Professional Documents
Culture Documents
Test 1-2
Test 1-2
/ CHAPTER 2_Tolerances and Fits for Smooth parts / English Test 1 (including two chapters 1 and 2)
Câu hỏi 1
Sai
With the number of holes and shafts N = 10.000 pcs in the below transition fit, compare the probability of clearance and interference of the
fit.
Select one:
a. Probability of clearance is much bigger than probability of interference.
The correct answer is: Probability of clearance and probability of interference are approximately the same.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 1/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 2
Sai
Select all clearance fits in the basic hole system from the following ones.
Select one:
a. F7/h6 ; H7/g6.
b. H6/h5 ; H8/f7.
c. H7/g6 ; H6/h5.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 2/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 3
Đúng
Match diameters of hole and shaft in the two following columns in order to create two fits Ø45K7/h6 and Ø45H7/e7, respectively.
Select one:
a. 7 – e ; 2 – c.
b. 3 – e ; 2 – c.
c. 9 – e ; 2 – c. Your answer is
correct.
d. 9 – e ; 2 – a.
Câu hỏi 4
Đúng
Transition fits in the basic hole system are created by fundamental deviations as follows:
Select one:
a. From p to zc.
b. From P to ZC.
c. From J to N. Your answer is
correct.
d. From j to n.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 3/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 5
Sai
If fundamental deviation of a shaft is t and the shaft tolerance is Td , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by es = Td - ei Your answer is
incorrect
Câu hỏi 6
Sai
To increase the clearance of the fit F7/h6, one of the following fits will be selected:
Select one:
a. G7/h6 ; E8/h8 ; H7/e7
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 4/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 7
Đúng
With diameter Ø40, choose suitable limits of size for gear bore and shaft.
Select one:
a. Dmax = Ø40 ; Dmin = Ø39,975 and dmax = Ø40 ; dmin = Ø39,984.
d. Dmax = Ø40,025 ; Dmin = Ø40 and dmax = Ø40,018 ; dmin = Ø40,002. Your answer is
correct.
The correct answer is: Dmax = Ø40,025 ; Dmin = Ø40 and dmax = Ø40,018 ; dmin = Ø40,002.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 5/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 8
Đúng
With given holes having D = Ø110+0,035, choose the size of shafts d so that when assembled, it will create a transition fit having Smax =
32µm:
Select one:
a.
b. Your answer is
correct
c.
d.
Câu hỏi 9
Đúng
Select one:
a. D = Ø50+0,025; d = Ø50 .
b. D = Ø50 ; d = Ø50+0,025.
c. D = Ø50-0,025 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 6/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 10
Đúng
Choose proper dimensions for the outer diameter d of the sleeve bearing and stator bore D in a DC fan motor.
Select one:
a. d = Ø16±0,0055 ; D = Ø16 .
c. d = Ø16 ; D = Ø16-0,018.
d. d = Ø16 ; D = Ø16+0,018.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 7/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 11
Đúng
With the fits in the figures 1 and 2 below, calculate tolerance of the fits.
Figure 1
Figure 2
Select one:
a. Fig. 1: TS = 49µm. Fig. 2: TN = 41µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 8/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 12
Đúng
Select one:
a. Interference fit in the basic shaft system. Your answer is
correct
The correct answer is: Interference fit in the basic shaft system.
Câu hỏi 13
Đúng
Select one:
a. The same Nmax but the different Smax
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 9/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 14
Đúng
From the fit between the plain bearing and shaft on the assembly drawing, determine the limits of size of the bearing hole and shaft.
Select one:
a. Dmin = Ø40 , Dmax = Ø40,039 ; and dmin = Ø39,984 , dmax = Ø40.
c. Dmin = Ø40,025 , Dmax = Ø40,064 ; and dmin = Ø39,984 , dmax = Ø40. Your answer is
correct.
The correct answer is: Dmin = Ø40,025 , Dmax = Ø40,064 ; and dmin = Ø39,984 , dmax = Ø40.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 10/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 15
Đúng
Collect all transition fits in the basic shaft system from the following:
Select one:
a. M7/h6 ; Js7/h6 ; K7/h6 ; H7/h6.
Câu hỏi 16
Không trả lời
Select one:
a. D = Ø50 ; d = Ø50 .
b. D = Ø50 ; d = Ø50 .
c. D = Ø50+0,025 ; d = Ø50 .
d. D = Ø50-0,025 ; d = Ø50 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 11/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 17
Đúng
From the following fits, select one of which the clearance is the biggest:
Select one:
a. G6/h5
c. H8/n7
d. H8/f7
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 12/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 18
Đúng
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the E joint .
Select one:
a. Transition fit in the basic hole system.
The correct answer is: Clearance fit in the basic shaft system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 13/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 19
Sai
Select one:
a. D1 Your answer is
incorrect.
b. D2
c. D3
d. D4
Câu hỏi 20
Sai
With a given fit having D = Ø45-0,025 mm, d = Ø45-0,016mm, choose the correct answer
Select one:
a. Smax= 25μm and Nmax = 16μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 14/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 21
Sai
If fundamental deviation of a shaft is u and the shaft tolerance is Td , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by es = Td - ei
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 15/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 22
Đúng
Based on noticed working conditions of dimensions E in the below machine unit, suggest suitable limits of sizes.
Select one:
a. Dmin = Ø13,977 ; Dmax = Ø13,995 and dmin = Ø13,989 ; dmax = Ø14.
d. Dmin = Ø14,006 ; Dmax = Ø14,024 and dmin = Ø13,989 ; dmax = Ø14. Your answer is
correct.
The correct answer is: Dmin = Ø14,006 ; Dmax = Ø14,024 and dmin = Ø13,989 ; dmax = Ø14.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 16/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 23
Sai
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/f7 and B = Ø40H7/n6.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
b. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
c. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980. Your answer is
incorrect.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,17 ; d2max = Ø40,33.
d. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø40 ; D2max = Ø40,025 and d2min = Ø40,017 ; d2max = Ø40,033.
Câu hỏi 24
Sai
Based on the below figure, calculate limits of size of hole and shaft.
Select one:
a. Dmax = Ø64,949 ; Dmin = Ø64,979 and dmax = Ø65 ; dmin = Ø64,981.
b. Dmax = Ø64,079 ; Dmin = Ø46,049 and dmax = Ø65 ; dmin = Ø64,081. Your answer is
incorrect
The correct answer is: Dmax = Ø64,979 ; Dmin = Ø64,949 and dmax = Ø65 ; dmin = Ø64,981.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 17/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 25
Đúng
Choose the hole diameter of the pulley for assembling with surface Ø70 of the shaft.
Select one:
a. D = Ø70+0,015.
b. D = Ø70-0,030.
c. D = Ø70±0,15.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 18/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 26
Đúng
Select one:
a. Figure 1: P7/h6 ; Figure 2: H7/g6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 19/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 27
Đúng
Choose fit between worm gear bore and stepped shaft in a worm gear reducer.
Select one:
a. Ø40H7/k6. Your answer is
correct.
b. Ø40F7/h6.
c. Ø40K7/h6.
d. Ø40H7/f7.
Câu hỏi 28
Đúng
Select one:
a.
b.
c. Your answer is
correct
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 20/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 29
Sai
Select one:
a.
b.
c. Your answer is
incorrect
d.
Câu hỏi 30
Đúng
Among the following fits, select a transition fit, of which the probability of interference is the smallest :
Select one:
a. Js5/h4 Your answer is
correct.
b. N8/h7
c. M7/h6
d. H6/k5
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 21/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 31
Đúng
Suggest proper dimensions for worm gear bore D and stepped shaft d in a worm gear reducer.
Select one:
a. D = Ø40-0,025 and d = Ø40±008.
Câu hỏi 32
Sai
With given shafts having d = Ø110+0,019, choose the size of the holes D so that when assembled, it will create a transition fit in which the
probability of interference is greater than that of clearance.
Select one:
a.
b. Your answer is
incorrect
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 22/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 33
Đúng
Select one:
a. Probability of interference is about 80%.
The correct answer is: Probability of interference is slightly larger than probability of clearance.
Câu hỏi 34
Đúng
Select one:
a. Probability of interference is about 80%. Your answer is
correct.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 23/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 35
Đúng
Because of axial movement of tailstock spindle in hole Φ35 of the tailstock body, fit between spindle and hole can be selected as follows
Select one:
a. Φ35H6/h5. Your answer is
correct.
b. Φ35G6/h5.
c. Φ35H7/f7.
d. Φ35H6/n5.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 24/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 36
Đúng
Among the following fits, select a transition fit in the basic hole system, of which the probability of interference is the biggest:
Select one:
a. H8/s7
b. N8/h7
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 25/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
c. H8/n7 Your answer is
correct.
d. H6/k5
Câu hỏi 37
Sai
With given holes having D = Ø24+0,021, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of clearance is greater than that of interference.
Select one:
a. d = Ø24 . Your answer is
incorrect.
b. d = Ø24 .
c. d = Ø24±0,0065.
d. d = Ø24+0,013.
Câu hỏi 38
Sai
Because of hard machining holes D = Ø30 and shafts d = Ø30-0,010 in high precision fit, partial interchangeability is applied, i.c.,
expand hole and shaft tolerance three times, and then machined parts must be classified into corresponding groups for assembly.
Expanding dimensions of holes and shafts are:
Select one:
a. D = Ø30 ; d = Ø30-0,030.
b. D = Ø30 ; D = Ø30 .
d. D = Ø30 ; ; d = Ø30 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 26/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 39
Không trả lời
Match diameters of hole and shaft in the two following columns in order to create the transition fit having Nmax = 8μm.
Select one:
a. 2–b.
b. 2–d.
c. 3–a.
d. 4–b.
Câu hỏi 40
Không trả lời
Choose the type of fit for piston 1 and piston pin 2 of the internal combustion engine:
Select one:
a. Clearance fit or transition fit.
d. Transition fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 27/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4924753&cmid=1148002 28/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / English Test 1 (including two chapters 1 and 2)
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 1/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 1
Sai
Based on noticed working conditions of the below machine unit, suggest suitable fits for E and F of the components.
Select one:
a. H7/js6 for E; H7/s6 for F. Your answer is
incorrect.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 2/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 2
Sai
Select one:
a. Diagram 2.
b. Diagram 4.
c. Diagram 3.
Câu hỏi 3
Sai
Sort the following fits in ascending order of clearance (if they have the same nominal size):
Select one:
a.
b. Your answer is
incorrect.
c.
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 3/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 4
Đúng
In the below reducing gearbox, fits for the fixed joints between gears and shafts can be choosen as follows :
Select one:
a. H7/k6 or H6/k5 Your answer is
correct
b. H6/h5 or H7/f6.
c. H7/k6 or H6/g5.
d. H6/h5 or H7/n6.
Câu hỏi 5
Đúng
With a fit having , calculate the hole tolerance and shaft tolerance of the fit
Select one:
a. TD = 3μm ; Td = 19μm
c. TD = 33μm ; Td = 19μm
d. TD = 30μm ; Td = 47μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 4/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 6
Đúng
With two given fits Ø36H8/k7 and Ø36H7/s6, select the correct sentence.
Select one:
a. The minimum limits of the shafts in 2 fits are the same.
c. The minimum limits of the holes in 2 fits are the same. Your answer is
correct.
The correct answer is: The minimum limits of the holes in 2 fits are the same.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 5/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 7
Sai
Choose the type of fit for the rolling bearing 26 and shaft I of the below reduction gearbox.
Select one:
a. Clearance fit with very small clearance amount. Your answer is
incorrect.
b. Transition fit.
The correct answer is: Interference fit with very small interference amount.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 6/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 8
Đúng
........................... is the algebric difference between the minimum limit of size and the nominal size.
Select one:
a. Limits of size
d. Tolerance
Câu hỏi 9
Sai
Select one:
a. One of two limiting deviations (either the upper or lower deviation) which is the farthest one to zero line . Your answer is
incorrect.
b. One of the two limiting deviations (either the upper or lower deviation) which is the nearest one to zero line.
c. either the hole upper or shaft lower deviation which is the nearest one to zero line.
d. either the upper or lower deviation of a size.
The correct answer is: One of the two limiting deviations (either the upper or lower deviation) which is the nearest one to zero line.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 7/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 10
Đúng
Match diameters of hole and shaft in the two following columns in order to create all transition fits in the basic shaft system.
Select one:
a. 3 – e ; 9 – e ; 10 – e.
b. 3 – e ; 6 – e ; 10 – e.
c. 3 – e ; 6 – e ; 9 – e ; 10 – e. Your answer is
correct.
d. 3 – e ; 6 – c ; 9 – c ; 10 – e.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 8/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 11
Đúng
Choose proper diameter of the pulley hole in order assemble with the shaft diameter Ø70 of below part.
Select one:
a. Ø70+0,030. Your answer is
correct.
b. Ø70 .
c. Ø70-0,030.
d. Ø70±0,030.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 9/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 12
Sai
Select one:
a. Probability of interference is slightly larger than probability of clearance.
The correct answer is: Probability of interference is slightly larger than probability of clearance.
Câu hỏi 13
Sai
With a given fit having D = d = Ø28, TD = 21μm, Nmin = 7μm, es = 0, Nmax= 41μm, determine the limits of size of the hole and the shaft.
Select one:
a. Dmax = Ø27,98 ; Dmin = Ø27,959 ; dmax = Ø28 ; dmin = Ø27,987
d. Dmax = Ø27,80 ; Dmin = Ø27,59 ; dmax = Ø28 ; dmin = Ø27,987 Your answer is
incorrect.
The correct answer is: Dmax = Ø27,98 ; Dmin = Ø27,959 ; dmax = Ø28 ; dmin = Ø27,987
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 10/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 14
Đúng
From the assembly drawing, determine dimensions of the components in the machine cluster as follows:
Select one:
a. Φ55-0,030 : hole diameter of the part 3 ; Φ55-0,030 : hole diameter of the part 1 ; Φ55±0,0095 : diameter of the shaft 2.
b. Φ55-0,030 : hole diameter of the part 3 ; Φ55+0,030 : hole diameter of the part 1 ; Φ55-0,019 : diameter of Your answer is
the shaft 2. correct.
c. Φ55 : hole diameter of the part 3 ; Φ55+0,030 : hole diameter of the part 1 ; Φ55-0,019 : diameter of the shaft 2.
d. Φ55 : hole diameter of the part 3 ; Φ55+0,030 : hole diameter of the part 1 ; Φ55 : diameter of the shaft 2.
The correct answer is: Φ55-0,030 : hole diameter of the part 3 ; Φ55+0,030 : hole diameter of the part 1 ; Φ55-0,019 : diameter of the shaft 2.
Câu hỏi 15
Sai
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/f7 and B = Ø42H7/m6.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,09 ; d2max = Ø42,25.
b. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
c. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,979 ; d1max = Ø30. Your answer is
incorrect.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
d. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,959 ; d1max = Ø29,980.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 11/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 16
Đúng
Choose the hole diameter of the pulley for assembling with surface Ø70 of the shaft.
Select one:
a. D = Ø70±0,015.
b. D = Ø70-0,03.
c. D = Ø70+0,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 12/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 17
Sai
Select one:
a. Ø10±0,11.
c. Ø10±0,011.
d. Ø10+0,015.
Câu hỏi 18
Đúng
In order to determine the shaft diameter d = Ø20 in the below part drawing, fit between the pulley hole and the shaft must be:
Select one:
a. Ø20K7/h6.
b. Ø20K7/k6.
c. Ø20H7/h6.
Câu hỏi 19
Đúng
Select one:
a. The same Smax and Smin
The correct answer is: The same Smin but the different Smax
Câu hỏi 20
Đúng
Choose the dimensions for piston d and cylinder D of an internal combustion engine:
Select one:
a. D = Ø80±0,0065 and d = Ø80-0,008
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 14/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 21
Đúng
Select one:
a. D = Ø120 ; d = Ø120-0,047. Your answer is
correct
b. D = Ø120-0,047 ; d = Ø120 .
c. D = Ø120 ; d = Ø120±0,027.
d. D = Ø120 ; d = Ø120 .
Câu hỏi 22
Sai
With two given fits Ø50H6/g5 and Ø50G6/h5, select the wrong sentence.
Select one:
a. The two hole tolerances are the same. Your answer is
incorrect.
b. The minimum limit for the hole in the first fit is equal to the maximum limit of size for the shaft in the second fit.
c. The shaft upper deviation in the first fit is equal to the hole lower deviation in the second fit.
The correct answer is: The shaft upper deviation in the first fit is equal to the hole lower deviation in the second fit.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 15/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 23
Đúng
Select a transition fit in which the probability of interference is a little bigger than the one of clearance when assembling at random.
Select one:
a. D = Ø80-0,030 ; d = Ø80 .
b. D = Ø80+0,030 ; d = Ø80±0,0095.
c. D = Ø80+0,030 ; d = Ø80 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 16/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 24
Đúng
Based on noticed working conditions of the below machine unit, suggest suitable fits for the components.
Select one:
a. N7/h6 for E ; G7/h7 for F.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 17/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 25
Đúng
Choose suitable shaft diameter in order to assemble with the hole Ø50 of the wormwheel
Select one:
a. Ø50±0,015.
b. Ø50 .
c. Ø50-0,013.
Câu hỏi 26
Sai
To increase the interference of the fit H7/s6, one of the following fits will be selected:
Select one:
a. H7/t6 ; H7/s7 ; H7/u7.
Câu hỏi 27
Đúng
From the assembly drawing, determine dimensions of pin 2 and two holes of body 1 in the roller pulley wheel unit.
Select one:
a. Ø12+0,027 is hole diameter of body 1 and Ø12 is diameter of pin 2.
b. Ø12-0,027 is hole diameter of body 1 and Ø12-0,018 is diameter of pin 2. Your answer is
correct.
The correct answer is: Ø12-0,027 is hole diameter of body 1 and Ø12-0,018 is diameter of pin 2.
Câu hỏi 28
Đúng
With given shafts having d = Ø110-0,021, choose the size of the holes D so that when assembled, it will create a clearance fit having Smax =
46µm.
Select one:
a.
b.
c. Your answer is
correct
d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 19/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 29
Đúng
Select one:
a. Ø45H7/r6.
b. Ø45P7/h6.
d. Ø45H7/p6.
Câu hỏi 30
Đúng
Select one:
a. 46μm
b. 64μm
c. 74μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 20/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 31
Sai
In order to create transition fit between driven pulley and shaft portion of Ø25 diameter with Smax = 19 µm and Nmax = 15 µm, pulley bore
must be:
Select one:
a. D = Ø25+0,21.
c. D = Ø25+0,021.
d. D = Ø25±0,021.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 21/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 32
Sai
Basic hole in the basic hole system is the one that has:
Select one:
a. the upper and lower limiting deviations is positive.
b. the upper and lower limiting deviations is negative.
c. the lower limiting deviation is 0
d. the upper limiting deviation is 0 Your answer is
incorrect.
Câu hỏi 33
Đúng
Select one:
a. H7/f7
b. F7/h6
c. H7/r6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 22/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 34
Sai
Choose the proper diameter d of pin 1 assembled with body hole D of "a Cardan universal coupling".
Select one:
a. d = Ø16 ; D = Ø16-0,018.
b. d = Ø16 ; D = Ø16 .
d. d = Ø16-0,011 ; D = Ø16 .
Câu hỏi 35
Sai
Select one:
a. From 12 -> 18.
b. From 01 -> 4.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 23/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 36
Đúng
Select one:
a. D = Ø75 mm ; d = Ø75- 0,019 mm
Câu hỏi 37
Đúng
Select one:
a. from nominal size to minus.
b. fully below the zero line.
c. equally disposed about the zero line.
d. fully above the zero line. Your answer is
correct.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 24/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 38
Đúng
Match diameters of hole and shaft in the two following columns in order to create the fit Ø45G7/h6.
Select one:
a. 8 – e.
b. 2 – d.
c. 4 – e. Your answer is
correct.
d. 7 – e.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 25/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 39
Sai
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the B joint .
Select one:
a. Transition fit in the basic hole system.
The correct answer is: Transition fit in the basic hole system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 26/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 40
Sai
Match diameters of hole and shaft in the two following columns in order to create all transition fits in the basic hole system.
Select one:
a. 2 – b ; 2 – d ; 2 – g ; 2 – h.
b. 2 – b ; 2 – c ; 2 – e ; 2 – f ; 2 – h.
c. 2 – b ; 2 – d ; 2 – e ; 2 – g ; 2 – h. Your answer is
incorrect.
d. 2 – b ; 2 – d ; 2 – f ; 2 – i.
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4922737&cmid=1148002 27/27
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
/ CHAPTER 2_Tolerances and Fits for Smooth parts / English Test 1 (including two chapters 1 and 2)
Câu hỏi 1
Đúng
Match diameters of hole and shaft in the two following columns in order to create all clearance fits in the basic shaft system.
Select one:
a. 2 – e ; 4 – e ; 8 – e. Your answer is
correct.
b. 4 – e ; 8 – e.
c. 2 – e ; 3 – e ; 8 – a.
d. 3 – e ; 10 – g.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 1/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 2
Đúng
Disposition diagrams of the tolerance position in the below picture belong to the following fits in respectively:
Select one:
a. H7/js7 ; K8/h7 ; H7/n7 ; R7/h6
b. H7/js7 ; K8/h7 ; R7/h6 ; H7/n7 Your answer is
correct.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 2/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 3
Sai
From the chosen fit between the outer diameter of the plain bearings and the holes of Ø16 in the below part drawing, determine the hole
diameter D of the part holes and outer diameter d of the plain bearings.
Select one:
a. D = Ø16±0,009 ; d = Ø16±0,011.
b. D = Ø16±0,009 ; d = Ø16 .
d. D = Ø16+0,018 ; d = Ø16 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 3/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 4
Sai
Choose a transition fit that the interference probability of which is about 80%
Select one:
a. Ø50H7/n6
b. Ø50H7/m6
d. Ø50H7/js6
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 4/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 5
Đúng
In order to get dimensions Ø25 and Ø36 on the part drawing, tolerance zones of these diameters must be:
Select one:
a. Ø25k6 and Ø36k7.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 5/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 6
Đúng
With a given fit having D = Ø50 and d = Ø50 mm, calculate Smax , Smin , Nmax , Nmin of the fit.
Select one:
a. Smax = 50µm ; Smin = 16µm ; Nmin = 0 ; Nmax = 5µm.
b. Smax = 50µm ; Smin = Nmin = 0 ; Nmax = 5µm. Your answer is
correct.
The correct answer is: Smax = 50µm ; Smin = Nmin = 0 ; Nmax = 5µm.
Câu hỏi 7
Đúng
Determine suitable limits of sizes for two fits of the dimensions A = Ø30H7/g6 and B = Ø42H7/m6.
Select one:
a. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
b. Fit of dimension A: D1min = Ø30,007 ; D1max = Ø30,028 and d1min = Ø29,987 ; d1max = Ø30.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
c. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993. Your answer is
correct.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
d. Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,09 ; d2max = Ø42,25.
The correct answer is: Fit of dimension A: D1min = Ø30 ; D1max = Ø30,021 and d1min = Ø29,980 ; d1max = Ø29,993.
Fit of dimension B: D2min = Ø42 ; D2max = Ø42,025 and d2min = Ø42,009 ; d2max = Ø42,025.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 6/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 8
Sai
Tolerances of diameters d1 = Ø30 and d2 = Ø50 of the shaft are not shown on the part drawing, so they can be specified as follows:
Select one:
a. d1min = Ø29,067 ; d1max = Ø30 and d2min = Ø49,061 ; d2max = Ø50.
b. d1min = Ø29,835 ; d1max = Ø30,165 and d2min = Ø49,805 ; d2max = Ø50,195. Your answer is
incorrect.
The correct answer is: d1min = Ø29,67 ; d1max = Ø30 and d2min = Ø49,61 ; d2max = Ø50.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 7/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 9
Sai
Choose the suitable hole of pulley in order to assemble with the shaft diameter d = Ø20 in the part drawing:
Select one:
a. D = Ø20±0,010. Your answer is
incorrect
b. D = Ø20+0,021.
c. D = Ø20+0,21.
d. D = Ø20-0,021.
Câu hỏi 10
Đúng
With a given fit of D = Ø42 and d = Ø42 , reselect the hole so that the average of interference equals to 17μm.
Select one:
a. Ø42 . Your answer is
correct
b. Ø42+0,025.
c. Ø42 .
d. Ø42 .
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 8/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 11
Sai
Based on the technical requirements, the limiting deviations of the part length 165 can be defined from the dimension:
Select one:
a. 165js13.
b. 165k6.
d. 165H13.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 9/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 12
Đúng
Select all transition fits in the basic shaft system from the following ones:
Select one:
a.
b. Your answer is
correct.
c.
d.
Câu hỏi 13
Sai
With given holes having D = Ø120+0,035, choose the size of the shafts d so that when assembled, it will create a transition fit in which the
probability of clearance is greater than that of interference.
Select one:
a. d = Ø120±0,011.
c. d = Ø120 .
d. d = Ø120+0,022.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 10/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 14
Sai
To increase the clearance of the fit Ø42H7/f7, the following fit will be selected:
Select one:
a. Ø42H7/e7 or Ø42H8/f7.
b. Ø42H7/e7 or Ø42F8/h7.
d. Ø42H7/h6 or Ø42G7/h6.
Câu hỏi 15
Đúng
From the fit Ø30N8/h7 on assembly drawing, determine limits of sizes of hole and shaft.
Select one:
a. Dmin = Ø29,979 ; Dmax = Ø30 and dmin = Ø29,964 ; dmax = Ø29,997.
b. Dmin = Ø29,964 ; Dmax = Ø29,997 and dmin = Ø29,979 ; dmax = Ø30. Your answer is
correct.
The correct answer is: Dmin = Ø29,964 ; Dmax = Ø29,997 and dmin = Ø29,979 ; dmax = Ø30.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 11/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 16
Sai
Choose a series of holes for assembling the following shafts Φ30 in order to create a clearance fit with the average clearance Stb =
23,5μm.
Select one:
a. D = Ø30
b. D = Ø30
d. D = Ø30+0,016
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 12/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 17
Sai
From the fit between the plain bearing and the shaft on the assembly drawing, if shaft dimension is d = Ø40-0,016 , bearing bore should be:
Select one:
a. D = Ø40-0,039. Your answer is
incorrect
b. D = Ø40±0,019.
c. D = Ø40+0,039.
d. D = Ø40 .
Câu hỏi 18
Đúng
If fundamental deviation of a shaft is g and the shaft tolerance is Td , non-fundamental deviation is:
Select one:
a. upper limiting deviation that is determined by es = Td + ei
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 13/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 19
Sai
Choose proper diameters of the fit between sleeve bearing bore D and motor shaft d in a DC fan.
Select one:
a. D = Ø20+0,021 ; d = Ø20 .
c. D = Ø20+0,21 ; d = Ø20 .
d. D = Ø20+0,021 ; d = Ø20 .
Câu hỏi 20
Sai
Among the following fits, select one in the basic hole system, of which the clearance is the biggest (if they have the same nominal size):
Select one:
a. E9/h8.
c. H8/e8.
d. H7/f7.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 14/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 21
Sai
With two given fits Ø36H7/g6 and Ø36H8/k7, select the correct sentence.
Select one:
a. The minimum limits of the holes in 2 fits are the same.
b. The maximum limits of the shafts in 2 fits are the same. Your answer is
incorrect.
The correct answer is: The minimum limits of the holes in 2 fits are the same.
Câu hỏi 22
Sai
Choose the suitable hole of sleeve (used to prevent the axial movement of the gear) in order to assemble with the shaft diameter d = Ø30
in the part drawing.
Select one:
a. D = Ø30±0,026.
c. D = Ø30+0,052.
d. D = Ø30+0,52.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 15/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 23
Sai
A fit in the basic shaft system with TD = 40μm, Smax = 55μm and hole fundamental deviation JS. Determine limiting deviations of the hole
and shaft
Select one:
a. ES = 20μm, EI = -20μm, es = 0μm, ei = -35μm
Câu hỏi 24
Đúng
Select one:
a. fully above the zero line.
b. from nominal size to minus.
c. fully below the zero line. Your answer is
correct.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 16/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 25
Sai
Select all interference fits in the basic shaft system from the following ones.
Select one:
a. H8/u8 ; S7/h6. Your answer is
incorrect.
b. S7/h6 ; U8/h7.
c. U8/h7.
d. H8/u8 ; H7/r6.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 17/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 26
Sai
Based on noticed working conditions of the below machine unit, suggest suitable type of fit for the C joint .
Select one:
a. Clearance fit in the basic shaft system.
The correct answer is: Transition fit in the basic hole system.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 18/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 27
Sai
Select the correct sentence from two fits Ø35H7/r6 and Ø120R7/h6:
Select one:
a. the lower limiting deviations of 2 shafts are the same.
b. the lower limiting deviation of the first hole is equal to the upper limiting deviation of the second shaft.
c. the upper limiting deviations of 2 holes are the same. Your answer is
incorrect.
d. the upper limiting deviation of the first hole is equal to the lower limiting deviation of the second shaft.
The correct answer is: the lower limiting deviation of the first hole is equal to the upper limiting deviation of the second shaft.
Câu hỏi 28
Đúng
From the fit between the pulley 7 and the shaft 2 on the assembly drawing, determine the limits of size of the hole and shaft.
Select one:
a. Dmin = Ø28 , Dmax = Ø28,021 ; and dmin = Ø28,002 , dmax = Ø28,015. Your answer is
correct.
The correct answer is: Dmin = Ø28 , Dmax = Ø28,021 ; and dmin = Ø28,002 , dmax = Ø28,015.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 19/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 29
Sai
Match diameters of hole and shaft in the two following columns in order to create the interference fit having the average interference Ntb =
54,5μm.
Select one:
a. 1–b.
c. 3–b.
d. 1–d.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 20/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 30
Sai
With the fits in the figures 1 and 2 below, choose the correct answer.
Figure 1
Figure 2
Select one:
a. Figure 1: the average clearance Stb = 29,5µm ; Figure 2: the average interference Ntb = 24,5µm.
b. Figure 1: the average clearance Stb = 26,5µm ; Figure 2: the average interference Ntb = 29,5µm.
c. Figure 1: the average clearance Stb = 31,5µm ; Figure 2: the average interference Ntb = 26,5µm. Your answer is
incorrect
d. Figure 1: the average clearance Stb = 29,5µm ; Figure 2: the average interference Ntb = 26,5µm.
The correct answer is: Figure 1: the average clearance Stb = 29,5µm ; Figure 2: the average interference Ntb = 26,5µm.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 21/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 31
Đúng
Select one:
a. Clearance fits and Interference fits
c. Interference fits
d. Clearance fits
Câu hỏi 32
Sai
Choose the suitable type of fits for the joints of the below machine unit:
Select one:
a. Clearance fit for the joint between item 1 and 2 as well as the joint between item 3 and 2. Your answer is
incorrect.
b. Clearance fit for the joint between item 1 and 2 ; Transition fit for the joint between item 3 and 2.
c. Interference fit for the joint between item 1 and 2 ; Clearance fit for the joint between item 3 and 2.
d. Transition fit for the joint between item 1 and 2 ; Clearance fit for the joint between item 3 and 2.
The correct answer is: Clearance fit for the joint between item 1 and 2 ; Transition fit for the joint between item 3 and 2.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 22/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 33
Sai
Fit for a joint between a idler gear and a shaft can be choosen as follows:
Select one:
a.
b. Your answer is
incorrect.
c.
d.
Câu hỏi 34
Đúng
With a fit having D = Ø42±0,012 and d = Ø42-0,016, c alculate the tolerance of the fit.
Select one:
a. 40μm Your answer is
correct
b. 33μm
c. 28μm
d. 24μm
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 23/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 35
Đúng
Among the following fits, select a transition fit in the basic shaft system, of which the probability of interference is the biggest:
Select one:
a. M7/h6
c. Js5/h4
d. H6/k5
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 24/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 36
Đúng
The limits of size of the slot b = 10±0,011 on the detail drawing are:
Select one:
a. bmin= 9,890 ; bmax= 10,011.
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 25/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 37
Sai
With two given fits Ø45M7/h6 and Ø45H7/m6, select the wrong sentence.
Select one:
a. The maximum limit of size for the shaft in the first fit is equal to the minimum limit for the hole in the second fit.
c. Smax and Nmax of two fits are the same. Your answer is
incorrect.
d. The hole upper deviation in the first fit is equal to the shaft lower deviation in the second fit.
The correct answer is: The hole upper deviation in the first fit is equal to the shaft lower deviation in the second fit.
Câu hỏi 38
Sai
Select one:
a. Smax = 0,033 ; Nmax = 0,008. Your answer is
incorrect
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 26/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Câu hỏi 39
Sai
Choose suitable diameters of the gear hole 4 and the counter shaft in the speed gearbox.
Select one:
a. D = Ø42 and d = Ø42-0,016.
Câu hỏi 40
Sai
Select one:
a. From P (p) to ZC (zc).
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 27/28
10/20/23, 4:13 PM English Test 1 (including two chapters 1 and 2): Xem lại lần làm thử
Chuyển tới...
https://fhqx.hcmute.edu.vn/mod/quiz/review.php?attempt=4918132&cmid=1148002 28/28