Professional Documents
Culture Documents
CSWP Book - Segment2 - Samples
CSWP Book - Segment2 - Samples
CSWP Book - Segment2 - Samples
Segment 2 Configurations
Analyzing configuration
Modifying configuration
Understanding design intent
Modifying geometry
Creating feature
Start Examination>
274 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Examination Information
Welcome to the CSWP Segment 2 Core Exam (CSWPCORE)
As per the Candidate Conduct Policy you have agreed to, all models you submit in response
to the questions in this SOLIDWORKS Certification exam will be your original work, and you
did not reuse any models from a social website or other website. Also, all answers you submit
in the SOLIDWORKS Certification exam are you own and you will not obtain any answer
from a third party source.
Start Examination>
275 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 1 of 12
For 5 points
This test describes the problem set that must be solved in this problem set. Please
read this in its entirety before proceeding and click Yes for 5 points.
Please note that the use of other test taker’s completed models and assemblies can
lead to the annulment of your results per the Candidate Conduct Policy you agreed
to.
You will create a part using the drawings and parameters specified in the following
questions.
Note: The images shown may not be to proportion depending on the parameters you
are given. They are meant as a reference only for the dimensions and parameters
used to create the part.
Yes
Next question ≫
276 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 2 of 12
For 9 points
Change angle
X = 40 degree
Y = 3 mm
Next question ≫
277 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Part A
Part B
278 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 3 of 12
For 9 points
Modification Cutout
-Modify the part from the last question by adding removing or modifying the minimum
amount of dimensions or features. Sketch and feature dimensions should be kept
unless directed.
Enter values
(Use . (Point) as decimal separation)
Next question ≫
279 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Part A
Part B
280 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 4 of 12
For 9 points
-Modify the part from the last question by adding removing or modifying the minimum
amount of dimensions or features. Sketch and feature dimensions should be kept
unless directed.
-Reduce the shell thickness of the both side from 2mm to 1mm
Note: If you rebuild after adjusting the shell thickness, an error may occur. Find and
fix the error.
Enter values
(Use . (Point) as decimal separation)
Next question ≫
281 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Part A
Part B
282 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 5 of 12
For 9 points
-Modify the part from the last question by adding removing or modifying the
minimum amount of dimensions or features. Sketch and feature dimensions should
be kept unless directed.
Enter values
(Use . (Point) as decimal separation)
Next question ≫
283 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Part A
Part B
284 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 6 of 12
For 9 points
-Modify the part from the last question by adding removing or modifying the minimum
amount of dimensions or features. Sketch and feature dimensions should be kept
unless directed.
Enter values
(Use . (Point) as decimal separation)
Next question ≫
285 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Part A
Part B
286 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 7 of 12
For 9 points
Add grooves
-Modify the part from the last question by adding removing or modifying the minimum
amount of dimensions or features. Sketch and feature dimensions should be kept
unless directed.
Next question ≫
287 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Part A
Part B
288 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 8 of 12
For 9 points
Existing configurations
Note: The Color shown in the image may differ from your part depending on the
material assigned.
4 5 6 7
Next question ≫
289 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 9 of 12
For 9 points
Switching configuration
-Switch to configuration C
-Measure the mass of the part
Enter values
(Use . (Point) as decimal separation)
Next question ≫
290 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 10 of 12
For 9 points
-Using the part from the last question, create a new configuration named ‘Z’ based
on configuration ‘A’.
Note: Copy and Paste to create a new configuration Z may lead to an error in some
features in the new configuration. If you decide to use the Copy and Paste method,
repair this error in features before you continue.
-Create a pocket hole in four legs as indicated in the image that will be
UNSUPPRESSED in configuration Z and B and SUPPRESSED in all the other
configurations.
Enter values
(Use . (Point) as decimal separation)
Next question ≫
291 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
292 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 11 of 12
For 9 points
D1@Boss-Extrude1: 60
D1@Fillet1: 45
D1@CirPattern3: 6
Enter values
(Use . (Point) as decimal separation)
Next question ≫
293 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Question 12 of 12
For 9 points
-Using the part from the last question, stay in the current configuration.
-Look for the feature ‘CirPattern5’ in the Feature Manager Design Tree
In which configuration is the feature ‘CirPattern5’ suppressed? (Select all that apply)
A B C D X Z
Next question ≫
E N D o f E X A M S E T N o . 6
294 | E x a m S e t 6
Part 3. SEGMENT 2: Exam Set 6
Summary
Review
What’s your weakest points? (Check a couple of items and try practicing them more)
Manipulating configuration
Understanding design intent
Using design table
Modifying feature
Repairing warning and error
Creating feature
End Examination