Professional Documents
Culture Documents
KCE Meni
KCE Meni
Accept
Fault Log Fault Log Operation Selection Fault List Fault Code
Accept Accept Timeout
Menu Menu Timeout
Fault Log Clearing
Menu
Elevator Parameters Parameter ID Selection Parameter Vector Selection Parameter Value Edition
Accept
Menu
Menu 2 available, If the parameter is not vector this
if param state is skipped
DRIVE_TYPE = 1 Menu Dot indicates if parameter is vector
(Serial Drive) Encoder Polarity
Drive Parameters
LWD Type
Menu
Menu
Display and Tests Selection Start Counter
Menu
KEN Number
Elevator Parameters
Menu
Menu
Accept
Repeat Repeat
(inc) (Dec)
Accept/Menu
LWD Type
Repeat Repeat
(inc) (Dec)
DMI_ERROR MSG
Accept
(SET_KNOWN_PARAM)
KMI (BUI) Screen Map – Menu 4
– Display and Tests
Floor Markings
Incre Decre
Start Counter
Menu Accept
Menu
Incre Decre
Comissioning KCECPU Version Number
Incre
CPU IP Decre
Incre
Subnet Mask Decre
Incre
Gateway IP Decre
Incre
KEN Number Decre
Incre
DTS Time
Decre
Repeat Repeat
(inc) (Dec)
Incre Door Close End Signal state when doors are open
Decre for side A, Side B and side C (from right to left)
Door Close End Signal
C B A
KMI (BUI) Screen Map – Menu 4 – 1
– Elevator mode names
Normal Mode Pendant Mode
Attendance Service
Fire Detection
Repeat Repeat
(inc) (Dec)
Repeat Repeat
(inc) (Dec)
Accept {lwd
setup0}
Menu
Accept
LWD_EMPTY
Accept/Menu
DMI_ERROR MSG
Accept
Menu (GET_KNOWN_PARAM)
DMI_ERROR MSG
Accept
(SET_KNOWN_PARAM)
BUI Screen Map For LWD Setup to Calibrate Drive to Half Load
LWD_EMPTY
Decre Incre
Menu
LWD_HALF
Accept
DMI_ERROR MSG
Accept
Menu (GET_KNOWN_PARAM)
Current half load value in drive (45) will blink – edit mode -(
LWD Value Browse to select the value from the valid range given by drive)
Repeat Repeat
(inc) (Dec)
DMI_ERROR MSG
Accept
(SET_KNOWN_PARAM)
BUI Screen Map For LWD Setup to Calibrate Drive to Full Load
Menu
Accept
If Lift in RDF mode
Accept
LWD_EMPTY
Incre Decre
Menu
LWD_FULL
Accept
DMI_ERROR MSG
Accept
Menu (GET_KNOWN_PARAM)
Current full load value in drive (100) will blink – edit mode -(
Browse to select the value from the valid range given by drive)
LWD Value
Repeat Repeat
(inc) (Dec)
DMI_ERROR MSG
Accept
(SET_KNOWN_PARAM)
BUI Screen Map For Well Access Protection Mode
Activation
(Modified 20th April 15)
Display and Tests
(Detailed flow
diagrams
available with
Menu sheets – ‘lwd
setup with 3
points’, ‘Set
LWD setup Empty LWD’, ‘Set
Comissioning Comission Selection LWD Adjustment Half LWD’ and
‘Set Full LWD’ )
Menu
Accept
If DOP is off
Allow Well Access Protection for
TOC (OR PIT)
Repeat Repeat
(inc) (Dec)
mode/moving/not at
door zone
Confirm Pairing
Group
BUI Screen Map For PIN Code Configuration Mode
Activation
Display and Tests (Modified 23rd May 16)
(Detailed flow
diagrams
available with
sheets – ‘lwd
Menu setup with 3
points’, ‘Set
Empty LWD’, ‘Set
Half LWD’ and
LWD setup ‘Set Full LWD’ )
LWD Adjustment
Comissioning Comission Selection
Menu
OSS/PrC/LoC will blink to
indicate user press Accept
Incre
Decre
Menu
Menu
Incre
Decre
Accept
Menu Accept
Group
(Detailed flow
diagrams
available with
sheets – ‘lwd
setup with 3
points’, ‘Set
Menu Empty LWD’, ‘Set
Half LWD’ and
‘Set Full LWD’ )
LWD Adjustment LWD setup
Comissioning Comission Selection
Menu/accept
Group
Factory Default Parameters
(Detailed flow
diagrams
available with
sheets – ‘lwd
setup with 3
points’, ‘Set
Menu Empty LWD’, ‘Set
Half LWD’ and
LWD setup ‘Set Full LWD’ )
LWD Adjustment
Comissioning Comission Selection
Pairing
Menu
Accept
Menu
Otherwise
(Min. needed is LDG call
Menu
prevention(262).DOP/
RDF also allowed state)
Menu
1-64-
Accept
Menu
Press Menu/Accept
Group button. It ends the lock
group setup.
BUI Screen Map For Group Menu (Faults and
Parameters)
(Modified 13th OCT 16)
Menu 8 - Group
available, if param
GROUP_TYPE = 1
Group
Establishing Group
Connection (STIF Protocol).
Accept “In Progress” will scroll
here
Menu/Accept
(wait for 20sec)
No connection to group/ STIF connection
lost
Menu Timeout
OR
!Fault Active
Incre
Indicates that Lift is under GC Fault Log Decre Fault Log Operation Selection Fault List Fault Code
Group Control (In Bank) Accept Accept Timeout
Menu Timeout
Menu
Fault Log Clearing
Incre
Decre
Group parameters( park) – Park enabled/disabled Parameter value selection
GC Parameter Set ID
Accept Accept Accept
Park Floor
Accept
Menu
Park Door
Accept
Menu
Incre
Decre Accept changes
Accept
Menu
No parameters available
Accept
Park and subs are visible only when feature
Accept activeted from KMC / Promanager
(Example)Next available
parameter (set id)
Incre
GC Fault Log Decre
Incre
Decre
Group parameters( park) – Parameter Ids
Set ID Park enabled/disabled Parameter value selection
GC Parameter
Accept Accept Accept
Incre
Decre Parameter value selection
Allowed lifts Param value index selection
Accept Accept
Menu
Menu
Incre Incre
Decre Decre
Accept/Menu Incre
Save the edited
Decre
Incre parameter values “End” screen informs
Accept the user that
Decre parameter index ends
here and the “Accept
key” press takes to
Park Door Parameter value selection “Parameter Ids”
Accept screen
Menu
Accept changes
Accept
Menu
Comissioning
If the parameter
GROUP_TYPE is 0, then we
can navigate from Menu 5 to
Menu 9. (i.e. Menu 8 not
available)
Menu
Default Screen
Menu 9 available, if param
DRIVE_TYPE = 1 (Serial Drive)
Drive Tests
Drive Type Not
Menu
Valid OR Test Ids Menu
not available
Accept
Menu
Lift in RDF mode
Accept
Valid Drive
(Test IDs – assumed to be max. 3 digit
Drive Tests IDs Drive Tests IDs length)
Incre
Decre
Incre
Accept/Menu Decre
Accept/Menu