Professional Documents
Culture Documents
S4 Rev 20 Software Switches 1
S4 Rev 20 Software Switches 1
Ignition
Ignition Ignition ON within Ignition Ignition
ON OFF 5 seconds OFF ON
LED on bike
Press GREY button Press both buttons
Flashes rapidly
Simultaneously within 10 seconds
For 3 seconds
Confirmation beep 3 seconds
1426
(3 long tones if incorrect confirmation)
The PIN can be changed at any time by entering a new number by the above procedure
Coding new transmitters, changing siren tones, passive arming selection and movement/shock adjustment
It will not be possible to follow the procedures below without first having registered a PIN number to the alarm system
Enter PIN number (after last number has been entered a long tone will be heard)
Turn ON Ignition switch then press Grey button on a new or existing transmitter
If new transmitter - (The new transmitter will now have been coded to the alarm)
Exit OR
To proceed to siren tone or passive arming section (Software Switches) turn Ignition back ON
Within 15 seconds of hearing these tones
Software Switch number Press buttons to enter Method of altering setting and accepting
Toggle to desired Switch desired Switch To exit Software switches at any time
turn Ignition switch off
Switch 1
(Customer selectable)
Change siren tones
Press Grey button to toggle to Grey button = Next tone
switch 2 &3
Press Black button = Previous tone
Alarm will beep once to confirm
To toggle between switches
Switch 2
(Customer selectable) Grey button/LED ON = Full passive arming
Alarm arming method
Black button/LED OFF = Passive Immobiliser
Alarm will beep twice to confirm Press (Default)
switch number
Engineer Switch 1
Erase OTHER transmitter Both buttons (A double beep will be heard) to erase all transmitters
codes except for the one being used
Press
Press Both buttons to save and exit back to switch selection
Engineer Switch 2
Resets software switches Both buttons (A double beep will be heard) to confirm
to factory default settings all software switches have been reset to factory default settings
Press
Press Both buttons to save and exit back to switch selection
Engineer Switch 3 Number Number of LED Flashes = Cause of trigger
of LED Last trigger shown first. Pressing the Grey button to take you back
flashes through previous triggers. Press the Black button to erase the memory
To recall the last 5 alarm
triggers 1 Loss of main power or earths (Fuse blown, Wires cut, etc)
3 Movement trigger - The machine has been moved (S4 Red and Green
only)
Press
4 Nudge trigger (The machine has been knocked repeatedly)
(Please note: On S4 Red and Green this only works if the nudge sensor is
set to ‘fully active’)
To toggle between switches
6 Trigger circuit 2 has been activated (Side stand, Accessory loop, etc) - S4
Red and Green only
Press Both buttons to save and exit back to switch selection
Engineer Switch 4 Number of LED Flashes = Tilt setting 2 to 9 (Default setting 7)
S4 Red & Green only Black button alters angle of tilt the bike requires to activate alarm.
Movement sensor set up
Press Grey button & move machine to test, alarm beeps when tilt detected
Press Both buttons to save and exit back to switch selection
Engineer Switch 5 Number of LED Flashes = Sensitivity setting 1 to 10 (Default setting level 8)
Press
Press Both buttons to save and exit back to switch selection
Engineer Switch 7
Panic Grey button = Panic ON (LED ON) (Default setting)
Black button = Panic OFF (LED OFF)
Press
Press Both buttons to save and exit back to switch selection
Engineer Switch 8 Number Number of LED Flashes = Warn-away setting
of LED (Default setting 3 LED flashes)
flashes
1 Instant Trigger – Triggers on first impact/movement detection
Nudge sensor
2 1 Warn-away beep and trigger on second impact within 2 minutes
6 Permanent warn – away. The alarm will beep to warn off but will not
trigger the alarm into a full reaction (S4 Red and Green only)
7 No Reaction. The shock sensor is turned OFF (S4 Red and Green only)