Professional Documents
Culture Documents
MP HALL - Speci-F
MP HALL - Speci-F
F.1 Materials
Timber shall be straight, sound, bright, of matured growth, well conditioned,
properly seasoned, clean swan, square edged, free from rot, and incipient
decay, shakes, splits, wanes, large loose or dead knots and shall comply with
BS 7359. Soft spots, stains or bright sap wood or other defects and blemishes
will be allowed only if and to the extent to which the Engineer considers that
the timber is rendered unsuitable for the purpose for which it is to be used.
All timber for grounds, hand rails, frames and doors shall be Kiln dry Red
Meranti/Mahogany as indicated in the drawings with a minimum density of
700 kg/m3 and shall have a moisture content limit of 10%. All exposed timber
shall be selected to match in colour and grain and to the approval of the
Engineer. Softwood shall have a moisture content limit of 12%.
Screws are to comply with BS 1210 and be countersunk wood screws. All
hardwood shall be fixed by using brass screws. Upon exposed surfaces all
screws shall be sunk and pelleted in matching hardwood. Adhesives shall be
based on synthetic resins of the Phenolic and Aminoplastic types, type BR in
accordance with BS 1204 or other approved. For external works WBP
adhesive to BS 1203 shall be used.
F/1
Multipurpose Hall at Manah
F.2 Workmanship
Joinery workmanship shall comply with BS 1186 Part 2 and shall be worked in
accordance with details drawings and finished to a smooth wrought face (not
machine planed only) with all arises pencil rounded. All timber shall be cut to
size and shape, properly jointed and put together including framing, gluing,
dowelling, screwing and mortising.
Where joints are not specifically indicated they are to be the same as joints for
similar positions. None of the joinery shall be delivered until it is required for
fixing in the building. Joinery that does not require to be built in as the work
proceeds is not to be brought to the site until the building is enclosed.
Site measurements for joinery shall be taken from the site and not from the
drawings except where the work is specified to be built-in with adequate
tolerance.
Defects such as shrinkage or any other defect occurring in the work either
during the course of works or the period of maintenance shall be replaced and
made good to the Engineer's approval, at the Contractor's expenses. Finish to
joinery to be varnished or painted shall be clean by rubbing down by hand
with fine glasspaper. All joinery shall be adequately protected from damage
during the course of the works and on completion shall be to the Engineer's
satisfaction. Hardwood shall be rubbed down using flour paper between
finishing coats to achieve and even, smooth finish with no raised grains.
F.3 Doors
The door types shall be as shown on the Door Schedule. All timber for doors
shall comply in all respects with the quality specified previously for joinery
but, in addition, shall be kiln dried with a moisture content of not more than
10%. It shall be free from all knots except sound and tight knots not exceeding
10 mm dia., and shall be free from all sapwood. All the fire-rated doors shall
be obtained from the manufacturer approved by the local fire prevention
authorities.
F/2
Multipurpose Hall at Manah
F.3.1 Frames & Architraves
Timber frames, sub-frames, trim beading, Architraves & plinth blocks
and similar work shall be made to the sizes and profiles as shown in the
drawings and shall conform to the BSCP 151 Part 1. All measurements
shall be physically checked at site. The scantlings shall be accurately
planed and finished smooth to hold full dimensions shown in the
drawings. After finishing, the rebates, roundings and mouldings shall
be made before they are framed. No patching or plugging of any kind
shall be permitted. A sample of the frame shall be prepared and
submitted to the Engineer for approval prior to commencement of bulk
manufacture. Approved size/profile plinth blocks shall be provided for
architraves whether or not separately indicated in the drawings.
The timber framework shall be put together with brass screws and the
frames and sub-frames in contact with walls shall be treated with
approved anti-termite material before fixing. Frames shall be with dove
tail joints & fixed with brass screws. The frames shall be fixed to walls
with approved quick setting highly expandable polyurethane
prepolymen (density not less than 25 kg/m 3 and tensile strength at 20
C after 7 days not less than 9 N/cm 2) based foam to the approval of
Engineer. Frames shall be fixed only after rendering, curing, first coat
of painting and floor tiling/skirting works are completed. Frames shall
be shop primed & painted/polished. The final touch-up shall be carried
out at Site after fixing in position.
The polished door shutters shall have 4 mm thick veneered MDF cover
to both sides to receive finish as specified. The shutters for wet areas
such as toilets shall have 4 mm thick veneered moisture resistant MDF.
The Veneer shall be pressed in an approved multidirectional layout.
The shutters shall have cores of solid patterns of an approved type.
Samples of each type of door shall be submitted to the Engineer for
approval. Contractor shall not commence bulk manufacturing of doors
until a complete door panel with all fixtures is fixed at Site as a sample
for approval.
F/3
Multipurpose Hall at Manah
Stiles, top and bottom rails for shutters shall be of Meranti wood of
minimum 100 mm width. Both stiles are to be widened by 55mm
giving a total minimum width of 155 mm for a length of at least 750
mm in the centre of the stiles for lock rails. The shutters shall have
hollow cylindrical cores boards of approved type. All door shutters
shall have a minimum 10 mm thick edging strip similar to
frame/architraves finish. The same shall be twice tongued and glued all
round unless otherwise detailed or specified.
F.4 Ironmongery
Architectural ironmongery shall facilitate building use and maintenance,
prevent unauthorized access and (if required) egress, allow escape from,
protect against an inhibit spread of fire, smoke and other hazards, protect
doors and other surfaces and create desired aesthetic effect.
The Contractor shall not fix ironmongery until background finishes are
complete. Ironmongery previously fixed shall be removed before any finishing
process. Ironmongery for fire rated doors shall be of types, sizes and designs,
which shall not reduce the rating of the door assembly below the specified
level. This shall conform to BS 5388 or DIN 18082 and shall be as approved
by the Royal Oman Police.
F/4
Multipurpose Hall at Manah
Regardless of other provisions, materials shall meet fire safety requirements
and not be subject to bimetallic corrosion with background materials or other
ironmongery. Each item's design and finish shall reflect the nature and
quality of the project. Every finished surface of one material, whether
extruded, rolled, cast or stamped, shall match exactly in colour and texture
and all items on any one visible door face shall be finished to an identical
appearance.
F.4.1 Hinges
Hinges shall be polished & lacquered brass steel ball bearing butt
hinges of 102 76 3 mm /102 102 3mm (CE certified grade 13).
Class of the hinge must be factory engraved/ stamped on each hinge.
Sash lock case will have cylinder to latch function. The lock cases shall
be supplied with polished & lacquered brass striking boxes. The latches
shall be fully reversible without removing the lock case. The lock cases
should have undergone the following tests.
The heavy duty Euro profile cylinders shall be with 5 special plug pins,
open profile and drill & pick resistant. The cylinders shall be in brass
finish and lengths shall be as indicated in the schedule or as per actual
Site requirements. The profile/shape of thumb turn shall be as per
approval. Contractor shall supply minimum 10 cylinders of each type
as spare for future maintenance at no additional cost. Each cylinder
shall be supplied with 3 nos. brass keys unless otherwise indicated. The
key Authorization card shall be supplied in a sealed envelope.
The plates shall have round formed edges. 150mm high kick plates in
polished & lacquered brass shall be minimum 1.5mm thick and shall
extend to the full door leaf width less deductions for any door stops or
rebated edges on the appropriate faces and further deduction of 5mm
from each end of the plate for clearance. The Contractor shall check
dimensions on site against doors before ordering.
a) Closing speed fully adjustable between two and thirty seconds (if
delayed closing is specified the door, when opened to 90 degrees
or beyond, shall stand motionless for a period adjustable upto 60
seconds, before starting to close).
Overhead closers with non projecting track and sliding arm wind-
through adjustable for door sizes 1-4 shall be to BS EN1154. The door
closers must have been certified in accordance with BS 476: Part 22:
1987. The door closers shall have slim line cover, rectilinear & solid
extruded body finished identically to other items on the door, suitable
rustproof track and arm, fully concealed fixings and adjustable back
check as standard to cushion the opening cycle, which helps to prevent
damage to the surrounding walls or door furniture. The door closers
shall be suitable for only one fixing position established by template to
minimize potential for incorrect fitting. The door closers must have
been tested for 2 million cycles. Closers to fire/smoke control doors,
escape route doors, external doors and doors opening through more
than 90 degrees shall be to BS 6459 Class C. If both leaves of a pair of
doors have closers and one must close first, due to rebated styled, etc.,
provide suitable selectors, which will not obstruct other door furniture.
Floor springs shall be of one type suitable for single or double action
wood or metal doors by use of compatible fittings with concealed fixing
cover plates matching other finishes, cast-iron mechanism body and
outer box allowing mechanical adjustment vertically, longitudinally
and transversely after installation.
The floor springs shall be suitable for minimum 150 kg shutter weight,
1000mm wide door shutter, hold open at 90 0, closing speed
adjustment, latch adjustment, temperature stabilized fluid with thermo
constant valve to overcome temperature variance.
The stop seals consisting of 5.5 5.5mm carrier made from high grade heat
treated aluminium alloy matching with door finishes and 7mm dia highly
flexible silicone rubber tubler seal with excellent recovery properties will be
rebated into the jambs and head of the frames. The system shall meet the
requirements of Class 1 & 3 of BS 7386 : 1990 and to the approval of the
Engineer.
The strip seals shall be made of fine, dense, UV stabilized black nylon
filaments locked into a galvanized steel spine and shall be fixed into an
aluminium carrier in a concealed manner. Any wooden door exposed to rain
shall have proprietary threshold seals and stop seals. The threshold seal
consisting of weatherboard, threshold and adjustable contract strip all
complete with elastomeric neoprene insert blade and compression seal etc.
shall be to the approval of the Engineer.
2 years guarantee from the date of handing over of the project will be
provided jointly by the Supplier and the Contractor.
The multi-layer parquet with oak surface layer should have a fire classification
of Cfl-S1 according to EN 14342.
To the front face of stage will be protected with wooden edge profile for fixing
strip light as indicated in drawing with all details or instructed by engineer.
Watertight glued HDF base the main component of the profile is wood.
The HDF base is resistant to dampness, which ensures your profile
remains in perfect condition.
Expansion profile: The expansion profile is used to join two floors in:
doorways, door openings, L-shaped rooms or rooms where the floor is
greater in distance than 12 m in length or width.
Edge profile: The edge profile is used to finish the edge of a floor against a
vertical surface such as sliding doors, low open windows, a slightly higher
doorstep or tiled floor.
F/10
Multipurpose Hall at Manah
The gypsum plaster board shall fixed using glue or screws. If screws are used
then they must not penetrate the interior of the system. Each panel shall be
provided with a retractable spring tensioned seal at the top and bottom. The
seals shall be pressed against the underside of the aluminium track at the top
and against the finished floor at the bottom, by manually operating an
internal spindle mechanism. The seals shall be aluminium based and
designed to overcome small deviations in the floor and to achieve high
acoustic values & to ensure a rigid closure. The aluminium nose and counter
profiles to ensure tight closure between the panels by magnetic strips and
rubber seals. These vertical profiles can be exposed, to give protection to the
edges of the panel, or can be inlaid (recessed) so they are not visible when the
partition is closed.
The closing panel of the wall to be telescopic adjusting panel. This panel to
have an internal telescopic section (the suitcase) on one side. This section to
be built in the same way and of the same materials as the panel. It shall be
operated, together with the top and bottom seals, by an internal three-way
spindle mechanism. The maximum achievable stroke shall be approx. 120
mm, with adjustable pressure. Every panel to be suspended by one, or two,
trolleys which will run in an aluminium ceiling track. These maintenance free
trolleys shall be of multiple ball bearing type. The trolleys shall be connected
to the panel by means of a steel trolley bolt. All panels shall have facility to be
adjusted for height without opening the ceiling, or the panel. In case of
surface damage, the face panels shall allow the replacement without removing
the panel from the track.
Minimum one Single wicket door panel shall be provided at the location
approved by the Engineer. The same shall be constructed with a steel frame.
The frame legs (jambs) shall incorporate retractable seals for complete and
tight closure to the floor. The seals in the frame legs, and at the top of the
panel, shall be manually operated by an internal mechanism. This mechanism
also shall lock the door during the movement of panels. The bottom seal of the
door leaf shall be automatically activated and allow adjustment to the correct
stroke. The track shall be fixed to the structure with the help of M10 threaded
rods as indicated in the drawings. Contractor shall be responsible for
providing complete supporting structure as indicated in the drawings in
coordination with the partition manufacturer to ensure that track is rigid and
does not sway. All necessary triangular sideways shall be erected. Similarly,
the false ceiling work also will be coordinated with the track to have neatly
finished junctions.
The Contractor will submit a detailed coordinated shop drawing for approval
prior to commencement of the fabrication. 2 years guarantee against
manufacturing defects shall be provided from the date of handing over of the
project.
Finishes
Face finish shall be factory applied reinforced vinyl fabric with woven backing,
fully washable, stain 1-12 ASTM-d 1308, resistant, fire rating CLASS 1-BS 476
PART 7 weighing not less than 15 oz. per lineal yard [465 g/m]. Color shall be
selected from manufacturer’s standard color selector.
F/11
Multipurpose Hall at Manah
Ironmongery Schedule for Multipurpose Hall at MANAH
F/12
Multipurpose Hall at Manah
52 9 mm polished and lacquered brass finish Concealed decorative
2 No’s
Escutcheon
25 mm dia 380 mm Polished and lacquered brass finish Decorative Pull
2 No’s
Handle Bolt through fixing
400 75 1.5 mm Push Plate in Polished and lacquered brass finish 2 No’s
19 225 mm polished and lacquered brass finish Lever Action Flush Bolt 2 No’s
Polished and lacquered brass finish Dust Excluding Sprung Socket 1 No.
42 52 38 mm polished and lacquered brass floor mounted Door Stop 2 No’s
Door Type (D4) - 44 mm – Entrance Foyer to Lobby
Floor spring unit with polished and lacquered brass top plate with 90º Hold
2 No’s
Open
165 93 15 mm Oval Cylinder heavy-duty powder coated Dead Lock Case
1 No.
with 60 mm backset
Rebating Component 1 No.
70 mm Oval drill and pick resistant 6 Pin Double Cylinder 1 No.
52 9 mm polished and lacquered brass finish Concealed decorative
2 No’s
Escutcheon
25 mm dia 380 mm Polished and lacquered brass finish Decorative Pull
2 No’s
Handle Bolt through fixing
400 75 1.5 mm Push Plate in Polished and lacquered brass finish 2 No’s
19 225 mm polished and lacquered brass finish Lever Action Flush Bolt 2 No’s
Polished and lacquered brass finish Dust Excluding Sprung Socket 1 No.
42 52 38 mm polished and lacquered brass floor mounted Door Stop 2 No’s
300 100 1.5 mm thick polished and lacquered brass finish name plate
1 No.
including engraving of names in Arabic and English
Door Type (D4A) - 44 mm – Lobby to Corridor
102 76 3 mm Polished and lacquered brass finish Ball Bearing Butt Hinges 2 Pair’s
165 93 15 mm Oval Cylinder heavy-duty powder coated Sash Lock Case
1 No.
with 60 mm backset
70 mm Oval drill and pick resistant 6 Pin Double Cylinder 1 No.
Sprung lever handle on 235 42 9 mm decorative polished and lacquered
1 Pair
brass finish cylinder hole back/face plate
Polished and lacquered brass finish non projecting track & sliding arm O/H
1 No.
Hydraulic Door Closer Power 1 – 4
76 mm polished and lacquered brass wall mounted Door Stop 1 No.
300 100 1.5 mm thick polished and lacquered brass finish name plate
1 No.
including engraving of names in Arabic and English
F/13
Multipurpose Hall at Manah
Door Type (D5) - 44 mm – VIP Lounge & Pantry
102 76 3 mm Polished and lacquered brass finish Ball Bearing Butt Hinges 2 Pair’s
165 93 15 mm Oval Cylinder heavy-duty powder coated Sash Lock Case
1 No.
with 60 mm backset
70 mm Oval drill and pick resistant 6 Pin Double Cylinder 1 No.
Sprung lever handle on 235 42 9 mm decorative polished and lacquered
1 Pair
brass finish cylinder hole back/face plate
Polished and lacquered brass finish non projecting track & sliding arm O/H
1 No.
Hydraulic Door Closer Power 1 – 4
42 52 38 mm polished and lacquered brass floor mounted Door Stop 1 No.
300 100 1.5 mm thick polished and lacquered brass finish name plate
1 No.
including engraving of names in Arabic and English
Door Type (D6) - 44 mm – VIP Lounge to toilet lobby
102 76 3 mm Polished and lacquered brass finish Ball Bearing Butt Hinges 2 Pair’s
25 mm dia 380 mm Polished and lacquered brass finish Decorative Pull
1 No.
Handle Bolt through fixing
400 75 1.5 mm Push Plate in Polished and lacquered brass finish 1 No.
Polished and lacquered brass finish non projecting track & sliding arm O/H
1 No.
Hydraulic Door Closer Power 1 – 4
42 52 38 mm polished and lacquered brass floor mounted Door Stop 1 No.
300 100 1.5 mm thick polished and lacquered brass finish name plate
1 No.
including engraving of names in Arabic and English
150 150 1.5 mm thick polished and lacquered brass finish Graphic sign 1 No
Door Type (D6) - 44 mm – Green Room, Electrical Control Room
and Lobby
102 76 3 mm Polished and lacquered brass finish Ball Bearing Butt Hinges 2 Pair’s
165 93 15 mm Oval Cylinder heavy-duty powder coated Dead Lock Case
1 No.
with 60 mm backset
70 mm Oval drill and pick resistant 6 Pin double cylinder 1 No.
52 9 mm polished and lacquered brass finish Concealed decorative
2 No’s
Escutcheon
25 mm dia 380 mm Polished and lacquered brass finish Decorative Pull
1 No.
Handle Bolt through fixing
400 75 1.5 mm Push Plate in Polished and lacquered brass finish 1 No.
Polished and lacquered brass finish non projecting track & sliding arm O/H
1 No.
Hydraulic Door Closer Power 1 – 4
42 52 38 mm polished and lacquered brass floor mounted Door Stop 1 No.
300 100 1.5 mm thick polished and lacquered brass finish name plate
1 No.
including engraving of names in Arabic and English
F/14
Multipurpose Hall at Manah
Door Type (D6) - 44 mm – Oman TV Room
102 76 3 mm Polished and lacquered brass finish Ball Bearing Butt Hinges 2 Pair’s
165 93 15 mm Oval Cylinder heavy-duty powder coated Sash Lock Case
1 No.
with 60 mm backset
70 mm Oval drill and pick resistant 6 Pin Double Cylinder 1 No.
Sprung lever handle on 235 42 9 mm decorative polished and lacquered
1 Pair
brass finish cylinder hole back/face plate
42 52 38 mm polished and lacquered brass floor mounted Door Stop 1 No.
300 100 1.5 mm thick polished and lacquered brass finish name plate
1 No.
including engraving of names in Arabic and English
Door Type (D6) - 44 mm – Handicapped Toilet
102 76 3 mm Polished and lacquered brass finish Ball Bearing Butt Hinges 2 Pair’s
165 93 15 mm Oval Cylinder heavy-duty powder coated Bathroom Lock
1 No.
Case with 60 mm backset
F/15
F/16