Professional Documents
Culture Documents
International Standard 11127-5
International Standard 11127-5
STANDARD 11127-5
First edition
1993-l 2-l 5
Reference number
IS0 11127-5:1993(E)
--`,,,`-`-`,,`,,`,`,,`---
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
IS0 11127 consists of the following parts, under the general title Prep-
aration of steel substrates before application of paints and related
products - Test methods for non-metallic blast-cleaning abrasives:
- Part I: Sampling
--`,,,`-`-`,,`,,`,`,,`---
- Part 2: Determination of particle size distribution
0 IS0 1993
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii
Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
0 IS0 IS0 11127-5:1993(E)
At the time of publication of this part of IS0 11127, part 8 was in course
of preparation.
--`,,,`-`-`,,`,,`,`,,`---
..
Ill
--`,,,`-`-`,,`,,`,`,,`---
Part 5:
Determination of moisture
This part of IS0 11127 specifies a method for the 3.2 Oven, capable of being maintained at a tem-
determination of the level of free moisture present in perature of (110 * 5) “C.
non-metallic blast-cleaning abrasives. It is determined
by measuring the mass lost on heating.
3.3 Balance, capable of weighing to an accuracy of
0,Ol g.
--`,,,`-`-`,,`,,`,`,,`---
5.1 Test portion m, is the mass, in grams, of the test portion af-
ter heating.
Dry the container (3.1) in the oven (3.2) at
(110 + 5)“C for 15 min and allow it to cool to room If the duplicate determinations differ by more than
temperature in the desiccator (3.4). Weigh the con- 0,05 % (absolute), repeat the procedure described in
tainer to the nearest 0,Ol g. Weigh into the container, clause 5.
to the nearest 0,Ol g, a test portion of approximately
Calculate the mean of two valid determinations and
100 9 (q). report the result to the nearest 0,Ol %.
5.2 Determination
7 Test report
Place the container with the test portion in the oven
The test report shall contain at least the following in-
(3.21, previously adjusted to (110 + 5)X, and leave
formation:
for at least 1 h. Transfer the container to the
desiccator and allow to cool to room temperature.
a) all details necessary to identify the product tested,
Reweigh the container with the dried test portion to
in accordance with the appropriate part of
the nearest 0,Ol g and determine the mass of the
IS0 11126 (see annex A), if applicable;
dried test portion (m,).
b) a reference to this part of IS0 11127
6 Expression of results (IS0 11127-5);
--`,,,`-`-`,,`,,`,`,,`---
Annex A
(informative)
Requirements and test methods for non-metallic IS0 11127 will consist of the following parts, under
blast-cleaning abrasives are contained in IS0 11126 the general title:
and IS0 11127 respectively.
Preparation of s tee/ substrates before application
IS0 11126 will consist of the following parts under of paints and related products - Test methods for
the general title: non-metallic blast-cleaning abrasives
--`,,,`-`-`,,`,,`,`,,`---
UDC 667.648.1:621.7.023:621.921.2/.3:543.712
Descriptors: paints, varnishes, substrates, steel products, blast-cleaning, abrasives, non-metallic abrasives, tests, determination of
content, humidity, gravimetric analysis.
Price based on 3 pages