Professional Documents
Culture Documents
ASME IX (2023) - Range Qualification WPS & Welder
ASME IX (2023) - Range Qualification WPS & Welder
IX-2023
190
ASME BPVC.IX-2023
Qualified With → F-No. 1 F-No. 1 F-No. 2 F-No. 2 F-No. 3 F-No. 3 F-No. 4 F-No. 4 F-No. 5 F-No. 5
With Without With Without With Without With Without With Without
Qualified For ↓ Backing Backing Backing Backing Backing Backing Backing Backing Backing Backing
F-No. 1 With Backing X X X X X X X X X X
F-No. 1 Without Backing … X … … … … … … … …
F-No. 2 With Backing … … X X X X X X … …
F-No. 2 Without Backing … … … X … … … … … …
F-No. 3 With Backing … … … … X X X X … …
F-No. 3 Without Backing … … … … … X … … … …
F-No. 4 With Backing … … … … … … X X … …
F-No. 4 Without Backing … … … … … … … X … …
F-No. 5 With Backing … … … … … … … … X X
F-No. 5 Without Backing … … … … … … … … … X
NOTE: (1) Deposited weld metal made using a bare rod not covered by an SFA Specification but which conforms to an
analysis listed in Table QW-442 shall be considered to be classified as F-No. 6.
202
ASME BPVC.IX-2023
QW-450 SPECIMENS
Table QW-451.1
Groove-Weld Tension Tests and Transverse-Bend Tests
Range of Thickness T of Base
Metal, Qualified, Maximum Thickness t of Type and Number of Tests Required (Tension and
Thickness T of Test in. (mm) [Notes (1), (2)] Deposited Weld Metal, Guided-Bend Tests) [Note (2)]
Coupon, Welded, Qualified, in. (mm) Tension, Side Bend, Face Bend, Root Bend,
in. (mm) Min. Max. [Notes (1), (2)] QW-150 QW-160 QW-160 QW-160
1
Less than ∕16 (1.5) T 2T 2t 2 ... 2 2
1
∕16 to 3∕8 (1.5 to 10), 1
∕16 (1.5) 2T 2t 2 [Note (5)] 2 2
incl.
3
Over ∕8 (10), but less 3
∕16 (5) 2T 2t 2 [Note (5)] 2 2
than 3∕4 (19)
3
∕4 (19) to less than 3
∕16 (5) 2T 2t when t < 3∕4 (19) 2 [Note (4)] 4 ... ...
11∕2 (38)
3
∕4 (19) to less than 3
∕16 (5) 2T 2T when t ≥ 3∕4 (19) 2 [Note (4)] 4 ... ...
11∕2 (38)
1
1 ∕2 (38) to 6 (150), 3
∕16 (5) 8 (200) [Note (3)] 2t when t < 3∕4 (19) 2 [Note (4)] 4 ... ...
incl.
1
1 ∕2 (38) to 6 (150), 3 8 (200) [Note (3)] when
∕16 (5) 8 (200) [Note (3)] 2 [Note (4)] 4 ... ...
incl. t ≥ 3∕4 (19)
Over 6 (150) 3
∕16 (5) 1.33T 2t when t < 3∕4 (19) 2 [Note (4)] 4 ... ...
[Note (6)]
Over 6 (150) 3
∕16 (5) 1.33T 1.33T when t ≥ 3∕4 (19) 2 [Note (4)] 4 ... ...
[Note (6)]
NOTES:
(1) The following variable further restricts the limits shown in this table when they are referenced in QW-250 for the process under considera-
tion: QW-403.9. Also, QW-202.2, QW-202.3, and QW-202.4 provide exemptions that supersede the limits of this table. Supplementary
essential variable requirements may also further limit thickness ranges in this table.
(2) For combination of welding procedures, see QW-200.4.
(3) For the SMAW, SAW, GMAW, PAW, LLBW, and GTAW welding processes only; otherwise per Note (1) or 2T, or 2t, whichever is applicable.
(4) See QW-151.1, QW-151.2, and QW-151.3 for details on multiple specimens when coupon thicknesses are over 1 in. (25 mm).
(5) Four side-bend tests may be substituted for the required face- and root-bend tests, when thickness T is 3∕8 in. (10 mm) and over.
(6) For test coupons over 6 in. (150 mm) thick, the full thickness of the test coupon shall be welded.
204
ASME BPVC.IX-2023
Table QW-451.2
Groove-Weld Tension Tests and Longitudinal-Bend Tests
Range of Thickness T Thickness t of Deposited Type and Number of Tests Required
of Base Metal Qualified, Weld Metal Qualified, (Tension and Guided-Bend Tests)
in. (mm) [Notes (1), (2)] in. (mm) [Notes (1), (2)] [Note (2)]
Thickness T of Test Coupon Tension, Face Bend, Root Bend,
Welded, in. (mm) Min. Max. Max. QW-150 QW-160 QW-160
Less than 1∕16 (1.5) T 2T 2t 2 2 2
1
∕16 to 3∕8 (1.5 to 10), incl. 1
∕16 (1.5) 2T 2t 2 2 2
Over 3∕8 (10) 3
∕16 (5) 2T 2t 2 2 2
NOTES:
(1) The following variable further restricts the limits shown in this table when they are referenced in QW-250 for the process under considera-
tion: QW-403.9. Also, QW-202.2, QW-202.3, and QW-202.4 provide exemptions that supersede the limits of this table. Supplementary
essential variable requirements may also further limit thickness ranges in this table.
(2) For combination of welding procedures, see QW-200.4.
Table QW-451.3
Fillet-Weld Tests
Type and Number of
Tests Required
Type of Thickness of Test Coupons [Figure QW-462.4(a) or
Joint as Welded, in. Range Qualified Figure QW-462.4(d)] Macro
Fillet Per Figure QW-462.4(a) All fillet sizes on all base metal thicknesses and all diameters 5
Fillet Per Figure QW-462.4(d) … 4
GENERAL NOTE: A production assembly mockup may be substituted in accordance with QW-181.1.1.
Table QW-451.4
Fillet Welds Qualified by Groove-Weld Tests
Thickness T of Test Coupon
(Plate or Pipe) as Welded Range Qualified Type and Number of Tests Required
All groove tests All fillet sizes on all base metal Fillet welds are qualified when the groove weld is qualified in accordance
thicknesses and all diameters with either Table QW-451.1 or Table QW-451.2 (see QW-202.2)
205
ASME BPVC.IX-2023
Table QW-452.1(a)
Test Specimens
Type and Number of Examinations and Test Specimens Required
Face Bend Root Bend
Side Bend Figure QW-462.3(a) Figure QW-462.3(a)
Thickness of Weld Metal, Visual Examination Figure QW-462.2 or Figure QW-462.3(b) or Figure QW-462.3(b)
in. (mm) per QW-302.4 [Note (1)] [Notes (1), (2)] [Notes (1), (2)]
Less than 3∕8 (10) X … 1 1
3
∕8 (10) to less than 3∕4 (19) X 2 [Note (3)] … …
3
∕4 (19) and over X 2 … …
GENERAL NOTE: The “Thickness of Weld Metal” is the total weld metal thickness deposited by all welders and all processes in the test coupon
exclusive of the weld reinforcement.
NOTES:
(1) To qualify using positions 5G or 6G, a total of four bend specimens are required. To qualify using a combination of 2G and 5G in a single test
coupon, a total of six bend specimens are required. see QW-302.3. The type of bend test shall be based on weld metal thickness.
(2) Coupons tested by face and root bends shall be limited to weld deposit made by one welder with one or two processes or two welders with one
process each. Weld deposit by each welder and each process shall be present on the convex surface of the appropriate bent specimen.
(3) One face and root bend may be substituted for the two side bends. For a test coupon welded in the 5G or 6G position, two face and two root
bends may be substituted for the four side bends in accordance with Figure QW-463.2(d). For a test coupon welded using a combination of 2G
and 5G positions, three face and three root bends may be substituted for the six side bends in accordance with Figure QW-463.2(f) or Figure
QW-463.2(g).
Table QW-452.1(b)
Thickness of Weld Metal Qualified
Thickness, t, of Weld Metal in the Coupon, in. (mm)
[Notes (1), (2)] Thickness of Weld Metal Qualified [Note (3)]
All 2t
1
∕2 (13) and over with a minimum of three layers Maximum to be welded
NOTES:
(1) When more than one welder, process, or set of essential variables is used during welding of a test coupon, the thickness, t, of the weld metal in
the coupon deposited by each welder, for each process, and with each set of essential variables shall be determined and used individually in
the “Thickness, t, of Weld Metal in the Coupon” column to determine the “Thickness of Weld Metal Qualified.”
(2) Two or more pipe test coupons with different weld metal thickness may be used to determine the weld metal thickness qualified and that
thickness may be applied to production welds to the smallest diameter for which the welder is qualified in accordance with Table QW-452.3.
(3) Thickness of test coupon of 3∕4 in. (19 mm) or over shall be used for qualifying a combination of three or more welders each of whom may use
the same or a different welding process.
Table QW-452.3
Groove-Weld Diameter Limits
Outside Diameter Qualified, in. (mm)
Outside Diameter of Test Coupon, in. (mm) Min. Max.
Less than 1 (25) Size welded Unlimited
1 (25) to 27∕8 (73) 1 (25) Unlimited
Over 27∕8 (73) 27∕8 (73) Unlimited
GENERAL NOTES:
(a) Type and number of tests required shall be in accordance with QW-452.1.
(b) 27∕8 in. (73 mm) O.D. is the equivalent of NPS 21∕2 (DN 65).
206
ASME BPVC.IX-2023
Table QW-452.4
Small Diameter Fillet-Weld Test ð23Þ
Table QW-452.5
Fillet-Weld Test
Type and Number of
Tests Required
[Figure QW-462.4(b)
or Figure
Thickness of Test Coupon QW-462.4(c)]
Type of Joint as Welded, in. (mm) Qualified Range, in. (mm) Macro Fracture
3
Tee fillet ∕16 (5) or greater All base material thicknesses, fillet sizes, and diameters 27∕8 1 1
[Figure QW-462.4(b)] (73) O.D. and over [Note (2)]
Less than 3∕16 (5) T to 2T base material thickness, T maximum fillet size, and all 1 1
diameters 27∕8 (73) O.D. and over [Note (2)]
GENERAL NOTE: Production assembly mockups may be substituted in accordance with QW-181.2.1.
NOTES:
(1) Test coupon prepared as shown in Figure QW-462.4(b) for plate or Figure QW-462.4(c) for pipe.
(2) 27∕8 in. (73 mm) O.D. is considered the equivalent of NPS 21∕2 (DN 65). For smaller diameter qualifications, refer to Table QW-452.4 or Table
QW-452.6.
Table QW-452.6
Fillet Qualification by Groove-Weld Tests
Thickness of Test Coupon Type and Number
Type of Joint as Welded, in. (mm) Qualified Range of Tests Required
Any groove All thicknesses All base material thicknesses, fillet sizes, Fillet welds are qualified when a welder or
and diameters welding operator qualifies on a groove weld test
207
ASME BPVC.IX-2023
Table QW-453
Procedure and Performance Qualification Thickness Limits and Test Specimens for Hard-Facing (Wear-Resistant) and
Corrosion-Resistant Overlays
Corrosion-Resistant Overlay Hard-Facing Overlay (Wear-Resistant)
Thickness of Nominal Base Metal Nominal Base Metal Type and Number of
Test Coupon (T) Thickness Qualified (T) Type and Number of Tests Required Thickness Qualified (T) Tests Required
Procedure Qualification Testing
Less than 1 in. T qualified to unlimited Liquid penetrant T qualified up to 1 in. (25 Liquid penetrant
(25 mm) T mm) 3 hardness readings
per specimen
1 in. (25 mm) and 1 in. (25 mm) to unlimited 2 transverse side bend and 2 longitudinal side 1 in. (25 mm) to unlimited Macro test
over T bend, or 4 transverse side bend
Performance Qualification Testing
Less than 1 in. T qualified to unlimited 2 transverse side bend per position T qualified to unlimited Liquid penetrant
(25 mm) T
1 in. (25 mm) and 1 in. (25 mm) to unlimited 1 in. (25 mm) to unlimited Macro test
over T
208
ASME BPVC.IX-2023
QW-460 GRAPHICS
QW-461 POSITIONS
Figure QW-461.1
Positions of Welds — Groove Welds
GENERAL NOTES:
(a) The horizontal reference plane is taken to lie always below the weld under consideration.
(b) Inclination of axis is measured from the horizontal reference plane toward the vertical.
(c) Angle of rotation of face is measured from a line perpendicular to the axis of the weld and lying in a vertical plane containing this axis. The
reference position (0 deg) of rotation of the face invariably points in the direction opposite to that in which the axis angle increases. The angle
of rotation of the face of weld is measured in a clockwise direction from this reference position (0 deg) when looking at point P.
209
ASME BPVC.IX-2023
Figure QW-461.2
Positions of Welds — Fillet Welds
210
ASME BPVC.IX-2023
Table QW-461.9
Performance Qualification — Position and Diameter Limitations
(Within the Other Limitations of QW-303)
Position and Type Weld Qualified [Note (1)]
Qualification Test Groove Fillet or Tack [Note (2)]
Plate and Pipe Over
Weld Position 24 in. (610 mm) O.D. Pipe ≤24 in. (610 mm) O.D. Plate and Pipe
Plate — Groove 1G F F [Note (3)] F
2G F, H F, H [Note (3)] F, H
3G F, V F [Note (3)] F, H, V
4G F, O F [Note (3)] F, H, O
3G and 4G F, V, O F [Note (3)] All
2G, 3G, and 4G All F, H [Note (3)] All
Special Positions (SP) SP, F SP, F SP, F
Plate — Fillet 1F ... ... F [Note (3)]
2F ... ... F, H [Note (3)]
3F ... ... F, H, V [Note (3)]
4F ... ... F, H, O [Note (3)]
3F and 4F ... ... All [Note (3)]
Special Positions (SP) ... ... SP, F [Note (3)]
Pipe — Groove 1G F F F
[Note (4)] 2G F, H F, H F, H
5G F, V, O F, V, O All
6G All All All
2G and 5G All All All
Special Positions (SP) SP, F SP, F SP, F
Pipe — Fillet 1F ... ... F
[Note (4)] 2F ... ... F, H
2FR ... ... F, H
4F ... ... F, H, O
5F ... ... All
Special Positions (SP) ... ... SP, F
NOTES:
(1) Positions of welding as shown in Figures QW-461.1 and QW-461.2.
F = Flat
H = Horizontal
V = Vertical
O = Overhead
SP = Special Positions (see QW-303.3)
(2) Tack welds are not limited by pipe or tube diameters when their aggregate length does not exceed 25% of the weld circumference.
(3) Pipe 27∕8 in. (73 mm) O.D. and over.
(4) See diameter restrictions in Tables QW-452.3, QW-452.4, and QW-452.6.
214