Professional Documents
Culture Documents
Tolerances and Measuring Technnology - Nhom 01FIE: Câu hỏi
Tolerances and Measuring Technnology - Nhom 01FIE: Câu hỏi
/ CHAPTER 1_Introduction to Tolerances and Fits / Review Chapter 1 (English) No score, only for practicing
Câu hỏi 1
Sai
Select a transition fit in which the probability of interference is much bigger than the one of clearance when assembling at random.
Select one:
a. D = Ø80-0,030 ; d = Ø80 .
c. D = Ø80+0,030 ; d = Ø80 .
d. D = Ø80+0,030 ; d = Ø80 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 1/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 2
Không trả lời
Select one:
a. D4
b. D2
c. D3
d. D1
Câu hỏi 3
Không trả lời
With given holes having D = Ø110+0,035, choose the size of shafts d so that when assembled, it will create a transition fit having Smax =
32µm:
Select one:
a.
b.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 2/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 4
Không trả lời
For nominal size Ø30, determine if the two shafts with the actual dimensions dt1 = Ø29,073 and dt2 = Ø29,067 meet the requirements.
Select one:
a. Both of them are unrepairable defectives.
c. The first one is unrepairable defective, meanwhile the second meets the requirement.
Câu hỏi 5
Không trả lời
With given holes having D = Ø120+0,035, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a. d = Ø120±0,011.
b. d = Ø120 .
c. d = Ø120+0,022.
d. d = Ø120 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 3/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 6
Không trả lời
Choose the type of fit for piston and cylinder of the internal combustion engine.
Select one:
a. Clearance fit.
b. Interference fit.
d. Transition fit.
Câu hỏi 7
Không trả lời
A clearance fit has D = d = Ø76, TD = 30μm, Smax = 60,5μm, TS = 49μm, and bilateral shaft tolerance zone. Calculate the limiting deviations
of the hole and the shaft.
Select one:
a. EI = 30µm , ES = 60µm ; ei = -9,5µm , es = 9,5µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 4/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 8
Không trả lời
With given shafts having d = Ø28+0,016, choose the size of the holes so that when assembled, it will create a transition fit having Nmax =
27µm.
Select one:
a. D = Ø28±0,027
b. D = Ø28-0,027
c. D = Ø28±0,011
d. D = Ø28+0,027
Câu hỏi 9
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the clearance fit having the average clearance Stb =
59μm.
Select one:
a. 3–c.
b. 4–c.
c. 2–c.
d. 4–a.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 5/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 10
Không trả lời
If a series of holes has D = Ø50±0,012 , select the shafts in order to create a transition fit having Nmax = 0,033 and Smax = 0,012:
Select one:
a. d = Ø50±0,013
b. d = Ø50+0,021
c. d = Ø50+0,016
d. d = Ø50-0,033
Câu hỏi 11
Không trả lời
Select one:
a. 63μm
b. 19,5μm
c. 49μm
d. 38,5μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 6/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 12
Không trả lời
Because of hard machining holes D = Ø50 and shafts d = Ø50-0,016 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Dimensions of hole groups and shaft groups are:
Select one:
a. With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,040 ; group III : Ø50,040 < Dt ≤ Ø50,057.
With shafts, group I' : Ø50,984 ≤ dt ≤ Ø50 ; group II' : Ø50 < dt ≤ Ø50,016 ; group III' : Ø50,016 < dt ≤ Ø50,032.
b. With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,041 ; group III : Ø50,041 < Dt ≤ Ø50,057.
With shafts, group I' : Ø49,984 ≤ dt ≤ Ø50 ; group II' : Ø50 < dt ≤ Ø50,016 ; group III' : Ø50,016 < dt ≤ Ø50,032.
c. With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,040 ; group III : Ø50,040 < Dt ≤ Ø50,057.
With shafts, group I' : Ø49,084 ≤ dt ≤ Ø50 ; group II' : Ø50 < dt ≤ Ø50,016 ; group III' : Ø50,016 < dt ≤ Ø50,032.
d. With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,041 ; group III : Ø50,041 < Dt ≤ Ø50,057.
With shafts, group I' : Ø49,984 ≤ dt ≤ Ø50,004 ; group II' : Ø50,004 < dt ≤ Ø50,018 ; group III' : Ø50,018 < dt ≤ Ø50,032.
The correct answer is: With holes, group I : Ø50,009 ≤ Dt ≤ Ø50,025 ; group II : Ø50,025 < Dt ≤ Ø50,041 ; group III : Ø50,041 <
Dt ≤ Ø50,057.
With shafts, group I' : Ø49,984 ≤ dt ≤ Ø50 ; group II' : Ø50 < dt ≤ Ø50,016 ; group III' : Ø50,016 < dt ≤ Ø50,032.
Câu hỏi 13
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the interference fit having the average interference Ntb =
47,5μm.
Select one:
a. 1–d.
b. 1–b.
c. 3–d.
d. 3–b.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 7/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 14
Không trả lời
From the fit between sleeves and shaft portions 2, 5 of an intermittent shaft in a double reduction gearbox, determine limits of sizes of
sleeve bore and shaft.
Select one:
a. Dmin = Ø45 , Dmax = Ø45,039 ; and dmin = Ø44,975 , dmax = Ø45.
The correct answer is: Dmin = Ø45 , Dmax = Ø45,039 ; and dmin = Ø44,950 , dmax = Ø44,975.
Câu hỏi 15
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the interference fit having Nmax = 51μm.
Select one:
a. 1–d.
b. 3–b.
c. 1–b.
d. 3–d.
Câu hỏi 16
Không trả lời
With nominal size D = d = Ø30, maximum and minimum diameters of holes and shafts in the below diagram of tolerance disposition are:
Select one:
a. Dmax = Ø30,016 ; Dmin = Ø29,997 ; dmax = Ø30,005 ; dmin = Ø29,978.
The correct answer is: Dmax = Ø30,005 ; Dmin = Ø29,978 ; dmax = Ø30,016 ; dmin = Ø29,997.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 9/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 17
Không trả lời
Choose proper dimensions between pulley hole D and shaft d in the below industrial fan.
Select one:
a. D = Ø42+0,025 ; d = Ø42 .
b. D = Ø42+0,025 ; d = Ø42 .
c. D = Ø42±0,012 ; d = Ø42-0,016.
d. D = Ø42+0,025 ; d = Ø42-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 10/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 18
Không trả lời
Suggest limits of size for sleeve bore 8 and shaft 2 on the assembly drawing.
Select one:
a. Dmin = Ø40 , Dmax = Ø40,039 ; and dmin = Ø39,975 , dmax = Ø40.
The correct answer is: Dmin = Ø40 , Dmax = Ø40,039 ; and dmin = Ø39,950 , dmax = Ø39,975.
Câu hỏi 19
Không trả lời
A fit has the following data Td = 32μm, Smax = 56μm, EI = 0, bilateral tolerance of shaft. Calculate the hole and shaft limiting deviations.
Select one:
a. ES = 40μm, EI = 0, es = 20μm, ei = -12μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 11/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 20
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the clearance fit having the average clearance Stb =
42μm.
Select one:
a. 2–c.
b. 4–a.
c. 3–c.
d. 1–c.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 12/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 21
Không trả lời
Determine the limits of size and tolerance of the width of slot B = 10 in the part drawing.
Select one:
a. Bmin = 9,989 ; Bmax = 10,011 ; TB = 0,022.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 13/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 22
Không trả lời
In an interference fit, the maximum interference Nmax and the minimum interference Nmin are calculated by the following formulas:
Select one:
a. Nmax = es - EI ; Nmin = ei - ES.
Câu hỏi 23
Không trả lời
From the fit between rolling bearings and shaft portions 1, 6 of an intermittent shaft in a double reduction gearbox, determine dimensions
of the bearing bore D and the shaft d.
Select one:
a. D = Ø40-0,012 ; d = Ø40±008.
b. D = Ø40+0,012 ; d = Ø40 .
c. D = Ø40-0,012 ; d = Ø40 .
d. D = Ø40+0,012 ; d = Ø40-0,016.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 14/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 24
Không trả lời
With the following data, choose the appropriate diagram of disposition of tolerance zones for fit:
Select one:
a. Diagram 4.
b. Diagram 1.
c. Diagram 2.
d. Diagram 3.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 15/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 25
Không trả lời
Tolerances of diameters Ø77 and Ø105 of the connecting rod are not shown on the part drawing, so they can be specified as
follows:
Select one:
a. Ø77-0,046 and Ø105 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 16/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 26
Không trả lời
Choose proper dimensions for the outer diameter d of the sleeve bearing and stator bore D in a DC fan motor.
Select one:
a. d = Ø16 ; D = Ø16-0,018.
b. d = Ø16 ; D = Ø16+0,018.
c. d = Ø16 ; D = Ø16+0,018.
d. d = Ø16±0,0055 ; D = Ø16 .
Câu hỏi 27
Không trả lời
With a fit having , calculate the hole tolerance and shaft tolerance of the fit
Select one:
a. TD = 3μm ; Td = 19μm
b. TD = 30μm ; Td = 47μm
c. TD = 30μm ; Td = 19μm
d. TD = 33μm ; Td = 19μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 17/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 28
Không trả lời
Select a transition fit in which the probability of interference is a little bigger than the one of clearance when assembling at random.
Select one:
a. D = Ø80+0,030 ; d = Ø80 .
b. D = Ø80-0,030 ; d = Ø80 .
c. D = Ø80+0,030 ; d = Ø80 .
d. D = Ø80+0,030 ; d = Ø80±0,0095.
Câu hỏi 29
Không trả lời
In a transition fit, the maximum interference Nmax is calculated by the following formula:
Select one:
a. Nmax = EI - es.
b. Nmax = es - EI.
c. Nmax = ei - ES.
d. Nmax = ES - ei.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 18/19
10/20/23, 3:51 PM Review Chapter 1 (English) No score, only for practicing: Xem lại lần làm thử
Câu hỏi 30
Không trả lời
Select one:
a. D = Ø25-0,021 and d = Ø25 .
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=5096395&cmid=1147978 19/19