Professional Documents
Culture Documents
VSL Storage Shed (512) Str. Calculation Sheet
VSL Storage Shed (512) Str. Calculation Sheet
SHEET
PROJECT 10th RAMADAN COMPLEX JOB NO. 10171A CALC NO. 09-DBC-0512-00001 1 of 170
RECORD OF REVISIONS
PGESCO Confidential
© PGESCO 2023. Contains confidential and/or proprietary to PGESCO and its affiliated companies which shall
not to be used, disclosed, or reproduced in any format by any non-PGESCO party without PGESCO's prior
written permission. All rights reserved.
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 07/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
Table of contents
PGESCo Confidential
© Copyright 2023. All rights reserved
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 07/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
1- Purpose:
The purpose of this calculation is to perform complete analysis and design for
VSL Storage Shed (Steel Structure)
2- References:
1- ECP-205 2001 Egyptian Code of practice for steel construction and bridges
(Allowable Stress design – ASD).
2- ECP – 201 2012 Egyptian Code of Practice for Loadings.
3- EN 10025 Hot rolled products of structural steels. Technical delivery conditions
4- ANSI/AISC 360-14 Specification for Structural Steel Buildings, published by the American
Institute of Steel Construction.
5- AWS D1.1 2015 Structural welding Code- Steel.
6- RCSC 2014 Specification for Structural Joints Using High-Strength Bolts, published by
Research Council on Structural Connections
7- Design_Guide_7__Industrial_Buildings--Roofs_to_Anchor_Rods_(Third_Edition).
8- Metal Building Manufacturers Association (MBMA-2006).
HZ Bracing at top level are used to transmit lateral loads to portal frame bracing
then to the foundations.
PGESCo Confidential
© Copyright 2023. All rights reserved
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 07/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
Coordination system:
+Z, denotes North - South direction. Y
-Z, denotes South - North direction.
X
+X, denotes West - East direction.
-X, denotes East - West direction.
+Y, denotes Upward direction.
-Y, denotes Downward direction. Z
PGESCo Confidential
© Copyright 2023. All rights reserved
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 07/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
5- Analysis and Design methodologies:
PGESCo Confidential
© Copyright 2023. All rights reserved
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 07/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
6- Loads and load combinations:-
6.1- Independent loads (Primary loads):
app.(3)&att. (C)
PGESCo Confidential
© Copyright 2023. All rights reserved
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 07/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
For the lateral Stability System ( Bracing System) in the Z Direction the following load combination are used
as The wind Load considered as the Primary Load
1. D 7. 0.833(D + RL + LL ± T)
2. D + RL + LL 8. D+ L+W
3. (D + RL + LL +W) 9. 0.833D + 0.250 L + 0.595 EQ
4. (0.9D +W) 10. 0.9 D + W
5. 0.833(D + Q) 11. 0.75 D ± 0.595 EQ
6. 0.833(D ± T)
7- Check on lateral and Vertical deflection:-
The maximum sway of building due to non-seismic forces in any story of the height (H) shall be ref. (1)
H/150 for steel moment-resisting building frames (N-S), X-direction.
The maximum Defliction of building due to non-seismic forces in any Beam of the Span (S) shall be ref. (1)
S/200 for steel moment-resisting building frames , Y-direction.
So,
At Top level:- Height of steel = 7000 mm
Drift in X-direction
Maximum actual drift = 45.00 mm at TYP Frame Eave
The allowable drift = (Height of steel) / 150 = 46.67 mm O.K.
PGESCo Confidential
© Copyright 2023. All rights reserved
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 07/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
PGESCo Confidential
© Copyright 2023. All rights reserved
Calculation Sheet
Subject Discipline
VSL Storage Shed (512) Calculation Sheet Civil/ Structural
By: Date: Checked By: Date: Sheet Rev. Sheet No.
N.M 06/10/2023 MMH 06/10/2023 0
Combined Moments and Axial Loads Design
According to ECP (205)-ASD
Define steel modulus of elasticity, and shear modulus: E = 2100 t/cm2 G = 810 t/cm2
Define steel yield strength (Fy ): 3.60 t/cm2 Define Type of Member used: Welded
Define steel ultimate strength (Fu ): 5.20 t/cm2 Design State ASD
Section Properties
A s (cm 2 ) dw (cm) b f (cm) t w (cm) t f (cm) h / tw b f / 2t f I x (cm 4 ) I y (cm 4 )
90.0 50.00 25.00 0.60 1.20 82.33 10.42 45578.80 3125.90
S x (cm 3 ) S y (cm 3 ) r x (cm) r y (cm) C(cm) S WELD(cm) h(cm)
1739.65 250.07 22.50 5.89 11.90 0.30 49.40
Define Ky value for buckling about the weak axis: Ky = 1.00 Define Compression Slenderness limit (KL/r ) : 180
Define Kx value for buckling about the strong axis: Kx = 2.00 Define Tension Slenderness limit (KL/r ) : 300
Define unbraced length for buckling about the weak axis: Ly = 7.00 m
Define unbraced length for buckling about the strong axis: Lx = 7.00 m
Define laterally unsupported length of the compression flange: L ub = 7.00 m
Top Flange Only No
Acting Loads
Define max. axial load: P = 7.17 ton 70.3 Kn Compression
Define strong axis moment: Mx = 18.18 ton 178.3 Kn.m Cb = 1.00
Define weak axis moment: My = 0.00 ton 0.0 Kn.m Cmx = 0.85
Define Shear Force: Vy = 2.69 ton 26.3 Kn Cmy = 0.85
Flanges:
C/tf = 9.92 Non-Compact
Web:
dw/tw = 82.33 Non-Compact
Stresses - Summary :
Fca 0.532 t/cm2 Fbcx 1.291 t/cm2 Fbcy 2.088 t/cm2 Qc 0.945 t/cm2
fca 0.080 t/cm2 fbcx 1.045 t/cm2 fbcy 0.000 t/cm2 Q 0.090 t/cm2
Buckling is Safe
Member is Safe
Solution:
2-Moment capacity :
There is LTB
3-Shear capacity :
Qc = 0.945 t/cm2
Define steel modulus of elasticity, and shear modulus: E = 2100 t/cm2 G = 810 t/cm2
Define steel yield strength (Fy ): 3.60 t/cm2 Define Type of Member used: Welded
Define steel ultimate strength (Fu ): 5.20 t/cm2 Design State ASD
Section Properties
A s (cm 2 ) dw (cm) b f (cm) t w (cm) t f (cm) h / tw b f / 2t f I x (cm 4 ) I y (cm 4 )
135.0 50.00 25.00 0.60 1.20 87.33 10.42 47141.80 19537.40
S x (cm 3 ) S y (cm 3 ) r x (cm) r y (cm) C(cm) S WELD(cm) h(cm) X(cm) Y(cm)
1799.31 991.75 18.69 12.03 12.20 #N/A 52.40 19.70 26.20
Define Ky value for buckling about the weak axis: Ky = 2.00 Define Compression Slenderness limit (KL/r ) : 180
Define Kx value for buckling about the strong axis: Kx = 2.00 Define Tension Slenderness limit (KL/r ) : 300
Define unbraced length for buckling about the weak axis: Ly = 7.00 m
Define unbraced length for buckling about the strong axis: Lx = 7.00 m
Define laterally unsupported length of the compression flange: L ub = 6.00 m
Top Flange Only No
Acting Loads
Define max. axial load: P = 8.41 ton 82.6 Kn Compression
Define strong axis moment: Mx = 17.04 ton 167.2 Kn.m Cb = 1.00
Define weak axis moment: My = 4.03 ton 39.5 Kn.m Cmx = 0.85
Define Shear Force: Vy = 0.74 ton 7.3 Kn Cmy = 0.85
Flanges:
C/tf = 10.17 Non-Compact
Web:
dw/tw = 87.33 Non-Compact
Stresses - Summary :
Fca 0.554 t/cm2 Fbcx 1.626 t/cm2 Fbcy 2.088 t/cm2 Qc 0.945 t/cm2
fca 0.062 t/cm2 fbcx 0.947 t/cm2 fbcy 0.406 t/cm2 Q 0.025 t/cm2
Buckling is Safe
Member is Safe
Solution:
2-Moment capacity :
There is LTB
3-Shear capacity :
Qc = 0.945 t/cm2
Define steel modulus of elasticity, and shear modulus: E = 2100 t/cm2 G = 810 t/cm2
Define steel yield strength (Fy ): 3.60 t/cm2 Define Type of Member used: Welded
Define steel ultimate strength (Fu ): 5.20 t/cm2 Design State ASD
Section Properties
A s (cm 2 ) dw (cm) b f (cm) t w (cm) t f (cm) h / tw b f / 2t f I x (cm 4 ) I y (cm 4 )
70.0 50.00 20.00 0.60 1.00 82.33 10.00 32263.33 1334.23
S x (cm 3 ) S y (cm 3 ) r x (cm) r y (cm) C(cm) S WELD(cm) h(cm)
1240.90 133.42 21.47 4.37 9.40 0.30 49.40
Define Ky value for buckling about the weak axis: Ky = 1.00 Define Compression Slenderness limit (KL/r ) : 180
Define Kx value for buckling about the strong axis: Kx = 1.00 Define Tension Slenderness limit (KL/r ) : 300
Define unbraced length for buckling about the weak axis: Ly = 7.50 m
Define unbraced length for buckling about the strong axis: Lx = 15.00 m
Define laterally unsupported length of the compression flange: L ub = 3.00 m
Top Flange Only No
Acting Loads
Define max. axial load: P = 3.02 ton 29.6 Kn Compression
Define strong axis moment: Mx = 19.31 ton 189.5 Kn.m Cb = 1.00
Define weak axis moment: My = 0.00 ton 0.0 Kn.m Cmx = 0.85
Define Shear Force: Vy = 6.93 ton 68.0 Kn Cmy = 0.85
Flanges:
C/tf = 9.40 Non-Compact
Web:
dw/tw = 82.33 Non-Compact
Stresses - Summary :
Fca 0.254 t/cm2 Fbcx 2.088 t/cm2 Fbcy 2.088 t/cm2 Qc 0.945 t/cm2
fca 0.043 t/cm2 fbcx 1.557 t/cm2 fbcy 0.001 t/cm2 Q 0.231 t/cm2
Buckling is Safe
Member is Safe
Solution:
2-Moment capacity :
There is LTB
3-Shear capacity :
Qc = 0.945 t/cm2
Define steel modulus of elasticity, and shear modulus: E = 2100 t/cm2 G = 810 t/cm2
Define steel yield strength (Fy ): 2.4 t/cm2 Define Type of Member used: Rolled
Define steel ultimate strength (Fu ): 3.6 t/cm2 Design State ASD
Section Properties
A s (cm 2 ) h (cm) b (cm) t (cm) I x (cm 4 ) I y (cm 4 )
19.36 12.5 12.5 0.4 472.93 472.93
S x (cm 3 ) S y (cm 3 ) r x (cm) r y (cm)
75.67 75.67 4.94 4.94
Define Ky value for buckling about the weak axis: Ky = 1.00 Define Compression Slenderness limit (KL/r ) : 180
Define Kx value for buckling about the strong axis: Kx = 1.00 Define Tension Slenderness limit (KL/r ) : 300
Define unbraced length for buckling about the weak axis: Ly = 7.50 m
Define unbraced length for buckling about the strong axis: Lx = 7.50 m
Define laterally unsupported length of the compression flange: L ub = 7.50 m
Acting Loads
Define max. axial load: P = 0.00 ton 0.00 Compression
Define strong axis moment: Mx = 0.29 t.m Cb = 1.00
Define weak axis moment: My = 0.00 t.m Cmx = 0.85
Define Shear Force: Vy = 0.00 ton Cmy = 0.85
Flanges:
C/tf = 29.25 Compact
Web:
dw/tw = 29.25 Compact
Stresses - Summary :
Fca 0.326 t/cm2 Fbcx 1.536 t/cm2 Fbcy 1.536 t/cm2 Qc 0.840 t/cm2
fca 0.000 t/cm2 fbcx 0.377 t/cm2 fbcy 0.000 t/cm2 Q 0.000 t/cm2
Member is Safe
2-Moment capacity :
3-Shear capacity :
Qc = 0.840 t/cm2
Define steel modulus of elasticity, and shear modulus: E = 2100 t/cm2 G = 810 t/cm2
Define steel yield strength (Fy ): 3.60 t/cm2 Define Type of Member used: Welded
Define steel ultimate strength (Fu ): 5.20 t/cm2 Design State ASD
Section Properties
A s (cm 2 ) dw (cm) b f (cm) t w (cm) t f (cm) h / tw b f / 2t f I x (cm 4 ) I y (cm 4 )
58.0 30.00 20.00 0.60 1.00 49.00 10.00 10963.33 1333.87
S x (cm 3 ) S y (cm 3 ) r x (cm) r y (cm) C(cm) S WELD(cm) h(cm)
685.21 133.39 13.75 4.80 9.40 0.30 29.40
Define Ky value for buckling about the weak axis: Ky = 1.00 Define Compression Slenderness limit (KL/r ) : 180
Define Kx value for buckling about the strong axis: Kx = 1.00 Define Tension Slenderness limit (KL/r ) : 300
Define unbraced length for buckling about the weak axis: Ly = 7.50 m
Define unbraced length for buckling about the strong axis: Lx = 15.00 m
Define laterally unsupported length of the compression flange: L ub = 3.00 m
Top Flange Only No
Acting Loads
Define max. axial load: P = 2.34 ton 22.9 Kn Compression
Define strong axis moment: Mx = 7.70 ton 75.6 Kn.m Cb = 1.00
Define weak axis moment: My = 0.00 ton 0.0 Kn.m Cmx = 0.85
Define Shear Force: Vy = 0.89 ton 8.8 Kn Cmy = 0.85
Flanges:
C/tf = 9.40 Non-Compact
Web:
dw/tw = 49.00 Compact
Stresses - Summary :
Fca 0.307 t/cm2 Fbcx 2.088 t/cm2 Fbcy 2.088 t/cm2 Qc 1.260 t/cm2
fca 0.040 t/cm2 fbcx 1.124 t/cm2 fbcy 0.000 t/cm2 Q 0.050 t/cm2
Buckling is Safe
Member is Safe
Solution:
2-Moment capacity :
There is LTB
3-Shear capacity :
Qc = 1.260 t/cm2
Define steel modulus of elasticity, and shear modulus: E = 2100 t/cm2 G = 810 t/cm2
Define steel yield strength (Fy ): 2.4 t/cm2 Define Type of Member used: Rolled
Define steel ultimate strength (Fu ): 3.6 t/cm2 Design State ASD
Section Properties
A s (cm 2 ) h (cm) b (cm) t (cm) I x (cm 4 ) I y (cm 4 )
19.36 12.5 12.5 0.4 472.93 472.93
S x (cm 3 ) S y (cm 3 ) r x (cm) r y (cm)
75.67 75.67 4.94 4.94
Define Ky value for buckling about the weak axis: Ky = 0.75 Define Compression Slenderness limit (KL/r ) : 200
Define Kx value for buckling about the strong axis: Kx = 0.50 Define Tension Slenderness limit (KL/r ) : 300
Define unbraced length for buckling about the weak axis: Ly = 10.30 m
Define unbraced length for buckling about the strong axis: Lx = 10.30 m
Define laterally unsupported length of the compression flange: L ub = 10.30 m
Acting Loads
Define max. axial load: P = 0.48 ton 4.75 Compression
Define strong axis moment: Mx = 0.00 t.m Cb = 1.00
Define weak axis moment: My = 0.00 t.m Cmx = 0.85
Define Shear Force: Vy = 0.00 ton Cmy = 0.85
Flanges:
C/tf = 29.25 Compact
Web:
dw/tw = 29.25 Compact
Stresses - Summary :
Fca 0.307 t/cm2 Fbcx 1.536 t/cm2 Fbcy 1.536 t/cm2 Qc 0.840 t/cm2
fca 0.025 t/cm2 fbcx 0.000 t/cm2 fbcy 0.000 t/cm2 Q 0.000 t/cm2
Member is Safe
2-Moment capacity :
3-Shear capacity :
Qc = 0.840 t/cm2
PGESCo Confidential
© Copyright 2023. All rights reserved
PGESCO
Current Date: 10/4/2023 6:51 PM
Units system: SI
File name: E:\Nora\10th of ramadan complex\Ram Connection\T.DET-01.rcnx
Steel connections
Results
___________________________________________________________________________________________________________________________
___________________________________________________________________________________________________________________________
DEMANDS
Description Pu Mu22 Mu33 Vu2 Vu3 Load type
[kN] [kN*m] [kN*m] [kN] [kN]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
L1 23.00 0.00 0.00 44.60 11.70 Design
L2 -142.20 0.00 0.00 44.60 11.70 Design
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Base plate
Distance from anchor to edge [mm] 80.48 6.35 --
Weld size [1/16in] 3 2 -- table J2.4
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Concrete base
Axial bearing [KN/mm2] 0.02 0.00 L2 0.08 DG1 3.1.1;
Base plate
Flexural yielding (bearing interface) [KN*m/m] 31.95 1.38 L2 0.04 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 31.95 2.88 L1 0.09 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1097.08 55.29 L1 0.05 p. 8-9,
Sec. J2.5,
Sec. J2.4,
DG1 p. 35
Elastic method weld shear capacity [KN/m] 731.39 74.33 L1 0.10 p. 8-9,
Sec. J2.5,
Sec. J2.4
Elastic method weld axial capacity [KN/m] 1097.08 23.28 L1 0.02 p. 8-9,
Sec. J2.5,
Sec. J2.4
Ratio 0.10
Page1
Design for minor axis
Base plate (AISC 360-16 LRFD)
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Base plate
Distance from anchor to edge [mm] 80.48 6.35 --
Weld size [1/16in] 3 2 -- table J2.4
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Concrete base
Axial bearing [KN/mm2] 0.02 0.00 L2 0.08 DG1 3.1.1;
Base plate
Flexural yielding (bearing interface) [KN*m/m] 31.95 1.38 L2 0.04 DG1 Sec 3.1.2
Flexural yielding (tension interface) [KN*m/m] 31.95 2.88 L1 0.09 DG1 Eq. 3.3.13
Column
Weld capacity [KN/m] 1097.08 55.29 L1 0.05 p. 8-9,
Sec. J2.5,
Sec. J2.4,
DG1 p. 35
Elastic method weld shear capacity [KN/m] 731.39 11.84 L1 0.02 p. 8-9,
Sec. J2.5,
Sec. J2.4
Elastic method weld axial capacity [KN/m] 1097.08 23.28 L1 0.02 p. 8-9,
Sec. J2.5,
Sec. J2.4
Ratio 0.09
Major axis
Anchors
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Anchors
Anchor spacing [mm] 110.00 76.20 -- Sec. D.8.1
Concrete cover [mm] 135.48 76.20 -- Sec. 7.7.1
Effective length [mm] 612.38 -- 1037.62
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Page2
Interaction of tensile and shear forces [KN] 1.20 0.70 L1 0.58 Eq. D-2,
Eq. D-3,
Sec. D.3.3.4.4,
Eq. D-4,
Sec. D.5.4.1,
Eq. D-17,
Eq. D-29,
Sec. D.6.1.3,
Table D.4.1.1,
Sec. D.4.3,
Eq. D-42
Ratio 0.66
Minor axis
Anchors
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Anchors
Anchor spacing [mm] 110.00 76.20 -- Sec. D.8.1
Concrete cover [mm] 135.48 76.20 -- Sec. 7.7.1
Effective length [mm] 612.38 -- 1037.62
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Ratio 0.36
Page3
Global critical strength ratio 0.66
Major axis
Maximum compression (L2)
------------------------------------------------------------------------------------------------------------------------------------------------------------
Maximum bearing pressure 1.36 [N/mm2]
Minimum bearing pressure 1.36 [N/mm2]
Maximum anchor tension 0.00 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 1E33 [mm]
Bearing length 360.00 [mm]
------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[mm] [mm] [kN] [kN]
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1 -55.00 -60.00 11.15 0.00
2 -55.00 60.00 11.15 0.00
3 55.00 60.00 11.15 0.00
4 55.00 -60.00 11.15 0.00
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------------------------------------------------------------------
Maximum bearing pressure 0.00 [N/mm2]
Minimum bearing pressure 0.00 [N/mm2]
Maximum anchor tension 5.75 [kN]
Minimum anchor tension 5.75 [kN]
Neutral axis angle 0.00 [deg]
Page4
Neutral axis location -1E33 [mm]
Bearing length 0.00 [mm]
----------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[mm] [mm] [kN] [kN]
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1 -55.00 -60.00 11.15 5.75
2 -55.00 60.00 11.15 5.75
3 55.00 60.00 11.15 5.75
4 55.00 -60.00 11.15 5.75
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Minor axis
Maximum compression (L2)
------------------------------------------------------------------------------------------------------------------------------------------------------------
Maximum bearing pressure 1.36 [N/mm2]
Minimum bearing pressure 1.36 [N/mm2]
Maximum anchor tension 0.00 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location 1E33 [mm]
Bearing length 290.00 [mm]
------------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[mm] [mm] [kN] [kN]
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1 -55.00 -60.00 2.93 0.00
2 -55.00 60.00 2.93 0.00
3 55.00 60.00 2.93 0.00
4 55.00 -60.00 2.93 0.00
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Page5
Maximum tension (L1)
----------------------------------------------------------------------------------------------------------------------------------------------------------
Maximum bearing pressure 0.00 [N/mm2]
Minimum bearing pressure 0.00 [N/mm2]
Maximum anchor tension 5.75 [kN]
Minimum anchor tension 5.75 [kN]
Neutral axis angle 0.00 [deg]
Neutral axis location -1E33 [mm]
Bearing length 0.00 [mm]
----------------------------------------------------------------------------------------------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[mm] [mm] [kN] [kN]
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1 -55.00 -60.00 2.93 5.75
2 -55.00 60.00 2.93 5.75
3 55.00 60.00 2.93 5.75
4 55.00 -60.00 2.93 5.75
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Results for tensile breakout (L1)
Page6
Minor axis
Results for tensile breakout (L1)
Page7
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.01
Analysis Stress, strain/ simplified loading
Design code AISC - LRFD 2016
1/8
Project:
Project no:
Author:
2/8
Project:
Project no:
Author:
Cross-sections
Name Material
6 - Iwn324x(250/250) ST52
Cross-sections
Name Material Drawing
6 - Iwn324x(250/250) ST52
Anchors
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M20 ST52 M20 ST52 20 520.0 314
3/8
Project:
Project no:
Author:
Foundation block
Item Value Unit
CB 1
Dimensions 390 x 464 mm
Depth 800 mm
Anchor M20 ST52
Anchoring length 600 mm
Shear force transfer Anchors
Mortar joint 30 mm
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.0 < 5.0% OK
Anchors 29.1 < 100% OK
Welds 15.3 < 100% OK
Concrete block 7.3 < 100% OK
Buckling Not calculated
Plates
fy Thickness σEd εPl σcEd
Name Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Column -tfl 1 360.0 12.0 LE1 36.7 0.0 0.0 OK
Column -bfl 1 360.0 12.0 LE2 51.9 0.0 0.0 OK
Column -w 1 360.0 6.0 LE2 58.3 0.0 0.0 OK
BP1 360.0 20.0 LE1 32.3 0.0 0.0 OK
Design data
fy εlim
Material
[MPa] [%]
ST52 360.0 5.0
4/8
Project:
Project no:
Author:
5/8
Project:
Project no:
Author:
Anchors
Nf V Utt Uts Utts
Shape Item Loads Status
[kN] [kN] [%] [%] [%]
A1 LE1 5.9 11.5 6.6 29.1 13.8 OK
Design data
ϕNsa ϕVsa
Grade
[kN] [kN]
M20 ST52 - 1 89.2 39.7
6/8
Project:
Project no:
Author:
Where:
ϕ = 0.70 – resistance factor
Where:
rm = 0.8 – reduction factor for steel strength in shear in case of mortar joint
ϕ = 0.65 – resistance factor
Ase,V = 245 mm2 – tensile stress area
futa = 520.0 MPa – specified tensile strength of anchor steel:
Where:
Utt = 0.07 – maximum ratio of factored tensile force and tensile resistance determined from all appropriate failure
modes
Uts = 0.29 – maximum ratio of factored shear force and shear resistance determined from all appropriate failure
modes
Weld sections
Th Ls L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
BP1 Column -tfl 1 E70xx ◢5.7◣ ◢8.0◣ 249 23 LE2 4.0 38.7 10.3 OK
E70xx ◢5.7◣ ◢8.0◣ 249 23 LE2 4.8 37.2 12.9 OK
BP1 Column -bfl 1 E70xx ◢5.7◣ ◢8.0◣ 249 23 LE2 5.7 37.4 15.3 OK
E70xx ◢5.7◣ ◢8.0◣ 249 23 LE2 3.8 39.1 9.6 OK
BP1 Column -w 1 E70xx ◢3.5◣ ◢5.0◣ 299 23 LE2 3.2 24.0 13.4 OK
E70xx ◢3.5◣ ◢5.0◣ 299 23 LE2 3.2 24.1 13.2 OK
7/8
Project:
Project no:
Author:
Where:
Fnw = 388.9 MPa – nominal stress of weld material:
Concrete block
A1 A2 σ Ut
Item Loads Status
[mm2] [mm2] [MPa] [%]
CB 1 LE2 93712 174439 1.5 7.3 OK
Where:
fp,max = 32.0 MPa – concrete block design bearing strength:
Buckling
Buckling analysis was not calculated.
8/8
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 04/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
PGESCo Confidential
© Copyright 2023. All rights reserved
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.02
Analysis Stress, strain/ simplified loading
Design code AISC - ASD 2016
1 / 12
Project:
Project no:
Author:
2 / 12
Project:
Project no:
Author:
Cross-sections
Name Material
6 - Iwn532x(250/250) ST52
7 - Iwn520x(200/200) A36
5 - RHS125x125 ST37
3 / 12
Project:
Project no:
Author:
Cross-sections
Name Material Drawing
6 - Iwn532x(250/250) ST52
7 - Iwn520x(200/200) A36
5 - RHS125x125 ST37
Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M16 Grade8.8 M16 Grade8.8 16 800.0 201
M22 Grade8.8 M22 Grade8.8 22 800.0 380
4 / 12
Project:
Project no:
Author:
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.1 < 5.0% OK
Bolts 75.9 < 100% OK
Welds 78.3 < 100% OK
Buckling Not calculated
5 / 12
Project:
Project no:
Author:
Plates
fy Thickness σEd εPl σcEd
Name Material Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Column -tfl 1 ST52 360.0 20.0 LE1 178.7 0.0 20.7 OK
Column -bfl 1 ST52 360.0 12.0 LE3 135.2 0.0 0.0 OK
Column -w 1 ST52 360.0 10.0 LE1 160.3 0.0 0.0 OK
Rafter-tfl 1 A36 248.2 10.0 LE1 147.7 0.0 0.0 OK
Rafter-bfl 1 A36 248.2 10.0 LE4 148.6 0.0 0.0 OK
Rafter-w 1 A36 248.2 6.0 LE4 141.5 0.0 0.0 OK
Strut-1 ST37 240.0 4.0 LE2 124.8 0.0 0.0 OK
Strut-2 ST37 240.0 4.0 LE4 127.9 0.0 0.0 OK
SP5 ST52 360.0 10.0 LE1 93.4 0.0 10.1 OK
CPL1 ST52 360.0 10.0 LE1 101.0 0.0 10.1 OK
SP6 ST52 360.0 10.0 LE3 93.0 0.0 10.2 OK
CPL2 ST52 360.0 10.0 LE3 101.7 0.0 10.2 OK
EP1 ST52 360.0 20.0 LE3 152.8 0.0 29.4 OK
SP3 ST52 360.0 10.0 LE1 113.6 0.0 0.0 OK
SP4 ST52 360.0 10.0 LE4 81.0 0.0 0.0 OK
SP7 ST52 360.0 10.0 LE4 77.7 0.0 0.0 OK
RIB1 ST52 360.0 10.0 LE4 204.7 0.1 0.0 OK
RIB2 ST52 360.0 10.0 LE1 183.0 0.0 0.0 OK
SP8 ST52 360.0 10.0 LE1 152.7 0.0 0.0 OK
Design data
fy εlim
Material
[MPa] [%]
ST52 360.0 5.0
A36 248.2 5.0
ST37 240.0 5.0
6 / 12
Project:
Project no:
Author:
7 / 12
Project:
Project no:
Author:
8 / 12
Project:
Project no:
Author:
Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 M16 Grade8.8 - 1 LE2 3.0 2.0 66.1 4.9 5.6 - OK
Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
M16 Grade8.8 - 1 60.3 36.2
M22 Grade8.8 - 2 114.0 68.4
Where:
Fnt = 600.0 MPa – nominal tensile stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
9 / 12
Project:
Project no:
Author:
Where:
Fnv = 360.0 MPa – nominal shear stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 274.6 kN ≥ V = 1.7 kN
Where:
lc = 129 mm – clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 20 mm – thickness of the plate
d = 22 mm – diameter of a bolt
Fu = 520.0 MPa – tensile strength of the connected material
Ω = 2.00 – safety factor for bearing at bolt holes
10 / 12
Project:
Project no:
Author:
Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
CPL1 Strut-2-w 1 E70xx ◢3.5 ◢5.0 149 10 LE2 2.8 7.2 39.1 OK
CPL1 Strut-2-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.6 7.5 35.0 OK
CPL1 Strut-2-w 3 E70xx ◢3.5 ◢5.0 149 10 LE4 2.8 7.5 37.5 OK
CPL1 Strut-2-w 3 E70xx ◢3.5 ◢5.0 149 10 LE3 2.9 7.2 40.5 OK
Column -w 1 SP5 E70xx ◢3.5◣ ◢5.0◣ 259 16 LE1 4.1 11.4 36.1 OK
E70xx ◢3.5◣ ◢5.0◣ 259 16 LE3 4.1 10.9 37.3 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE2 2.7 7.2 37.8 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE2 2.7 7.5 35.3 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE3 2.6 7.5 34.6 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE3 2.8 7.2 39.6 OK
Column -w 1 SP6 E70xx ◢3.5◣ ◢5.0◣ 259 16 LE1 4.6 11.3 41.2 OK
E70xx ◢3.5◣ ◢5.0◣ 259 16 LE3 3.3 11.3 28.8 OK
EP1 Rafter-tfl 1 E70xx ◢5.7◣ ◢8.0◣ 200 50 LE1 43.5 60.9 71.4 OK
E70xx ◢5.7◣ ◢8.0◣ 200 50 LE1 41.3 60.8 67.9 OK
EP1 Rafter-bfl 1 E70xx ◢5.7◣ ◢8.0◣ 200 50 LE4 30.2 60.4 49.9 OK
E70xx ◢5.7◣ ◢8.0◣ 200 50 LE4 30.0 60.0 49.9 OK
EP1 Rafter-w 1 E70xx ◢3.5◣ ◢5.0◣ 501 46 LE3 19.9 35.0 57.0 OK
E70xx ◢3.5◣ ◢5.0◣ 501 46 LE3 20.0 34.9 57.2 OK
SP3 Column -w 1 E70xx ◢3.5◣ ◢5.0◣ 501 33 LE1 17.6 23.8 73.8 OK
E70xx ◢3.5◣ ◢5.0◣ 501 33 LE1 17.9 23.8 75.0 OK
SP3 Column -bfl 1 E70xx ◢3.5 ◢5.0 249 31 LE3 3.8 23.3 16.5 OK
Column -tfl 1 SP3 E70xx ◢3.5◣ ◢5.0◣ 249 31 LE1 17.9 23.9 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 249 31 LE3 17.9 23.8 75.1 OK
EP1 RIB1 E70xx ◢5.7◣ ◢8.0◣ 99 10 LE4 9.0 12.0 75.2 OK
E70xx ◢5.7◣ ◢8.0◣ 99 10 LE4 9.0 12.0 75.2 OK
Rafter-bfl 1 RIB1 E70xx ◢5.7◣ ◢8.0◣ 149 10 LE4 8.5 11.3 75.1 OK
E70xx ◢5.7◣ ◢8.0◣ 149 10 LE4 8.4 11.3 75.1 OK
EP1 RIB2 E70xx ◢5.7◣ ◢8.0◣ 99 10 LE1 6.8 11.2 60.5 OK
E70xx ◢5.7◣ ◢8.0◣ 99 10 LE1 6.6 11.3 58.7 OK
Rafter-tfl 1 RIB2 E70xx ◢5.7◣ ◢8.0◣ 150 10 LE1 7.9 10.5 75.3 OK
E70xx ◢5.7◣ ◢8.0◣ 150 10 LE1 7.9 10.5 75.3 OK
SP3 SP8 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.5 7.0 78.3 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.5 7.0 78.3 OK
Column -tfl 1 SP8 E70xx ◢3.5◣ ◢5.0◣ 107 10 LE1 5.6 7.4 75.3 OK
E70xx ◢3.5◣ ◢5.0◣ 107 10 LE1 5.6 7.5 75.3 OK
Column -w 1 SP4 E70xx ◢3.5◣ ◢5.0◣ 499 31 LE3 3.5 17.5 19.9 OK
E70xx ◢3.5◣ ◢5.0◣ 499 31 LE1 3.8 23.8 15.9 OK
Column -bfl 1 SP4 E70xx ◢3.5◣ ◢5.0◣ 118 29 LE3 7.1 22.6 31.2 OK
E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 3.6 22.5 16.0 OK
11 / 12
Project:
Project no:
Author:
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
Column -tfl 1 SP4 E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 9.7 22.4 43.5 OK
E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 11.4 22.3 51.2 OK
Column -tfl 1 SP7 E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 11.2 22.6 49.5 OK
E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 11.8 22.6 52.3 OK
Column -bfl 1 SP7 E70xx ◢3.5◣ ◢5.0◣ 118 29 LE3 7.0 22.6 30.8 OK
E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 3.5 22.6 15.7 OK
Column -w 1 SP7 E70xx ◢3.5◣ ◢5.0◣ 499 31 LE3 3.8 17.8 21.5 OK
E70xx ◢3.5◣ ◢5.0◣ 499 31 LE3 3.8 23.8 16.0 OK
Where:
Fnw = 398.6 MPa – nominal stress of weld material:
Buckling
Buckling analysis was not calculated.
12 / 12
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.03
Analysis Stress, strain/ simplified loading
Design code AISC - ASD 2016
1 / 10
Project:
Project no:
Author:
2 / 10
Project:
Project no:
Author:
Cross-sections
Name Material
6 - Iwn320x(200/200) ST52
5 - RHS125x125 ST37
3 / 10
Project:
Project no:
Author:
Cross-sections
Name Material Drawing
6 - Iwn320x(200/200) ST52
5 - RHS125x125 ST37
Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M22 Grade8.8 M22 Grade8.8 22 800.0 380
M16 Grade 8.8 M16 Grade 8.8 16 800.0 201
4 / 10
Project:
Project no:
Author:
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.0 < 5.0% OK
Bolts 68.6 < 100% OK
Welds 77.2 < 100% OK
Buckling Not calculated
Plates
fy Thickness σEd εPl σcEd
Name Material Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Rafter-1-tfl 1 ST52 360.0 10.0 LE3 138.4 0.0 0.0 OK
Rafter-1-bfl 1 ST52 360.0 10.0 LE2 125.8 0.0 0.0 OK
Rafter-1-w 1 ST52 360.0 6.0 LE3 113.2 0.0 0.0 OK
Rafter-2-tfl 1 ST52 360.0 10.0 LE1 162.8 0.0 0.0 OK
Rafter-2-bfl 1 ST52 360.0 10.0 LE4 138.3 0.0 0.0 OK
Rafter-2-w 1 ST52 360.0 6.0 LE1 140.0 0.0 0.0 OK
Strut-1 ST37 240.0 4.0 LE1 128.5 0.0 0.0 OK
Strut-2 ST37 240.0 4.0 LE4 129.3 0.0 0.0 OK
SP1 ST52 360.0 20.0 LE1 129.1 0.0 17.6 OK
SP2 ST52 360.0 20.0 LE1 134.2 0.0 17.9 OK
RIB1 ST52 360.0 10.0 LE2 141.7 0.0 0.0 OK
RIB2 ST52 360.0 10.0 LE1 146.4 0.0 0.0 OK
RIB3 ST52 360.0 10.0 LE1 147.5 0.0 0.0 OK
RIB4 ST52 360.0 10.0 LE4 143.3 0.0 0.0 OK
CPL3 ST52 360.0 10.0 LE2 116.8 0.0 9.1 OK
CPL2 ST52 360.0 10.0 LE3 125.6 0.0 11.7 OK
Design data
fy εlim
Material
[MPa] [%]
ST52 360.0 5.0
ST37 240.0 5.0
5 / 10
Project:
Project no:
Author:
6 / 10
Project:
Project no:
Author:
Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 M22 Grade8.8 - 1 LE3 68.2 3.6 237.6 59.8 5.2 - OK
B2 M22 Grade8.8 - 1 LE3 69.3 3.8 237.5 60.8 5.6 - OK
B3 M22 Grade8.8 - 1 LE1 75.1 3.5 274.6 65.9 5.0 - OK
B4 M22 Grade8.8 - 1 LE1 78.1 3.9 274.6 68.6 5.6 - OK
B5 M22 Grade8.8 - 1 LE1 2.5 3.4 274.6 2.2 5.0 - OK
B6 M22 Grade8.8 - 1 LE1 2.5 3.9 274.6 2.2 5.7 - OK
B7 M22 Grade8.8 - 1 LE1 0.0 2.8 237.5 0.0 4.1 - OK
B8 M22 Grade8.8 - 1 LE1 0.0 3.1 237.6 0.0 4.5 - OK
B9 M16 Grade 8.8 - 2 LE1 0.6 2.6 77.1 0.9 7.2 - OK
B10 M16 Grade 8.8 - 2 LE3 7.9 0.4 99.8 13.1 1.1 - OK
B11 M16 Grade 8.8 - 2 LE4 0.4 3.3 99.8 0.7 9.1 - OK
B12 M16 Grade 8.8 - 2 LE3 0.9 3.2 99.8 1.5 8.8 - OK
B13 M16 Grade 8.8 - 2 LE4 0.8 3.3 99.8 1.4 9.0 - OK
B14 M16 Grade 8.8 - 2 LE3 8.3 2.6 99.8 13.7 7.1 - OK
B15 M16 Grade 8.8 - 2 LE1 0.5 2.7 92.3 0.8 7.3 - OK
B16 M16 Grade 8.8 - 2 LE2 0.7 2.1 99.8 1.2 5.9 - OK
7 / 10
Project:
Project no:
Author:
Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
M22 Grade8.8 - 1 114.0 68.4
M16 Grade 8.8 - 2 60.3 36.2
Where:
Fnt = 600.0 MPa – nominal tensile stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Where:
Fnv = 360.0 MPa – nominal shear stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 274.6 kN ≥ V = 3.9 kN
Where:
lc = 76 mm – clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 20 mm – thickness of the plate
d = 22 mm – diameter of a bolt
Fu = 520.0 MPa – tensile strength of the connected material
Ω = 2.00 – safety factor for bearing at bolt holes
8 / 10
Project:
Project no:
Author:
Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
SP2 Rafter-1-tfl 1 E70xx ◢3.5◣ ◢5.0◣ 199 33 LE3 19.3 25.5 75.7 OK
E70xx ◢3.5◣ ◢5.0◣ 199 33 LE1 19.4 25.5 76.0 OK
SP2 Rafter-1-bfl 1 E70xx ◢3.5◣ ◢5.0◣ 200 33 LE4 18.7 24.9 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 200 33 LE4 18.9 25.2 75.1 OK
SP2 Rafter-1-w 1 E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 16.9 25.6 65.8 OK
E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 16.9 25.6 66.1 OK
SP1 Rafter-2-tfl 1 E70xx ◢3.5◣ ◢5.0◣ 199 33 LE3 19.2 25.5 75.4 OK
E70xx ◢3.5◣ ◢5.0◣ 200 33 LE1 19.3 25.5 75.8 OK
SP1 Rafter-2-bfl 1 E70xx ◢3.5◣ ◢5.0◣ 200 33 LE2 18.8 25.0 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 200 33 LE2 18.9 25.2 75.1 OK
SP1 Rafter-2-w 1 E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 16.5 25.6 64.4 OK
E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 16.7 25.6 65.4 OK
SP2 RIB1 E70xx ◢3.5◣ ◢5.0◣ 95 10 LE2 3.5 7.2 49.3 OK
E70xx ◢3.5◣ ◢5.0◣ 95 10 LE2 3.5 7.2 48.3 OK
Rafter-1-bfl 1 RIB1 E70xx ◢3.5◣ ◢5.0◣ 150 10 LE2 5.3 6.8 76.8 OK
E70xx ◢3.5◣ ◢5.0◣ 150 10 LE2 5.2 6.8 76.7 OK
SP2 RIB2 E70xx ◢3.5◣ ◢5.0◣ 99 10 LE3 5.6 7.4 75.2 OK
E70xx ◢3.5◣ ◢5.0◣ 99 10 LE3 5.6 7.4 75.3 OK
Rafter-1-tfl 1 RIB2 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE3 5.2 6.7 77.1 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE3 5.2 6.7 77.1 OK
SP1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 99 10 LE1 5.7 7.6 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 99 10 LE2 4.9 6.5 75.2 OK
Rafter-2-tfl 1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.1 6.7 77.1 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.1 6.7 77.1 OK
SP1 RIB4 E70xx ◢3.5◣ ◢5.0◣ 97 10 LE4 3.5 7.3 48.0 OK
E70xx ◢3.5◣ ◢5.0◣ 97 10 LE4 3.4 7.4 46.7 OK
Rafter-2-bfl 1 RIB4 E70xx ◢3.5◣ ◢5.0◣ 150 10 LE4 5.3 6.9 77.2 OK
E70xx ◢3.5◣ ◢5.0◣ 150 10 LE4 5.3 6.8 77.2 OK
CPL3 Strut-2-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.7 7.1 38.3 OK
CPL3 Strut-2-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.7 7.5 35.6 OK
CPL3 Strut-2-w 3 E70xx ◢3.5 ◢5.0 149 10 LE3 2.9 7.4 38.8 OK
CPL3 Strut-2-w 3 E70xx ◢3.5 ◢5.0 149 10 LE3 2.9 7.2 39.9 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE2 2.7 7.2 37.9 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.8 7.5 37.8 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE4 2.7 7.4 36.9 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE4 2.8 7.1 40.0 OK
9 / 10
Project:
Project no:
Author:
Where:
Fnw = 387.6 MPa – nominal stress of weld material:
Buckling
Buckling analysis was not calculated.
10 / 10
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.04
Analysis Stress, strain/ simplified loading
Design code AISC - ASD 2016
1 / 12
Project:
Project no:
Author:
2 / 12
Project:
Project no:
Author:
Cross-sections
Name Material
7 - Iwn532x(250/250) ST52
8 - Iwn520x(200/200) ST52
5 - RHS125x125 ST37
10 - IPE240 ST37
3 / 12
Project:
Project no:
Author:
Cross-sections
Name Material Drawing
7 - Iwn532x(250/250) ST52
8 - Iwn520x(200/200) ST52
5 - RHS125x125 ST37
10 - IPE240 ST37
4 / 12
Project:
Project no:
Author:
Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M16 Grade8.8 M16 Grade8.8 16 800.0 201
M22 Grade8.8 M22 Grade8.8 22 800.0 380
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.6 < 5.0% OK
Bolts 77.7 < 100% OK
Welds 78.3 < 100% OK
Buckling Not calculated
5 / 12
Project:
Project no:
Author:
Plates
fy Thickness σEd εPl σcEd
Name Material Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Column -tfl 1 ST52 360.0 20.0 LE1 183.1 0.0 19.4 OK
Column -bfl 1 ST52 360.0 12.0 LE1 135.4 0.0 0.0 OK
Column -w 1 ST52 360.0 10.0 LE3 168.1 0.0 0.0 OK
Rafter-tfl 1 ST52 360.0 10.0 LE3 154.2 0.0 0.0 OK
Rafter-bfl 1 ST52 360.0 10.0 LE4 158.8 0.0 0.0 OK
Rafter-w 1 ST52 360.0 6.0 LE4 150.0 0.0 0.0 OK
Strut-1 ST37 240.0 4.0 LE2 124.8 0.0 0.0 OK
Hanging Beam-bfl 1 ST37 240.0 9.8 LE1 33.2 0.0 0.0 OK
Hanging Beam-tfl 1 ST37 240.0 9.8 LE2 50.2 0.0 0.0 OK
Hanging Beam-w 1 ST37 240.0 6.2 LE2 144.9 0.6 22.1 OK
SP6 ST52 360.0 10.0 LE3 104.3 0.0 10.5 OK
CPL2 ST52 360.0 10.0 LE3 102.5 0.0 10.5 OK
EP1 ST52 360.0 20.0 LE3 156.6 0.0 28.1 OK
SP3 ST52 360.0 10.0 LE3 113.9 0.0 0.0 OK
SP4 ST52 360.0 10.0 LE4 92.2 0.0 0.0 OK
SP7 ST52 360.0 10.0 LE2 74.8 0.0 0.0 OK
RIB1 ST52 360.0 10.0 LE2 205.3 0.1 0.0 OK
RIB2 ST52 360.0 10.0 LE3 184.3 0.0 0.0 OK
SP8 ST52 360.0 10.0 LE3 153.4 0.0 0.0 OK
FP1 ST52 360.0 10.0 LE3 176.1 0.0 24.7 OK
RIB3 ST52 360.0 10.0 LE3 95.1 0.0 0.0 OK
Design data
fy εlim
Material
[MPa] [%]
ST52 360.0 5.0
ST37 240.0 5.0
6 / 12
Project:
Project no:
Author:
7 / 12
Project:
Project no:
Author:
8 / 12
Project:
Project no:
Author:
Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 M16 Grade8.8 - 1 LE3 3.2 2.2 99.8 5.3 6.0 - OK
Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
M16 Grade8.8 - 1 60.3 36.2
M22 Grade8.8 - 2 114.0 68.4
Where:
Fnt = 600.0 MPa – nominal tensile stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
9 / 12
Project:
Project no:
Author:
Where:
Fnv = 360.0 MPa – nominal shear stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 274.6 kN ≥ V = 1.4 kN
Where:
lc = 87 mm – clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 20 mm – thickness of the plate
d = 22 mm – diameter of a bolt
Fu = 520.0 MPa – tensile strength of the connected material
Ω = 2.00 – safety factor for bearing at bolt holes
10 / 12
Project:
Project no:
Author:
Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE2 2.7 7.2 37.8 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE2 2.7 7.5 35.3 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE3 2.6 7.5 34.6 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE3 2.8 7.2 39.5 OK
Column -w 1 SP6 E70xx ◢3.5◣ ◢5.0◣ 259 16 LE4 4.8 10.6 45.7 OK
E70xx ◢3.5◣ ◢5.0◣ 259 16 LE1 4.7 9.9 46.9 OK
EP1 Rafter-tfl 1 E70xx ◢5.7◣ ◢8.0◣ 200 50 LE1 45.5 60.9 74.7 OK
E70xx ◢5.7◣ ◢8.0◣ 200 50 LE1 42.4 60.9 69.7 OK
EP1 Rafter-bfl 1 E70xx ◢5.7◣ ◢8.0◣ 200 50 LE4 31.8 60.6 52.5 OK
E70xx ◢5.7◣ ◢8.0◣ 200 50 LE4 33.5 59.8 55.9 OK
EP1 Rafter-w 1 E70xx ◢3.5◣ ◢5.0◣ 501 46 LE3 20.2 35.0 57.7 OK
E70xx ◢3.5◣ ◢5.0◣ 501 46 LE1 20.1 35.0 57.6 OK
SP3 Column -w 1 E70xx ◢3.5◣ ◢5.0◣ 501 33 LE1 17.7 23.7 74.4 OK
E70xx ◢3.5◣ ◢5.0◣ 501 33 LE3 17.8 23.7 75.0 OK
SP3 Column -bfl 1 E70xx ◢3.5 ◢5.0 249 31 LE3 4.0 23.4 17.1 OK
Column -tfl 1 SP3 E70xx ◢3.5◣ ◢5.0◣ 249 31 LE3 17.9 23.9 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 249 31 LE3 17.8 23.8 75.1 OK
EP1 RIB1 E70xx ◢5.7◣ ◢8.0◣ 99 10 LE2 9.0 12.0 75.1 OK
E70xx ◢5.7◣ ◢8.0◣ 99 10 LE4 8.9 11.9 75.2 OK
Rafter-bfl 1 RIB1 E70xx ◢5.7◣ ◢8.0◣ 149 10 LE2 8.4 11.3 75.1 OK
E70xx ◢5.7◣ ◢8.0◣ 149 10 LE4 8.4 11.2 75.1 OK
EP1 RIB2 E70xx ◢5.7◣ ◢8.0◣ 99 10 LE3 6.9 11.1 62.2 OK
E70xx ◢5.7◣ ◢8.0◣ 99 10 LE1 6.7 10.1 66.6 OK
Rafter-tfl 1 RIB2 E70xx ◢5.7◣ ◢8.0◣ 150 10 LE3 7.9 10.5 75.3 OK
E70xx ◢5.7◣ ◢8.0◣ 150 10 LE1 7.9 10.5 75.3 OK
SP3 SP8 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.5 7.0 78.3 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE3 5.5 7.0 78.3 OK
Column -tfl 1 SP8 E70xx ◢3.5◣ ◢5.0◣ 107 10 LE1 5.6 7.4 75.3 OK
E70xx ◢3.5◣ ◢5.0◣ 107 10 LE3 5.6 7.5 75.3 OK
Column -w 1 SP4 E70xx ◢3.5◣ ◢5.0◣ 498 31 LE4 6.0 19.9 30.0 OK
E70xx ◢3.5◣ ◢5.0◣ 499 31 LE4 3.9 17.9 21.6 OK
Column -bfl 1 SP4 E70xx ◢3.5◣ ◢5.0◣ 118 29 LE3 7.1 22.6 31.2 OK
E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 3.5 22.5 15.7 OK
Column -tfl 1 SP4 E70xx ◢3.5◣ ◢5.0◣ 118 29 LE2 10.2 22.5 45.5 OK
E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 12.8 22.1 57.8 OK
Column -tfl 1 SP7 E70xx ◢3.5◣ ◢5.0◣ 118 29 LE4 12.1 22.5 53.7 OK
E70xx ◢3.5◣ ◢5.0◣ 118 29 LE2 11.7 22.5 51.8 OK
Column -bfl 1 SP7 E70xx ◢3.5◣ ◢5.0◣ 118 29 LE1 7.0 22.6 31.1 OK
E70xx ◢3.5◣ ◢5.0◣ 118 29 LE2 3.5 22.5 15.4 OK
11 / 12
Project:
Project no:
Author:
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
Column -w 1 SP7 E70xx ◢3.5◣ ◢5.0◣ 499 31 LE4 5.4 19.8 27.2 OK
E70xx ◢3.5◣ ◢5.0◣ 498 31 LE4 5.0 20.6 24.4 OK
Column -tfl 1 FP1 E70xx ◢3.5◣ ◢5.0◣ 199 13 LE1 7.6 10.1 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 199 13 LE4 6.3 9.4 66.7 OK
FP1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 209 13 LE3 5.7 9.4 60.4 OK
E70xx ◢3.5◣ ◢5.0◣ 209 13 LE1 5.5 9.6 57.6 OK
Column -tfl 1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 99 12 LE4 4.8 6.4 74.9 OK
E70xx ◢3.5◣ ◢5.0◣ 100 12 LE3 5.3 8.3 64.1 OK
Where:
Fnw = 398.9 MPa – nominal stress of weld material:
Buckling
Buckling analysis was not calculated.
12 / 12
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.05
Analysis Stress, strain/ simplified loading
Design code AISC - ASD 2016
1 / 11
Project:
Project no:
Author:
2 / 11
Project:
Project no:
Author:
Cross-sections
Name Material
8 - Iwn320x(200/200) ST52
5 - RHS150x150 ST37
10 - IPE240 ST37
3 / 11
Project:
Project no:
Author:
Cross-sections
Name Material Drawing
8 - Iwn320x(200/200) ST52
5 - RHS150x150 ST37
10 - IPE240 ST37
Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M22 Grade8.8 M22 Grade8.8 22 800.0 380
M16 Grade 8.8 M16 Grade 8.8 16 800.0 201
4 / 11
Project:
Project no:
Author:
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.0 < 5.0% OK
Bolts 71.2 < 100% OK
Welds 77.6 < 100% OK
Buckling Not calculated
5 / 11
Project:
Project no:
Author:
Plates
fy Thickness σEd εPl σcEd
Name Material Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Rafter-1-tfl 1 ST52 360.0 10.0 LE3 139.3 0.0 0.0 OK
Rafter-1-bfl 1 ST52 360.0 10.0 LE2 125.8 0.0 0.0 OK
Rafter-1-w 1 ST52 360.0 6.0 LE3 113.4 0.0 0.0 OK
Rafter-2-tfl 1 ST52 360.0 10.0 LE1 180.8 0.0 0.0 OK
Rafter-2-bfl 1 ST52 360.0 10.0 LE2 150.9 0.0 0.0 OK
Rafter-2-w 1 ST52 360.0 6.0 LE1 136.3 0.0 0.0 OK
Strut-1 ST37 240.0 4.5 LE1 108.1 0.0 0.0 OK
Post-bfl 1 ST37 240.0 9.8 LE1 6.9 0.0 0.0 OK
Post-tfl 1 ST37 240.0 9.8 LE1 2.6 0.0 0.0 OK
Post-w 1 ST37 240.0 6.2 LE4 28.9 0.0 2.9 OK
SP1 ST52 360.0 20.0 LE3 153.3 0.0 18.5 OK
SP2 ST52 360.0 20.0 LE3 152.5 0.0 16.7 OK
RIB1 ST52 360.0 10.0 LE3 148.2 0.0 0.0 OK
RIB2 ST52 360.0 10.0 LE2 138.4 0.0 0.0 OK
RIB3 ST52 360.0 10.0 LE3 150.8 0.0 0.0 OK
RIB4 ST52 360.0 10.0 LE2 146.0 0.0 0.0 OK
CPL2 ST52 360.0 10.0 LE3 121.7 0.0 11.2 OK
Design data
fy εlim
Material
[MPa] [%]
ST52 360.0 5.0
ST37 240.0 5.0
6 / 11
Project:
Project no:
Author:
7 / 11
Project:
Project no:
Author:
Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 M22 Grade8.8 - 1 LE3 63.9 2.0 237.1 56.0 2.9 - OK
B2 M22 Grade8.8 - 1 LE3 75.3 3.1 237.3 66.0 4.6 - OK
B3 M22 Grade8.8 - 1 LE1 69.8 1.4 274.6 61.3 2.0 - OK
B4 M22 Grade8.8 - 1 LE3 81.1 4.2 274.6 71.2 6.1 - OK
B5 M22 Grade8.8 - 1 LE3 3.4 1.3 274.6 3.0 1.9 - OK
B6 M22 Grade8.8 - 1 LE1 3.2 4.1 274.6 2.8 6.0 - OK
B7 M22 Grade8.8 - 1 LE1 0.0 1.5 274.6 0.0 2.2 - OK
B8 M22 Grade8.8 - 1 LE1 0.0 2.8 258.4 0.0 4.2 - OK
B13 M16 Grade 8.8 - 2 LE3 0.5 2.0 42.9 0.9 5.4 - OK
B14 M16 Grade 8.8 - 2 LE2 0.9 3.2 42.9 1.5 8.7 - OK
B15 M16 Grade 8.8 - 2 LE2 0.5 1.4 42.9 0.9 3.7 - OK
B16 M16 Grade 8.8 - 2 LE2 0.9 2.8 42.9 1.6 7.8 - OK
B9 M16 Grade 8.8 - 2 LE4 1.0 3.2 99.8 1.7 8.9 - OK
B10 M16 Grade 8.8 - 2 LE3 7.8 2.6 99.8 12.9 7.1 - OK
B11 M16 Grade 8.8 - 2 LE1 0.4 2.6 96.6 0.7 7.3 - OK
B12 M16 Grade 8.8 - 2 LE2 0.8 2.1 99.8 1.3 5.8 - OK
8 / 11
Project:
Project no:
Author:
Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
M22 Grade8.8 - 1 114.0 68.4
M16 Grade 8.8 - 2 60.3 36.2
Where:
Fnt = 600.0 MPa – nominal tensile stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Where:
Fnv = 360.0 MPa – nominal shear stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 274.6 kN ≥ V = 4.2 kN
Where:
lc = 76 mm – clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 20 mm – thickness of the plate
d = 22 mm – diameter of a bolt
Fu = 520.0 MPa – tensile strength of the connected material
Ω = 2.00 – safety factor for bearing at bolt holes
9 / 11
Project:
Project no:
Author:
Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
SP2 Rafter-1-tfl 1 E70xx ◢3.5◣ ◢5.0◣ 200 40 LE3 23.4 30.6 76.3 OK
E70xx ◢3.5◣ ◢5.0◣ 200 40 LE3 23.5 30.7 76.5 OK
SP2 Rafter-1-bfl 1 E70xx ◢3.5◣ ◢5.0◣ 200 40 LE2 22.7 30.2 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 200 40 LE4 22.8 30.4 75.2 OK
SP2 Rafter-1-w 1 E70xx ◢3.5◣ ◢5.0◣ 301 38 LE1 17.3 28.6 60.6 OK
E70xx ◢3.5◣ ◢5.0◣ 301 38 LE1 17.9 28.9 62.1 OK
SP1 Rafter-2-tfl 1 E70xx ◢3.5◣ ◢5.0◣ 199 33 LE1 19.6 25.5 76.8 OK
E70xx ◢3.5◣ ◢5.0◣ 199 33 LE1 19.8 25.5 77.6 OK
SP1 Rafter-2-bfl 1 E70xx ◢3.5◣ ◢5.0◣ 199 33 LE4 19.1 25.4 75.3 OK
E70xx ◢3.5◣ ◢5.0◣ 200 33 LE4 19.1 25.3 75.5 OK
SP1 Rafter-2-w 1 E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 16.9 25.6 65.9 OK
E70xx ◢3.5◣ ◢5.0◣ 301 33 LE3 18.6 25.1 74.0 OK
SP2 RIB1 E70xx ◢3.5◣ ◢5.0◣ 99 10 LE3 5.2 7.3 70.9 OK
E70xx ◢3.5◣ ◢5.0◣ 99 10 LE3 5.4 7.2 75.1 OK
Rafter-1-tfl 1 RIB1 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE3 5.2 6.7 77.0 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE3 5.2 6.7 77.1 OK
SP2 RIB2 E70xx ◢3.5◣ ◢5.0◣ 298 19 LE4 7.2 14.1 51.1 OK
E70xx ◢3.5◣ ◢5.0◣ 298 19 LE2 6.5 14.2 46.0 OK
Rafter-1-bfl 1 RIB2 E70xx ◢3.5◣ ◢5.0◣ 150 19 LE2 9.4 12.4 76.4 OK
E70xx ◢3.5◣ ◢5.0◣ 150 19 LE2 9.3 12.2 76.3 OK
SP1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 99 10 LE3 5.7 7.6 75.2 OK
E70xx ◢3.5◣ ◢5.0◣ 99 10 LE1 5.7 7.6 75.1 OK
Rafter-2-tfl 1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.1 6.6 77.1 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.2 6.7 77.4 OK
SP1 RIB4 E70xx ◢3.5◣ ◢5.0◣ 90 10 LE4 5.6 7.4 75.0 OK
E70xx ◢3.5◣ ◢5.0◣ 90 10 LE2 5.6 7.4 75.0 OK
Rafter-2-bfl 1 RIB4 E70xx ◢3.5◣ ◢5.0◣ 150 10 LE4 5.3 6.9 77.5 OK
E70xx ◢3.5◣ ◢5.0◣ 150 10 LE4 5.2 6.8 77.1 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.8 7.1 39.3 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.5 7.6 33.7 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE3 2.5 7.5 33.1 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE4 2.9 7.1 41.4 OK
10 / 11
Project:
Project no:
Author:
Where:
Fnw = 434.2 MPa – nominal stress of weld material:
Buckling
Buckling analysis was not calculated.
11 / 11
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.06
Analysis Stress, strain/ simplified loading
Design code AISC - ASD 2016
1/8
Project:
Project no:
Author:
2/8
Project:
Project no:
Author:
Cross-sections
Name Material
10 - IPE240 ST37
Cross-sections
Name Material Drawing
10 - IPE240 ST37
Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M16 Grade 8.8 M16 Grade 8.8 16 800.0 201
3/8
Project:
Project no:
Author:
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.1 < 5.0% OK
Bolts 59.4 < 100% OK
Welds 36.7 < 100% OK
Buckling Not calculated
Plates
fy Thickness σEd εPl σcEd
Name Material Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Post-bfl 1 ST37 240.0 9.8 LE1 1.1 0.0 0.0 OK
Post-tfl 1 ST37 240.0 9.8 LE1 1.1 0.0 0.0 OK
Post-w 1 ST37 240.0 6.2 LE1 8.9 0.0 0.0 OK
Hanging Beam-1-bfl 1 ST37 240.0 9.8 LE1 30.9 0.0 0.0 OK
Hanging Beam-1-tfl 1 ST37 240.0 9.8 LE1 27.1 0.0 0.0 OK
Hanging Beam-1-w 1 ST37 240.0 6.2 LE1 144.0 0.1 12.4 OK
Hanging Beam-2-bfl 1 ST37 240.0 9.8 LE1 30.9 0.0 0.0 OK
Hanging Beam-2-tfl 1 ST37 240.0 9.8 LE1 27.1 0.0 0.0 OK
Hanging Beam-2-w 1 ST37 240.0 6.2 LE1 144.0 0.1 12.4 OK
FP1 ST52 360.0 10.0 LE1 127.2 0.0 12.4 OK
FP2 ST52 360.0 10.0 LE1 127.2 0.0 12.4 OK
SP1 ST37 240.0 10.0 LE1 36.3 0.0 0.0 OK
SP2 ST37 240.0 10.0 LE1 36.2 0.0 0.0 OK
Design data
fy εlim
Material
[MPa] [%]
ST37 240.0 5.0
ST52 360.0 5.0
4/8
Project:
Project no:
Author:
5/8
Project:
Project no:
Author:
Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 M16 Grade 8.8 - 1 LE1 3.5 20.5 42.9 5.8 56.7 - OK
Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
M16 Grade 8.8 - 1 60.3 36.2
6/8
Project:
Project no:
Author:
Where:
Fnt = 600.0 MPa – nominal tensile stress from AISC 360-16 Table J3.2
Ab = 201 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Where:
Fnv = 360.0 MPa – nominal shear stress from AISC 360-16 Table J3.2
Ab = 201 mm2 – gross bolt cross-sectional area
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 42.9 kN ≥ V = 21.5 kN
Where:
lc = 82 mm – clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 6 mm – thickness of the plate
d = 16 mm – diameter of a bolt
Fu = 360.0 MPa – tensile strength of the connected material
Ω = 2.00 – safety factor for bearing at bolt holes
7/8
Project:
Project no:
Author:
Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
Post-w 1 FP1 E70xx ◢3.5◣ ◢5.0◣ 169 13 LE1 3.7 10.0 36.7 OK
E70xx ◢3.5◣ ◢5.0◣ 169 13 LE1 3.6 9.9 36.5 OK
Post-w 1 FP2 E70xx ◢3.5◣ ◢5.0◣ 169 13 LE1 3.7 10.0 36.7 OK
E70xx ◢3.5◣ ◢5.0◣ 169 13 LE1 3.6 9.9 36.5 OK
Post-w 1 SP1 E70xx ◢3.5◣ ◢5.0◣ 87 12 LE1 2.4 9.4 25.4 OK
E70xx ◢3.5◣ ◢5.0◣ 87 12 LE1 2.4 9.4 25.1 OK
FP1 SP1 E70xx ◢3.5◣ ◢5.0◣ 209 13 LE1 1.1 9.2 12.0 OK
E70xx ◢3.5◣ ◢5.0◣ 209 13 LE1 1.1 9.1 12.5 OK
Post-w 1 SP2 E70xx ◢3.5◣ ◢5.0◣ 87 12 LE1 2.4 9.4 25.2 OK
E70xx ◢3.5◣ ◢5.0◣ 87 12 LE1 2.4 9.4 25.4 OK
FP2 SP2 E70xx ◢3.5◣ ◢5.0◣ 209 13 LE1 1.1 9.1 12.5 OK
E70xx ◢3.5◣ ◢5.0◣ 209 13 LE1 1.1 9.2 12.0 OK
Where:
Fnw = 434.3 MPa – nominal stress of weld material:
Buckling
Buckling analysis was not calculated.
8/8
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.07
Analysis Stress, strain/ simplified loading
Design code AISC - ASD 2016
1 / 13
Project:
Project no:
Author:
2 / 13
Project:
Project no:
Author:
Cross-sections
Name Material
7 - General ST52, ST52, ST52, ST52, ST52
8 - Iwn520x(200/200) ST52
5 - RHS125x125 ST37
9 - Iwn320x(200/200) ST52
3 / 13
Project:
Project no:
Author:
Cross-sections
Name Material Drawing
8 - Iwn520x(200/200) ST52
5 - RHS125x125 ST37
9 - Iwn320x(200/200) ST52
4 / 13
Project:
Project no:
Author:
Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M16 Grade8.8 M16 Grade8.8 16 800.0 201
M22 Grade8.8 M22 Grade8.8 22 800.0 380
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.1 < 5.0% OK
Bolts 79.0 < 100% OK
Welds 77.9 < 100% OK
Buckling Not calculated
5 / 13
Project:
Project no:
Author:
Plates
fy Thickness σEd εPl σcEd
Name Material Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Column -bfl 1 ST52 360.0 12.0 LE1 178.6 0.0 0.0 OK
Column -bfl 2 ST52 360.0 10.0 LE2 172.3 0.0 0.0 OK
Column -bfl 3 ST52 360.0 20.0 LE1 180.2 0.0 23.0 OK
Column -bfl 4 ST52 360.0 6.0 LE1 99.6 0.0 0.0 OK
Column -bfl 5 ST52 360.0 12.0 LE1 197.1 0.0 22.5 OK
Rafter-tfl 1 ST52 360.0 10.0 LE1 154.6 0.0 0.0 OK
Rafter-bfl 1 ST52 360.0 10.0 LE2 159.9 0.0 0.0 OK
Rafter-w 1 ST52 360.0 6.0 LE2 147.1 0.0 0.0 OK
Strut ST37 240.0 4.0 LE2 126.4 0.0 0.0 OK
Beam-tfl 1 ST52 360.0 10.0 LE1 57.5 0.0 0.0 OK
Beam-bfl 1 ST52 360.0 10.0 LE2 62.9 0.0 0.0 OK
Beam-w 1 ST52 360.0 6.0 LE2 53.7 0.0 0.0 OK
Brace ST37 240.0 4.0 LE1 45.6 0.0 0.0 OK
SP6 ST52 360.0 10.0 LE2 97.0 0.0 9.5 OK
CPL2 ST52 360.0 10.0 LE1 98.5 0.0 8.8 OK
EP1 ST52 360.0 20.0 LE1 145.8 0.0 33.5 OK
SP3 ST52 360.0 10.0 LE1 117.1 0.0 0.0 OK
RIB1 ST52 360.0 10.0 LE2 210.5 0.1 0.0 OK
RIB2 ST52 360.0 10.0 LE1 184.7 0.0 0.0 OK
SP8 ST52 360.0 10.0 LE1 152.4 0.0 0.0 OK
EP2 ST52 360.0 20.0 LE1 71.2 0.0 22.5 OK
RIB3 ST52 360.0 10.0 LE1 94.5 0.0 0.0 OK
RIB4 ST52 360.0 10.0 LE2 122.7 0.0 0.0 OK
SP4 ST52 360.0 10.0 LE1 38.7 0.0 2.2 OK
CPL3 ST52 360.0 10.0 LE1 30.0 0.0 2.2 OK
SP5 ST52 360.0 10.0 LE2 103.2 0.0 0.0 OK
SP7 ST52 360.0 10.0 LE2 62.0 0.0 0.0 OK
Design data
fy εlim
Material
[MPa] [%]
ST52 360.0 5.0
ST37 240.0 5.0
6 / 13
Project:
Project no:
Author:
7 / 13
Project:
Project no:
Author:
8 / 13
Project:
Project no:
Author:
Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 M16 Grade8.8 - 1 LE1 2.9 1.9 65.7 4.8 5.3 - OK
Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
M16 Grade8.8 - 1 60.3 36.2
M22 Grade8.8 - 2 114.0 68.4
9 / 13
Project:
Project no:
Author:
Where:
Fnt = 600.0 MPa – nominal tensile stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Where:
Fnv = 360.0 MPa – nominal shear stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 274.6 kN ≥ V = 1.8 kN
Where:
lc = 58 mm – clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 20 mm – thickness of the plate
d = 22 mm – diameter of a bolt
Fu = 520.0 MPa – tensile strength of the connected material
Ω = 2.00 – safety factor for bearing at bolt holes
10 / 13
Project:
Project no:
Author:
Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
CPL2 Strut-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 3.1 7.2 43.2 OK
CPL2 Strut-w 1 E70xx ◢3.5 ◢5.0 149 10 LE2 2.6 7.3 35.8 OK
CPL2 Strut-w 3 E70xx ◢3.5 ◢5.0 149 10 LE1 2.7 7.3 37.3 OK
CPL2 Strut-w 3 E70xx ◢3.5 ◢5.0 149 10 LE2 3.2 7.2 44.0 OK
EP1 Rafter-tfl 1 E70xx ◢5.7◣ ◢8.0◣ 200 50 LE1 45.8 61.0 75.0 OK
E70xx ◢5.7◣ ◢8.0◣ 200 50 LE1 44.1 60.8 72.5 OK
EP1 Rafter-bfl 1 E70xx ◢5.7◣ ◢8.0◣ 200 50 LE2 37.7 60.0 62.8 OK
E70xx ◢5.7◣ ◢8.0◣ 200 50 LE2 34.7 61.3 56.6 OK
EP1 Rafter-w 1 E70xx ◢3.5◣ ◢5.0◣ 501 46 LE1 19.7 35.0 56.3 OK
E70xx ◢3.5◣ ◢5.0◣ 501 46 LE1 19.5 34.9 55.8 OK
EP1 RIB1 E70xx ◢5.7◣ ◢8.0◣ 99 10 LE2 9.1 12.0 75.6 OK
E70xx ◢5.7◣ ◢8.0◣ 99 10 LE2 9.0 12.0 75.6 OK
Rafter-bfl 1 RIB1 E70xx ◢5.7◣ ◢8.0◣ 149 10 LE2 8.4 11.2 75.2 OK
E70xx ◢5.7◣ ◢8.0◣ 149 10 LE2 8.5 11.3 75.2 OK
EP1 RIB2 E70xx ◢5.7◣ ◢8.0◣ 99 10 LE1 6.6 11.3 58.4 OK
E70xx ◢5.7◣ ◢8.0◣ 99 10 LE1 6.7 10.1 66.6 OK
Rafter-tfl 1 RIB2 E70xx ◢5.7◣ ◢8.0◣ 150 10 LE1 7.9 10.5 75.3 OK
E70xx ◢5.7◣ ◢8.0◣ 150 10 LE1 7.9 10.5 75.3 OK
Column -bfl 2 SP6 E70xx ◢3.5◣ ◢5.0◣ 259 16 LE1 6.0 10.5 56.6 OK
E70xx ◢3.5◣ ◢5.0◣ 259 16 LE1 3.8 11.1 34.1 OK
SP3 Column -bfl 2 E70xx ◢3.5◣ ◢5.0◣ 501 33 LE1 18.1 24.5 74.1 OK
E70xx ◢3.5◣ ◢5.0◣ 501 33 LE1 15.0 23.3 64.1 OK
SP3 Column -bfl 1 E70xx ◢3.5 ◢5.0 249 31 LE1 5.0 21.5 23.3 OK
SP3 Column -bfl 5 E70xx ◢3.5 ◢5.0 251 31 LE2 3.1 20.0 15.7 OK
SP3 Column -bfl 4 E70xx ◢3.5◣ ◢5.0◣ 249 31 LE2 5.6 17.9 31.2 OK
E70xx ◢3.5◣ ◢5.0◣ 249 31 LE1 4.0 17.5 23.1 OK
Column -bfl 3 SP3 E70xx ◢3.5◣ ◢5.0◣ 232 33 LE1 19.1 25.5 75.2 OK
E70xx ◢3.5◣ ◢5.0◣ 232 33 LE1 19.0 25.3 75.1 OK
Column -bfl 3 SP8 E70xx ◢3.5◣ ◢5.0◣ 103 10 LE1 5.9 7.9 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 103 10 LE1 5.9 7.9 75.2 OK
SP3 SP8 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.4 7.0 77.9 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.4 7.0 77.8 OK
EP2 Beam-tfl 1 E70xx ◢5.7◣ ◢8.0◣ 199 33 LE1 8.7 40.2 21.6 OK
E70xx ◢5.7◣ ◢8.0◣ 199 33 LE1 8.4 40.8 20.5 OK
EP2 Beam-bfl 1 E70xx ◢5.7◣ ◢8.0◣ 200 33 LE2 6.2 40.5 15.3 OK
E70xx ◢5.7◣ ◢8.0◣ 200 33 LE2 8.2 39.1 20.9 OK
EP2 Beam-w 1 E70xx ◢3.5◣ ◢5.0◣ 300 33 LE2 5.5 21.2 25.9 OK
E70xx ◢3.5◣ ◢5.0◣ 300 33 LE1 5.8 20.7 28.2 OK
EP2 RIB3 E70xx ◢3.5◣ ◢5.0◣ 99 10 LE2 3.4 6.8 49.5 OK
11 / 13
Project:
Project no:
Author:
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
E70xx ◢3.5◣ ◢5.0◣ 99 10 LE1 3.7 6.7 55.1 OK
Beam-tfl 1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.0 6.7 75.0 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.0 6.7 75.0 OK
EP2 RIB4 E70xx ◢3.5◣ ◢5.0◣ 100 10 LE1 5.6 7.4 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 100 10 LE1 5.6 7.4 75.1 OK
Beam-bfl 1 RIB4 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.2 6.8 75.3 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE2 5.1 6.8 75.3 OK
Column -bfl 2 SP4 E70xx ◢3.5◣ ◢5.0◣ 345 22 LE1 2.5 13.9 18.1 OK
E70xx ◢3.5◣ ◢5.0◣ 346 22 LE1 2.3 13.9 16.4 OK
Column -bfl 4 SP4 E70xx ◢3.5◣ ◢5.0◣ 249 21 LE1 1.3 11.1 11.6 OK
E70xx ◢3.5◣ ◢5.0◣ 249 21 LE1 3.5 11.1 31.7 OK
Column -bfl 5 SP4 E70xx ◢3.5◣ ◢5.0◣ 122 20 LE1 2.6 12.0 21.5 OK
E70xx ◢3.5◣ ◢5.0◣ 122 20 LE1 3.9 14.8 26.3 OK
Column -bfl 3 SP4 E70xx ◢3.5◣ ◢5.0◣ 102 20 LE1 3.7 14.9 24.8 OK
E70xx ◢3.5◣ ◢5.0◣ 102 20 LE2 2.3 15.3 15.2 OK
CPL3 Brace-w 2 E70xx ◢3.5 ◢5.0 149 10 LE2 0.5 5.5 9.3 OK
CPL3 Brace-w 2 E70xx ◢3.5 ◢5.0 149 10 LE2 0.5 6.9 8.0 OK
CPL3 Brace-w 4 E70xx ◢3.5 ◢5.0 149 10 LE1 0.9 6.9 13.0 OK
CPL3 Brace-w 4 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.4 12.9 OK
Column -bfl 2 SP5 E70xx ◢3.5◣ ◢5.0◣ 346 22 LE2 9.3 12.2 75.6 OK
E70xx ◢3.5◣ ◢5.0◣ 346 22 LE2 9.2 12.1 75.5 OK
Column -bfl 4 SP5 E70xx ◢3.5◣ ◢5.0◣ 249 21 LE2 3.0 13.9 21.3 OK
E70xx ◢3.5◣ ◢5.0◣ 249 21 LE2 3.7 14.8 24.9 OK
Column -bfl 5 SP5 E70xx ◢3.5◣ ◢5.0◣ 122 20 LE2 5.4 12.3 44.3 OK
E70xx ◢3.5◣ ◢5.0◣ 122 20 LE1 4.8 11.9 40.2 OK
Column -bfl 3 SP5 E70xx ◢3.5◣ ◢5.0◣ 116 23 LE2 6.8 13.5 50.5 OK
E70xx ◢3.5◣ ◢5.0◣ 116 23 LE2 8.8 14.7 59.6 OK
Column -bfl 4 SP7 E70xx ◢3.5◣ ◢5.0◣ 248 16 LE1 1.4 11.9 11.9 OK
E70xx ◢3.5◣ ◢5.0◣ 248 16 LE2 2.1 11.7 17.7 OK
Column -bfl 2 SP7 E70xx ◢3.5◣ ◢5.0◣ 147 16 LE2 2.5 11.0 22.7 OK
E70xx ◢3.5◣ ◢5.0◣ 147 16 LE1 3.8 10.2 37.4 OK
Column -bfl 5 SP7 E70xx ◢3.5◣ ◢5.0◣ 102 15 LE1 1.7 10.6 15.8 OK
E70xx ◢3.5◣ ◢5.0◣ 102 15 LE2 3.6 11.1 32.1 OK
Column -bfl 1 SP7 E70xx ◢3.5◣ ◢5.0◣ 120 15 LE1 2.9 9.7 29.7 OK
E70xx ◢3.5◣ ◢5.0◣ 120 15 LE2 3.0 10.2 29.2 OK
12 / 13
Project:
Project no:
Author:
Where:
Fnw = 397.9 MPa – nominal stress of weld material:
Buckling
Buckling analysis was not calculated.
13 / 13
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.08
Analysis Stress, strain/ simplified loading
Design code AISC - ASD 2016
1 / 11
Project:
Project no:
Author:
2 / 11
Project:
Project no:
Author:
Cross-sections
Name Material
6 - Iwn320x(200/200) ST52
5 - RHS125x125 ST37
3 / 11
Project:
Project no:
Author:
Cross-sections
Name Material Drawing
6 - Iwn320x(200/200) ST52
5 - RHS125x125 ST37
Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M22 Grade8.8 M22 Grade8.8 22 800.0 380
M16 Grade 8.8 M16 Grade 8.8 16 800.0 201
4 / 11
Project:
Project no:
Author:
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.0 < 5.0% OK
Bolts 70.4 < 100% OK
Welds 77.4 < 100% OK
Buckling Not calculated
Plates
fy Thickness σEd εPl σcEd
Name Material Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Rafter-1-tfl 1 ST52 360.0 10.0 LE1 138.8 0.0 0.0 OK
Rafter-1-bfl 1 ST52 360.0 10.0 LE4 127.0 0.0 0.0 OK
Rafter-1-w 1 ST52 360.0 6.0 LE1 111.7 0.0 0.0 OK
Rafter-2-tfl 1 ST52 360.0 10.0 LE1 193.4 0.0 0.0 OK
Rafter-2-bfl 1 ST52 360.0 10.0 LE1 161.7 0.0 0.0 OK
Rafter-2-w 1 ST52 360.0 6.0 LE1 143.7 0.0 0.0 OK
Strut-1 ST37 240.0 4.0 LE1 128.5 0.0 0.0 OK
Strut-2 ST37 240.0 4.0 LE4 129.3 0.0 0.0 OK
Brace-1 ST37 240.0 4.0 LE1 44.6 0.0 0.0 OK
Brace-2 ST37 240.0 4.0 LE1 44.6 0.0 0.0 OK
SP1 ST52 360.0 20.0 LE1 126.9 0.0 17.9 OK
SP2 ST52 360.0 20.0 LE1 137.8 0.0 18.0 OK
RIB1 ST52 360.0 10.0 LE4 141.1 0.0 0.0 OK
RIB2 ST52 360.0 10.0 LE1 145.4 0.0 0.0 OK
RIB3 ST52 360.0 10.0 LE1 146.1 0.0 0.0 OK
RIB4 ST52 360.0 10.0 LE4 143.2 0.0 0.0 OK
CPL3 ST52 360.0 10.0 LE1 116.9 0.0 9.2 OK
CPL2 ST52 360.0 10.0 LE4 125.6 0.0 11.7 OK
SP3 ST52 360.0 10.0 LE1 41.5 0.0 1.6 OK
CPL4 ST52 360.0 10.0 LE1 15.7 0.0 1.6 OK
SP4 ST52 360.0 10.0 LE1 39.9 0.0 1.1 OK
CPL5 ST52 360.0 10.0 LE1 15.9 0.0 1.1 OK
Design data
fy εlim
Material
[MPa] [%]
ST52 360.0 5.0
ST37 240.0 5.0
5 / 11
Project:
Project no:
Author:
6 / 11
Project:
Project no:
Author:
7 / 11
Project:
Project no:
Author:
Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 M22 Grade8.8 - 1 LE1 67.7 3.5 243.1 59.4 5.1 - OK
B2 M22 Grade8.8 - 1 LE1 68.7 3.8 237.9 60.3 5.5 - OK
B3 M22 Grade8.8 - 1 LE1 75.3 3.4 274.6 66.0 5.0 - OK
B4 M22 Grade8.8 - 1 LE1 80.3 3.9 274.6 70.4 5.7 - OK
B5 M22 Grade8.8 - 1 LE1 2.9 3.4 274.6 2.6 4.9 - OK
B6 M22 Grade8.8 - 1 LE1 4.3 4.1 274.6 3.7 6.0 - OK
B7 M22 Grade8.8 - 1 LE1 0.0 2.7 238.9 0.0 4.0 - OK
B8 M22 Grade8.8 - 1 LE1 0.0 3.3 243.0 0.0 4.8 - OK
B9 M16 Grade 8.8 - 2 LE1 0.4 2.6 78.1 0.6 7.2 - OK
B10 M16 Grade 8.8 - 2 LE4 7.9 0.4 99.8 13.2 1.1 - OK
B11 M16 Grade 8.8 - 2 LE4 0.4 3.3 99.8 0.7 9.0 - OK
B12 M16 Grade 8.8 - 2 LE4 0.9 3.2 99.8 1.6 8.7 - OK
B13 M16 Grade 8.8 - 2 LE4 0.8 3.3 99.8 1.4 9.0 - OK
B14 M16 Grade 8.8 - 2 LE4 8.2 2.6 99.8 13.7 7.1 - OK
B15 M16 Grade 8.8 - 2 LE1 0.5 2.7 92.7 0.8 7.3 - OK
B16 M16 Grade 8.8 - 2 LE1 0.7 2.1 99.8 1.2 5.9 - OK
B17 M16 Grade 8.8 - 2 LE4 0.2 1.3 99.8 0.3 3.7 - OK
B18 M16 Grade 8.8 - 2 LE4 0.4 1.1 99.8 0.7 3.1 - OK
B19 M16 Grade 8.8 - 2 LE1 0.5 2.0 73.7 0.8 5.5 - OK
B20 M16 Grade 8.8 - 2 LE1 0.1 1.8 77.5 0.1 5.0 - OK
B21 M16 Grade 8.8 - 2 LE4 0.2 1.3 99.8 0.3 3.7 - OK
B22 M16 Grade 8.8 - 2 LE4 0.2 1.1 99.8 0.3 3.2 - OK
B23 M16 Grade 8.8 - 2 LE1 0.5 2.0 73.4 0.8 5.6 - OK
B24 M16 Grade 8.8 - 2 LE1 0.1 1.8 76.6 0.2 5.0 - OK
Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
M22 Grade8.8 - 1 114.0 68.4
M16 Grade 8.8 - 2 60.3 36.2
8 / 11
Project:
Project no:
Author:
Where:
Fnt = 600.0 MPa – nominal tensile stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Where:
Fnv = 360.0 MPa – nominal shear stress from AISC 360-16 Table J3.2
Ab = 380 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 274.6 kN ≥ V = 3.9 kN
Where:
lc = 76 mm – clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 20 mm – thickness of the plate
d = 22 mm – diameter of a bolt
Fu = 520.0 MPa – tensile strength of the connected material
Ω = 2.00 – safety factor for bearing at bolt holes
9 / 11
Project:
Project no:
Author:
Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
SP2 Rafter-1-tfl 1 E70xx ◢3.5◣ ◢5.0◣ 199 33 LE1 19.3 25.5 75.7 OK
E70xx ◢3.5◣ ◢5.0◣ 199 33 LE1 19.4 25.5 76.0 OK
SP2 Rafter-1-bfl 1 E70xx ◢3.5◣ ◢5.0◣ 200 33 LE4 18.7 24.9 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 200 33 LE4 18.9 25.1 75.1 OK
SP2 Rafter-1-w 1 E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 17.0 25.6 66.4 OK
E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 17.4 25.6 67.7 OK
SP1 Rafter-2-tfl 1 E70xx ◢3.5◣ ◢5.0◣ 199 33 LE1 19.2 25.5 75.4 OK
E70xx ◢3.5◣ ◢5.0◣ 200 33 LE1 19.3 25.5 75.8 OK
SP1 Rafter-2-bfl 1 E70xx ◢3.5◣ ◢5.0◣ 200 33 LE4 18.8 25.0 75.1 OK
E70xx ◢3.5◣ ◢5.0◣ 200 33 LE4 19.0 25.2 75.1 OK
SP1 Rafter-2-w 1 E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 16.8 25.6 65.7 OK
E70xx ◢3.5◣ ◢5.0◣ 301 33 LE1 16.9 25.6 65.8 OK
SP2 RIB1 E70xx ◢3.5◣ ◢5.0◣ 95 10 LE4 3.6 7.2 49.4 OK
E70xx ◢3.5◣ ◢5.0◣ 95 10 LE4 3.5 7.2 48.7 OK
Rafter-1-bfl 1 RIB1 E70xx ◢3.5◣ ◢5.0◣ 150 10 LE4 5.3 6.9 76.9 OK
E70xx ◢3.5◣ ◢5.0◣ 150 10 LE4 5.3 6.8 76.8 OK
SP2 RIB2 E70xx ◢3.5◣ ◢5.0◣ 99 10 LE1 5.6 7.4 75.2 OK
E70xx ◢3.5◣ ◢5.0◣ 99 10 LE1 5.6 7.4 75.2 OK
Rafter-1-tfl 1 RIB2 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.2 6.8 77.3 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.2 6.7 77.3 OK
SP1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 99 10 LE4 4.9 6.5 75.2 OK
E70xx ◢3.5◣ ◢5.0◣ 99 10 LE4 4.9 6.5 75.1 OK
Rafter-2-tfl 1 RIB3 E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.2 6.7 77.2 OK
E70xx ◢3.5◣ ◢5.0◣ 149 10 LE1 5.2 6.7 77.4 OK
SP1 RIB4 E70xx ◢3.5◣ ◢5.0◣ 97 10 LE4 3.5 7.3 48.2 OK
E70xx ◢3.5◣ ◢5.0◣ 97 10 LE4 3.5 7.4 47.1 OK
Rafter-2-bfl 1 RIB4 E70xx ◢3.5◣ ◢5.0◣ 150 10 LE4 5.3 6.8 77.1 OK
E70xx ◢3.5◣ ◢5.0◣ 150 10 LE4 5.3 6.8 77.1 OK
CPL3 Strut-2-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.7 7.1 38.3 OK
CPL3 Strut-2-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.7 7.5 35.7 OK
CPL3 Strut-2-w 3 E70xx ◢3.5 ◢5.0 149 10 LE4 2.9 7.4 38.9 OK
CPL3 Strut-2-w 3 E70xx ◢3.5 ◢5.0 149 10 LE4 2.8 7.2 39.7 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.7 7.2 37.9 OK
CPL2 Strut-1-w 1 E70xx ◢3.5 ◢5.0 149 10 LE1 2.8 7.5 37.8 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE4 2.7 7.4 36.9 OK
CPL2 Strut-1-w 3 E70xx ◢3.5 ◢5.0 149 10 LE4 2.8 7.1 39.9 OK
Rafter-1-w 1 SP3 E70xx ◢3.5◣ ◢5.0◣ 219 15 LE1 2.3 9.5 24.3 OK
E70xx ◢3.5◣ ◢5.0◣ 219 15 LE1 1.8 7.7 23.5 OK
SP2 SP3 E70xx ◢4.0◣ ◢5.7◣ 96 14 LE1 1.8 8.2 22.2 OK
10 / 11
Project:
Project no:
Author:
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
E70xx ◢4.0◣ ◢5.7◣ 96 14 LE1 2.1 8.1 25.5 OK
CPL4 Brace-1-w 2 E70xx ◢3.5 ◢5.0 149 10 LE4 0.5 5.6 9.6 OK
CPL4 Brace-1-w 2 E70xx ◢3.5 ◢5.0 149 10 LE4 0.6 5.6 9.9 OK
CPL4 Brace-1-w 4 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.5 13.4 OK
CPL4 Brace-1-w 4 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.5 13.1 OK
Rafter-2-w 1 SP4 E70xx ◢4.0◣ ◢5.7◣ 239 15 LE1 2.8 9.3 29.7 OK
E70xx ◢4.0◣ ◢5.7◣ 239 15 LE1 2.1 8.8 23.6 OK
SP1 SP4 E70xx ◢4.0◣ ◢5.7◣ 226 15 LE1 1.8 8.9 20.1 OK
E70xx ◢4.0◣ ◢5.7◣ 226 15 LE1 2.2 8.7 24.9 OK
CPL5 Brace-2-w 2 E70xx ◢3.5 ◢5.0 149 10 LE4 0.5 5.6 9.6 OK
CPL5 Brace-2-w 2 E70xx ◢3.5 ◢5.0 149 10 LE4 0.6 5.6 9.9 OK
CPL5 Brace-2-w 4 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.5 13.4 OK
CPL5 Brace-2-w 4 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.5 13.0 OK
Where:
Fnw = 381.8 MPa – nominal stress of weld material:
Buckling
Buckling analysis was not calculated.
11 / 11
Project:
Project no:
Author:
Design
Name 10th of ramadan complex-512-VSL-Storage shed
Description T.DET.09
Analysis Stress, strain/ loads in equilibrium
Design code AISC - ASD 2016
1/8
Project:
Project no:
Author:
2/8
Project:
Project no:
Author:
Cross-sections
Name Material
5 - RHS125x125 ST37
Cross-sections
Name Material Drawing
5 - RHS125x125 ST37
Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
M16 Grade 8.8 M16 Grade 8.8 16 800.0 201
3/8
Project:
Project no:
Author:
Check
Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.0 < 5.0% OK
Bolts 4.9 < 100% OK
Welds 21.8 < 100% OK
Buckling Not calculated
GMNA Calculated
Plates
fy Thickness σEd εPl σcEd
Name Material Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
Brace-1 ST37 240.0 4.0 LE1 139.5 0.0 0.0 OK
Brace-2 ST37 240.0 4.0 LE1 44.4 0.0 0.0 OK
Brace-3 ST37 240.0 4.0 LE1 44.4 0.0 0.0 OK
SP1 ST37 240.0 10.0 LE1 20.3 0.0 1.2 OK
SP2 ST37 240.0 10.0 LE1 20.3 0.0 1.2 OK
CPL1 ST52 360.0 10.0 LE1 14.4 0.0 1.2 OK
CPL2 ST52 360.0 10.0 LE1 14.4 0.0 1.2 OK
Design data
fy εlim
Material
[MPa] [%]
ST37 240.0 5.0
ST52 360.0 5.0
4/8
Project:
Project no:
Author:
5/8
Project:
Project no:
Author:
Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 M16 Grade 8.8 - 1 LE1 0.6 1.8 69.1 1.0 4.9 - OK
Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
M16 Grade 8.8 - 1 60.3 36.2
6/8
Project:
Project no:
Author:
Where:
Fnt = 600.0 MPa – nominal tensile stress from AISC 360-16 Table J3.2
Ab = 201 mm2 – gross bolt cross-sectional area
Ω = 2.00 – safety factor for tension and shear
Where:
Fnv = 360.0 MPa – nominal shear stress from AISC 360-16 Table J3.2
Ab = 201 mm2 – gross bolt cross-sectional area
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 69.1 kN ≥ V = 1.8 kN
Where:
lc = 85 mm – clear distance, in the direction of the force, between the edge of the hole and the edge of the
adjacent hole or edge of the material
t = 10 mm – thickness of the plate
d = 16 mm – diameter of a bolt
Fu = 360.0 MPa – tensile strength of the connected material
Ω = 2.00 – safety factor for bearing at bolt holes
7/8
Project:
Project no:
Author:
Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
Brace-1-w 4 SP1 E70xx ◢3.5◣ ◢5.0◣ 259 10 LE1 1.3 6.1 21.8 OK
E70xx ◢3.5◣ ◢5.0◣ 259 10 LE1 0.9 5.5 16.2 OK
Brace-1-w 2 SP2 E70xx ◢3.5◣ ◢5.0◣ 259 10 LE1 1.3 6.1 21.8 OK
E70xx ◢3.5◣ ◢5.0◣ 259 10 LE1 0.9 5.5 16.2 OK
CPL1 Brace-2-w 2 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.5 12.5 OK
CPL1 Brace-2-w 2 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.5 12.8 OK
CPL1 Brace-2-w 4 E70xx ◢3.5 ◢5.0 149 10 LE4 0.5 5.6 9.3 OK
CPL1 Brace-2-w 4 E70xx ◢3.5 ◢5.0 149 10 LE4 0.5 5.7 9.0 OK
CPL2 Brace-3-w 2 E70xx ◢3.5 ◢5.0 149 10 LE4 0.5 5.7 9.0 OK
CPL2 Brace-3-w 2 E70xx ◢3.5 ◢5.0 149 10 LE4 0.5 5.6 9.2 OK
CPL2 Brace-3-w 4 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.5 12.8 OK
CPL2 Brace-3-w 4 E70xx ◢3.5 ◢5.0 149 10 LE1 0.7 5.5 12.5 OK
Where:
Fnw = 348.3 MPa – nominal stress of weld material:
Buckling
Buckling analysis was not calculated.
8/8
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 04/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
PGESCo Confidential
© Copyright 2023. All rights reserved
CFS Version 6.0.2 Page 1
Section: Section 1.sct nora
Zee 250x60x20x2.5 PGESCO
Section Inputs
CFS Version 6.0.2 Page 2
Section: Section 1.sct nora
Zee 250x60x20x2.5 PGESCO
¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯
Material: [S355]
No strength increase from cold work of forming.
Modulus of Elasticity, E 200000 MPa
Yield Strength, Fy 355 MPa
Tensile Strength, Fu 510 MPa
Warping Constant Override, Cw 0 mm^6
Torsion Constant Override, J 0 mm^4
Analysis Inputs
¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯
Members
Section File Revision Date and Time
1 Section 1.sct 07/10/2023 5:23:12 PM
2 Section 1.sct 07/10/2023 5:23:12 PM
3 Section 1.sct 07/10/2023 5:23:12 PM
4 Section 1.sct 07/10/2023 5:23:12 PM
5 Section 1.sct 07/10/2023 5:23:12 PM
6 Section 1.sct 07/10/2023 5:23:12 PM
7 Section 1.sct 07/10/2023 5:23:12 PM
Supports
Type Location Bearing Fastened K
(m) (mm)
1 XYT 0.000 60.0 No 1.0000
2 XT 2.500 25.4 No 1.0000
3 XT 5.000 25.4 No 1.0000
4 XYT 7.500 60.0 No 1.0000
5 XT 9.833 25.4 No 1.0000
6 XT 12.167 25.4 No 1.0000
7 XYT 14.500 60.0 No 1.0000
8 XT 16.833 25.4 No 1.0000
9 XT 19.167 25.4 No 1.0000
10 XYT 21.500 60.0 No 1.0000
11 XT 23.833 25.4 No 1.0000
12 XT 26.167 25.4 No 1.0000
13 XYT 28.500 60.0 No 1.0000
14 XT 30.833 25.4 No 1.0000
15 XT 33.167 25.4 No 1.0000
16 XYT 35.500 60.0 No 1.0000
17 XT 37.833 25.4 No 1.0000
18 XT 40.167 25.4 No 1.0000
19 XYT 42.500 60.0 No 1.0000
20 XT 45.000 25.4 No 1.0000
21 XT 47.500 25.4 No 1.0000
22 XYT 50.000 60.0 No 1.0000
Load Combination: D
Specification: 2007 North American Specification - US (ASD)
Inflection Point Bracing: Yes
Loading Factor
1 Beam Self Weight 1.0000
2 Dead Load 1.0000
Loads: P Mx Vy My Vx
(kN) (kN-m) (kN) (kN-m) (kN)
Total 0.000 4.448 0.432 -0.067 0.133
Applied 0.000 4.448 0.432 -0.067 0.133
Strength 46.356 11.519 40.113 1.885 32.877
Interaction Equations
NAS Eq. C5.2.1-1 (P, Mx, My) 0.000 + 0.386 + 0.035 = 0.421 <= 1.0
NAS Eq. C5.2.1-2 (P, Mx, My) 0.000 + 0.386 + 0.035 = 0.421 <= 1.0
NAS Eq. C3.3.1-1 (Mx, Vy) Sqrt(0.096 + 0.000)= 0.310 <= 1.0
NAS Eq. C3.3.1-1 (My, Vx) Sqrt(0.001 + 0.000)= 0.031 <= 1.0
Ae=829.83 mm^2
Pn=83.44 kN NAS C4.1-1
c=1.8, c=0.85
CFS Version 6.0.2 Page 5
Analysis: Analysis 1.anl nora
7-Span Beams with Laps PGESCO
VSL Storage shed (512)
Rev. Date: 07/10/2023 5:25:56 PM
By: nora
Ae=658.68 mm^2
CFS Version 6.0.2 Page 6
Analysis: Analysis 1.anl nora
7-Span Beams with Laps PGESCO
VSL Storage shed (512)
Rev. Date: 07/10/2023 5:25:56 PM
By: nora
Reaction
(kN)
3.1259 3.1259
7.1476 7.1476
7.7596 7.7596
9.2252 9.2252
5.0088
4.2164 3.9349
3.7146 3.8247
3.433
3.1259
Shear
(kN)
-3.1259
-3.433
-3.9349 -3.8247 -3.7146
-4.2164
-5.0088
4.5342 4.5342
2.101 2.101
1.7098
1.1812 1.1813
Moment
(kN-m)
-4.1375 -4.1375
-4.9086 -4.9086
-6.8793 -6.8793
1.2018 1.2018
Deflection 0.21126 0.21127
-12.075 -12.075
CFS Version 6.0.2
Analysis: Analysis 1.anl nora
7-Span Beams with Laps PGESCO
VSL Storage shed (512)
Rev. Date: 07/10/2023 5:25:56 PM
By: nora
Reaction
(kN)
0.098526 0.098526
0.2368 0.22496
0.22997 0.22892
0.22904 0.22894
0.22894 0.22892
0.22904 0.22496
0.22997 0.2368
0.25532 0.24255 0.24286 0.24286 0.24255 0.25532
0.28478 0.28478
0.15174
0.13303 0.13069
0.124620.116
0.11957 0.12135
0.11681 0.12143
0.11679 0.12143
0.11677 0.1212
0.11758 0.11723
0.11239 0.11215 0.11215 0.11223 0.10896
0.098526
Shear
(kN)
-0.098526
-0.11723 -0.10896 -0.11223
-0.11677 -0.11215
-0.11679 -0.11215
-0.11681 -0.11239
-0.116
-0.11758
-0.1212 -0.12143 -0.12143 -0.12135 -0.11957
-0.12462
-0.13069 -0.13304
-0.15174
0.048485 0.048485
0.024647
0.02188 0.02481 0.024269 0.024282 0.024269 0.02481 0.024647
0.02188
0.01903
0.016901 0.018842 0.018983
0.018978 0.018978
0.018983 0.01903
0.018842 0.016901
Moment
(kN-m)
-0.042399
-0.044243 -0.043881
-0.043837 -0.043846
-0.043846 -0.043837 -0.042399
-0.043881 -0.044243
-0.046763 -0.046763
-0.054523 -0.054669 -0.054669 -0.054523
-0.060668 -0.060667
-0.066518 -0.066518
(mm)
-0.030435 -0.038284
-0.039093 -0.038904
-0.038885 -0.038885 -0.038284 -0.030435 -0.045737
-0.038904 -0.039093
-0.045736
-0.065577 -0.061908 -0.059429 -0.059489 -0.059429 -0.061908 -0.065576
-0.17211 -0.17211
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 04/10/2023
BY : Nora Mostafa REV. NO 0
Page NO.
PGESCo Confidential
© Copyright 2023. All rights reserved
- Principal Wind pressure q = 0.5 * 10-3 * ρ * V2 * ct * cs
q = 0.5 * 10-3 * 1.25 * 332 * 1 * 1 = 0.68 kN/m2 = 68 kg/m2
Wx & W-x
Whole Structure
Dimensions
PGESCo Confidential
© Copyright 2023. All rights reserved
CALCULATION SHEET
PROJECT 10th Ramadan Complex
JOB NO. 10171A
CALC. NO. 09-SSC-0512-00001
SUBJECT : VSL Storage Shed (512) DATE 04/10/2023
BY : Nora Mostafa REV. NO 0
Attachment ( A )
PGESCo Confidential
© Copyright 2023. All rights reserved
Job No Sheet No Rev
10171A 1 00
Job Information
Engineer Checked Approved
Project ID
Project Name
Primary 1 D
Primary 2 L
Primary 3 W(+X)00CASE1
Primary 4 W(-X)00CASE1
Primary 5 W(-Z)00CASE1
Primary 6 W(+Z)00CASE1
Primary 7 W(+X)00CASE2
Primary 8 W(-X)00CASE2
Primary 9 W(-Z)00CASE2
Primary 10 W(+Z)00CASE2
Primary 11 W(+X)00CASE3
Primary 12 W(-X)00CASE3
Primary 13 W(-Z)00CASE3
Primary 14 W(+Z)00CASE3
Primary 15 W(+X)00CASE4
Primary 16 W(-X)00CASE4
Primary 17 W(-Z)00CASE4
Primary 18 W(+Z)00CASE4
Primary 19 W(+X)00CASE5
Primary 20 W(-X)00CASE5
Primary 21 W(-Z)00CASE5
Primary 22 W(+Z)00CASE5
Primary 23 W(+X)00CASE6
Primary 24 W(-X)00CASE6
Primary 25 W(-Z)00CASE6
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 1 of 36
Job No Sheet No Rev
10171A 2 00
Primary 26 W(+Z)00CASE6
Primary 27 T(+X)
Primary 28 T(-X)
Primary 100 GENERATED ECP ASD 1
Primary 101 GENERATED ECP ASD 2
Primary 102 GENERATED ECP ASD 3
Primary 103 GENERATED ECP ASD 4
Primary 104 GENERATED ECP ASD 5
Primary 105 GENERATED ECP ASD 6
Primary 106 GENERATED ECP ASD 7
Primary 107 GENERATED ECP ASD 8
Primary 108 GENERATED ECP ASD 9
Primary 109 GENERATED ECP ASD 10
Primary 110 GENERATED ECP ASD 11
Primary 111 GENERATED ECP ASD 12
Primary 112 GENERATED ECP ASD 13
Primary 113 GENERATED ECP ASD 14
Primary 114 GENERATED ECP ASD 15
Primary 115 GENERATED ECP ASD 16
Primary 116 GENERATED ECP ASD 17
Primary 117 GENERATED ECP ASD 18
Primary 118 GENERATED ECP ASD 19
Primary 119 GENERATED ECP ASD 20
Primary 120 GENERATED ECP ASD 21
Primary 121 GENERATED ECP ASD 22
Primary 122 GENERATED ECP ASD 23
Primary 123 GENERATED ECP ASD 24
Primary 124 GENERATED ECP ASD 25
Primary 125 GENERATED ECP ASD 26
Primary 126 GENERATED ECP ASD 27
Primary 127 GENERATED ECP ASD 28
Primary 128 GENERATED ECP ASD 29
Primary 129 GENERATED ECP ASD 30
Primary 130 GENERATED ECP ASD 31
Primary 131 GENERATED ECP ASD 32
Primary 132 GENERATED ECP ASD 33
Primary 133 GENERATED ECP ASD 34
Primary 134 GENERATED ECP ASD 35
Primary 135 GENERATED ECP ASD 36
Primary 136 GENERATED ECP ASD 37
Primary 137 GENERATED ECP ASD 38
Primary 138 GENERATED ECP ASD 39
Primary 139 GENERATED ECP ASD 40
Primary 140 GENERATED ECP ASD 41
Primary 141 GENERATED ECP ASD 42
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 2 of 36
Job No Sheet No Rev
10171A 3 00
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 3 of 36
Job No Sheet No Rev
10171A 4 00
Y
X
Z Load 1 (SELF Y)
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 4 of 36
Job No Sheet No Rev
10171A 5 00
Y
X
Z Load 2
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 5 of 36
Job No Sheet No Rev
10171A 6 00
Y
X
Z Load 3
W(+X)00CASE1
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 6 of 36
Job No Sheet No Rev
10171A 7 00
Y
X
Z Load 4
W(-X)00CASE1
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 7 of 36
Job No Sheet No Rev
10171A 8 00
Y
X
Z Load 5
W(-Z)00CASE1
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 8 of 36
Job No Sheet No Rev
10171A 9 00
Y
X
Z Load 6
W(+Z)00CASE1
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 9 of 36
Job No Sheet No Rev
10171A 10 00
Y
X
Z Load 7
W(+X)00CASE2
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 10 of 36
Job No Sheet No Rev
10171A 11 00
Y
X
Z Load 8
W(-X)00CASE2
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 11 of 36
Job No Sheet No Rev
10171A 12 00
Y
X
Z Load 9
W(-Z)00CASE2
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 12 of 36
Job No Sheet No Rev
10171A 13 00
Y
X
Z Load 10
W(+Z)00CASE2
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 13 of 36
Job No Sheet No Rev
10171A 14 00
Y
X
Z Load 11
W(+X)00CASE3
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 14 of 36
Job No Sheet No Rev
10171A 15 00
Y
X
Z Load 12
W(-X)00CASE3
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 15 of 36
Job No Sheet No Rev
10171A 16 00
Y
X
Z Load 13
W(-Z)00CASE3
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 16 of 36
Job No Sheet No Rev
10171A 17 00
Y
X
Z Load 14
W(+Z)00CASE3
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 17 of 36
Job No Sheet No Rev
10171A 18 00
Y
X
Z Load 15
W(+X)00CASE4
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 18 of 36
Job No Sheet No Rev
10171A 19 00
Y
X
Z Load 16
W(-X)00CASE4
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 19 of 36
Job No Sheet No Rev
10171A 20 00
Y
X
Z Load 17
W(-Z)00CASE4
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 20 of 36
Job No Sheet No Rev
10171A 21 00
Y
X
Z Load 18
W(+Z)00CASE4
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 21 of 36
Job No Sheet No Rev
10171A 22 00
Y
X
Z Load 19
W(+X)00CASE5
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 22 of 36
Job No Sheet No Rev
10171A 23 00
Y
X
Z Load 20
W(-X)00CASE5
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 23 of 36
Job No Sheet No Rev
10171A 24 00
Y
X
Z Load 21
W(-Z)00CASE5
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 24 of 36
Job No Sheet No Rev
10171A 25 00
Y
X
Z Load 22
W(+Z)00CASE5
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 25 of 36
Job No Sheet No Rev
10171A 26 00
Y
X
Z Load 23
W(+X)00CASE6
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 26 of 36
Job No Sheet No Rev
10171A 27 00
Y
X
Z Load 24
W(-X)00CASE6
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 27 of 36
Job No Sheet No Rev
10171A 28 00
Y
X
Z Load 25
W(-Z)00CASE6
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 28 of 36
Job No Sheet No Rev
10171A 29 00
Y
X
Z Load 26
W(+Z)00CASE6
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 29 of 36
Job No Sheet No Rev
10171A 30 00
Y
X
Z Load 27
T(+X)
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 30 of 36
Job No Sheet No Rev
10171A 31 00
Y
X
Z Load 28
T(-X)
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 31 of 36
Job No Sheet No Rev
10171A 32 00
Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
Max FX 21 107:GENERATE 27.853 86.055 -2.306 0 0 0
Min FX 25 106:GENERATE -27.853 86.055 -2.306 0 0 0
Max FY 30 108:GENERATE 24.000 94.638 9.669 0 0 0
Min FY 25 5:W(-Z)00CASE1 11.694 -51.243 10.994 0 0 0
Max FZ 134 231:GENERATE -18.144 81.977 11.533 0 0 0
Min FZ 107 232:GENERATE -18.090 79.661 -10.515 0 0 0
Max MX 1 1:D -0.270 22.533 -0.004 0 0 0
Min MX 1 1:D -0.270 22.533 -0.004 0 0 0
Max MY 1 1:D -0.270 22.533 -0.004 0 0 0
Min MY 1 1:D -0.270 22.533 -0.004 0 0 0
Max MZ 1 1:D -0.270 22.533 -0.004 0 0 0
Min MZ 1 1:D -0.270 22.533 -0.004 0 0 0
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 32 of 36
Job No Sheet No Rev
10171A 33 00
Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 Taper Taper 0.110 1.000 0.110 Eq. H1-1b 106 83.700 29.8E+3 3.13E+3 31.644
2 Taper Taper 0.648 1.000 0.648 Eq. H1-1a 107 64.000 21.6E+3 1.33E+3 16.213
3 Taper Taper 0.328 1.000 0.328 Sec. G1 108 89.700 44.6E+3 3.13E+3 32.364
4 Taper Taper 0.498 1.000 0.498 Eq. H1-1a 108 58.000 11E+3 1.33E+3 15.493
10 Taper Taper 0.097 1.000 0.097 Eq. H1-1b 108 83.700 29.8E+3 3.13E+3 31.644
12 Taper Taper 0.327 1.000 0.327 Sec. G1 109 89.700 44.6E+3 3.13E+3 32.364
18 SEC7 SEC7 0.177 1.000 0.177 Eq. H1-1b 109 123.840 18.9E+3 19.1E+3 57.805
20 SEC1 SEC1 0.929 1.000 0.929 Eq. H1-1b 109 134.160 19.5E+3 44.5E+3 49.408
26 SEC7 SEC7 0.182 1.000 0.182 Eq. H1-1b 108 123.840 18.9E+3 19.1E+3 57.805
28 SEC1 SEC1 0.961 1.000 0.961 Eq. H1-1b 108 134.160 19.5E+3 44.5E+3 49.408
82 SQU 0.1X0. SQU 0.1X0. 0.231 1.000 0.231 Eq. H1-1b 101 19.360 472.932 472.932 708.625
90 SQU 0.1X0. SQU 0.1X0. 0.231 1.000 0.231 Eq. H1-1b 101 19.360 472.932 472.932 708.625
91 SQU 0.1X0. SQU 0.1X0. 0.231 1.000 0.231 Eq. H1-1b 101 19.360 472.932 472.932 708.625
99 SQU 0.1X0. SQU 0.1X0. 0.231 1.000 0.231 Eq. H1-1b 101 19.360 472.932 472.932 708.625
154 SEC7 SEC7 0.172 1.000 0.172 Eq. H1-1b 109 123.840 18.9E+3 19.1E+3 57.805
156 SEC1 SEC1 0.906 1.000 0.906 Eq. H1-1b 109 134.160 19.5E+3 44.5E+3 49.408
162 Taper Taper 0.842 1.000 0.842 Eq. H1-1b 107 84.000 30.8E+3 3.13E+3 31.680
164 Taper Taper 0.842 1.000 0.842 Eq. H1-1b 106 84.000 30.8E+3 3.13E+3 31.680
170 Taper Taper 0.842 1.000 0.842 Eq. H1-1b 107 84.000 30.8E+3 3.13E+3 31.680
172 Taper Taper 0.842 1.000 0.842 Eq. H1-1b 106 84.000 30.8E+3 3.13E+3 31.680
178 SEC7 SEC7 0.177 1.000 0.177 Eq. H1-1b 108 123.840 18.9E+3 19.1E+3 57.805
180 SEC1 SEC1 0.937 1.000 0.937 Eq. H1-1b 108 134.160 19.5E+3 44.5E+3 49.408
186 Taper Taper 0.819 1.000 0.819 Eq. H1-1b 108 58.000 11E+3 1.33E+3 15.493
187 SQU 0.1X0. SQU 0.1X0. 0.206 1.000 0.206 Eq. H1-1b 101 19.360 472.932 472.932 708.625
188 SQU 0.1X0. SQU 0.1X0. 0.206 1.000 0.206 Eq. H1-1b 101 19.360 472.932 472.932 708.625
189 SQU 0.1X0. SQU 0.1X0. 0.206 1.000 0.206 Eq. H1-1b 101 19.360 472.932 472.932 708.625
190 Taper Taper 0.820 1.000 0.820 Eq. H1-1b 108 58.000 11E+3 1.33E+3 15.493
191 Taper Taper 0.819 1.000 0.819 Eq. H1-1b 108 58.000 11E+3 1.33E+3 15.493
192 SQU 0.1X0. SQU 0.1X0. 0.206 1.000 0.206 Eq. H1-1b 101 19.360 472.932 472.932 708.625
193 SQU 0.1X0. SQU 0.1X0. 0.206 1.000 0.206 Eq. H1-1b 101 19.360 472.932 472.932 708.625
194 SQU 0.1X0. SQU 0.1X0. 0.206 1.000 0.206 Eq. H1-1b 101 19.360 472.932 472.932 708.625
195 Taper Taper 0.820 1.000 0.820 Eq. H1-1b 108 58.000 11E+3 1.33E+3 15.493
300 SQU 0.1X0. SQU 0.1X0. 0.086 1.000 0.086 Sec. E1 109 19.360 472.932 472.932 708.625
301 SQU 0.1X0. SQU 0.1X0. 0.086 1.000 0.086 Sec. E1 109 19.360 472.932 472.932 708.625
302 SQU 0.1X0. SQU 0.1X0. 0.054 1.000 0.054 Sec. E1 108 19.360 472.932 472.932 708.625
303 SQU 0.1X0. SQU 0.1X0. 0.054 1.000 0.054 Sec. E1 108 19.360 472.932 472.932 708.625
312 SQU 0.1X0. SQU 0.1X0. 0.049 1.000 0.049 Sec. E1 109 19.360 472.932 472.932 708.625
313 SQU 0.1X0. SQU 0.1X0. 0.049 1.000 0.049 Sec. E1 109 19.360 472.932 472.932 708.625
314 SQU 0.1X0. SQU 0.1X0. 0.096 1.000 0.096 Sec. E1 108 19.360 472.932 472.932 708.625
315 SQU 0.1X0. SQU 0.1X0. 0.096 1.000 0.096 Sec. E1 108 19.360 472.932 472.932 708.625
316 SQU 0.2X0. SQU 0.2X0. 0.351 1.000 0.351 Eq. H1-1b 127 26.190 924.966 924.966 1.39E+3
317 SQU 0.1X0. SQU 0.1X0. 0.088 1.000 0.088 Eq. H1-1b 128 19.360 472.932 472.932 708.625
318 SQU 0.1X0. SQU 0.1X0. 0.080 1.000 0.080 Eq. H1-1b 101 19.360 472.932 472.932 708.625
319 SQU 0.1X0. SQU 0.1X0. 0.080 1.000 0.080 Eq. H1-1b 101 19.360 472.932 472.932 708.625
320 SQU 0.1X0. SQU 0.1X0. 0.080 1.000 0.080 Eq. H1-1b 101 19.360 472.932 472.932 708.625
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 33 of 36
Job No Sheet No Rev
10171A 34 00
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 34 of 36
Job No Sheet No Rev
10171A 35 00
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 35 of 36
Job No Sheet No Rev
10171A 36 00
Print Time/Date: 07/10/2023 18:09 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 36 of 36