Professional Documents
Culture Documents
DSA0070823
DSA0070823
LQ190E1LW01
TFT-LCD Module
CUSTOMER :
1 2 3 4
REVISION HISTORY
1st issue.
01A Apr. 9,2004 K. Yonemura T. Ito F.Yamada Change manufacture
to SHARP.
RoHS standard
conformed product.
02A Jan. 27,2005 K. Yonemura E.Nitto T.Ito F.Yamada
Change manufacture
to SHARP.
B B
C C
D
DOCUMENT CONTROL SECTION
E
DATE
1
1 2 3 4
TABLE OF CONTENTS
1㧚APPLICATIONS 3
A A
2㧚PRODUCT NAME AND MODEL NUMBER 3
2-1.Product Name 3
2-2.Model Number 3
3㧚OVERVIEW 3
4㧚CONFIGURATION 3
5㧚MECHANICAL SPECIFICATIONS 4
6㧚ABSOLUTE MAXIMUM RATING
B 5 B
7㧚RECOMMENDED OPERATING CONDITIONS
5
8㧚ELECTRICAL SPECIFICATIONS
6
9㧚OPTICAL SPECIFICATIONS
8
10㧚INTERFACE SPECIFICATIONS 12
10-1.Signal Descriptions 12
10-2.LVDS Data Assignment 13
10-3. Color Data Assignment 15
10-4. Input Signal Timing 16
C 10-5. Correspondence between Data and Display Position 18 C
10-6.Power Supply Sequence 18
11㧚BACK-LIGHT SPECIFICATIONS 19
11-1.Pin configuration for Back-light 19
11-2.Life 19
11-3.Lamp assembly set 19
12㧚APPEARANCE SPECIFICATIONS 20
12-1.Appearance 20
12-2.Dot defects 21
D
13㧚ENVIRONMENTAL SPECIFICATIONS 22
D
14㧚INDICATIONS 23
15㧚PACKAGING 23
DOCUMENT CONTROL SECTION
15-1.Packing Specifications 23
15-2.Packing Method 23
16㧚WARRANTY 29
17㧚PRECAUTIONS 29
18㧚PRECAUTIONS FOR USE 36 E
19㧚MISCELLANEOUS 36
DATE
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
1. APPLICATION
This specification is applied to the 19-inch SXGA supported TFT-LCD module.
A A
B B
3. OVERVIEW
This LCD module has a TFT active matrix type liquid crystal panel 1280x1024 pixels, and
diagonal size of 48cm(19-inch). This LCD has a LVDS dual interface and can display
16,777,216 colors.
C C
4. CONFIGURATION
This LCD module consists of a color TFT-LCD panel that is mounted with TFT driver ICs
D 䌡䌮䌤 a cold-cathode fluorescent tube back-light.
The inverter for the back-light is not included.
D
Figure 4-1 shows a block diagram of this LCD module.
DOCUMENT CONTROL SECTION
DATE
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
07 20050420 The model name was changed.
F
䕣䕘䕕䕕䕤
1
1 2 3 4
RXO0+ RXE0+
A RXO0- RXE0- RSDS I/F A
RXO1+ RXE1+
RXO1- RXE1- Data driver
RXO2+ RXE2+ LVDS Internal
Receiver Circuit
RXO2- RXE2-
RXO3+ RXE3+
Gate
RXO3- RXE3- DC/DC converter
Driver
TFT color LCD panel
RXOC+ RXEC+
1280x3(RGB)x1024
RXOC- RXEC-
PD Bias voltage
SEL LVDS Supply circuit
B B
Vcc Back-light
(+5V) (4 CCFL)
(Separate)
Power
supply Inverter circuit
C C
Figure 4-1 Block Diagram
5. MECHANICAL SPECIFICATIONS
Table 5-1 shows the mechanical specifications of this LCD module.
D
Dimensions 404.2x330x20(TYP.) mm
Edge type back-light is used. D
(CCFLx4)
Display
(1280x3)x1024 —
Resolution Without inverter.
DOCUMENT CONTROL SECTION
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
A A
Table 6-1 Absolute Maximum Rating
Item Symbol Condition MIN. TYP. MAX. Unit
B B
D
DOCUMENT CONTROL SECTION
E
DATE
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
8. ELECTRICAL SPECIFICATIONS
Table 8-1 shows the electrical specifications of this LCD module. Figure 8-1 shows the
A A
measurement circuit. Figure 8-2(A) shows the equivalent circuit of the logic signal input area.
Figure 8-2(B) shows the equivalent circuit of the supply voltage Input area.
Differential-input
VIH — — 100 mV
Voltage (Hign)
VCM=+1.2V
Differential-input
VIL –100 — — mV
B Voltage (Low) B
fL=50kHz
Lighting Voltage VL — 750 — Vrms
IL=7mA
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
+5V Icc
A
A
Vcc Logic Analog Driver
GND
DC/DC
CL Converter
AC
Vs Back-light
B B
GND 䌉L LCD module
D
Figure 8-2(A) Equivalent circuit of logic signal Input
D
FB
Fuse
Internal
DOCUMENT CONTROL SECTION
Vcc
FB Circuit
GND 100pF 10ǴF
FG䋨Frame ground䋩
E
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
9. OPTICAL SPECIFICATIONS
Table 9-1 shows the optical specifications of this LCD module.
A A
Table 9-1 Optical Specifications Ta=25˚C䋬Signal timing=Typ.
Specifications Remark
Item Symbol Condition Unit
MIN. TYP. MAX. Note
TITLE L Q 1 9 0 E 1 LW 0 1
05 20040802 Revise of Response time. ( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
04 20040708 Revise of Response time. CUST.
03 20040625 Addition of Response time. LD17443
F
䕣䕘䕕䕕䕤
LCD module
B B
Y-
Bottom (6 o’clock Direction)
X-
Left (9 o’clock Direction)
䋪ń ljU䋽䋰°䋬ljD䋽䋰°䋬ljL䋽䋰°䋬ljR䋽䋰°
㱔L,R,U,D
Display Surface =0㫦
D
Figure 9-2 Definition of Viewing Angle (2)
D
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
Relative
Brightnes Black 10% 10%
0% Black
3 3
0%
Ǖrise Ǖfall
B B
ON Response Time OFF Response Time
X+
Z- Z+
Brightness Meter or
㱔 Luminance colorimeter
(with luminosity
D correction function)
X-
D
Y-
DOCUMENT CONTROL SECTION
TITLE L Q 1 9 0 E 1 LW 0 1
05 20040802 Addition of response time definition. ( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
03 20040625 Change response time definition. CUST.
02 20040602 Change response time definition. LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
A A
MAX
Contrast
Ratio
10
B B
䋨-䋩 0 䋨+䋩
6 o’clock㸠 Viewing Angle㱔 㸢12 o’clock
䌼Min. In䌼
Brightness Uniformity (䂦L) 䋽 × 100 (%) , n = 1 to 9
䌼Max. In䌼
D 㽲 㽵 㽸 154
D
㽳 㽶 㽹 512
870
DOCUMENT CONTROL SECTION
㽴 㽷 㽺
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
Tx OUT2+ 19 RxE2+
BE6 23 TxIN21 55 RxOUT21 BE6
BE7 24 TxIN22 1 RxOUT22 BE7
RSVD 27 TxIN24 3 RxOUT24 Not use
Tx OUT2- 18 RxE2-
RSVD 28 TxIN25 5 RxOUT25 Not use
RSVD 30 TxIN26 6 RxOUT26 Not use
RE0 50 TxIN27 7 RxOUT27 RE0
RE1 2 TxIN5 34 RxOUT5 RE1
GE0 8 TxIN10 Tx OUT3+ 23 RxE3+ 41 RxOUT10 GE0
GE1 10 TxIN11 42 RxOUT11 GE1
BE0 16 TxIN16 49 RxOUT16 BE0 E
BE1 18 TxIN17 Tx OUT3- 22 RxE3- 50 RxOUT17 BE1
RSVD 25 TxIN23 2 RxOUT23 Not use
TxCLK OUT+ 21 RxCLK IN+
DCLK 31 TxCLK IN 26 RxCLK OUT Not use
TxCLK OUT- 20 RxCLK IN-
*1 䊶RSVD (reserved) pin on a transmitter should be connected with Ground.
䊶Input odd or even data depending on the display position of the LCD module.
DATE
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B
B
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
× 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
× : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : :
䌒䌥䌤
Ø : : : : : : : : : : : : : : : : : : : : : : : : :
Brighter 253 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
C Ø 254 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C
Red 255 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
× 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
× : : : : : : : : : : : : : : : : : : : : : : : : :
䌇䌲䌥䌥䌮
: : : : : : : : : : : : : : : : : : : : : : : : :
Ø : : : : : : : : : : : : : : : : : : : : : : : : :
Brighter 253 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0
Ø 254 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
Green 255 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
D Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
× 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
× : : : : : : : : : : : : : : : : : : : : : : : : : D
: : : : : : : : : : : : : : : : : : : : : : : : :
䌂䌬䌵䌥
Ø : : : : : : : : : : : : : : : : : : : : : : : : :
DOCUMENT CONTROL SECTION
Brighter 253 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1
Ø 254 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
Blue 255 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Note.1) Definition of gray scale:Color (n)…”n” indicates gray scale level.
Larger number means brighter level.
Note.2) Data; 1:High, 0:Low
E
Note 3) Color data consist of 8 bit red, green and blue data of odd and even number pixel data.
Total data number is 48 signals. This module is able to display 16,777,216 colors because
each red, green and blue data is controlled independently.
DATE
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
*2)•If the “High” level period of ENAB is less than 640 DCLK or the number of ENAB in a frame
period (Tv) is less than 1024, black color is displayed at the rest of the display area.
*3)•If ENAB does not synchronize with the effective display data, the display position does not fit
to the display area.
*4)•Hor. Period (2) shows the operating range where internal circuit can work correctly.
D 䊶When ENAB signal is out of Hor. Period (1), the display quality may deteriorate.
D
DOCUMENT CONTROL SECTION
E
DATE
TITLE L Q 1 9 0 E 1 LW 0 1
( F L C 4 8 S X C 8 V- 11 A A )
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
Tc
TclkL Tclk
A A
2.3V 1.65
DCLK 0.9V
Tch
Tc1 Tset Thold
ENAB 2.3V
RO7-0, RE7-0
GO7-0, GE7-0 0.9V
BO7-0, BE7-0
B B
RO7-0, RE7-0
GO7-0, GE7-0
BO7-0, BE7-0 Th
ENAB
Thd
Tvd
Tv
Tc
DCLK
D
0001 0005 0009 1269 1273 1277
0003 0007 0011 1267 1271 1275 1279
RO7-0, RE7-0 D
GO7-0, GE7-0
BO7-0, BE7-0
0002 0006 0010 1270 1274 1278
0004 0008 0012 1268 1272 1276 1280
DOCUMENT CONTROL SECTION
ENAB
Tdn Tdn
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
A A
S0001 S0002 S0003 S0004 S0005 S0006 S0007 S3839 S3840
RO GO BO RE GE BE RO GO GE BE
C001 0001 0001 0001 0002 0002 0002 0003 0003 1280 1280
B B
RO GO BO RE GE BE RO GO GE BE
C1024 0001 0001 0001 0002 0002 0002 0003 0003 1280 1280
C C
10-5 Power Supply Sequence
The sequence of input signals and On/Off of the power supply of this LCD module
should be in the specification shown in Figure 10-3 to prevent latch-up of the
driver ICs and DC driving of the LCD panel.
T4㻡20ms(Voltage descent)
亖
亖
Vcc ON 4.75V
4.75V 0.5V
4.75V 0.5V
㩷㩷
D (4.5V)
OFF T6㻡20ms
(0V) T1㻡20ms 0ms㻡T3
2.0V
D
PD 0.5s㻡T7
亖
亖
LVDS H
90%
Tri-state
DOCUMENT CONTROL SECTION
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
11. BACK-
BACK-LIGHT SPECIFICATIONS
11-1 Pin configuration for Back-light
A Table 11-1 shows the description and Pin assignment of the connectors A
(CN-A to D) for the Back-light of this LCD module.
Table 11-1 Pin Assignment of CN-A to CN-D
Pin Signal
Function Cable color
㷗 CN-A CN-B CN-C CN-D
1 䌖䌌 1 䌖䌌 2 䌖䌌 3 䌖䌌 4 Power supply Pink ,Orange
2 — — — — — —
3 GND GND GND GND Ground Blue, Gray
B B
Connector : Housing : BHR-03VS-1
Contact : SBH-001T-P0.5
User’s Connector : Post with base: SM02(8.0)B-BHS-1-TB
Supplier : Japan Solderless Terminal Trading Company LTD. (J.S.T.)
11-2 Life
The life of the back-light is a minimum of 50,000 hours at the following conditions.
(1) Working conditions
㽲Ambient temperature䋺 25㫧5㷄
C C
㽳Tube current (IL) 䋺 7mA or less
E
DATE
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
07 20050420 Lamp Assy No. was changed.
F
䕣䕘䕕䕕䕤
1
1 2 3 4
A A
No. Item Judgment method and standard
1 Bright spot (high and Low) <4 dots (Note 1 )
2 Bright spot connection <2 pair (Note 1)
(high and low) (2 dot connection in horizontal only)
3 Total of bright spot <4 dots
4 Dark spot <8 dots (Note 2)
5 Dark spot connection <3 pairs (Note 2)
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
A A
12-2-1 Zone
· Inside display dot area (376.32×301.056mm)
· Display dot area means active area.
· One pixel consists of 3 dots (red, green and blue).
· Foreign particle and scratch unharmful to display image, such as the foreign particle
under polarizer film but outside of the display area and scratch on metal bezel, backlight
module or polarizer film out of the display area, etc., are not counted.
· Inspector must observe the LCD screen from the normal direction under the illumination by
a single 20W fluorescent lamp. The distance between the LCD screen and the inspector
should be a height of 50cm above the worktable.
The vertical illuminance is 300 to 600lux (reference value).
D · Bright spot should be counted under entire black screen.
· Dark spot should be counted under entire white screen.
· Input signal timing should be typical value. D
(Note1) Please do not mistake a single bright spot for a bright spot connection due to
DOCUMENT CONTROL SECTION
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
NOTE䋺 Table 13-2 and Figure 13-1 show the shock resistance standard when module is packaged.
C C
Table 13-2 Shock resistance standard when module is packaged
D C (Edge)
D
B (Edge)
A (Corner)
I (Front face) D (Edge) H (Bottom face)
E
Figure 13-1 Direction to apply shock to package
DATE
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
14. INDICATIONS
This module has the following indications.
A A
(1) Product name : LCD 䌵䌮䌩䌴
Serial number
(To be reset every month on 1st.)
B B
Manufacturing month
(Oct. = X, Nov. =Y, Dec. =Z)
Bar code
FLC48SXC8V -11A A 5600001
LQ190E1LW01 01A
SHARP CORPORATION
D
D
Figure 14-1 Product Label (Example)
DOCUMENT CONTROL SECTION
15. PACKAGING
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
07 20050420 Model name and Company Name was changed CUST.
LD17443
02 20040602 Correction of packing box size.
F
䕣䕘䕕䕕䕤
1
1 2 3 4
A Protective sheet A
Front side
B B
Rear side
C C
Anti-Electric Bag
DOCUMENT CONTROL SECTION
Front side
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
Partition Box
Anti-
Electrostatic bag A
A 㽲 㽳
LCD Unit
B B
C C
Holder
㽴 㽵
D
DOCUMENT CONTROL SECTION
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
Holder
㽶 㽷
A A
B B
㽸 㽹
C C
464
499
Carton Box 250
D
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
07 20050420 Model name was changed. LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
A A
Corrugated
B B
PP Belt
1000
1000
DOCUMENT CONTROL SECTION
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
A A
Corrugated carton (A)
Cushioning material with LCD modules
B B
(580)
602
446 646
(430) (630)
C C
Note 1) The carton (A) should be placed in the middle of the container (B) with enough cushioning
materials.
D
DOCUMENT CONTROL SECTION
E
DATE
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
16.WARRANTY
The warranty period is one year after shipping. Products which fail during this period are
repaired or replaced without charge, unless the failure is caused by user. A
A
17.PRECAUTIONS
Adhere to the following precautions to use this LCD module properly.
[Dirt ] Apply clear water to a soft cloth and squeeze hard out of water drops, then lightly
wipe off the specified parts. Only if the dirt is hardly wiped off, use isopropyl alcohol
or ethanol.
Be careful not to splash the water or the solvents on the edge of polarizer and in the
LCD unit. E
The polarizer possibly exfoliates due to the solvent and water penetrated between
the polarizer and the LCD panel.
Do not use unspecified solvent such as ketone (acetone, etc.) and aromatics (xylene,
toluene, etc.)
DATE
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
(Caution) Be careful not to allow the water or solvent to enter the module.
㨯If saliva or water drops are left for a long period of time, the part may become A
A
deformed or discolored.
Wipe off immediately in the same way as for dirt.
㨯Do not allow oil to adhere to the module since excessive oil is hard to clean.
㽵 Do not place or contact objects on the display surface for a long period of time.
This may make some parts of the LCD module distorted and the quality of display may
deteriorate.
㨯Floor of work area and work table to assemble the LCD module should be covered with
electrostatic shielding in order to discharge static electricity via an earth wire.
㨯If necessary, ground operation tools (soldering iron, radio pliers, tweezers, etc.).
㨯Do not take the module out of the conductive bag until the module is assembled.
㨯Do not assemble the module under low humidity (50%RH or less).
㽵 Do not pull the connecting cable on the rear face of the LCD module strongly.
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
㽴The following troubles occur when the LCD module is not used under recommended
temperature. A
A
㨯Operation under high temperature(>50͠): Display colors shift to blue.
㨯Storage under high temperature(>60͠): The polarizer film deteriorates and contrast
decreases.
㨯Operation under low temperature(< 0͠): The response speed decreases considerably.
㨯Storage under low temperature(<-20͠): The liquid crystal may solidify and become
B damaged. B
㽵Be sure to input
input the control signals at the correct timing.
If control signals (DCLK, ENAB) are not input, or if the timing is out of the specified timing,
DC voltage may be applied to the liquid crystal and, as a result, cause image sticking or
deterioration of contrast.
㽲Excessive force should not be applied to the screen or the rear side of the LCD module.
Excessive pressure on the screen caused by the installation of the LCD module may
deteriorate display quality and reliability.
C Brightness uniformity and the reliability of CCFL may decrease if the pressure is applied to C
the backlight module.
㽳Avoid twisting and bending the LCD module.
Excessive twist and bend may damage display quality and reliability.
㽴Avoid extending the power cable between the LCD module and inverter.
This may cause the backlight to flicker or not to light.
㽵Keep the backlight cable apart from the metal enclosure of the LCD module.
When frequency current for backlight driving leak to the metal enclosure, the desired
D brightness may not be assured.
㽲Do not store the LCD module in an atmosphere of organic solvent or corrosive gas.
In an organic solvent atmosphere, the polarizer film discolors and display quality
deteriorates.
In a corrosive gas environment, various parts of the module may corrode or deteriorate.
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
07 20050420 Company Name was changed
F
䕣䕘䕕䕕䕤
1
1 2 3 4
㽴The LCD module is recommended to be stored in humidity controlled, cool and dark
locations.
Recommended storage environment A
A 䊶Place : Dark (avoid direct sunlight)
䊶Temperature : 10㨪35͠
䊶Humidity : 50㨪60%RH
Note) If the module is left in an environment of 60͠ and above for a long period of time,
optical characteristics may deteriorate.
Fluorescent lamps driven by high voltage are included in this LCD module. Please stand
C to the instructions below when designing inverter that lights the fluorescent lamps. C
Otherwise it may lead to FATAL FAILURE, such as SMOKING or FIRING.
㽲 APPLY PROTECTIVE CIRCUIT in preparation for lamp breaking, wire breaking and
short circuit. The protective circuit should also detect half open circuit and wire breaking
in narrow gap etc.. Otherwise it may lead to fatal failure.
㽳 KEEP ENOUGH CURRENT CAPACITY of inverter output for leakage current, which
D leaks from lamps and wire to surrounding metal material. Usually output current of
about 1.5 times as same as the lamp current is necessary. But it sometimes varies due to D
characteristics of the inverter itself. So before determining design, please check
characteristics of the inverter by connecting it to the LCD module.
DOCUMENT CONTROL SECTION
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
㧔8㧕Return method of the LCD module requested for repair or analysis of the problem
When returning the LCD modules, adhere to the following procedures not to damage the LCD A
A
panel or the backlight cables. (Fig. 17-1(a)~(b))
When the LCD module is returned without following the specified packaging procedures,
SHARP will not take responsibility for the damages caused by the failure of the packaging
method.
Please be cautious not to put fingerprints or other stains on the display by
wearing a glove or fingerstall when managing LCD module modules, including
faulty modules that require to be returned .
B B
C C
Rear side
* If the cables are not fixed, the connectors
may scratch the LCD panel surface or the
Backlight cable
D cables may be damaged.
D
Anti-electrostatic bag
Front side E
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
07 20050420 Company Name was changed
F
䕣䕘䕕䕕䕤
1
1 2 3 4
㽳 Electrostatic bag
㽲
LCD Unit
B B
C C
Holder
㽴 㽵
D
D
DOCUMENT CONTROL SECTION
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
LD17443
07 20050420 Company Name was changed
F
䕣䕘䕕䕕䕤
1
1 2 3 4
Holder
A 㽶 㽷 A
B B
㽸 㽹
C C
464
499
D Carton Box 250
D
DOCUMENT CONTROL SECTION
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
07 20050420 Company Name was changed
LD17443
F
䕣䕘䕕䕕䕤
1
1 2 3 4
(9) Others
㽲If the LCD panel is damaged, do notnot inhale and do not swallow the liquid crystal.
If the liquid crystal adhere to the body or cloths, wash it off with soap immediately. A
A Follow regular precautions for electronic components.
19. MISCELLANEOUS
Specifications of the TFT-LCD panel and other components used in the LCD module are
subject to change. Both parties shall discuss together before change.
If any doubt is raised in the content of the specifications, both parties shall discuss and make
D best effort for the agreement.
D
DOCUMENT CONTROL SECTION
E
DATE
TITLE LQ190E1LW01
(FLC48SXC8V-11AA)
DRAW. NO.
CUST.
07 20050420 Company Name was changed
LD17443
F
䕣䕘䕕䕕䕤
1
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited
Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND
FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,
for any incidental or consequential economic or property damage.