Professional Documents
Culture Documents
Rotor Brake System (Re-Activation) - Operation
Rotor Brake System (Re-Activation) - Operation
Rotor Brake System (Re-Activation) - Operation
com/amerigo/ietp/printDocument
Table of contents
References
Preliminary Requirements
Procedure
Requirements After Job Completion
List of tables
1 References
2 Access points
3 Zones
4 Required Conditions
5 Support Equipment
6 Supplies
7 Spares
List of figures
1 Rotor brake system (Re-Activation) - Operation (Sheet 1 of 2)
1 Rotor brake system (Re-Activation) - Operation (Sheet 2 of 2)
References
Table 1 References
Data Module Title
69-A-63-51-03-00A-720A-A Rotor brake caliper - Install procedure
69-A-63-51-03-00A-520A-A Rotor brake caliper - Remove procedure
Table 3 Zones
Zone ID Data Module
No Zones
Preliminary Requirements
Required Conditions
Table 4 Required Conditions
Conditions Data Module/Technical Publication
The rotor brake caliper must be removed 69-A-63-51-03-00A-520A-A
1 of 6 18/03/2020 20:29
AW169 IETP 14th Issue - Unmaintained Copy https://leonardo.agustawestland.com/amerigo/ietp/printDocument
Support Equipment
Table 5 Support Equipment
Nomenclature Identification No. Qty
RBCA electrical checker AJ-11-00 1
Torque wrench ZZ-50-04 1
Supplies
Table 6 Supplies
Nomenclature Identification No. Qty
Wire, safety C013 AR
Spares
Table 7 Spares
Nomenclature
No Spares
Safety Conditions
No Safety Condition
Procedure
1 Connect the connector of the RBCA electrical checker (AJ-11-00) to the A507J2 receptacle (2, Figure
1).
2 Make sure that the red light of the "Manual Device" comes on.
3 Cut and remove the wire from the two screws (5). Discard the wire.
4 Remove the two screws (5) that attach the cover (4) and the seal (3) to the rotor brake caliper (1).
5 To re-activate the rotor brake caliper (1), use an applicable wrench and rotate counterclockwise the
manual resetting assy (6).
6 Make sure that the red light of the "Manual Device" goes off and the green light comes on.
7 Put the seal (3) and the cover (4) in the correct position on the rotor brake caliper (1).
8 Install the two screws (5) that attach the cover (4) to the rotor brake caliper (1).
9 Torque the two screws (5) to 0.60 thru 0.70 N m (5.31 thru 6.19 lbf in) with the Torque wrench
(ZZ-50-04) .
10 Safety in pairs the two screws (5) with the Wire (C013) .
2 of 6 18/03/2020 20:29
AW169 IETP 14th Issue - Unmaintained Copy https://leonardo.agustawestland.com/amerigo/ietp/printDocument
1 Remove all the tools and the other items from the work area. Make sure that the work area is clean.
3 of 6 18/03/2020 20:29
AW169 IETP 14th Issue - Unmaintained Copy https://leonardo.agustawestland.com/amerigo/ietp/printDocument
4 of 6 18/03/2020 20:29
AW169 IETP 14th Issue - Unmaintained Copy https://leonardo.agustawestland.com/amerigo/ietp/printDocument
5 of 6 18/03/2020 20:29
AW169 IETP 14th Issue - Unmaintained Copy https://leonardo.agustawestland.com/amerigo/ietp/printDocument
6 of 6 18/03/2020 20:29