Professional Documents
Culture Documents
FusionServer Pro 2288X V5 Server V100R005 Quick Start Guide 01
FusionServer Pro 2288X V5 Server V100R005 Quick Start Guide 01
1 2 3
No. Indicator Description Remarks No. Indicator Description Remarks Run the ipmcset -d powerstate -v 1 command on the iBMC CLI.
Steady yellow: The server is ready to status Blinking green: Data is being Click the power control button on the iBMC WebUI.
power on. indicator/data transmitted. For details, see the FusionServer Pro Rack Server iBMC User Guide.
Power button: transmission Steady green: The network port is
6 Error Codes
When the server is powered on, you status indicator properly connected.
can press the power button to shut
down the OS. Error Code Fault Description Remarks
When the server is powered on, 4 Installation --- The server is operating normally. -
holding down the power button for 6 C0X CPU X is abnormal or faulty. X indicates the CPU number.
seconds will forcibly power off the
XXX indicates the DIMM
server. XXX DIMM XXX is abnormal or faulty.
When the server is ready to be Before unpacking and installing the server, wear an ESD wrist strap or gloves to avoid number.
damage to electrostatic-sensitive parts. A00 Air inlet overheating -
powered on, you can press the power
button to start the server. At least two people are required to handle the server during installation or removal. A0X
The temperature of CPU X exceeds its X indicates the CPU number.
normal range.
Indicators and buttons on the rear panel 1. Install the server into the cabinet.
P0X PSU X is abnormal or faulty. X indicates the PSU number.
No. Indicator Description Remarks (1) Place the server on the guide rails and push it into the cabinet.
6/9 PSU indicator Off: No power is supplied. Replace the PSU if X indicates the fan module
(2) Align the server mounting ears with the cabinet mounting bars, and tighten the F0X Fan module X is abnormal or faulty.
Blinking green at 1 Hz: the indicator is in number.
captive screws on the mounting ears.
The input is normal, and the any of the b01 The power supply to the mainboard is -
server is standby. following states: abnormal.
The input is overvoltage or Blinking green b02 The RAID controller card is abnormal or -
undervoltage. at 1 Hz after faulty.
The PSU is in deep the server is L01 The cable is not securely or correctly -
hibernation mode. powered on connected.
Blinking green at 4 Hz: An online Steady orange E01 The CMOS battery is abnormal. -
firmware upgrade is being HXX The drive in slot XX is abnormal or faulty. XX indicates the drive
performed. number.
Steady green: The power input and
The variable X in this table is an Arabic numeral.
output are normal.
Steady orange: The power input is
normal but no power output is 7 Follow-up
supplied.
After the server is successfully powered on, configure the server. For details, see the
NOTE
FusionServer Pro 2288X V5 Server V100R005 User Guide.
The possible causes are as follows:
To obtain the user guide:
Overheat protection Scan the QR code.
Overcurrent or short circuit Visit https://e.huawei.com.
protection
Output overvoltage protection
Short circuit protection
2. Connect cables to service and management network ports.
Failures of some components
12 UID indicator The UID indicator is used to pinpoint None 8 Hazardous Substance Statement for Electronic
the server to be operated.
Off: The server is not being and Electrical Products
located. Hazardous Substances
Blinking blue: The server is Part
3. Connect the power cables. Cd Pb Hg Cr (VI) PBBs PBDEs
distinguished from other servers Chassis ○ × ○ ○ ○ ○
that have also been located. ○ × ○ ○ ○ ○
Steady blue: The server is being
PCBA
located. Cables ○ × ○ ○ ○ ○
NOTE Equipment ○ × ○ ○ ○ ○
You can press the UID button or use Accessories ○ × ○ ○ ○ ○
iBMC CLD to turn on or off the UID This statement for electronic and electrical products complies with SJ/T 11364.
indicator. ○: indicates that the hazardous substance contained in all of the homogenous materials for
14 Connection Off: The network port is not None this part is below the limit specified in GB/T 26572.
status indicator connected. ×: indicates that the hazardous substance contained in at least one of the homogenous
of the Steady green: The network port is
materials for this part is above the limit specified in GB/T 26572.
management properly connected.
network port
16 Data Off: No data is being transmitted. None
transmission Blinking yellow: Data is being
status indicator transmitted.
of the
management
network port
21 10GE optical Off: The network port is not None
port connected.
transmission Steady green: The data 5 Power-On
rate indicator transmission rate is 10 Gbit/s. Power on the server using any of the following methods:
Steady yellow: The data
If the PSUs are installed but not yet powered on, powered on the PSUs. The server will be
transmission rate is lower than 10 powered on with the PSUs.
Gbit/s. If the PSUs are powered on and the server is on standby, press the power button on the
23 10GE optical Off: The network port is not None front panel.
port connection connected. Power on the server using the IBMC.
4 5 6