Professional Documents
Culture Documents
FOSROC Nitoproof 30 Submittal
FOSROC Nitoproof 30 Submittal
Technical Submittal
NITOPROOF 30
(Rubberised bitumen emulsion)
Technical Datasheet
1
MY – November 2016
Nitoproof 30 constructive solutions
(Formerly Nitoproof 30HL)
Uses Properties
Provides a highly effective waterproof membrane, with Form : Dark brown liquid
cost and labour saving supplementary benefits. It can Specific gravity : 1.00
be used in a wide range of applications : Solids content : 60 to 65%
Rubber content : Approx. 10 %
Damp proof membrane in ‘sandwich construction’.
Drying time : 30 mins at 25°C
Dual purpose waterproofer and curing compound. Overcoating time : 1 hour @ 25°C
Labour saving, single component material which is Damp proof membrane and vertical vapour barrier
also water based, and therefore non-toxic.
Apply Nitoproof 30 at the rate of 1m² per litre, to give a minimum
Environmentally friendly, non-flammable, asbestos dry film thickness of 600 microns, as per CP102:1973.
free and can be used in confined spaces.
For vertical applications, ensure that there is no material sag.
Excellent service life - resistant to chloride and This can be best achieved by multiple coat applications at a
sulphate ions. maximum rate of 200 microns per coat. For multiple coat
application, the second coat should be applied at right angles
Versatile - highly extensible.
to the first. All applications should be continued up verticals to
the existing damp proof course. Ensure that the membrane
Standards compliance
is not punctured or damaged during subsequent applications.
Nitoproof 30 complies with the concrete curing
Where the surface is to receive a render or plaster finish, a
requirements of ASTM C309, when applied at the rate
keyed surface should be formed by ‘gritting’ the second coat
of 4m2 per litre.
with clean, dry sand. Allow a minimum of 48 hours drying
period before applying a plaster, render or floor screed.
Description
Flooring adhesive
Nitoproof 30 is a rubber reinforced, bitumen emulsion.
It is supplied as a single component liquid, dark brown Nitoproof 30 is a very effective waterproof adhesive for laying
in colour, which dries to form a black, flexible coating. wood blocks, cork, asphalt and asbestos tiles. The surface
should be clean, dry and smooth. Nitoproof 30 should be
Nitoproof 30 is available in drums and may be applied
applied to the floor screed using a notched trowel, and then
directly to the substrate by brush or squeegee.
left to become tacky after which the tiles should be pressed
firmly into place.
Specification
Any contamination of the tile’s upper surface should be
Where shown on the contract documents, below
cleaned immediately using a cloth - refer to any special
ground surfaces shall be protected with Nitoproof 30, a
recommendations made by the tile manufacturer.
rubberised bitumen emulsion, applied at the rate of 1
m2 per litre giving a total dry film thickness of minimum
600 microns.
1
Nitoproof 30
MY – November 2016
Nitoproof 30 is suitable for bonding insulation materials (actual coverage rates will depend upon substrate porosity)
such as polystyrene, fibreboard and cork slabs to walls
and floors. General use : 1m² per litre to give 600
microns dft
The two surfaces to be bonded must be clean, level 2
Curing compound : 4m per litre per coat
and free from all points of contact. Nitoproof 30 should
to give 150 micron dft
be applied to both surfaces and left to become tacky
(colour begins to darken). The two surfaces should
Storage
then be pressed firmly and evenly together.
Nitoproof 30 will have a minimum shelf life of 12 months
Repairs
if stored in normal warehouse conditions between 15 and
Any damaged areas can be readily overcoated to 40°C. Protect from temperatures below 10°C.
restore the membrane continuity - provided the surface
is properly prepared. Precautions
Cleaning Fire
Nitoproof 30 can be removed using only clean water, Fosroc Solvent 102 is flammable. Ensure adequate
whilst still damp. If left to dry, then Fosroc Solvent 102* ventilation, do not use near a naked flame and do not
must be used. smoke during use.
Flash point
Limitations
Fosroc Solvent 102 : 33°C
Nitoproof 30 is not a structural adhesive,
therefore mechanical fixing should be used Health and safety
where appropriate. Some people are sensitive to resins and solvents, so
Application should not commence below 6°C or gloves and barrier creams (e.g. Kerodex Antisolvent)
above 45°C. should be used when handling these products. Remove
Avoid application during windy atmospheric any contamination from the skin with soap and water, or
conditions. Application during such periods might resin removing creams (e.g. Kerocleanse Standard
cause cracking. Grade Skin Cleaner) followed by washing with soap and
water. Do not use solvent.
For application in harsh climatic conditions,
‘Nitoproof 600’ is recommended. The use of goggles is also recommended, but should
accidental eye contamination occur, wash thoroughly
Estimating with plenty of clean water and seek medical treatment
immediately.
Supply
Nitoproof 30 : 20 and 200 litre drums
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control
over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
not in accordance with any advice, specification, recommendation of information given by it.
Fosroc Sdn. Bhd.
No 8 Jalan Trompet, 33/8
Seksyen 33, 40400 Shah Alam telephone: fax: email:
Selangor, Malaysia. +60 3 5102 5660 +60 3 5102 5668 malaysia@fosroc.com
www.fosroc.com
constructive solutions
Material Safety
Datasheet
Revision date: 23/11/2016 Revision: 03 Supersedes date: 06/08/2015
1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses Waterproofing Coating / Membrane
Human health The product contains a sensitising substance which may provoke an allergic reaction among
sensitive individuals.
Pictogram
1/7
Revision date: 23/11/2016 Revision: 03 Supersedes date: 06/08/2015
NITOPROOF 30
Supplementary precautionary P321 Specific treatment (see medical advice on this label).
statements P333+P313 If skin irritation or rash occurs: Get medical advice/ attention.
P362+P364 Take off contaminated clothing and wash it before reuse.
3.2. Mixtures
The Full Text for all R-Phrases and Hazard Statements are Displayed in Section 16.
Ingestion Do not induce vomiting. If vomiting occurs, the head should be kept low so that stomach vomit
doesn't enter the lungs. Get medical attention if a large quantity has been ingested.
Skin contact Remove affected person from source of contamination. Remove contaminated clothing and
rinse skin thoroughly with water.
Eye contact Flush eyes with water at least 15 minutes. Get medical attention if eye irritation develops or
persists.
Remove contact lenses.
4.2. Most important symptoms and effects, both acute and delayed
General information The severity of the symptoms described will vary dependent on the concentration and the
length of exposure.
Skin contact Prolonged skin contact may cause redness and irritation.
4.3. Indication of any immediate medical attention and special treatment needed
Notes for the doctor Treat symptomatically.
2/7
Revision date: 23/11/2016 Revision: 03 Supersedes date: 06/08/2015
NITOPROOF 30
Advice on general Do not eat, drink or smoke when using this product. Good personal hygiene procedures
occupational hygiene should be implemented.
Protective equipment
Appropriate engineering Provide adequate general and local exhaust ventilation. Avoid inhalation of vapours.
controls
Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible.
3/7
Revision date: 23/11/2016 Revision: 03 Supersedes date: 06/08/2015
NITOPROOF 30
Hand protection Chemical resistant gloves required for prolonged or repeated contact.
Hygiene measures Do not smoke in work area. Wash hands and any other contaminated areas of the body with
soap and water before leaving the work site.
Respiratory protection No specific recommendations. Respiratory protection may be required if excessive airborne
contamination occurs.
Colour Black.
Odour Typical
pH 9-10
10.1. Reactivity
Reactivity Stable
4/7
Revision date: 23/11/2016 Revision: 03 Supersedes date: 06/08/2015
NITOPROOF 30
Inhalation Gas or vapour in high concentrations may irritate the respiratory system.
Eye contact Vapour or spray in the eyes may cause irritation and smarting.
12.1. Toxicity
Toxicity Not considered toxic to fish.
Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.
General The product is not covered by international regulations on the transport of dangerous goods
(IMDG, IATA, ADR/RID).
14.1. UN number
Not applicable.
5/7
Revision date: 23/11/2016 Revision: 03 Supersedes date: 06/08/2015
NITOPROOF 30
14.7. Transport in bulk according to Annex II of MARPOL and the IBC Code
Transport in bulk according to Not applicable.
Annex II of MARPOL 73/78
and the IBC Code
15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulations No listing known. The Chemicals (Hazard Information and Packaging for Supply) Regulations
2009 (SI 2009 No. 716). Control
of Substances Hazardous to Health Regulations 2002 (as amended).
General information The data and advice given apply when the product is used for the stated application or
applications. The product
is not sold as suitable for any other application. Use of the product for applications other than
as stated in this sheet may give rise to risks not mentioned in this sheet. The product should
not be used other than for the stated application or applications without seeking advice from
Fosroc Ltd.
If this product has been purchased for supply to a third party for use at work, it is the
purchaser's duty to take all
necessary steps to secure that any person handling or using the product is provided with the
information in this
sheet.
It is the responsibility and duty of the employer to inform employees and others who may be
affected of any hazards described in this sheet and of any precautions which should be taken.
This sheet does not constitute or substitute for the users own assessment of workplace risk,
as required by other health and safety legislation.
Further copies of this Safety Data Sheet may be obtained from Fosroc Korea Limited.
6/7
Revision date: 23/11/2016 Revision: 03 Supersedes date: 06/08/2015
NITOPROOF 30
Revision 03
The information on this data sheet represents our current data and is reliable provided that the product is used under the
prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance
literature. Any other use of the product which involves using the product in combination with any other product or any other
process is the responsibility of the user.
7/7
constructive solutions
Method Statement
method statement constructive solutions
Nitoproof 30
Section A : General Comments
l Comments
High temperature working
It is suggested that, for temperatures above 35°C, the following guidelines are adopted as good
working practice:
(i) Store unmixed materials in a cool (preferably temperature controlled) environment, avoiding
exposure to direct sunlight.
(ii) Keep equipment cool, arranging shade protection if necessary. It is especially important to
keep cool those surfaces of the equipment, which will come into direct contact with the material
itself.
(iii) Try to avoid application during the hottest times of the day, arrange temporary shading as
necessary.
(iv) Make sufficient material, plant and labour available to ensure that application is a continuous
process.
Equipment
It is suggested that the following list of equipment is adopted as a minimum requirement.
Protective clothing : Protective overalls
: Good quality gloves, goggles and face mask
Preparation equipment : Stiff wire brush
: Soft brush
: Air compressor
Application equipment : Brush / Roller / Squeegee
Fosroc operates a policy to encourage the use, where possible, of approved or licensed applicators.
This ensures that repairs are completed satisfactorily so that the long-term performance of the
materials is assured. For contractors who wish to apply the materials themselves Fosroc is also able
to offer technical assistance and training, either on-site or at its Training Centre in Dubai.
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control
over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
Fosroc Sdn. Bhd. not in accordance with any advice, specification, recommendation of information given by it.
www.fosroc.com
constructive solutions
1.0 Preparation
1.1 Clean the surface free of oil, grease and all loosely adhering particles, by stiff wire brushing.
1.2 Follow step 1 by soft brushing and blowing of dry, oil-free compressed air.
2.0 Application
2.2 Apply one coat of Nitoproof 30, using a brush, squeegee or roller at a minimum rate of
200microns per coat.
2.3 Apply the second coat at right angle to the first, after the first coat has dried fully
(approximately 4hours from application).
2.4 Damaged areas of Nitoproof 30 can be readily overcoated to restore the continuity of the
membrane.
3.0 Cleaning
3.1 Immediately after application, clean all tools and equipment with clean water. If the product
dries on the tools, use Fosroc Solvent 102.
This method statement is offered by Fosroc as a ‘standard proposal’ for the application of Nitoproof
30. It remains the responsibility of the Engineer to determine the correct method for any given
application.
Where alternative methods are to be used, these must be submitted to Fosroc for approval, in
writing, prior to commencement of any work. Fosroc will not accept responsibility or liability for
variations to the above method statement under any other condition.
Page 2 of 2
constructive solutions
Test Reports
constructive solutions
Job References
Job References for Nitoproof 30
Sorted by ascending Project Category and ascending Project Date
Sector Segment Project Product Name Client Consultant Date UOM Qty Sold
SAUDI ARABAIN NATIONAL
Saudi Arabia Ministry Of
GUARD PROJECT- SANG - Nitoproof 30 (200l) Arabian Architecture 2017 L 30
Defense & Aviation
Mixed BAHRA
Buildings
Development SAUDI ARABAIN NATIONAL Yenigun Construction
GUARD PROJECT- SANG - Nitoproof 30 (200l) Industry & Comm. Inc.--- Dar Al Handasah 2017 L 60
TAIF Taif
Fosam North Jeddah
Airport KAIA PROJECT Nitoproof 30 (25l) Showroom Cash Sales- Unknown 2017 L 111
Transport Safari
RIYADH METRO PROJECT- Arriyadh Development
Rail Nitoproof 30 (25l) Aecom 2017 L 162
LINE 1&2 Authority
Public &
Buildings SANG HOSPITAL Nitoproof 30 (200l) National Guards Dar Al Handasah 2016 L 30
Institution
RIYADH METRO PROJECT- Arriyadh Development
Transport Rail Nitoproof 30 (200l) Aecom 2016 L 12
LINE 1&2 Authority