Professional Documents
Culture Documents
IP2315 Datasheet v1.0.zh-CN - en
IP2315 Datasheet v1.0.zh-CN - en
com
IP2315
Single-cell lithium battery synchronous switch buck with integrated input fast charge protocol4.8AChargeIC
characteristic
Overview
- Input voltage range5V~12V
- Maximum charging current at battery end4.8A@9V/2AInput and IP2315It is an integratedMOSEfficient synchronous buck conversion
- output battery voltageVSETThe pin can be set charging with input fast charging protocolIC.
(4.2V/4.35V/4.4V/4.5V) recharging currentISETPin can be
IP2315Input voltage range5V~12V;IP2315integrated Type-C PD, Huawei
- set (set the input current) PowerMOSIntegrated built-in
FCP, SamsungAFC,MTK PE+1.1/2.0 input fast charging protocol, you can apply
-
to the adapter9Vor12Vvoltage to reduce charging time;IP2315accessibleISET
- High-efficiency synchronous buck charging:
pin sets the input charging current, the input9V/2AWhen, the maximum
94%,VIN=5V,BAT=3.7V,IBAT=4A 93.5%,VIN=9V,
BAT=3.7V,IBAT=4A 93%,VIN=12V,BAT=3.7V,IBAT=4A charging current at the battery end3.7V/4.8A;IP2315It is compatible with small
supportType-C PDEnter the fast charging protocol current adapters. When the adapter’s output load capacity is insufficient, it can
ledNumber of lights
off level500kHz.
- Bluetooth Speaker,POSmachine,e-cigarette
11
12
13
14
15
18
19
6
7
VSYS LX BST
BAT
twenty two
20 Charger driver
VIN twenty one
8
CC1 VIN LED1
CC2 VBAT
DM LED2 9
TYPE-C
DP
GND
2 CC1 IP2315 LED3 10
3 CC2
DM
twenty three
DP
twenty four
1
4 D1
5
25
28 D2
29
30
EPAD
RVSET
27
26
16
R1
RICHG RNTC
82K DH
ICHGSET
GND
NTC
NC
NC
NC
NC
NC
32 31 30 29 28 27 26 25
NC 1 twenty four
DP
NC 4 VIN
twenty one
IP2315
NC 5 20 VIN
VSYS 6 19 VSYS
VSYS 7 18 VSYS
LED1 8 17 GND
9 10 11 12 13 14 15 16
LED3
HLED
LED2
BST
LX
LX
LX
LX
1,4,5,25, 28,29,
NC hanging in the air
30,32
2 CC1 USB Type-CDetect pinCC1
6,7,18,19 VSYS Input the intermediate node and need to connect a capacitor
twenty two BAT Battery voltage detection pin, connected to the positive terminal of the battery
33(EPAD) GND Power ground and heat dissipation ground need to be kept consistent withGNDgood contact
* Stresses greater than those listed in the Absolute Maximum Ratings section may cause permanent damage to the device under any Absolute Maximum Rating conditions.
Excessive exposure time may affect the reliability and service life of the device.
* Beyond these operating conditions, device operating characteristics are not guaranteed.
4.Electrical characteristics
smallest maximum
parameter symbol Test Conditions Typical value unit
value value
VBAT=3.7V,VIN=5V,ICHG=4A 94 %
VBAT=3.7V,VOUT=9V,ICHG=4A
93.5 %
Charging conversion efficiency n
VBAT=3.7V,VOUT=12V,ICHG=4A
93 %
5.Function description
IP2315It has a constant current and constant voltage lithium battery charging management system that supports synchronous switching structure. Can automatically match different charging voltage
specifications.
When the battery voltage is less than3Vwhen, adopt250mATrickle charging; when the battery voltage is greater than3V, enter the input constant current charging, charge with the
set constant current charging current; when the battery voltage is close to the set battery voltage, enter the constant voltage charging; when the battery terminal charging current is less
than300mAWhen the battery voltage is close to the constant voltage, charging will stop. After charging is completed, if the battery voltage is lower than4.1V Then, turn on battery charging
again.
IP2315It will automatically adjust the charging current to adapt to adapters with different load capabilities.
IP2315Integrated input fast charging protocol, supportType-C PD, HuaweiFCP, SamsungAFC,MTK PE+1.1/2.0The input fast charging protocol can apply
IP2315It has perfect protection function. The built-in soft-start function prevents faults caused by excessive inrush current during startup, and integrates input overvoltage, undervoltage, overtemperature and
other protection functions to ensure stable and reliable operation of the system.
- IP2315integratedVINInput undervoltage protection,VINThe input loop will automatically adjust the charging current whenIP2315After detecting that the input voltage is too low, the charging current
will be reduced to ensure that the adapter will not be pulled to death.
-IP2315integratedVINInput overvoltage protection, whenIP2315After detecting that the input voltage is too high, charging will be stopped.
- IP2315integratedNTCTemperature protection function, withNTCthermistor, when the temperature is detected at0~55charge normally when the temperature is within the temperature range; when
-IP2315Integrated charging timeout protection: when charging time exceedstwenty fourAfter hours, charging will be forcibly stopped.
- IP2315Integrated over-temperature protection function: whenIP2315It is detected that the chip temperature reaches135℃, charging will stop; when the temperature drops to85℃,
IP2315Only then do you think the temperature has returned to normal and start charging again;
IP2315Supported byLED3(No.10pin), connect pull-down resistors of different values to select the corresponding battery type, which is related toLED3Display output
multiplexing:
LED3(No.10pin) pull-down resistor onRVSET Battery type selection (battery full voltage)
10K 4.5V
68K 4.4V
120K 4.35V
NC 4.2V
IP2315Can be accessed byICHGSET(No.27pin) to set the constant current charging current (input terminal current), the external
51K 500mA
130K 1000mA
180K 1500mA
> 300K(NC) 2000mA
ChargeNTC
IP2315supportNTCprotection function, throughNTCThe pin detects the battery temperature. When the detected temperature exceeds the set temperature, it turns offcharger.
20uA device
LT
VL=1.32v
R2 RNTC
If measuredNTC pinThe upper voltage is higher than1.32v, it means the battery temperature is too low
If measuredNTC pinThe upper voltage is lower than0.43v, it means the battery temperature is too high
NTCblock diagram
- whenNTCThe temperature is detected at0~55Charge normally within the range. When the temperature is higher than55degree, or lower than0degree, stop charging.
- if not neededNTCfunction, you canNTCuse51Kresistor to ground,NTCThe pin cannot be left floating, otherwise it may cause abnormal charging.
- fromNTCrelease20uAcurrent,NTCConnect an external resistor toGND, The voltage drop produced by this current across the resistor is used to determine the temperature range.
- 20 1.52
- 15 1.49
- 10 1.44
0 1.32
43 0.60
45 0.56
50 0.49
55 0.43
60 0.38
65 0.33
Chargeledinstruct
IP2315It can flexibly support one or two battery indicator lights. Through the built-in intelligent recognition algorithm, it can automatically identify several external
L3
VSET
L2
D1 D2
L1 VBAT+
10k
2 light mode
L3
VSET
L2
10k
10k
L1
1 light mode
I2C
VBAT
INT 10
2K2 2K2
MCU IP2315
SCL 8
SDA
9
I2CMode maximum support400Kbps,8bitregister address,8bitRegister data, both sending and receiving are high-end
SCLK
SDA
I2C WRITE
from0x05Register read back data
SCLK
SDA
Slave address 0xEA Register address 0x05 Slave address 0xEB Data 0x5A
Start sACK sACK sACK
mNACK Stop
Restart
I2C Read
Special instructions: inI2CRead the end of the data, at the lastBYTEAfter reading, be sure to giveNACKsignal, otherwiseIP2315
would thinkMCUStill need to continue reading data, nextSCLKThe next data will be output and cannot be received normally. STOP
* ReservedThe registers cannot be arbitrarily written with data, and the original values cannot be changed, otherwise unpredictable results will occur. Operations on registers must be
carried out according to read-modify-write, and only the ones to be used are modified.bit, other unused ones cannot be modifiedbitvalue.
SYS_CTL1
Register address =0x01
Bit(s) Name Description R/W
7:1 Reserved
0 ChargechargerEnable R/W
0:disable
1:enable
ICHSET_CTL
Register address =0x1E
Bit(s) Name Description R/W
7:6 Reserved
5:3 ICHGSETPin setting charging current (input current) R/W
000:disable, set the charging current through the register
2:0 Reserved
CHG_ISET_5V
CHG_ISET_7V
Register address =0x28
Bit(s) Name Description R/W
7 Reserved
6:0 ISET set up7VCharging current at input (input terminal current) R/W
Ichg=ISET*0.025A
CHG_ISET_9V
Register address =0x29
Bit(s) Name Description R/W
7 Reserved
6:0 ISET set up9VCharging current at input (input terminal current) R/W
Ichg=ISET*0.025A
CHG_ISET_12V
Register address =0x2A
Bit(s) Name Description R/W
7 Reserved
6:0 ISET set up12VCharging current at input (input terminal current) R/W
Ichg=ISET*0.025A
CHG_STAT
Register address =0xC7
Bit(s) Name Description R/W
7 Reserved
6 Chg_end full of flags R
0: Still charging
1: Already full
5:0 Reserved
Here are just a few precautions that may affect functionality and performance. If there are other precautions, additional documents will be attached.
VSYScapacitor location
The chip operates with relatively large power and current.VSYSThe location of capacitors on the network will affectDCDCJob stability.VSYSThe capacitors on the
network need to be as close as possible toICofVSYSpins andEPAD, and lay a large area of copper and add more vias to reduce the capacitance and ICThe area of current
VSYSThe pins are distributed on both sides of the chip,Capacitors need to be placed close to the pins on both sides.and inPCBThe upper pass is wider (not less than100mil)
The copper paving will be on both sidesVSYSThe pins are connected together.
VSYSPins need to be placed nearby22uFcapacitor, the capacitor is located close toIP2315pins (section6,7PINand the first18,19PINPlace each1
indivual), it is recommended that the capacitor be placed directly on the back of the chip, as shown below:
D5
SS34 L1
C2 C3 C4 2.2uH
22uF22uF NC/22uF
C5
NC/220uF C6 C8
104 10uF
11
12
13
14
15
18
19
6
7
VSYS LX BST
BAT
twenty two
C9
104
20 Charger driver
R3
VIN twenty one
8 100R
CC1 VIN LED1
C1 R4
CC2 10uF 10K VBAT
LED2 9
TYPE-C DM
DP
GND
2 CC1 IP2315 LED3 10
3 CC2
DM
twenty three
DP
twenty four
1
4 D1
5
25
28 D2
29
30
EPAD
RVSET
27
26
16
R2
R1
RICHG RNTC 100R
82K DH
RICHG sets the charging current RVSET sets the constant voltage charging voltage
serial number Component name Model & Specifications Location Dosage Remark