Professional Documents
Culture Documents
Air Outlets Accessories Compliance Sheets
Air Outlets Accessories Compliance Sheets
1
B Coordination Drawings: Reflected ceiling plans and wall
elevations drawn to scale to show locations and coordination of
diffusers, registers, and grilles with other items installed in contractor sope
ceilings and walls.
2
F Tie Rods: Galvanized steel, 6-mm minimum diameter for 900-
mm length or less; 10-mm minimum diameter for lengths longer Out of scope
than 900 mm.
2.2 BAGKD - AND PRESSURE RELIEF DAMPERS
A Description :Gravity balanced, suitable for horizontal or vertical
installations .Dampers shall not produce noise while in operation comply
3
A General: Factory fabricated with required hardware and
accessories. Stiffen damper blades for stability. Include locking
device to hold single-blade dampers in a fixed positionwithout comply
vibration. Close duct penetrations for damper components to
seal duct consistent with pressure class.
1- Pressure Classifications of 500 Pa (2-Inch wg) or Higher: End
bearings or other seals
for ducts with axles full length of damper blades and bearings at comply
both ends of
operating shaft
B Low-Leakage Volume Dampers: Multiple- or single-blade,
parallel- or opposed-blade design as indicated, low-leakage
comply
rating, with linkage outside airstream, and suitable for horizontal
or vertical applications.
1 Steel Frames: Hat-shaped, galvanized, sheet steel channels,
minimum of 1.6 mm thick, with mitered and welded comers;
frames with flanges where indicated for attaching to walls; and comply
flangeless frames where indicated for installing in ducts.
2 Aluminum Frames: Hat-shaped, 1.6-mm thick, extruded-
aluminum channels; frames with flanges where indicated for
comply
attaching to walls; and flangeless frames whereindicated for
installing in ducts.
4
3 Roll-Formed Steel Blades: 1.6-mm thick, galvanized, sheet steel. N/A
4 Roll-Formed Aluminum Blades: 2.5-mm thick aluminum sheet.
N/A
5 Extruded-Aluminum Blades: 1.2-mm thick extruded aluminum.
Comply
6 Blade Axles: Nonferrous. Comply
7 Blade Axles: Galvanized steel Comply
8 Tie Bars and Brackets: Aluminum. N/A
9 Tie Bars and Brackets: Galvanized steel. Comply
C Jackshaft: 25-mm diameter, galvanized steel pipe rotating within
a pipe-bearing assembly mounted on supports at each mullion
Comply as noted Square = 12.5x12.5
and at each end of multiple-damper assemblies..
4 FIRE DAMPERS
a General: Labeled to UL 555. comply
b Fire Rating: One and one-half hours. comply
c Fire Rating: One and one-half and three hours comply
d Frame: SMACNA Type A with blades in airstream; fabricated with roll-
formed, 0.85-mm thick galvanized steel; with mitered and interlocking comply
comers.
e Frame: SMACNA Type B with blades out of airstream; fabricated with
roll-fonned, 0.85-mm thick galvanized steel; with mitered and comply
interlocking comers.
f Mounting Sleeve: Factory- or field-installed galvanized, sheet steel.
comply
1 Minimum Thickness: 1.3 mm or 3.5 mm thick as indicated, and length
to suit comply
application
2 Exceptions: Omit sleeve where damper frame width pennits
direct attachment of perimeter mounting angles on each side of
comply
wall or floor, and thickness of damper frame complies with
sleeve requirements.
5
G Mounting Orientation: Vertical or horizontal as indicated. comply
H Blades: Roll-formed, interlocking, 0.85-mm thick, galvanized,
sheet steel. In place of interlocking blades, use full-length, 0.85-
comply
mm thick, galvanized steel blade connectors..
6
8 Modulating, Spring-Return Motor: 230 V, single phase, 50 Hz.
N/A
9 Modulating, Spring-Return Motor: 380 V, 3 phase, 50 Hz. N/A
G Accessories:
1 Auxiliary switches for signaling or position indication. comply
2 Test and reset switches, damper or remote mounted as
N/A
practical.
2.6 COMBINATION FIRE AND SMOKE DAMPERS
A Type: Dynamic; rated and labeled according to UL 555 and UL
comply
555S.
B Fire Rating: 1-1/2 and 3 hours. comply
C Frame: Hat-shaped, 0.094-inch- (2.4-mm-) thick, galvanized
sheet steel, with welded comers and mounting flange.
7
3 Spring-Return Motors: Equip with an integral spiral-spring
mechanism where indicated. Enclose entire spring mechanism in
a removable housing designed for service or adjustments. Size
for running torque rating of 150 in. x !bf (17 N x m) and comply
breakaway torque rating of 150 in. x !bf (I 7 N x m).
8
A Door shall be rigid and airtight with neoprene gaskets and two or
more chrome-plated enamel painted steel hinges and quick
fastening locking devices. Provide doors as large as practical.
Include vision panel where indicated. Include 25-by-25 mm butt comply
or piano hinge and cam latches. Access doors up to 300 X 300
mm shall have two cam locks, larger sizes shall have four cam
locks.
B Mount doors, if possible, so that air pressure holds them closed. As an
alternative, removable access doors may be used. N/A
C Access doors shall be constructed from stamped sheet metal and
consist of an inner and outer door panel. Where insulated doors are
needed, the inner door shall consist of two panels spot-welded
together which totally encapsulate insulation identical to comply
corresponded ductwork insulation. The inner and outer doors shall be
joined by bolts and threaded handles in such a configuration that the
panels can be drawn together to secure the door to the duct in a
D The handles shall be high impact plastic with threaded metal inserts.
Conical springs shall be used between the door panels to facilitate
installation and removal of the door. Fireproof neoprene gasket shall N/A
be used around the outside edge of the inner or outer panel, but not
both, to seal the door.
E This type of door is approved for use on rectangular, round and flat-
comply
oval ductwork.
F Insulation: 25-mm thick, fibrous-glass or polystyrene-foam board comply
9
10
11
12