Professional Documents
Culture Documents
English CactusLevel4 Instructions PDF
English CactusLevel4 Instructions PDF
English CactusLevel4 Instructions PDF
11 parts
Time to create ~ 1.5 hour
.com
OXYGAMI
13 cm
(5.2 in)
25 cm
(9.8 in)
Cactus Level 4
This file is free and sharable if shared as is. Can not be sold.
THE PRINCIPLE
1
There’s nothing too complicated, as you’ll see. Everything will be fine after a couple of minutes.
CUT OFF SCORE FOLD FOLLOW THE FIND THE MATCHING POINTS
PART NAMES AND GLUE TOGETHER
valley fold = fold up
mountain fold = fold down
1
1A
1
4
4
52
1A
50 51
5
B printed side
1B 1B 6 8
10
6
1C
8
EQUIPMENT YOU’LL NEED
LEGEND
3A BIG NUMBERS. EXAMPLE OF AN UNFOLDED PART
In both the template and instructions, these are the part names.
circles = start here! (the pair is
They will guide you through the order of assembly. to be found within the same part)
118 CIRCLES.
In the template itself, they indicate that there are numbers to be glued 67
67
together within the part, and even suggest to start here. Time-saving trick!
3A
DARKENED FLAPS.
There may be some at the back of big sculptures. Don’t fold them, so
EXAMPLE OF A FOLDED PART
you’ll get a perfectly flat back. Those flaps differ from the others just
to draw your attention :)
1A
PINK DOTS. +1B
In these instructions, they help you see where you should start to glue
the next part. Then you just need to follow the next flaps. Obviously
previous part part to glue
you can do as you please. If in doubt, the small numbers are here to
confirm you are on the right track. pink dot = starting point
.com
OXYGAMI
http://oxygami.com
http://bit.ly/OxygamiSite 2/4 stephane@oxygami.com
TIPS & TRICKS
#0 HOW TO SCORE.
Use a ruler with / a dried out ball point pen / the tip of a pointy object (compasses) / the dull side of a knife or
X-acto knife. If it gets though the sheet, then this is not the right tool. Batch your pieces to save time.
#2 SYSTEMATISE.
1 Printed side face to you 4 Still with the printed side face to you 7 Flip the part
-----------------------------------
2 Push all the (red) small-dotted lines outwards 5 Pull all the (blue) large-dotted lines towards you 8 Appy the glue on the flaps
----------------------------------- (non-printed side).
3 Unfold 6 Unfold
10
9. 11 12 a few tiny drops of glue
1B
12
14
13 11
4
14
10 5 1
9. 6
14
8
1B 4
1
6. 5
#6 USE VERY LITTLE GLUE (ALONG THE OUT EDGE OF THE FLAPS).
A thin line of glue or a few tiny drops are more than enough, or it will spread and spoil the outside
of your sculpture. If it happens, scrape out the surplus with your nail, then rub the paper with a little saliva.
part 1
visible part 1
flap !!
part 2 part 2
When adding a new part, take Firmly hold the corners first, Now that the first end of Again, press the corner Keep holding it while aligning
a moment to be sure the until the glue sticks (5 sec.) the next tab is in place, first and wait 5 seconds. the middle of the tab. (when
first flap aligns accurately and then press the rest. it will be easy to align the it comes to longer flaps, press
with its matching edge. second end of it. for another 5 sec). Then press
back & forth between the 2 ends.
4 +4 +5
+6 +7 +8
+9 +10 +11
.com
OXYGAMI
http://oxygami.com 4/4 stephane@oxygami.com