendor.
4. TK-1801 A / B
1" CS Nozzle - Supply, fabrication, erection and welding of nozzle of 1 inch diameter with reinforcement pad plate, seamless pipes/ plate fabricated
pipe, slip on flanges with drilled holes as per ANSI-B-16.5, gaskets, nut, bolts, washer, including Spares trough including installation as per At time of SOQ preparation size of these nozzle was
2 EX. ITEM -13 1'' CS NOZZLE specification. Reinforcement pad shall be tested with soap solution by applying pneumatic pressure of 1.05 kg/sq.cm before hydro testing.
TK-1801 A / B NOS 4 Level Transmitter
hold. With note By instrument Department.
Contractor to supply all materials required for the nozzles.
BUTTERFLY TK-9801A/B,
9 EX. ITEM -38 4'' X 150# BUTTERFLY VALVE: Design, supply and installation as per technical specification. EACH 8 Foam /Fire water System This item is added during Detail Engineering
VALVE 9803A/B/C, 9806
TK-9801A/B,
10 EX. ITEM -39 REVOLVING HEAD REVOLVING HEAD: 303.11 LPM (3'' FLANGED 150#) EACH 6 Foam /Fire water System This item is added during Detail Engineering
9803A/B/C, 9806
Page no: 1 of 1
ANNEXURE-02 (REASONS FOR ADDITION OF NEW ITEMS)
AHR tank (R-9781) is a part of the PCTP Package supplied by LARS Enviro. The material supply for the
tank is by LARS. Fabrication and Installation of AHR tank is included in the scope of Bridge and Roof
(B & R).
1) Following Tender SOQ are already included in the tender for AHR Tank:
a. Fabrication of Bottom plates & Annular plates in IS2062 for the tank (R-9781)
b. Fabrication of shell & wind girder Shell strakes in IS 2062 for the tank (R-9781)
c. Fabrication of Tank Roof Fabrication in IS2062 for the tank (R-9781)
d. Installation of Internals for Anaerobic Reactor (R-9781)
e. Tank Bottom Testing for R-9781 #:
f. Tank Shell Testing for R-9781 #:
g. Tank Roof Testing for R-9781 # :
h. Tank Calibration for R-9781 #:
2) There is no separate line item for the Fabrication and Installation (F & I) of the nozzles and has to be
considered as additional line item in the tender SOQ. These were missed to be included in the B&R
Tender due to nonavailability of the AHR tank details and quantities (both the tenders were being
issued during Mar’21 to June’21) and when the PCTP order was placed, the bids for Site Fabricated
Tanks were already under evaluation and there was no scope to add any SOR in the existing tender.
Other Tanks:
During engineering development, there have been additions of some nozzles which are required for the
proper functioning / safety of the tank and it is mandatory to procure these from B&R due to interface
and testing requirements. As B&R scope in the original PO is SOR based, these nozzles are an additional
scope to the tender. A nomination PO for the Supply, Fabrication and Installation is therefore
recommended for these additions.
Some of the nozzles, where engineering alternatives are available have been excluded from B&R scope
and those will be executed separately.
ANNEXURE-03 B&R ACCEPTANCE