Professional Documents
Culture Documents
Cdot Commands - R2
Cdot Commands - R2
Select appropriate card slot for the PCM cable to be terminated in the C-DOT switch.
Insert one DTS card & one DTC card (compatible to the new version of C-DOT) and
equip it with the help of following command.
<EQUIP-TRML-CARD
CARD-TYP : DTK-CAS (4)
CARD-SLT : Card slot taken for the PCM to be terminated (for e.g. 1-1-3-3)
VER : 1
. : default
. : default
<REPEAT/EXECUTE/TERMINATE: E
If required, un-equip it and equip it again. To un-equip the card, use the following
command.
<UNEQ-TRML-CARD
CARD-SLT : Card slot to be unequipped should be given (for e.g. 1-1-3-3)
<REPEAT/EXECUTE/TERMINATE: E
TGP-TYP :
ORD (1)
[TGP-FCY] :
default
[DGT-SZFD] :
default
[RNG-DWN] :
default
[DIAL-TN] :
default
[TGP-CAT] :
A spare category to be given
[HNT-TYP] :
default
[CAMA] :
YES (1)
[SIG-INF] :
CLI-N-FAIL (7)
[CONT-CHK] :
default
[ECHO-SUP] :
default
[SAT-IND] :
default
AC-STA :
2WP (1)
[AC-INFO] :
default
[TEN] :
TENs to be provided (ports to be assigned) like 1-1-3-3-2to1-1-3-
3-16&1-1-3-3-18to1-1-3-3-27 (for card slot 1-1-3-3)
[TEN-NO7] : default
<REPEAT/EXECUTE/TERMINATE: R
Note: - By repeating above command, create the next trunk group for ILD calls handling. The
TEN will be like 1-1-3-3-28to1-1-3-3-32 for card slot 1-1-3-3.
<ADD-TGP-BLG
TGP-NUM : Created TGP number for ILD
[TGP-NAME] : default
<REPEAT/EXECUTE/TERMINATE: E
<DISPL-TGP
TGP-NUM : Created trunk group no. for ILD
[TGP-NAME] : default
<REPEAT/EXECUTE/TERMINATE: E
Now, check the circuit’s status with the help of following command.
<DISPL-TGP-STATUS
[STATUS-TRM] : default
TGP-NUM : Created trunk group number for NLD
TGP-NAME : default
<REPEAT/EXECUTE/TERMINATE: R
<DISPL-TGP-STATUS
[STATUS-TRM] : default
TGP-NUM : Created trunk group number for ILD
TGP-NAME : default
<REPEAT/EXECUTE/TERMINATE: E
Note: - The circuit status should be INS-FREE to make the call thru.
Again, above step is to be repeated for service type 1 to 3 i.e. BS1 to BS3.
<MOD-CHB-CRG
TYP : CRE-CHB (4)
CRG-BAND-NUM : 133
CRG-RTN : A no. which is created for 3.1 seconds
<REPEAT/EXECUTE/TERMINATE: E
<DISPL-SUB-CRG
CLG-CAT : 1
CLD-CAT : default
CRG-RTN : default
<REPEAT/EXECUTE/TERMINATE: E
Note down all the called categories from the output of above command and allow calls
from new categories given in the trunk groups created for this POI as below.
<MOD-SUB-CRG
CLG-CAT : NLD TGP CATEGORY
CLD-CAT : One from the categories noted earlier.
CRG-RTN : Charge rate number created for 20 sec
<REPEAT/EXECUTE/TERMINATE: R
<MOD-SUB-CRG
CLG-CAT : ILD TGP CATEGORY
CLD-CAT : One from the categories noted earlier.
CRG-RTN : Charge rate number created for 3.1 sec
<REPEAT/EXECUTE/TERMINATE: R
Get all route codes which begin with 2 and note down all the parameters given in these route
codes one by one with the help of following command.
<DISPL-ROUT-CHAR
RUT-COD : One route code from the list noted above
<REPEAT/EXECUTE/TERMINATE: R
*Newly created categories for NLD & ILD POI TGP should also be included.
**Newly created categories for NLD & ILD POI TGP should also be included with proper
charge rate number i.e. 20 sec & 3.1 sec for NLD & ILD cat respectively.
Note: - Repeat above command until all route codes are modified.
IC UNITS : default
OG UNITS : default
<EXECUTE/MODIFY/TERMINATE: E
If CDR is shown saying the reason “no records found” promptly as you give the input,
just check for the year field in the script file of tgcbr2_2 and change it as per requirement
as below.
IOP5X> cd
IOP5X> cd rgen
IOP5X> vi tgcbr2_2 - It will open the script file tgcbr2_2 in VI editor.
Go to the proper line in which the date is mentioned in the format “ddmm05” or
“ddmm06” by pressing key “j” (To bring cursor downwards press “j” key and “k” to
go upwards). Then take the cursor to the position of 5 or 6 by pressing key “l” (key “l”
to move the cursor right and “h” to move it left) and replace the character by pressing
“r7” (replace old value by 7 for year 2007 and “r8” for year 2008). Then, press
“:wq” and enter; it will save the file and quit. And run the above given command to get
CDR in the required format.
If CDR is not generated, just remove the trunk group from billing and add it again under
billing by the command REM-TGP-BLG & ADD-TGP-BLG. It will start recording the
CDR.