Professional Documents
Culture Documents
AOZ2023PI
AOZ2023PI
Typical Application
VIN VOUT
VIN VOUT
C3
R1 C5 C6
10µF C1
22µF 10µF/NI
AOZ2023 FB
R2
EN
C4
1µF
POK
CNTL
C2
GND GND
1µF
R3
Ordering Information
Part Number Ambient Temperature Range Package Environmental
AOZ2023PI -40 °C to +85 °C EPAD SO-8 Green Product
AOS Green Products use reduced levels of Halogens, and are also RoHS compliant.
Please visit www.aosmd.com/media/AOSGreenPolicy.pdf for additional information.
Pin Configuration
POK 1 8 GND
EN 2 Exposed 7 FB
PAD
VCNTL 4 5 NC
EPAD SO-8
(Top View)
Pin Description
Pin Number Pin Name Pin Function
1 POK Power OK Indication. This pin is an open-drain output and is set high impedance once
VOUT reaches 90% of its rating voltage.
2 EN Enable Input. Pulling this pin below 0.8V turns the regulator off, reducing the quiescent
current to a fraction of its operating value.
3 VIN Input Voltage. This is the drain input to the power device that supply current to the output
pin. Large bulk capacitors with low ESR should be placed physically close to this pin o
prevent the input rail from dropping during large load transient. A 10μF ceramic capacitor is
recommended at this pin.
4 VCNTL Supply Input for Control Circuit. This pin provides bias voltage to the control circuitry and
driver for the pass transistor. The driving capability of output current is proportioned to the
VCNTL. For the device to regulate, the voltage on this pin must be at least 1.5V greater
than the output voltage, and no less than VCNTL_min.
5 NC Not Internally Connected.
6 VOUT Output Voltage. This pin is power output of the device. A pull low resistance exists when the
device is disabled by pulling low the EN pin.
7 FB Feedback Voltage. This pin is the inverting input to the error amplifier. A resistor divider
from the output to GND is used to set the regulation voltage as VOUT=0.8x(R1+R2)/R2 (V).
8 GND Ground.
Exposed PAD GND Ground. The exposed pad acts the dominant power dissipation path and should be
soldered to well design PCB pads.
Block Diagram
EN VCNTL VIN
OTP POR
Softstart &
Control Logic OCP
FB
0.8V Vref
VOUT
0.2V
POK
Delay
90% Vref
GND
Electrical Characteristics
TA = 25 °C, VIN = 1.4V, VCNTL = VEN = 5V, CIN = COUT = 10μF, unless otherwise specified. Specifications in BOLD indicate a
temperature of -40°C to +85°C.
Functional Characteristics
Circuit of Typical Application 1. TA = 25°C, VIN = 1.5V, VCNTL = 5V, VOUT = 1.05V, unless otherwise specified.
VO(AC) VO(AC)
(10mV/div) (10mV/div)
IO IO
(1A/div) (1A/div)
2ms/div 2ms/div
VIN Line Transient Response (0A) VIN Line Transient Response (2A)
VIN VIN
(1V/div) (1V/div)
VO(AC) VO(AC)
(10mV/div) (10V/div)
IO
(1A/div)
IO
(1A/div)
5ms/div 5ms/div
VEN VIN
(2V/div) (1V/div)
VO VO
(1V/div) (1V/div)
VPOK VPOK
(2V/div) (2V/div)
IO IO
(2A/div) (2A/div)
500µs/div 500µs/div
VCNTL
(2V/div)
VO
(1V/div) VO
(1V/div)
VPOK
(2V/div)
IO IO
(2A/div) (2A/div)
500µs/div 500µs/div
VIN
(5V/div)
VO
VO (1V/div)
(1V/div)
IO IO
(2A/div) (2A/div)
20ms/div 500µs/div
50 3.2
3.1
0 3.0
0 0.4 0.8 1.2 1.6 2.0 -40 -20 0 20 40 60 80
Load (A) Temperature (°C)
0.09 1.40
0.08 1.35
0.07 1.30
0.06 1.25
0.05 1.20
0.04 1.15
0.03 1.10
0.02 1.05
0.01 1.00
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Temperature (°C) Temperature (°C)
VCNTL POR Threshold Voltage vs. Temperature Reference Voltage vs. Temperature
3.00 0.820
2.95 0.815
VCNTL POR Voltage (V)
2.90
0.810
2.85
0.805
2.80
2.75 0.800
2.70 0.795
2.65 0.790
2.60
0.785
2.55
0.780
2.50
2.45 0.775
2.40 0.770
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Temperature (°C) Temperature (°C)
L1
E2 E3 E1 E
D1 L1'
Note 5
D
θ
7 (4x)
A2 A
B e
A1
Carrier Tape P1
D1
P2
T
E1
E2 E
B0
K0 D0
A0 P0 Feeding Direction
UNIT: mm
Package A0 B0 K0 D0 D1 E E1 E2 P0 P1 P2 T
SO-8 6.40 5.20 2.10 1.60 1.50 12.00 1.75 5.50 8.00 4.00 2.00 0.25
(12mm) ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.10 ±0.10
Reel
W1
S
G
N K
M
V
R
H
W
UNIT: mm
Tape Size Reel Size M N W W1 H K S G R V
12mm ø330 ø330.00 ø97.00 13.00 17.40 ø13.00 10.60 2.00 — — —
±0.50 ±0.10 ±0.30 ±1.00 +0.50/-0.20 ±0.50
Part Marking
AOZ2023PI
(SO-8)
Z2023PI
Part Number Code
FAYWLT
LEGAL DISCLAIMER
Alpha and Omega Semiconductor makes no representations or warranties with respect to the accuracy or
completeness of the information provided herein and takes no liabilities for the consequences of use of such
information or any product described herein. Alpha and Omega Semiconductor reserves the right to make changes
to such information at any time without further notice. This document does not constitute the grant of any intellectual
property rights or representation of non-infringement of any third party’s intellectual property rights.
ALPHA AND OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS.
As used herein:
1. Life support devices or systems are devices or 2. A critical component in any component of a life
systems which, (a) are intended for surgical implant into support, device, or system whose failure to perform can
the body or (b) support or sustain life, and (c) whose be reasonably expected to cause the failure of the life
failure to perform when properly used in accordance support device or system, or to affect its safety or
with instructions for use provided in the labeling, can be effectiveness.
reasonably expected to result in a significant injury of
the user.