Professional Documents
Culture Documents
Technical Spec 400kV Disconnectors - EDF-10.01.2024
Technical Spec 400kV Disconnectors - EDF-10.01.2024
Document Control
SIGN OFF
Name (Role) Signature Date
DOCUMENT CONTROL
Document
DMS document refer added here
Number
Schedule of Requirements for Outdoor Disconnector for Solar Farms, Wind Farms, and
Document Title
Battery Energy Storage Systems
Rev. Date Description Prepared Checked Approved
[dd mmm yyyy]
1 INTENT OF SPECIFICATION
This specification is intended to cover the design, manufacture, assembly, testing at manufacturer's works, supply
& delivery, properly packed for transport to site of 400 KV disconnectors, complete with all materials and
accessories for efficient and trouble-free operation in a manner acceptable to Owner.
In the event of any discrepancy with listed documents, the stipulation of this specification shall govern.
The specification shall be read and construed in conjunction with other sections of bidding document.
2 SCOPE OF WORK
2.1 Scope of Supply
Type, rating, connections, etc. of the equipment shall be as detailed in the drawings and annexures. The
equipment shall be furnished in strict compliance with the same.
2.1.1 Each disconnector shall be furnished complete with:
a) Fittings and accessories.
b) Auxiliary equipment.
2.1.2 Spares
2.1.3 All relevant drawings, data and instruction manuals.
3 GENERAL REQUIREMENTS
3.1 Codes and Standards
Equipment is to be NG type registered in line with the requirements of:
General Information
3.2.14 SHORT TIME WITHSTAND CURRENT AND DURATION kA & sec. 63,1
3.8.13
4 TECHNICAL COMPLIANCE
The attached appendix ‘A’ technical compliance check sheet is to be provided as part of the clarified quotation.
Yes No
Yes No
Yes No
Yes (____________) No
Technical leaflets on equipment explaining construction features, principle of operation, special features etc.
Assembly drawing for erection at site with part numbers and schedule of materials.
Any other relevant drawing or data necessary for satisfactory installation, operation and maintenance.
The manual shall clearly indicate method of installation, check ups and tests to be carried out before
commissioning of the equipment.
3. Relay, Power Contractor and Switch Fuse for Electrical Control 1 Set
Circuit
5. Bearing 2 Sets
6. Hinge Pin 2
7. Terminal Pad 2
11. Motor 2
8 LIST OF SUPPLIERS
9 SCHEDULE A
TECHNICAL DETAILS
NO. DESCRIPTION UNIT VALUE
5 NUMBER OF POLES
6 DESIGN TYPE (REP, RCP, VERT, REPTAN, RCPTAN. TAN=TANDEM)
7 DISCONNECTOR RATINGS DETAILS
7.01 Rated Design Voltage (eg 420kV) kV
7.02 Rated Design Current A
7.03 Rated Short-time Withstand Current kA
7.04 Duration of Rated Short-time Withstand Current seconds
7.05 Rated Peak Withstand Current kA
7.06 Bus Transfer Duty to IEC 62271-102 Yes/No
7.07 Bus-transfer Voltage V
7.08 Bus-transfer Current A
7.09 Capacitive Current Switching Capability A
7.10 Inductive Current Switching Capability A
7.11 Load Make or Break Capability Yes/No
15 INSULATION
15.01 Manufacturer of Support Insulation
15.02 Support Insulation Type Reference
15.03 Manufacturer of Drive Insulation
15.04 Drive Insulation Type Reference
15.05 Support insulator deflection under 70% load mm
GENERAL DETAILS
1 MANUFACTURER
2 MANUFACTURER'S TYPE / MODEL
3 YEAR PRODUCTION COMMENCED (month/year)
4 DRAWINGS
4.01 Three Phase Arrangement Drawing No. / Rev
4.02 Control Schematic Drawing No. / Rev
4.03 Base Fixing (Foundation) Drawing No. / Rev
4.04 Base Loading (Foundation) Drawing No. / Rev
TECHNICAL DETAILS
NO. DESCRIPTION UNIT VALUE
5 NUMBER OF POLES
6 DESIGN TYPE
7 EARTH SWITCH MOUNTED WITH (PART OF) Yes/No
DISCONNECTOR
GENERAL DETAILS
13.02 Watts
13.03 Motor operating time Close - seconds
13.04 Open - seconds
13.05 Motor protection operating time (stalled) seconds
14 METHOD OF OPERATION - Manual (Hand)
14.01 Maximum torque required to operate Close - N
14.02 Open - N
15 METHOD OF OPERATION - OTHER
15.01 Specify and provide relevant data
17 INSULATION
17.01 Manufacturer of Support Insulation
17.02 Support Insulation Type Reference
17.03 Support insulator deflection under 70% load mm
GENERAL DETAILS
19.03 Fc N
10 SCHEDULE B
(1) - Supplier to confirm item tested is identical to the item offered for type registration. Differences should be
identified in the non-conformance schedule
(2) - Suppler to confirm item has been tested in full compliance with the reference test specification. Differences
should be identified in the non-conformance schedule
(3) - Supplier to confirm tests have been independently witnessed
Product Type
(1) - Supplier to confirm item tested is identical to the item offered for type registration. Differences should be identified in
the non-conformance schedule
(2) - Suppler to confirm item has been tested in full compliance with the reference test specification. Differences should be
identified in the non-conformance schedule
(3) - Supplier to confirm tests have been independently witnessed
Product Type
(1) - Supplier to confirm item tested is identical to the item offered for type registration. Differences
should be identified in the non-conformance schedule
(2) - Suppler to confirm item has been tested in full compliance with the reference test specification.
Differences should be identified in the non-conformance schedule
(3) - Supplier to confirm tests have been independently witnessed
Product Type
IEC 62271-
Severe Ice Conditions
102
IEC 62271-
Operation at Temperature Limits
102