wort,
PRODUCT SPECIFICATION OF SUPERBRIGHT PIMA ACRYLIC PANELS
‘The Product Specification describes the working specification for the design, supply and installation of
SUPERBRIGHT PMMA acrylic panels for swimming pools and water features. They ate in accordance to the
method statement deployed by WORLDBIZZ PTE LTD and the manufacturer's Code of Practice.
SUPERBRIGHT PMIMA clear, opaque, tinted or translucent Acrylic Panels in custom dimensions and thickness to
manufacturer's specification. PMMA acrylic panels become ultra violet resistant during the fusion process which
‘can be achieved only at high temperature of 110 degrees Celsius. All panels are cured in dry kiln facility. PMMA
‘acrylic panel uses only 100% of Lucite raw materials required of PMMA specifications as oppased to poor quality
non-standard PMIMA acrylic panels that uses a mix of raw componentsand plastics. The high temperature allows
for better strength panels as it removes all impurities. This is opposed to traditional water processed acrylic
ppanels that are manufactured at only 99 degrees Celsius when water reached its boiling point. Only high
temperature kiln-dry process ensures high strength PMMA structural acrylic panels. PMMA acrylic panel thus
‘maintains clarity throughout with turning yellow.
Physical Properties:
The physical properties are stated in the attached Working Specification of PMMA acrylic panels.
Product Warranty
‘The product warranty is for five (05) years limited to the manufacturer's specification and application. Terms
{and conditions apply. The warranty does not cover damages made by third parties when foreign chemical agents
are applied. The Product Warranty covers the following!
Product uses Lucite raw components for MMA and Monomer.
Warrants against pane! turning yellow.
‘Against water leakages or seepages through acrylic panels.
‘Against workmanship with chemical welding detail
Inclusion and Bubble
+ The count ares and the permitted area per 1m” ofthe viewing size are shown below
. Count Area 25230 [ mm?
Inclusion [Toial Permitted Area 100 mm?
Count Area 25=30 | mm?
Bubble [Total Permitted Area 150. mm?
‘= Those which size is smaller than count area, should be acceptable,
‘+The maximum length of inclusion and bubble at the butt-joint part should be less than 10mm per
L meter of the viewing size
Chemical welds must only be performed by qualified and experienced specialist technicians
‘Scope:
‘To design, supply and install clear Acrylic Viewing Panels in custom dimensions and thickness to manufacturer's
specification. The thicknessis based on design calculation and endorsed by the appointed Professional Engineer.
[BCA stibmission is NOT included but is an option. Professional Engineer arid RTO fees for BCA submission are
ppayable under separate charges. All preparation and installation works are carried out by specialist technicians
who are trained in chemical welding, special cut techniques and proprietary installation standard of the
manufacturerorlBies
PRODUCT SPECIFICATION OF SUPERBRIGHT PIMA ACRYLIC PANELS
PROPERTIES asi oni AGRE
Specie Gravy Danas i
‘Optical aac ie Pere is
ight Transmittance 0100561
Paalel = 3%
Tosa! — % 33
Haze % iz
Mechanical | Tense Srenaih - Daa
igen |
Kalen? aon Se
Elongation t Rupture % a5
Tewralseengih Dos
C raat no |
Modulus of Esty igen! STE
T
Compressive Senge DaasesT
vie — Talent Tae
Modus of Easticty glen 3x10
Drarae —| wer? 630
Impact Sera Dae
“charpy neice ienjen | 20
Roakwel nara Das ao
Thermal Ht Faring Temperature % 30.180
Heat Distortion Temperature C/Min-26tpa ua 00
‘Coefficient of Thermal Expansion DBE emremFe—| To
Manimum Rezervmendes Confnaous See Teiperature °c eS
‘oeffcantof Thermal Conducuvty reamnert | 018
Speatie Hest coerce [035
‘Miselaneous | Farmabiy (Baring Rate] — aes [wmyam [3
Water Absorption Weight gain on inmerion for 2 hours) 057063 | 03
Soluble Mater oat after immersion = 0
‘Odour None
[MAXIMUM INTIAL OEFLECTION
‘ledges supported
51/300 of shorter opening eneth
Top and bottom edges supported and both sides sean onted
1/500 of shorter opening length
[MAXIMUM STRESS
ong tom allowable stress
‘ase at but int
‘ob TOR? without bat jlnt
DIMENSIONAL TOLERANCE
Tiehness 15% (normal hens) panels 100mm
13% panel 0
Leneth 288m of lent an width
Fatnere 51/200 shorter eng)
Warp & Tt 2.5mm per 3Ddrwm when measured unrestrained on ft surface
ges Edgos tobe chamfered "45, refer drawings
Poko Ratio 035
=
axv06 KF
26 M\mer|
Sxrg§ Kent