Professional Documents
Culture Documents
Design and Build Your Own 3D Printed RC Plane
Design and Build Your Own 3D Printed RC Plane
by Iqbal Samin
Hey everyone, I'm excited to take you on a wild ride through my journey designing and building a 3D printed RC plane.
This isn't your typical how-to guide. Think of it as a build log infused with my ups, downs, and valuable lessons learned.
Whether you're an experienced pilot or just starting out, this guide is for you. While some experience in RC planes and 3D
printing helps, I'm here to help you regardless of your expertise. (I love replying to your questions in the comments!)
What You'll Discover:
In this tutorial, I'll break down the entire process step by step, from designing the fuselage, wings, V-tails, canopy, and
motor cover, to 3D printing these components, assembling your plane, and nally, launching it into the sky.
The Build Log Chronicles:
But here's where it gets interesting. I'm not just sharing the awless path to success. I'll be honest about the hiccups, the
crashes, and the mistakes. For example, to save some bucks and avoid a costly 3D printed wing, I initially experimented
with foam. And yes, there were crashes, but each one taught me something valuable.
I am Prithul, currently an engineering exchange student at the Fox Valley Tech Appleton, WI, and this was my last 3D
printing project before leaving my home country Bangladesh. Ready to build one yourself? Let's take o !
Supplies:
Before we dive into the design and building process, let's make sure we have everything we need to get started. Here's a
list of the essential materials and tools you'll want to have on hand:
Materials:
1. PLA Filament: Choose a PLA lament that prints best on your 3D printer. PLA+ is a good choice for its
added strength and a ordability. I used SUNLU PLA+ laments but there are some light-weight PLA
laments that might work better for their, well, light weight. My plane used only around 342 grams of
lament so a 1KG spool should be enough for you.
2. Electronics Components: These may include
3. 1200-2200kv Brushless Motor. I used a Turnigy D3530 1100kv motor.
4. An Electronic speed controller (ESC) suitable for your motor. I used a generic 40A ESC.
5. LiPo battery: I suggest using 3S 1500-2200mAH batteries.
6. Transmitter and receiver: I used a Flysky FS-i6
7. 3x 9g servos. Any generic servos would work but metal gear ones last longer.
8. Screws and Fasteners: You will need a few M3 screws and nuts to mount the motor and locked the
carbon rod to the fuselage and V-tail.
9. Carbon rod: You can nd these at your local hobby shop or online ones like HobbyKing. You will need:
10. 600mm long - 16mm carbon rod. This rod helps us save a lot of weight and connects the tail to the
fuselage.
11. 1200mm long - 3mm or 4mm carbon rod for wing spur.
Design and Build Your Own 3D Printed RC Plane: Page 1
12. Control Linkages: Thin wires or pushrods for connecting servos to control surfaces.
Tools:
1. 3D Printer: You'll need access to a 3D printer with a bed size of at least 200x200x200
2. Fusion 360 Software: This computer-aided design (CAD) software will be your primary tool for
designing your RC plane.
3. Calipers: A good set of digital calipers is greatly helpful for taking measurements of the motor, battery,
and other electronics that t into the 3D design.
4. Screwdrivers and Allen Keys
5. Soldering Iron (may not be necessary)
6. Super glue: To join the 3D printed parts. Additionally, a spray super glue activator will save you some
time.
7. Safety Gear: Don't forget safety glasses, hand gloves, and a well-ventilated workspace, especially when
you're gluing the parts together.
That's it! As you progress through the steps, you may nd additional tools or materials are needed for speci c tasks.
Before we jump into the designing, let's take a moment to plan our RC plane. This crucial step will help you de ne your
project's direction and ensure a successful build.
1. Decide on the Type of RC Plane:
Consider whether you want to build a trainer plane, a sporty aerobatic model, a war plane, a glider, or
something entirely unique.
Think about your ying preferences and skill level.
You might want to take some time to think of the di erent styles of tail you can have like traditional
inverted T-tail, T-tail, or a V-tail which I went with.
I went with a glider since they usually need less structural strength, and are easier to y at slower speeds.
5. Additional Resources:
For detailed guidance on wing shapes, airfoils, and size calculations, you can refer to these tutorials or
resources:
https://rcplanes.online/design.htm (photo used from this site for this step)
https://www. itetest.com/articles/what-if-i-want-to-design-an-airplane
By taking the time to plan your RC plane's characteristics and speci cations, you'll be making sure the plane will actually
generate lift and y.
Designing the fuselage is a pivotal step in creating your 3D printed RC plane. Follow these steps to ensure a sturdy, well-
tting fuselage that accommodates your electronics and maintains balance.
1. Import Airfoil Drawing:
Begin by importing the airfoil drawing you've selected into Fusion 360. This will serve as the foundation
for your fuselage design.
Here's a quick video showing how you can import airfoil DAT les into Fusion 360:
https://www.youtube.com/watch?v=3Huj4tK-V3U
7. Motor Mount:
At the front of the fuselage, ensure that you have a motor mount plate/surface to accommodate your
chosen motor.
You can simply google the dimensions for your motor mount and add the holes accordingly.
I added a hole near the motor to let some of the upcoming air into the fuselage. Additional holes were
added in the back for the air to escape.
Pro tips:
It's always a good idea to create a dummy model of your motor, battery, and receiver with correct
dimensions to ensure they will t into the fuselage. Try not to get the dimensions of your battery wrong
while converting inches into millimeters like I did *oops*
Don't divide the fuselage right where you think the weakest point might be. The joints are most prone to
breaking on rough landings. It takes some guess work but try to have the joint where there are additional
support from the canopy or wing.
Throughout this process, precision and careful consideration of component placement are key.
Remember that the fuselage is not just a housing; it plays a vital role in the aerodynamics and it will take
the most hit on landings. Keep strength in mind but balance the strength and weight.
https://youtu.be/KFR8G6GzX7o
Download
https://www.instructables.com/FXA/P5N7/LMYWHQG5/FXAP5N7LMYWHQG5.mp4
Personal Experience:
Before we dive into creating the wings, let me share a bit from my own journey. Initially, I opted for a foam wing while
using a 3D printed fuselage and V-tail. It was a slow start, as I wasn't entirely sure if a fully 3D printed plane would y
without being too heavy. But sometimes in this hobby, curiosity leads to great discoveries. The 3D printed fuselage and
V-tail performed remarkably well, which gave me the con dence to go ahead and design the 3D printed wing. It was a
leap of faith, and it paid o . (It did crash and break the fuselage once giving me more ideas on the weak-points of my
fuselage)
Now, let's get into the details of designing your wings.
1. Transform Airfoil Sketch:
Start with the airfoil sketch from your previous calculations. Extrude or loft it to create a solid shape.
You may want to adjust the size and consider using a smaller airfoil at the tip to create a tapered wing.
Pro Tip: Adding some extra surface area where the printed parts are glued together helps super glue create a stronger
joint. Additionally, experiment with di erent in ll angles that your printer can handle; a 45-degree angle is a good
starting point.
With these steps, you're well on your way to crafting a set of wings that will complement your 3D printed RC plane
perfectly. The combination of strength, weight optimization, and precise design will be essential for successful ights.
https://youtu.be/aDgyn36Maa8
Creating well-balanced and aerodynamic V-tails for your RC plane is essential for a stable ight. Follow the following
steps to design your V-tails. Carefully watch the animated GIF attached above to get a gist of the whole designing
process.
1. Drawing the guides:
Start by sketching a line at the desired V-tail angle. In my case, I wanted the tail to be at a 38 degree angle
from the horizon. The length of the line should be your tail length.
Draw a perpendicular line at the bottom and tip of the line.
Draw plains across the perpendicular lines, you will have your airfoils imported into sketches on these
plains.
6. Servo Placement:
Add a hole in the V-tail to insert and securely glue the servo in place. This will save us a lot of air drag as
the servo integrates into the body.
Ensure the servo placement aligns with your control rod. I personally prefer not designing the control
horn into the 3D print, and instead gluing on some custom 3D printed control horn later.
https://www.thingiverse.com/thing:781066
8. Rod Mount:
In the center of the V-tails, create a rod mount that ts onto the control rod and securely holds both tail
sections together.
As with the fuselage, you should add some screw holes to grab onto, or screw into the carbon rod.
Designing V-tails requires precision and symmetry to maintain stabili during ight. By following these steps, you'll
ensure your RC plane's control surfaces are not only functional but also aerodynamically e cient.
https://youtu.be/_f1GgJtQkTI
By following these steps, you'll not only provide essential protection for your motor but also signi cantly enhance the
aerodynamics of your RC plane, leading to improved performance and a smoother ight experience.
Before you start 3D printing your RC plane components, it's crucial to ensure that your 3D printer is well-prepared and
calibrated for the job. Here are the essential steps to get you started:
1. Printer Calibration:
Begin by calibrating your 3D printer. Check the bed leveling, extruder calibration, and ensure that the
printer's mechanics are in good condition.
3. Temperature Settings:
Experiment with temperature settings to nd the ideal temperature for your speci c lament. It's
typically recommended to start with the lament manufacturer's recommended temperature and make
adjustments from there.
7. Printer Maintenance:
Ensure your 3D printer is well-maintained. Clean the nozzle, lubricate moving parts, and replace worn-out
components as needed.
8. Printer Readiness:
Con rm that your 3D printer is ready for continuous operation. Make sure you have enough lament
spools and that your print bed is clean and properly prepared with adhesion aids if necessary.
Now you should be ready to go ahead and print all the parts. I will warn you though that it takes a lot of time and it is
easy to become impatient. Try to nd some other short project in the meantime to keep yourself busy.
Now that you have all your meticulously designed and 3D printed components ready, it's time to bring your RC plane to
life through assembly. Follow these steps to put everything together:
1. Prepare Your Workspace:
Set up a clean, well-lit and well-ventileted workspace with enough room to spread out your parts and
work comfortably. Ensure you have all the necessary tools and materials within reach. Having a pieces of
waste cloth helps clean o excess super glue.
2. Fuselage Assembly:
Start by sanding the joints where super glue would go on.
Since we've designed it to be in multiple parts for 3D printing, align them carefully and use super glue to
secure the pieces together.
Take advantage of the added surface area you designed for stronger joints.
Lastly, install the carbon rod and secure it with screws.
4. Wing Installation:
Carefully insert the wings into the cutout sections on the fuselage, ensuring they sit securely and at the
correct angle.
You can use screws, rubber-bands, or more super to hold the wings in place. (I used tapes!)
6. Servo Linkage:
Connect the V-tail and wing control horns to the servo control linkages.
Ensure they move freely through the whole range of motion and are correctly oriented for control.
With your 3D printed parts skillfully assembled, your RC plane is ready to take the electronics. Take your time during this
phase, ensuring precision and attention to detail. Once the assembly is complete, you'll be just one step away from ying
your custom-built plane.
It's time to equip your plane with the essential electronic components. Follow these steps to ensure a seamless
installation:
1. Gather Your Electronics:
Before you begin, make sure you have all the necessary electronic components ready: a brushless motor,
electronic speed controller (ESC), LiPo battery, receiver, and servos. Double-check that they are
compatible with your RC plane's design.
2. Motor Installation:
Begin by mounting the brushless motor at the front of the fuselage, following the motor speci cations
provided by the manufacturer.
Ensure the motor's shaft protrudes correctly through the motor cover.
4. Receiver Placement:
Position the receiver securely inside the fuselage, ensuring it is well-protected and have the antenna(s)
sticking out.
Connect the receiver to the appropriate channels for throttle, elevator, rudder, and aileron control.
5. Servo Installation:
Mount the servos in their designated locations, typically near control surfaces such as ailerons, elevators,
and rudders with hot glue.
Use plenty of hot glue to make sure there is no play in the servo mount.
Securely attach the servo horns or linkages to the control surfaces.
7. Battery Placement:
Insert the LiPo battery into the fuselage, ensuring it is securely fastened and well-balanced for stable
ight.
Caution:
You might need to calibrate the ESC, follow the manufacturer's instructions.
With the electronics successfully installed and calibrated, your 3D printed RC plane is nearly ready for its maiden ight.
Be thorough in your installation and testing to ensure a safe and enjoyable ying experience.
With these checks complete, you're ready for a con dent and enjoyable ight with your 3D printed RC plane.
Now that your 3D printed RC plane is assembled and prepped, it's time to take it for its maiden ight.
Takeo :
Gradually increase throttle to initiate takeo , gently throw the plane with your dominant hand while holding the throttle
on the other hand. The plane should naturally want to stay oated and straight up. Gently take the plane up with light
movements on the elevator. Extreme movements can stall the plane.
Flight Testing:
Begin with gentle maneuvers to assess stability and control. Test each control surface to ensure they respond as
expected. Observe the plane's behavior during di erent ight conditions.
Troubleshooting:
If you encounter any issues such as instability, erratic behavior, or control problems, land the plane safely as soon as
possible. Analyze the issue and make necessary adjustments to the aircraft or electronics. Common troubleshooting
steps may include checking control surface linkages, CG adjustments, and recalibrating electronics. If you're unsure
about the issue, consult experienced online forums or comment below!
Landing:
Plan a gentle descent for landing, keeping the approach smooth and controlled. Touch down softly to avoid damage to
the printed body.
Post-Flight Inspection:
After the test ight, inspect the plane for any damage, loose super glue joint or wear. Recharge the battery and ensure all
components are ready for the next ight. The great thing about a 3D printed plane is you ca easily re-print any part of the
plane and replace it!
https://youtube.com/shorts/YjPIxu0b5UQ?feature=share
Each test ight is an opportunity to learn about your aircraft and improve its performance.
For safety, consider starting with simple ight maneuvers and gradually progressing to more complex maneuvers as you
become familiar with your RC plane's behavior. You may want to keep a ight log to track your experiences and
adjustments. With these steps, you'll be well-prepared for your test ight and equipped to address any challenges that
may arise during the initial ights of your 3D printed RC plane. Happy ying!