Professional Documents
Culture Documents
Fans and Blowers For Solid Fuel Heating Systems Catalog en
Fans and Blowers For Solid Fuel Heating Systems Catalog en
Environmentally friendly, cost effective and constantly renewable – Particularly efficient with EC and condensing technology
heating with biomass offers many advantages compared to burning
fossil fuels. However, wood pellet and wood chip heating systems In solid-fuel heating systems, a distinction is made between traditio-
have very special requirements: the air flow required for different nal conventional heating and modern condensing technology. Whe-
functions must be provided economically in each operating state and reas with conventional heating most of the waste heat can get into
regardless of the heating power. There is also limited space in stoves. the open air via the chimney, condensing technology makes as much
The fans required for this must be robust and compact. use of this energy as possible. Heat from the water vapor produced
when the wood pellets or wood chips burn is recovered and fed back
ebm-papst offers the right fans to overcome these challenges. The into the heating system. This increases the efficiency and reduces
fans for the combustion air supply, exhaust gas removal and distribu- the heating costs.
tion of hot air in the installation area are tailored to different power
classes and equipped with fan impellers optimized for biomass appli- ebm-papst offers a wide range of AC and EC fans for traditional con-
cations. Due to their compact design, they are robust, durable and ventional heating. In modern condensing technology, using more
require hardly any space. This facilitates having the optimum size, efficient EC fans is particularly worthwhile, as they can be optimally
performance and cost-effectiveness in any application. adapted to the relevant operating point using their variable speed.
2
Fans and blowers for solid fuel heating systems
Contents
Page Page
Information
Was engineering a better life für uns bedeutet.
Convection heat
Convection heat centrifugal fans 54
Convection heat tangential fans 68
Additional information
Additional shaft seal 88
Electrical connections 89
Technical parameters & scope 94
Fans and blowers for solid fuel heating systems · Edition 2022-06 3
What Engineering
a better life
means to us.
4
Who we are. What drives us.
With over 20,000 different products, ebm-papst offers the right But our consistent pursuit of efficiency and progress has even deeper
solution for just about any challenge. As the logical next stage roots. After all, there is something that excites us even more than our
in the development of our highly-efficient GreenTech EC tech- market position. It is the deep awareness that, with our solutions, like
nology, we believe that industrial digitization offers the greatest the VSW0210, we are making the lives of many people around the
future prospects for our customers. With GreenIntelligence, globe more pleasant, safer and thus better. Therefore, the central
we already represent intelligently interconnected complete driving force in all our thoughts and actions is Engineering a better
solutions that are unrivaled worldwide. life. It is the reason why it is worthwhile for us to get up every day
and do our best.
Because we are always committed to making each of our inno-
vative hardware and software solutions more powerful, com- More about this under ebmpapst.com/betterlife
pact, efficient and sustainable than its predecessor, we have
evolved over the years into the global technology leader for
ventilation and drive technology.
1. Technological edge.
With our EC technology and GreenIntelligence,
we combine the highest energy efficiency with
4. The ebm-papst spirit of invention.
Over 800 engineers and technicians will develop a solution
that precisely fits your needs.
the advantages of IoT and digital networking.
6.
with energy-saving products, environ- Our standard of quality.
mentallyfriendly processes and Our quality management is uncompromising, at every
through social engagement. step and in every process.
3. System expertise.
As experts in advanced motor technology,
electronics and aerodynamics, we provide perfect
system solutions from a single source.
Fans and blowers for solid fuel heating systems · Edition 2022-06 5
Fans and blowers for solid fuel heating systems
6
Induced draft fan
Product overview
Dimensions in mm Heat output range Type Part number Page
AC:
EC:
Fans and blowers for solid fuel heating systems · Edition 2022-06 7
Fans for solid fuel heating systems
Induced draft fans are used in biomass stoves ebm-papst offers induced draft fans with and without fan housing, with various bla-
in living rooms and biomass heating systems in des and, depending on the air flow requirement, in different fan impeller diameters.
cellars. There, they extract the hot exhaust ga- They are also available in versions with AC and EC motors. The fan impellers are cur-
ses that form when wood pellets, wood chips ved backwards. In the EC version, the induced draft fans are particularly economical
Induced draft fan
or firewood are burned and send them to the thanks to a highly efficient motor and thanks to their controllability. By adjusting the
chimney. They have to withstand high tem- speed, the suction power can always be optimally adjusted to the relevant heat load.
peratures. For this reason, the motor for the- At partial load, this also reduces the fan's power requirement at the same time.
se blowers is located outside the fan housing.
Condensing units have an additional advanta- For special application conditions, the fans can also be equipped with a special shaft
ge here: as their exhaust gas temperatures are seal that is specifically adapted to the flow medium. Further information can be
much lower, they are much more efficient. found on page 88.
in wg
Pa
Pa
A 2
1600
D
6
300 H
B 2
B 2
5
1200
1
A
F
4
200
G
A 800
A 1
D B 1
3
K
B 1 C I
C F E 2
2
100
400 H
E G 1
G 2 J 1
1
J 2
E 1
P fs
qv 50 100 150 200 250 m³/h qv 200 400 600 800 1000 m³/h
8 Fans and blowers for solid fuel heating systems · Edition 2022-06
Induced draft fan heat output range
Overview
4 – 12kW A R2E140CD76**
5 – 15kW B VBS0152XQFFS
5 – 15kW C VCS0152XQFFS
10 – 24kW A R3G140AG03**
10 – 24kW A R1G150AA63**
10 – 24kW C G3G150DA03**
10 – 24kW D R3G160AE01**
Fans and blowers for solid fuel heating systems · Edition 2022-06 9
AC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 140
in H2O
cfm
pfs
qV m3/h
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
10 Fans and blowers for solid fuel heating systems · Edition 2022-06
R2E140CD76**
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB °C kg
Type Part number Fan type
Cable
R2E140CD7601 design ❶ 215 2650 28 0.14
❷ 215 2635 28 0.14
VSW0140X2MCS M2E 068-BF A ❸ 215 2660 28 0.13
0.68/400 -25...+60 1.6
Subject to changes.
87 53.5±1.5 76 25°
42
4x9
0°
Ø165.3
Ø140
Ø116
4xØ4.5
450±20
Ø1
58
123456 Wieland
Wieland 93.031.3253.0
93.032.3353.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 11
AC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 150
in H2O
3
■ Additional shaft seal see page 88
80
0,3
60
0,2
40
0,1
20
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
12 Fans and blowers for solid fuel heating systems · Edition 2022-06
R2E150AO91** / R2E150AN91**
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB °C kg
Type Part number Fan type
Cable
R2E150AO9101 design
VSW0150X2MCS ❶ 200 2400 32 0.15
❷ 200 2410 31 0.14
R2E150AO9105 Plug M2E 068-BF A ❸ 200 2435 31 0.14
1.0/400 -25...+55 1.7
design
❹ 200 2485 30 0.13
without
VSW0150X2MCS R2E150AN9101 motor pro-
tection hood
Subject to changes.
3 N black
0°
4 GND black
Ø165.3
Ø152
Ø116
5 OUT white
6 VCC red
4xØ4.5
450±20
Ø1
58
4x9
15
Ø
0˚
Ø165,3
Ø152
4xØ4,5
450±20
1 2 3456 Wieland
Wieland 93.031.3253.0
93.032.3353.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 13
AC centrifugal blowers (exhaust air)
for solid fuel heating systems, single inlet, Ø 150
■ Type of protection: IP 44
■ Insulation class: "F"
■ Mounting position: any
from page 86 Scroll dimensions ■ Condensate discharges: none, open rotor
page 93 Electrical connections A1), D)
■ Mode of operation:
More at www.ebmpapst.com Continuous operation (S1)
■ Bearings: Maintenance-free ball bearings
■ Max. exhaust gas temperature:
Continuous operation 250°C
■ Motor protection: TOP wired internally
■ Touch current: < 0.75mA acc. to IEC 60990
in H2O
Pa
■ Protection class: I
240
A Standards and approvals
■ Standards: EN 60335-1, CE;
200 UKCA on request
0,8
4
■ Approvals:
UL, CSA, CCC, EAC are applied for
160 Optional
0,6
120
0,4
80
2
0,2
40
1
0 10 20 30 40 50 60 70 80 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and 1Heat output range
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
14 Fans and blowers for solid fuel heating systems · Edition 2022-06
G2E150DO91** / G2E150DN91**
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB °C kg
Type Part number Fan type
Cable
G2E150DO9101 -25...+50 2.3
design
VPW0150X2MCS
❶ 145 2480 30 0.14
Plug ❷ 145 2505 30 0.13
G2E150DO9105 design
M2E 068-BF A ❸ 145 2560 29 0.13
1.0/400 -25...+50 2.3
❹ 145 2620 28 0.12
Cable design
VPW0150X2MCS G2E150DN9101 without pro- -25...+70 2.3
tection hood
137
149 8.6 Ø80 P X Y Connection
P9 P11
32 1 -24.7 -100.6
P10 P12 No. Function Color
2 -20.8 -87.1 1 L blue
3 -34.3 -97.8 2 PE green/yellow
118.2
P4 9 120.3 49.4
P7
10 108.5 41.9
P8
450±20
52
11 114.9 57.8
85±10
12 103.1 50.3
6
85 94.2
137
149 8.6 Ø80
P9 P11 132
32 P10 P12
118.2
62
Ø116
Ø92
P2
P1
P6
P3 P5
90.4
1 P4
2 P7
3 P8
4
5
6 52
85 94.2
Fans and blowers for solid fuel heating systems · Edition 2022-06 15
AC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 150
in H2O
140 ■ Approvals:
UL, CSA, CCC, EAC are applied for
120 3
Optional
■ Additional shaft seal see page 88
100
0,4
80
60
0,2
40
20
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
16 Fans and blowers for solid fuel heating systems · Edition 2022-06
R2E150AP82** / R2E150AK82**
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB °C kg
Type Part number Fan type
Cable
R2E150AP8201 -25...+60 1.8
design
VSW0150X2MES ❶ 220 2750 44 0.27
❷ 220 2760 44 0.27
R2E150AP8205 Plug M2E 068-CF A ❸ 220 2770 43 0.26
1.0/400
-25...+60 1.8
design
❹ 220 2795 41 0.26
without
VSW0150X2MES R2E150AK8201 motor pro- -25...+70 2.0
tection hood
Subject to changes.
3 N black
0°
4 GND black
Ø165.3
Ø148
Ø119
5 OUT white
6 VCC red
4xØ4.5
450±20
Ø1
58
4x9
15
Ø
0˚
Ø165,3
Ø148
4xØ4,5
450±20
1 2 3456 Wieland
Wieland 93.031.3253.0
93.032.3353.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 17
AC centrifugal fans (exhaust air)
for solid fuel heating systems, special designs, Ø 150/160
in H2O
■ Standard:
A
Speed monitoring via Hall IC
■ Cable exit: variable
B
■ Protection class: I
Standards and approvals
■ Standards: EN 60335-1, CE
■ Approvals:
UL, CSA, CCC, EAC are applied for
Optional
■ Additional shaft seal see page 88
cfm
pfs
qV m3/h
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
18 Fans and blowers for solid fuel heating systems · Edition 2022-06
R2E160BG34** / R2E150AL06**
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB db(A) °C kg
Type Part number Fan type
without
R2E160BG3401 motor pro-
tection hood
❶ 285 2780 57 0.26
VSW0160X2MGS M2E 068-DF A ❷ 285 2830 48 0.22
1.5/400 64 -25...+90 3.8
with
R2E160BG3405 motor pro-
tection hood
without
R2E150AL0601 motor pro-
tection hood
❶ 460 2785 78 0.35
VSC0150X2NGS M2E 074-DF B ❷ 460 2840 65 0.30
3.0/400 67 -25...+85 4.0
with
R2E150AL0605 motor pro-
tection hood
g 132 144
h 109 146
450+ 20
4xØ9
h ±1
Øg
Fans and blowers for solid fuel heating systems · Edition 2022-06 19
AC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 152
in H2O
cfm
pfs
qV m3/h
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
20 Fans and blowers for solid fuel heating systems · Edition 2022-06
VBS0152XQFFS
Weight
Nominal voltage 230VAC, 50Hz m3/h rpm W A °C kg
Type Part number
Subject to changes. A measured without ebm-papst scroll housing. B measured with ebm-papst scroll housing.
31.5±1.5
45°
20 45°
30.3±0.4
Ø152+1
Ø4.5
max. 81 Ø158±0.2
Ø165,3±0.5
Fans and blowers for solid fuel heating systems · Edition 2022-06 21
AC centrifugal blowers (exhaust air)
for solid fuel heating systems, single inlet, Ø 152
■ Type of protection: IP 00
■ Insulation class: "H"
■ Mounting position:
from page 86 Scroll dimensions any, except motor overhead
page 93 Electrical connections B) ■ Mode of operation:
More at www.ebmpapst.com Continuous operation (S1)
■ Bearings: Ball bearings / sleeve bearings
■ Max. exhaust gas temperature 250°C
■ Motor protection: TOP wired internally
■ Standard:
Speed monitoring via Hall IC
in H2O
Pa
■ Protection class: I
280
Standards and approvals
■ Standards: EN 60335-1, CE;
1,0
160
0,6
120
0,4
80
2
0,2
40
1
0 10 20 30 40 50 60 70 80 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and 1Heat output range
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
22 Fans and blowers for solid fuel heating systems · Edition 2022-06
VCS0152XQFFS
Air flow
Weight
Nominal voltage 230VAC, 50Hz m3/h rpm W A °C kg
Type Part number
Subject to changes.
90° 2 2 = V out
2
Ø4.5 3 3 = Ground
Ø3.2
149 Ø4.5 max.142.5
Ø3.2 °
136.7±2 32.5
149 max.142.5 x) 2.5°
9 41 20° 49 ( 3 3
136.7±2 10 )
9 41 20° 0.5+1
49
47±0.3(3x
10
0.5+1 47±0.3
106°
Ø80 ±0.4
B B Z
4
116±0.3
Ø9
106° 114
Ø80 ±0.4
B B Z Ø
°
4
116±0.3
122
Ø9
14
62
(214)
Ø1
°
122
62
(214)
51±0.3
22 ±0.3
51±0.3
22 ±0.3
(253.5)
Fans and blowers for solid fuel heating systems · Edition 2022-06 23
AC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 180
in H2O
Optional
3
■ Additional shaft seal see page 88
160
0,6
100
120
2
0,4
80
0,2
40
1
0 20 40 60 80 100 120 140 160 180 200 220 240 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
24 Fans and blowers for solid fuel heating systems · Edition 2022-06
R2E180CV82** / R2E180CG82**
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB °C kg
Type Part number Fan type
Cable
R2E180CV8201 -25...+45 1.7
design
VSW0180X2MES ❶ 420 2500 75 0.34
❷ 420 2490 74 0.33
R2E180CV8205 Plug M2E 068-CF A ❸ 420 2520 72 0.32
2.0/400
-25...+45 1.7
design
❹ 420 2585 67 0.30
without
VSW0180X2MES R2E180CG8201 motor pro- -25...+60 2.3
tection hood
Subject to changes.
Connection
108 54.5±1.5
47. No. Function Color
45 5
Ø1 1 L blue
98
2 PE green/yellow
3 N black
4 GND black
5 OUT white
Ø180
4x90°
Ø210
Ø119
6 VCC red
450±20
4xØ4.5
90±1 54,5±1,5 Ø210
73 45 Ø198±0,2
Ø180
450±20
4xØ4,5
Wieland 1 2 3 4 5 6 Wieland
93.032.3353.0 93.031.3253.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 25
AC centrifugal blowers (exhaust air)
for solid fuel heating systems, single inlet, Ø 180
■ Type of protection: IP 44
■ Insulation class: "F"
■ Mounting position: any
from page 86 Scroll dimensions ■ Condensate discharges: none, open rotor
page 93 Electrical connections A1), D)
■ Mode of operation:
More at www.ebmpapst.com Continuous operation (S1)
■ Bearings: Maintenance-free ball bearings
■ Max. exhaust gas temperature:
Continuous operation 250°C
■ Motor protection: TOP wired internally
■ Touch current: < 0.75mA acc. to IEC 60990
in H2O
Pa
3
Optional
■ Additional shaft seal see page 88
200
0,8
100
0,4
1
0 20 40 60 80 100 120 140 160 180 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and 1Heat output range
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
26 Fans and blowers for solid fuel heating systems · Edition 2022-06
G2E180CV82** / G2E180GV82**
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB db(A) °C kg
Type Part number Fan type
Cable
G2E180CV8201 design*
VPW0180X2MES
Plug
G2E180CV8205 design
❶ 340 2600 65 0.30 73
❷ 340 2645 60 0.26 70
M2E 068-CF A ❸ 340 2700 55 0.24
1.0/400
64
-25...+60 3.0
❹ 340 2765 48 0.21 62
Cable
G2E180GV8201 design*
VPW0180X2MES
174
Ø100 Connection
a 17 17
50 P9 P11 No. Function Color
P12
P10 1 L blue
A
2 PE green/yellow
3 N black
134.5
4 GND black
P6
5 OUT white
74.5
P5
6 VCC red
Ø119
P7
P8
P2 Detail A P X Y
105
P1
G2E180GV82** 1 -84.9 -88.4
450±20
P3
85±10
2 -75 -78.5
6
P4
101 115.3 66 3 -92 -81.3
4 -82 -71.4
5 16.5 134
174 6 16.5 120
Ø100 7 6.5 134
a 17 17
50 P9 P11 8 6.5 120
P10 P12 9 153 -5
A
10 139 -5
11 153 5
134.5
12 139 5
P6
74.5
P5
Ø119
Dimensions
P7
P8 VPW0180X2MES VPW0180X2MES
G2E180CV82** G2E180GV82**
105
1 P2
2
3
P1 a 186 223
4 P3
5
6 P4 101 115.3 66
Fans and blowers for solid fuel heating systems · Edition 2022-06 27
AC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 210
in H2O
480 ■ Standard:
Speed monitoring via Hall IC
1,8
4 4
■ Approvals:
320 UL, CSA, CCC, EAC are applied for
1,2
280 Optional
■ Additional shaft seal see page 88
1,0
240 3 3
100
200
0,8
160
0,6
120 2 2
0,4
80
0,2
40
1 1
0 50 100 150 200 250 300 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
28 Fans and blowers for solid fuel heating systems · Edition 2022-06
R2E210AA34** / R2E210AB34**
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB °C kg
Type Part number Fan type
without
R2E210AA3401 motor pro- ❶ 520 2500 110 0.49
tection hood
❷ 520 2495 109 0.48
VSW0210X2MGS A ❸ 520 2550 102 0.44
2.0/450 -25...+90 2.9
with
R2E210AA3405 motor pro- ❹ 520 2660 87 0.38
tection hood
M2E 068-DF
without
R2E210AB3401 motor pro- ❶ 600 2400 125 0.56
tection hood
❷ 600 2420 125 0.54
VSW0210X2MGS B ❸ 600 2455 122 0.53
2.5/400 -25...+70 3.1
with
R2E210AB3405 motor pro- ❹ 600 2545 111 0.48
tection hood
4xØ4.5
105 ±1
Ø132 ± 1
Fans and blowers for solid fuel heating systems · Edition 2022-06 29
AC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 250
in H2O
4
■ Cable exit: variable
■ Protection class: I (if customer has provided
A connection for protective earth)
500
2,0
3
UL, CSA, CCC, EAC are applied for
Optional
300 ■ Additional shaft seal see page 88
1,2
200
0,8
100
0,4
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
30 Fans and blowers for solid fuel heating systems · Edition 2022-06
R2E250BE0310
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB °C kg
Type Part number Fan type
Subject to changes.
158 65.6
55.5 Ø290
4
6x6
Ø6 (4x) 0°
1 2 3 4 5 6
Connection
No. Function Color
1 Hall-IC black
2 Hall-IC white
3 Hall-IC red
Ø250
146
4 black + Capacitor
5 – green/yellow
6 – blue
75
Ø2
Fans and blowers for solid fuel heating systems · Edition 2022-06 31
EC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 140
40
1
0 20 40 60 80 100 120 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
32 Fans and blowers for solid fuel heating systems · Edition 2022-06
R3G140AG03**
Air flow
Weight
Speed
Motor
Nominal voltage 1~200-240, 50/60Hz m3/h rpm W A db(A) °C kg
Type Part number Fan type
Cable
R3G140AG0301 design ❶ 220 2650 18 0.15
❷ 220 2635 18 0.15
VSW0140XSLBS M3G 055-AI A ❸ 220 2660 18 0.14
65 -25...+60 1.3
Subject to changes.
4 0-10V/PWM yellow
°
5 GND blue
Ø165.3
Ø116
Ø140
6 Tacho white
4xØ4.5
450±20
Ø1
58
12 3 4 5 6 Wieland
Wieland 93.031.3253.0
93.032.3353.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 33
EC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 150
in H2O
80
0,2
40
1 1
0 25 50 75 100 125 150 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
34 Fans and blowers for solid fuel heating systems · Edition 2022-06
R3G150AA03** / R3G150AC01**
Air flow
Weight
Speed
Motor
Nominal voltage 1~200-240, 50/60Hz m3/h rpm W A °C kg
Type Part number Fan type
Cable
R3G150AA0301 design ❶ 145 2530 16 0.17
❷ 145 2540 16 0.17
VSW0150XSLBS M3G 055-AI A ❸ 145 2600 14 0.16
-25...+60 1.25
Cable
R3G150AC0101 design ❶ 275 2803 29 0.30
❷ 275 2770 30 0.30
VSW0150XSLCS M3G 055-BD B ❸ 275 2796 29 0.30
-25...+60 1.45
4 0-10V/PWM black
°
5 GND white
Ø165.3
Øe
Øa
6 Tacho red
Dimensions
4xØ4.5
VSW0150XSLBS VSW0150XSLCS
450±20
Ø1
R3G150AA03** R3G150AC01**
58
a 152 148
b 20 42
c 31,5 53,5
d 87 108
e 116 119
12 3 4 5 6 Wieland
Wieland 93.031.3253.0
93.032.3353.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 35
DC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 150
Optional
300 2 ■ Additional shaft seal see page 88
1,2
250
1,0
200
0,8
150
0,6
1
100
0,4
1
50
0,2
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
36 Fans and blowers for solid fuel heating systems · Edition 2022-06
R1G150AA63**
Air flow
Weight
Speed
Motor
Nominal voltage 24 V DC, Nominal voltagesbereich 16-28 V DC m3/h rpm W A db(A) Pa °C kg
Type Part number Fan type
Cable
R1G150AA6301 design ❶ 290 3030 31 1.40 66
A ❷ 290 3110 29 1.30 66
VSW0150XULCS M1G 055-BD 0 -25...+50 1.3
B ❶ 180 3190 26 1.20 67
R1G150AA6305 Plug ❷ 180 3360 22 1.00 67
design
Subject to changes. * A measured without scroll housing. B measured with scroll housing
4 Tach white
°
5 unlined
Ø165.3
Ø119
Ø148
4xØ4.5
450±20
Ø1
58
12 3 4 5 6 Wieland
Wieland 93.031.3253.0
93.032.3353.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 37
EC centrifugal blowers (exhaust air)
for solid fuel heating systems, single inlet, Ø 150
■ Type of protection: IP 54
■ Insulation class: "B"
■ Mounting position: any
from page 86 Scroll dimensions ■ Condensate discharges: none, open rotor
page 91, 93 Electrical connections H4), C)
■ Mode of operation:
More at www.ebmpapst.com Continuous operation (S1)
■ Bearings: Maintenance-free ball bearings
■ Max. exhaust gas temperature:
Continuous operation 250°C
■ Technical features:
See electrical connections p. 91 and 93
Pa
in H2O
■ EMC:
Interference emission acc. EN 61000-6-3
1,0
Optional
80 2 ■ Additional shaft seal see page 88
0,2
40
1
0 10 20 30 40 50 60 70 80 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and 1Heat output range
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
38 Fans and blowers for solid fuel heating systems · Edition 2022-06
G3G150DA03**
Air flow
Weight
Speed
Motor
Nominal voltage 1~200-240VAC, 50/60Hz m3/h rpm W A db(A) °C kg
Type Part number Fan type
Cable
G3G150DA0301 design
❶ 149 2535 16 0.17
❷ 149 2545 16 0.17
VPW0150XSLBS M3G 055-AI A ❸ 149 2585 15 0.16
66 -25...+60 2.0
❹ 149 2635 14 0.16
Plug
G3G150DA0305 design
Subject to changes.
137
149 8.6 Ø80
P9 P11
32 P10 P12
Connection Z
No. Function Color
118.2
1 N blue
2 PE green/yellow
62
3 L black
Ø116
P2 4 0-10V/PWM yellow
P1
P6 5 GND blue
P3 P5
87
P4 6 Tacho white
P7
P8
450±20
52
85±10
6
P X Y
85 94.2
1 -24.7 -100.6
137 2 -20.8 -87.1
149
P9 P11
8.6 Ø80 3 -34.3 -97.8
32 P10 P12 4 -30.4 -84.4
5 -49.0 97.3
6 -41.6 85.4
7 -57.5 92.0
118.2
8 -50.1 80.1
62
9 120.3 49.4
Ø116
10 108.5 41.9
P2
P1 11 114.9 57.8
P6
P3 P5 12 103.1 50.3
90.4
1 P4
2 P7
3 P8
4
5
6 52
85 94.2
Fans and blowers for solid fuel heating systems · Edition 2022-06 39
EC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 160
240
Standards and approvals
■ Standards: EN 60335-1, CE
200 ■ Approvals:
0,8
80
0,2
40
1
0 20 40 60 80 100 120 140 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
40 Fans and blowers for solid fuel heating systems · Edition 2022-06
R3G160AE01**
Air flow
Weight
Speed
Motor
Nominal voltage 1~200-240VAC, 50/60Hz m3/h rpm W A db(A) °C kg
Type Part number Fan type
Cable
R3G160AE0101 design ❶ 305 2600 40 0.33
❷ 305 2650 40 0.33
VSW0160XSLCS M3G 055-BD A ❸ 305 2670 38 0.27
66 -25...+60 1.55
Subject to changes.
108 49.5±1.5
47.
40 5 Connection
Ø1 No. Function Color
98 1 N blue
2 PE green/yellow
3 L black
4 0-10V/PWM yellow
5 GND blue
Ø160
4x90°
Ø210
Ø119
6 Tacho white
450±20
4xØ4.5
Wieland 1 2 3 4 5 6 Wieland
93.032.3353.0 93.031.3253.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 41
EC centrifugal fans (exhaust air)
for solid fuel heating systems, single inlet, Ø 180
in H2O
1
cfm
pfs
qV m3/h
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
42 Fans and blowers for solid fuel heating systems · Edition 2022-06
R3G180AH01** / R3G180AJ11**
Air flow
Weight
Speed
Motor
Nominal voltage 1~200-240VAC, 50/60Hz m3/h rpm W A °C kg
Type Part number Fan type
Cable
R3G180AH0101 design ❶ 295 2150 25 0.28
❷ 295 2150 25 0.28
VSW0180XSLCS M3G 055-BD A ❸ 295 2220 23 0.26
-25...+50 1.65
Cable
R3G180AJ1101 design ❶ 440 2660 60 0.55
❷ 440 2635 60 0.52
VSW0180XSLES M3G 055-CF B ❸ 440 2685 59 0.50
-25...+50 1.90
d c±1.5
47.
b 5 Connection
Ø1 No. Function Color
98 1 N blue
2 PE green/yellow
3 L black
4 0-10V/PWM yellow
5 GND blue
4x90°
Ø210
Øa
Øe
6 Tacho white
Dimensions
VSW0180XSLCS VSW0180XSLES
450±20
R3G180AH01** R3G180AJ11**
4xØ4.5
a 180 180
b 26 45
c 44,5 54,5
d 108 108
e 119 119
Wieland 1 2 3 4 5 6 Wieland
93.032.3353.0 93.031.3253.0
Fans and blowers for solid fuel heating systems · Edition 2022-06 43
EC centrifugal blowers (exhaust air)
for solid fuel heating systems, single inlet, Ø 180
■ Type of protection: IP 54
■ Insulation class: "B"
■ Mounting position: any
from page 86 Scroll dimensions ■ Condensate discharges: none, open rotor
page 91, 93 Electrical connections H4), C)
■ Mode of operation:
More at www.ebmpapst.com Continuous operation (S1)
■ Bearings: Maintenance-free ball bearings
■ Max. exhaust gas temperature:
Continuous operation 250°C
■ Technical features:
A See electrical connections p. 91 and 93
Pa
2,4 in H2O
■ EMC:
600 Interference emission acc. EN 61000-6-3
Interference immunity acc. EN 61000-6-2
Harmonics acc. EN 61000-3-2/3
■ Touch current: < 3,5mA acc. IEC 60990
500
2,0
7 ■ Approvals:
VDE, UL, CSA, CCC, EAC are applied for
12 Optional
200
0,8
11
■ Additional shaft seal see page 88
6
16
100 10
0,4
15
14
13 9 5
0 20 40 60 80 100 120 140 160 180 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and 1Heat output range
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
44 Fans and blowers for solid fuel heating systems · Edition 2022-06
G3G180FJ11** / G3G180GJ11**
Air flow
Weight
Speed
Motor
Nominal voltage 1~200-240VAC, 50/60Hz m3/h rpm W A db(A) °C kg
Type Part number Fan type
Cable
G3G180FJ1101 design ❶ 340 2690 55 0.50 74
❷ 340 2725 52 0.48 70
VPW0180XSLES ❸ 340 2810 46 0.44 66
❹ 340 2895 39 0.38 64
Plug ❺ 340 2500 44 0.40 72
G3G180FJ1105 ❻ 340 2500 40 0.37 67
design
❼ 340 2500 32 0.31 63
❽ 340 2500 25 0.25 61
M3G 055-CF A ❾ 340 2000 22 0.21 66
-25...+60 2.9
❿ 340 2000 20 0.19 62
Cable ⓫ 340 2000 16 0.16 57
G3G180GJ1101 design
⓬ 340 2000 13 0.13 55
⓭ 340 1500 9 0.09 59
Subject to changes.
174
Ø100 Connection Z
a 17 17
50 P9 P11 No. Function Color
P12
P10 1 N blue
A
2 PE green/yellow
3 L black
134.5
4 0-10V/PWM yellow
P6
5 GND blue
74.5
P5
6 Tacho white
Ø119
P7
P8
P2 Detail A P X Y
105
P1
G3G180GJ11** 1 -84.9 -88.4
450±20
P3
85±10
2 -75 -78.5
6
P4
101 115.3 66 3 -92 -81.3
4 -82 -71.4
5 16.5 134
174 6 16.5 120
Ø100 7 6.5 134
a 17 17
50 P9 P11 8 6.5 120
P10 P12 9 153 -5
A
10 139 -5
11 153 5
134.5
12 139 5
P6
74.5
P5
Ø119
Dimensions
P7
P8 VPW0180XSLES VPW0180XSLES
G3G180FJ11** G3G180GJ11**
105
1 P2
2
3
P1 a 186 223
4 P3
5
6 P4 101 115.3 66
Fans and blowers for solid fuel heating systems · Edition 2022-06 45
EC circulation blower
for solid fuel heating systems, Ø 210
2
1
200
0.8
0.6
100
0.4
0.2
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
46 Fans and blowers for solid fuel heating systems · Edition 2022-06
R3G210AE5310
Air flow
Weight
Speed
Motor
Nominal voltage 230 VAC, 50 Hz m3/h rpm W A °C kg
Type Part number Fan type
Subject to changes.
Connection X
No. Function Color
1 N blue
2 PE green/yellow
3 L black
4 GND blue
5 Tacho white
4x90°
Ø142
Ø210
Ø245
6 0-10V/PWM yellow
450+20
4 30 X
Ø7.5 Ø7
114.6 42.7±1.5
Ø230
X
1 4
2 5
3 6
Fans and blowers for solid fuel heating systems · Edition 2022-06 47
EC centrifugal fans (exhaust air)
for solid fuel heating systems, backward curved, single inlet, Ø 250
2
2
400
1
Air performance measured as per: ISO 5801, Installation category A, without scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at
1m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed 1Heat output range
and may vary depending on the installation situation. With any deviation to the standard setup, the specific approx. data; heat output depends on the specific system
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff. conditions.
48 Fans and blowers for solid fuel heating systems · Edition 2022-06
R3G250BE04H1
Air flow
Weight
Speed
Motor
Nominal voltage 1~200-277VAC, 50/60Hz m3/h rpm W A °C kg
Type Part number Fan type
Subject to changes.
Ø250
600+20
85±10
8
Fans and blowers for solid fuel heating systems · Edition 2022-06 49
Fans and blowers for solid fuel heating systems
Convection heat
50
Convection heat
Product overview
Dimensions in mm Type Part number Page
Centrifugal fans:
Tangential fans:
Ø 60 VTS0060XQFFS 55411.20400 68
Ø 60 VTS0060XQFHZ 55412.60600 68
Ø 60 VTS0060XUECS auf Anfrage 70
Ø 60 VTS0060XUECS auf Anfrage 70
Convection heat
Ø 65 VTS0065XQFFS 55416.30108 72
Ø 65 VTS0065XQFHS 83315.00001 72
Ø 65 VTS0065XQFHS 55416.40010 72
Ø 65 VTS0065XUECZ 55668.49110 74
Ø 65 VTS0065XUECZ 55668.49111 74
Ø 65 VTS0065XUECZ 55668.49112 74
Fans and blowers for solid fuel heating systems · Edition 2022-06 51
Fans and blowers for solid fuel heating systems
Convection heat
Convection heat is a convenient function of stoves and chimney trays. It ensures The convection heat sector likes to use tangential
that the warm air in a room is evenly distributed and warmed up more quickly. blowers. Centrifugal fans are particularly suitable
Normally, a stove is heated mainly by radiated heat. As warm air rises and colder for conveying very large quantities of heat. Tan-
air drops, it takes a while for the warm air to warm up the entire room. gential blowers are characterized by the fact that
they generate a laminar and wide air flow becau-
A fan helps to accelerate this process. To do this, it conveys the cooler air via se of their design. They are also durable and ope-
the hot surfaces of the stove and conveys it either directly into the room or into rate extremely quietly. EC tangential blowers
special ventilation ducts. Thanks to the combination of radiated and convection from ebm-papst are very economical thanks to
heat generated in this way, users can quickly benefit from pleasant heat through an efficient motor. Since they can be controlled
out the entire room. steplessly, the consumer can use them to adjust
the air performance to their needs, creating a
Convection heat
Pa
Pa
500 VHD0120X2MCS 70
2
VBS0175R2LDZ
60
400 B
C
50
0.2
B
300 A
40
B
1
200 30
A B C
0.1
20
100 A
10
A
qv 100 200 300 400 500 m³/h qv 100 200 300 400 m³/h
52 Fans and blowers for solid fuel heating systems · Edition 2022-06
Size, performance and cost-effectiveness
perfectly combined
Wood pellet and wood chip heating systems The advantages of fans from ebm-papst
have very special requirements: in solid-fuel heating technology:
The air flows must be provided economically in
each operating state and irrespective of the hea- Suitable for use in intake and exhaust air and for distribution of warm air
ting power. In addition, there is little space in the
stoves. ebm-papst offers the right AC and EC fans Low noise emissions
to overcome these challenges. They are tailored
Cost-effective operation
to different performance classes and equipped
with fan impellers optimized for biomass appli-
Robust and compact design
cations. Due to their compact design, they are
robust, durable and space-saving. This facilita-
Fan impellers that are adapted to the special requirements
tes having the optimum size, performance and of biomass boilers
cost-effectiveness in any application.
Convection heat
Efficient,
speed-controlled EC technology for optimum fuel utilization
Fans and blowers for solid fuel heating systems · Edition 2022-06 53
EC centrifugal blowers (ambient air)
VHS 108
Material/surface
■ Housing: Hot-dip aluminised sheet steel
■ Impeller: Hot-dip aluminised sheet steel
Characteristics
■ Efficient EC motor
■ Speed control via PWM interface possible
■ Direction of rotation:
clockwise, seen on impeller
■ Type of protection: IP 00
■ Insulation class: "I.Cl. H"
■ Mounting position:
from page 86 Scroll dimensions
any, except motor overhead
from page 90 Electrical connections ■ Mode of operation:
More at www.ebmpapst.com
Continuous operation (S1)
■ Max. fluid temperature 155°C
Convection heat
■ Design:
Motor anti-vibration mounted
■ Bearings: Maintenance-free ball bearings
■ Protection class: I
in H2O
Pa
400
1.5
300
1
200
0.5
100
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
54 Fans and blowers for solid fuel heating systems · Edition 2022-06
VHS 108
Weight
Nominal voltage 230VAC, 50Hz m3/h rpm W A db(A) °C kg
Type Part number
Subject to changes.
Convection heat
184
Ø1
20 ±0,1
67.5±0.5
4 x Ø2.8
reading direction
Leserichtung
101+1
45°
Ø58
Ø60±0.5
)
° (=360°
4x90
(95.5)
Fans and blowers for solid fuel heating systems · Edition 2022-06 55
AC centrifugal blowers (ambient air)
VHS 108
Material/surface
■ Housing: Hot-dip aluminised sheet steel
■ Impeller: Hot-dip aluminised sheet steel
Characteristics
■ Direction of rotation:
clockwise, seen on impeller
■ Type of protection: IP 00
■ Insulation class: "I.Cl. H"
■ Mounting position:
Shaft horizontal, Outlet upwards.
More mounting positions on request.
■ Mode of operation:
from page 86 Scroll dimensions Continuous operation (S1)
from page 90 Electrical connections
■ Max. fluid temperature 250°C
More at www.ebmpapst.com
■ Design:
Convection heat
200
150
0.5
100
50
0 20 40 60 80 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
56 Fans and blowers for solid fuel heating systems · Edition 2022-06
VHS 108
Weight
Nominal voltage 230VAC, 50Hz m3/h rpm W A db(A) °C kg
Type Part number
Subject to changes.
Convection heat
Ø1
08
Ø11
0±0.1
max. 161
.1
±0
18
Ø1
53±0.5
30.3+1.0
max. 3
max. 87.5
-0.4
130
°
min. 14 8±1.5
90.5±1 56±1
max. 172 max. 131
Fans and blowers for solid fuel heating systems · Edition 2022-06 57
AC centrifugal blowers (ambient air)
VHS 108
Material/surface
■ Housing: Sheet steel, hot-dip aluminized
■ Impeller: Aluminum
Characteristics
■ Direction of rotation:
clockwise, seen on impeller
■ Type of protection: IP 00
■ Insulation class: "I.Cl. H"
■ Mounting position: Shaft horizontal,
more mounting positions on request
■ Mode of operation:
Continuous operation (S1)
from page 86 Scroll dimensions
■ Max. fluid temperature 180°C
from page 90 Electrical connections
More at www.ebmpapst.com
■ Design:
Motor anti-vibration mounted
Convection heat
200
150
0.5
100
50
0 20 40 60 80 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
58 Fans and blowers for solid fuel heating systems · Edition 2022-06
VHS 108
Weight
Nominal voltage 230VAC, 50Hz m3/h rpm W A db(A) °C kg
Type Part number
Subject to changes.
90°
Convection heat
X 45°
Ø 3.2 H12
4
12
Ø
0
Ø 11 Ø1
08
Z
170±0.5
approx. 1.5 approx. 1.5
97
59.5 +0.3
-0.7
63+1
62±0.5 162.5±0.5
Z X
6±1
(180° rotated)
Ø 4.5
31
Fans and blowers for solid fuel heating systems · Edition 2022-06 59
AC centrifugal blowers (ambient air)
VHS 120
Material/surface
■ Housing: Hot-dip aluminised sheet steel
■ Impeller: Hot-dip aluminised sheet steel
Characteristics
■ Direction of rotation:
clockwise, seen on impeller
■ Type of protection: IP 00
■ Insulation class: "I.Cl. H"
■ Mounting position:
Shaft horizontal, Outlet upwards.
More mounting positions on request.
■ Mode of operation:
from page 86 Scroll dimensions Continuous operation (S1)
from page 90 Electrical connections
■ Max. fluid temperature 250°C
More at www.ebmpapst.com
■ Design:
Convection heat
300
1
200
0.5
100
0 20 40 60 80 100 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
60 Fans and blowers for solid fuel heating systems · Edition 2022-06
VHS 120
Weight
Nominal voltage 230VAC, 50Hz m3/h rpm W A db(A) °C kg
Type Part number
Subject to changes.
Convection heat
max. 12.5 61+1
45°
45°
0
Ø11
2.6
max. 179
2.6
Ø12
67.5±0.5
0±0.1
Ø7 Ø5 Ø7
(Ø58) 45°
Ø60±0.5
6
2.4 2.4
14±1.5 30
7
12±1
95.5
Fans and blowers for solid fuel heating systems · Edition 2022-06 61
EC centrifugal blowers (ambient air)
for solid fuel heating systems, dual inlet, Ø 120
Material/surface
■ Housing: Galvanised sheet steel
■ Impeller: Galvanised sheet steel
■ Rotor: Uncoated
Characteristics
■ Direction of rotation:
Clockwise, seen on rotor
■ Type of protection: IP 54
■ Insulation class: "B"
■ Mounting position: any
■ Condensate discharges: none (open rotor)
from page 86 Scroll dimensions ■ Mode of operation:
page 91 Electrical connections H4) Continuous operation (S1)
More at www.ebmpapst.com ■ Design: Motor anti-vibration mounted
on both sides
Convection heat
A
■ Touch current: < 3,5mA acc. IEC 60990
(Test circuit, illustration 4)
■ Cable exit: variable
4
400 ■ Protection class: I
1,6
200
0,8
100
0,4
1
0 40 80 120 160 200 240 280 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
62 Fans and blowers for solid fuel heating systems · Edition 2022-06
D3G120AA0311
Air flow
Speed 1)
Weight
Motor
Nominal voltage 1~230VAC, 50/60Hz m3/h rpm W A db(A) Pa °C kg
Type Part number
Subject to changes. 1) Nominal data in operating point with maximum load and 230VAC
Convection heat
162
79
63
64.5
170
Ø100
74
146
156
6
350+20 85 ±10
Fans and blowers for solid fuel heating systems · Edition 2022-06 63
AC centrifugal blowers (ambient air)
for solid fuel heating systems, dual inlet, Ø 120
Material/surface
■ Housing: Galvanised sheet steel
■ Impeller: Galvanised sheet steel
■ Rotor: Uncoated
Characteristics
■ Direction of rotation:
Clockwise, seen on rotor
■ Type of protection: IP 44,
depending on installation and position
■ Insulation class: "F"
■ Mounting position: any
from page 86 Scroll dimensions
■ Condensate discharges: none
page 93 Electrical connections A1) ■ Mode of operation:
More at www.ebmpapst.com
Continuous operation (S1)
■ Design: Motor anti-vibration mounted
Convection heat
on both sides
■ Bearings: Maintenance-free ball bearings
■ Motor protection: TOP wired internally
■ Touch current: < 0.75mA acc. to IEC 60990
in H2O
Pa
240
200 3
0,8
160
0,6
120 2
0,4
80
0,2
40
1
0 20 40 60 80 100 120 140 160 180 200 220 cfm
pfs
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
64 Fans and blowers for solid fuel heating systems · Edition 2022-06
D2E120AA0104
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB db(A) Pa °C kg
Type Part number
Subject to changes.
Convection heat
162
79
63
64.5
170
Ø100
74
146
156
6
85 ±10
350+20
Fans and blowers for solid fuel heating systems · Edition 2022-06 65
AC centrifugal blowers (ambient air)
backward curved, single inlet, Ø 175
Material/surface
■ Impeller: Plastic PA
■ Rotor: coated black
Characteristics
■ Direction of rotation:
Clockwise, seen on rotor
■ Type of protection: IP 44, depending on
installation and position acc. EN 60034-5
■ Insulation class: "F"
■ Mounting position: Shaft horizontal or rotor
on bottom; rotor on top on request
■ Condensate discharges: Rotor-side
from page 86 Scroll dimensions
■ Mode of operation:
page 93 Electrical connections A1), D)
Continuous operation (S1)
More at www.ebmpapst.com
■ Bearings: Maintenance-free ball bearings
Convection heat
■ Standards: EN 60335-1; CE
250
A
0.9
200 4
150 3
0.6
100
2
0.3
50
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
66 Fans and blowers for solid fuel heating systems · Edition 2022-06
R2E175RA5201
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50 Hz m3/h rpm W A μF/VDB °C kg
Type Part number
Subject to changes.
Convection heat
M4 (6x)
Ø132.8±0.2
Ø175
Ø72
61.3 Ø58±0.2
68.5±1
8
45 5±1
6
0+ 0
2 20
Fans and blowers for solid fuel heating systems · Edition 2022-06 67
Tangential blowers (ambient air)
VTS 0060
Material/surface
■ Housing: Hot-dip aluminised sheet steel
■ Impeller: Aluminum
Characteristics
■ Impeller diameter: 60 mm
■ Mounting position: horizontal
■ Permissible fluid temperature 0...+60 °C
■ Insulation class: "H"
Standards and approvals
■ Standards: EN 60335-1, CE;
EAC & UKCA on request
from page 86 Scroll dimensions
from page 89 Electrical connections
More at www.ebmpapst.com
Convection heat
Pa
pfs
qV m3/h
Pa
A B
A B
pfs
qV m3/h qV m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
68 Fans and blowers for solid fuel heating systems · Edition 2022-06
VTS 0060
Current draw
Input power
Air flow
Weight
Nominal voltage 230VAC, 50 Hz mm m3/h Pa W mA rpm °C kg
Type Part number
Subject to changes. Technical data are valid at free air flow and rated voltage. * Higher ambient temperatures on request.
Convection heat
e Dimensions
16
f f VTS0060XQFFS VTS0060XQFHZ
55411.20400 55412.60600
a 329 395
25
33
b 64 72
17
72
c 243 303
d 253 313
e 212 272
f 93 123
a
d b
61
36
c
3
56 3xØ2.4
Fans and blowers for solid fuel heating systems · Edition 2022-06 69
Tangential blowers (ambient air)
VTS 0060 with EC motor
Material/surface
■ Housing: Hot-dip aluminised sheet steel
■ Impeller: Aluminum
Characteristics
■ Electronics: integrated
■ Blower speed: variable via
0-10 V analogue voltage signal (Interface 26)
■ Impeller diameter: 60 mm
■ Mounting position: horizontal or vertical
with motor on bottom
■ Permissible fluid temperature 0...+60 °C
from page 86 Scroll dimensions
■ Insulation class: "H"
from page 89 Electrical connections ■ Type of protection: IP 20
More at www.ebmpapst.com ■ Protection class: 3; Operation with SELV
(safety extra low voltage)
Convection heat
Pa
A B
A B
pfs
qV 25 50 75 100 125 150 175 200 225 250 m3/h qV 25 50 75 100 125 150 175 200 225 250 m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
70 Fans and blowers for solid fuel heating systems · Edition 2022-06
VTS 0060 with EC motor
Current draw
Input power
Air flow
Weight
Nominal voltage 24VDC mm m3/h Pa W mA rpm °C kg
Type Part number
Subject to changes. Technical data are valid at free air flow and rated voltage. * Higher ambient temperatures on request.
e
Dimensions
16
f f
Convection heat
VTS0060XUECS VTS0060XUECS
on request on request
33
a 327 387
b 64,5 64,5
25
67
51
c 243 303
d 253 313
e 212 272
f 93 123
d b
51
36
c
3
96
83
50
56 3xØ2.4
GND N.C.
Hall out GND / Error
+18...28 VDC control voltage /
PWM 1-6 KHz
Fans and blowers for solid fuel heating systems · Edition 2022-06 71
Tangential blowers (ambient air)
VTS 0065
Material/surface
■ Housing: Hot-dip aluminised sheet steel
■ Impeller: Aluminum
Characteristics
■ Impeller diameter: 65 mm
■ Mounting position: horizontal
■ Permissible fluid temperature: 0...+60 °C
■ Insulation class: "H"
Standards and approvals
■ Standards: EN 60335-1, CE;
UKCA on request
from page 86 Scroll dimensions
page 89 Electrical connections
More at www.ebmpapst.com
Convection heat
Pa
90
80
70
60
50
40
30
20
10
pfs
90
80
B
70
60 A C
50
40
30
20 A B C
10
pfs
qV 50 100 150 200 250 300 350 m3/h qV 50 100 150 200 250 300 350 m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
72 Fans and blowers for solid fuel heating systems · Edition 2022-06
VTS 0065
Current draw
Input power
Air flow
Weight
Nominal voltage 230VAC, 50 Hz mm m3/h Pa W mA rpm °C kg
Type Part number
Subject to changes. Technical data are valid at free air flow and rated voltage. * Higher ambient temperatures on request.
Convection heat
e Dimensions
f f
18
16
72
c
3
108
90
56
64 3xØ2.4
Fans and blowers for solid fuel heating systems · Edition 2022-06 73
Tangential blowers (ambient air)
VTS 0065 with EC motor
Material/surface
■ Housing: Hot-dip aluminised sheet steel
■ Impeller: Aluminum
Characteristics
■ Electronics: integrated
■ Blower speed: variable via
0-10 V analogue voltage signal (Interface 26)
■ Impeller diameter: 65 mm
■ Mounting position: horizontal or vertical
with motor on bottom
■ Permissible fluid temperature: 0...+70 °C
from page 86 Scroll dimensions
■ Insulation class: "H"
page 89 Electrical connections ■ Type of protection: IP 20
More at www.ebmpapst.com ■ Protection class: 3; Operation with SELV
(safety extra low voltage)
Convection heat
Pa
1600 A
1400 B
C
1200
A B C
pfs
qV 50 100 150 200 250 300 m3/h qV 50 100 150 200 250 300 m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
1600 against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
protection
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
1400have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
values
1200
74 Fans and blowers for solid fuel heating systems · Edition 2022-06
VTS 0065 with EC motor
Current draw
Input power
Air flow
Weight
Nominal voltage 24VDC mm m3/h Pa W mA rpm °C kg
Type Part number
Subject to changes. Technical data are valid at free air flow and rated voltage. * Higher ambient temperatures on request.
d
e 6
Convection heat
Dimensions
12
2.8
22 67
51
94
34
108
GND N.C.
Hall out GND / Error
+18...28 VDC control voltage /
PWM 1-6 KHz
Fans and blowers for solid fuel heating systems · Edition 2022-06 75
Fans and blowers for solid fuel heating systems
76
Combustion air blower
Product overview
Dimensions in mm Type Part number Page
Ø 140 VHS0140X2MES G2E140AL4001 80
Ø 160 VHS0160X2MJS G2E160AY5091 82
Fans and blowers for solid fuel heating systems · Edition 2022-06 77
Fans for solid fuel heating systems
Combustion air blowers convey air from the ebm-papst offers a wide range of centrifugal fans in various sizes, with both AC and
surroundings to stoves and heaters and convey EC technology. The fan impellers are generally forward-curved. The advantage of EC
this into the combustion chamber. This enables centrifugal fans is that their speed can be controlled. This means that the air volume
the biomass to be burned optimally. A perfect can always be optimally adapted to the requirements. If less heat is required, the sto-
mixture of air and fuel ensures hygienic com- ve runs at a low level – less fuel is burnt and the demand for air is reduced. If it is very
bustion of wood pellets or wood chips. This re- cold outside, the heating system runs at full speed by using more air to burn more
duces the formation of combustion residues to biomass. As it adapts optimally to the heating load, the fan operates efficiently and
a minimum. ensures optimum fuel utilization.
Do you want to selectively control the supply of combustion air, for example using
a vane anemometer? Then feel free to contact us. Together we will find the ideal
solution for your requirements.
Combustion air blower
600
G2E160AY5091
500
2
400
300
1
200
G2E140AL4001
100
78 Fans and blowers for solid fuel heating systems · Edition 2022-06
Clean & efficient
combustion
Our fans and blowers ensure clean and efficient combustion
in solid fuel heating systems, through design and quality, and thus,
ultimately, that people can enjoy a cozy home.
Fans and blowers for solid fuel heating systems · Edition 2022-06 79
AC centrifugal blowers (intake air)
for solid fuel heating systems, single inlet, Ø 140
Material/surface
■ Housing: Die-cast aluminium
■ Impeller: Galvanised sheet steel
■ Rotor: Partially cast in aluminium
Characteristics
■ Direction of rotation:
clockwise, seen on impeller
■ Type of protection: IP 44
■ Insulation class: "B"
■ Mounting position: any
■ Condensate discharges: none
from page 86 Scroll dimensions ■ Mode of operation:
page 93 Electrical connections A1) Continuous operation (S1)
More at www.ebmpapst.com ■ Bearings: Maintenance-free ball bearings
■ Motor protection: TOP wired internally
■ Touch current: < 0.75mA acc. to IEC 60990
(test circuit, illustration 4)
■ Cable exit: variable
■ Protection class: I
Pa
in H2O
cfm
pfs
qV m3/h
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
80 Fans and blowers for solid fuel heating systems · Edition 2022-06
G2E140AL4001
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 1~230VAC, 50Hz m3/h rpm W A μF/VDB db(A) Pa °C kg
Type Part number
❶ 415 2100 111 0.48 62
VHS0140X2MES G2E140AL4001 M2E 068-CF A ❷ 415 2350 98 0.43
2.0/450
62
0 -25...+60 3.0
Subject to changes.
130 227
115 103
94 5
6,3
M4
92
175
450
248
Ø130-1
107
100
Fans and blowers for solid fuel heating systems · Edition 2022-06 81
AC centrifugal blowers (intake air)
for solid fuel heating systems, single inlet, Ø 160
Material/surface
■ Housing: Die-cast aluminium
■ Impeller: Galvanised sheet steel
■ Rotor: Partially cast in aluminium
Characteristics
■ Direction of rotation:
clockwise, seen on impeller
■ Type of protection: IP 44
■ Insulation class: "B"
■ Mounting position: any
■ Condensate discharges: none
from page 86 Scroll dimensions ■ Mode of operation:
page 93 Electrical connections A1) Continuous operation (S1)
More at www.ebmpapst.com ■ Bearings: Maintenance-free ball bearings
■ Motor protection: TOP wired internally
■ Touch current: < 0.75mA acc. to IEC 60990
(test circuit, illustration 4)
■ Cable exit: variable
■ Protection class: I
2,4 in H2O
Pa
Optional
3 ■ Speed monitoring via Hall IC
400
1,6
300
1,2
200
0,8
100
0,4
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst scroll housing without
protection against accidental contact. Suction-side noise levels: LwA as per ISO 13347, LpA measured at 1m
distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and
may vary depending on the installation situation. With any deviation to the standard setup, the specifi c
values have to be checked and reviewed once installed or fi tted! For detailed information see page 94 ff.
82 Fans and blowers for solid fuel heating systems · Edition 2022-06
G2E160AY5091
Capacitor
Air flow
Weight
Speed
Motor
Nominal voltage 230VAC, 50Hz m3/h rpm W A μF/VDB db(A) Pa °C kg
Type Part number
Subject to changes.
130 227
115 103
94 5
6,3
M4
92
175
450
248
Ø130-1
107
100
Fans and blowers for solid fuel heating systems · Edition 2022-06 83
Fans and blowers for solid fuel heating systems
Additional information
84
Additional information
Contents
Page
Scroll dimensions 86
Additional shaft seal 88
Electrical connections EC tangential blowers 89
Electrical connections EC 90
Electrical connections AC 93
Electrical connections Hall IC 93
Technical parameters & scope 94
Additional information
Fans and blowers for solid fuel heating systems · Edition 2022-06 85
Scroll dimensions
Ø 160 139 132 127 122 116 111 106 100 96 93 92 98 107 11
Ø 180 156 149 143 137 131 125 119 113 108 104 103 110 120 12
Ø 210 182 174 167 160 152 146 139 132 127 121 120 128 140 14
Ø 250 218 209 200 192 182 175 167 158 152 145 144 154 168 19
Subject to changes.
86 Fans and blowers for solid fuel heating systems · Edition 2022-06
Scroll housing Scroll housing
without inlet nozzle with inlet nozzle
Additional information
Ø 160 100-120 3-5 8-11 10 10
Ø 180 110-130 3-5 8-11 12 12
Ø 210 120-135 3-5 8-11 12 12
Ø 250 140-160 3-5 8-11 12 12
Subject to changes.
Fans and blowers for solid fuel heating systems · Edition 2022-06 87
Additional shaft seal
Shaft seal
X
Additional information
88 Fans and blowers for solid fuel heating systems · Edition 2022-06
Electrical connection EC
(11) Tangential blowers
10K
2 speed output 1K
2 pulses per revolution
MMSZ4699T1
Uhigh = 12V HSO
Imax = 2mA
100K
control voltage
4 PWM: 1...6kHz; Uhigh = 10V; Ulow = 0V 100K control voltage
or control voltage 0...10VDC
stop: U < 1.0V or PWM < 10%
start: U > 1.5V or PWM > 15%
open port --> motor stand still
Additional information
Fans and blowers for solid fuel heating systems · Edition 2022-06 89
Electrical connection EC
H1)
Technical Characteristics:
• PFC (passive)
• Output 10VDC max. 1,1mA
• Tach output
• Control input 0-10VDC / PWM
• Over-temperature protected electronics / motor
Umin = 15V
Imax = L
Mains
brown +
10mA 50/60Hz N
blue -
PE
green/yellow
+
Voltage output
PWM U +10V max. 1.1mA
10K -
red
12V Lin/PWM control input
0-10VDC/PWM
yellow
GND 1µF
Counter
blue
Speed setting Speed Full Speed setting Tach output 1 pulse
Additional information
PWM 1 - 10kHz setting with speed 1V - 10V per revolution Isink max. 10mA
variable Controller white
resistance
680Ω
47V
100% PWM ->n=max 10V ->n=max
Alarm
approx. 10% PWM ->n=min approx. 1V ->n=min
< 10% PWM ->n=0 < 1V ->n=0
start up at > 14% start up at > 1.4V Speed display
Line 1 Line 2
0-10V
Tacho
PWM
+10V
GND
PE
N
L
Line Connection Color Assignment / function Line Connection Color Assignment / function
L brown Mains 50/60Hz, phase + 10V red Voltage output +10 V max. 1.1mA
1 N blue Mains 50/60Hz, neutral 0-10V / PWM yellow Control input (Impedance 100 kΩ)
2
PE green/yellow Protective earth GND blue GND
Tacho white Tach output: 1 pulse per revolution
90 Fans and blowers for solid fuel heating systems · Edition 2022-06
Electrical connection EC
H4)
Technical Characteristics:
1 - 10V PE
CON12
2 1 PE1
+10 V 1 3
3
Isink max. 1.1mA 2 4
10V/PWM
2
47k 47k
Speed setting with Speed setting with
1µF
GND
PWM 1 - 10kHz potentiometer 1
15V
Tacho 3 1
4
Additional information
3
680R 4 2
Imax = 10mA
ZMM47
2 2
10 K
12V
1 1
100% PWM ->n=max
10% PWM ->n=min
< 10% PWM ->n=0
Fans and blowers for solid fuel heating systems · Edition 2022-06 91
Electrical connection EC
J5)
Technical Characteristics:
1-10V
2 4 PWM/LIN
10V -> n = max 2 RE>100K
1V -> n = min 2
<1V -> n = 0 10K
Safe start-up 12V
at Unom -30%
from 4V Ucontr. 4
DUE
3
680R
DUE
47V
Speed Setting of values with GND
setting with temperatue controller 4 GND1
PWM 1-10kHz Reverse-polarity
protection
Additional information
1 1
33K
P
OUT
2 T 2
50003-1-0174
N
12V
4 4
100% PWM -> n = max T<10°C -> n = 0
10% PWM -> n = min T>45°C -> n = max
<10% PWM -> n = 0
Safe start-up
at Unom -30%
from 40% PWM
92 Fans and blowers for solid fuel heating systems · Edition 2022-06
Electrical connection Electrical connection
AC Hall IC
A1) / B) C) / D)
Pull up
L PE N U1 = blue
R4
C
U2 = black R3
white
Z = brown 680R
U1 U2 Z OK1
= green/yellow 5 1
D1
TW 4 2
blue
GND
B) Shaded pole motor
with TOP wired internally
Fan connections: white (OUT): Speed signal
blue (IN): Ground connection
TW
Additional information
VCC
red
Pull up
R1
Fan white
black
GND
Fans and blowers for solid fuel heating systems · Edition 2022-06 93
Technical parameters & scope
High standards for all ebm-papst products
Here at ebm-papst, we constantly strive to further improve our products in order to be able to offer you the best possible product for your
application. Careful monitoring of the market ensures that technical innovations are reflected in the improvements of our products. Based
on the technical parameters listed below and the ambience you want our product to operate in, we here at ebm-papst can always work
out the best solution for your specific application.
94 Fans and blowers for solid fuel heating systems · Edition 2022-06
Vibration test Standards
Vibration tests are carried out in compliance with Information on standards is provided
in the product-specific data sheets.
■ Vibration test in operation according to DIN IEC 68, parts 2-6
■ Vibration test at standstill according to DIN IEC 68, parts 2-6 EMC
Information on EMC standards is provided in the product-specific
Shock load data sheets. Complying with the EMC standards has to be estab-
Shock load tests are carried out in compliance with lished on the final appliance, as different mounting situations can
result in changed EMC properties.
■ Shock load according to DIN IEC 68, parts 2-27
Leakage current
Balancing quality Information on the leakage current is provided in the product-
Testing the balancing quality is carried out in compliance with specific data sheets.
Measuring is according to IEC 60990.
■ Residual imbalance according to DIN ISO 1940
■ Standard balancing quality level G 6.3 Approvals
In case you require a specific approval for your ebm-papst product
Should you require a higher balancing quality level for your (VDE, UL, EAC, CCC, CSA, etc.) please let us know.
specific application, please let us know and specify this when Most of our products can be supplied with the relevant approval.
ordering your product. Information on existing approvals is provided in the product-
specific data sheets.
Chemo-physical strain / performance parameters
Should you have questions about chemo-physical strain, Air performance measurements
please direct them to your ebm-papst contact. All air performance measurements are carried out on suction side
and on chamber test beds conforming to the specifications as per
Fields of application, industries and applications ISO 5801 and DIN 24163. The fans under test are installed in the
Additional information
Our products are used in various industries and applications: measuring chamber at free air intake and exhaust (installation
Ventilation, air-conditioning and refrigeration technology, clean category A) and are operated at nominal voltage, with AC also at
room technology, automotive and rail technology, medical and nominal frequency, and without any additional components such
laboratory technology, electronics, computer and office technolo- as guard grilles. As required by the standard, the air performance
gy, telecommunications, household appliances, heating, machines curves correspond to an air density of 1.2 kg/m3.
and plants, drive engineering. Our products are not designed for
use in the aviation and aerospace industry!
Fans and blowers for solid fuel heating systems · Edition 2022-06 95
Technical parameters & scope
Measurement conditions for air and noise measurement Sound pressure level and sound level
ebm-papst products are measured under the following conditions: All acoustic values are established according to ISO 13347, DIN
45635 and ISO 3744/3745 to accuracy class 2 and given in A-rated
■ A xial and diagonal fans in Direction of rotation “V” form.
in full nozzle and without guard grille When the sound pressure level (Lp) is measured, the microphone is
■ Backward curved centrifugal fans, free-running on the intake side of the fan being tested, usually at a distance of 1m
and with inlet nozzle on the fan axis.
■ Forward curved single and dual inlet centrifugal fans To measure the sound power level (Lw), 10 microphones are distri-
with housing buted over an enveloping surface on the intake side of the fan being
tested (see graphic). The sound power level measured can be roug-
Noise measurements hly calculated from the sound pressure level by adding 7 dB.
All noise measurements are carried out in low-reflective test rooms
with reverberant floor. Thus the ebm-papst acoustic test chambers Measuring confi guration
meet the requirements of precision class 1 according to DIN EN ISO as per ISO 13347-3 respectively DIN 45635-38:
3745. For noise measurement, the fans being tested are placed in a
reverberant wall and operated at nominal voltage (for AC, also at 10 measuring points
nominal frequency) without additional attachments such as the d≥D
guard grille. h = 1.5d ... 4.5d
Measurement area S = 6d2 + 7d (h + 1.5d)
Additional information
1,5d
D
3d
2d
96 Fans and blowers for solid fuel heating systems · Edition 2022-06
Combined level of multiple same-level sound sources
15
[dB(A)]
[dB]
Adding 2 noise sources with the same level results in a level increase of approx. 3dB.
The noise characteristics of multiple identical fans can be determined in advance based
10
9
Example:
8 A3G800 axial fans are on a condenser. According to the data sheet, the sound pressure
level of a fan is approximately 75dB(A). The level increase measured from the diagram is
5
9dB. Thus the overall sound level of the installation can be expected to be 84dB(A).
0
1 2 3 4 5 6 7 8 9 10 15 20 25
3
[dB(A)]
The acoustic performance of two different fans can be predetermined based on the
sound levels given in the data sheet. This is shown in the diagram opposite.
Increase in sound pressure / sound power level
2
Example:
There is an axial fan A3G800 with a sound pressure level of 75dB(A) at the operating
1,5
point and an axial fan A3G710 with 71dB(A) in a ventilation unit. The level difference is
4dB. The level increase can now be read in the diagram as approx. 1.5dB. This means that
1
Additional information
0
0 4 8 12 16 20 24
[dB]
Difference in level with two sources of sound [dB(A)]
Distance laws
0
[dB(A)]
Sound power level is independent of distance to the sound source. In contrast to this,
[dB]
sound pressure level decreases the further away the noise source is. The adjacent dia-
gram shows the decrease in level under far sound field conditions. Far sound field condi-
-10
tions apply whenever the distance between microphone and fan is big when compared
to fan diameter and wavelength to be considered. For more information on far sound
Decrease in sound pressure level
field, please consult the relevant literature on this complex topic. Per doubling of distan-
-20
ce, the level in the far sound field decreases by 6dB. In the near field of the fan, other
-26
The following example only applies to far sound field conditions and can vary strongly
depending on the installation effects: With an axial fan A3G300, a sound pressure level of
-40
65dB(A) was measured at a distance of 1m. According to the adjacent diagram, at a dis- 1 2 5 10 20 50 100
tance of 20m we would get a reduction by 26dB, i.e. a sound pressure level of 39dB(A). Distance [m]
Fans and blowers for solid fuel heating systems · Edition 2022-06 97
Fans and blowers for solid fuel heating systems
Contacts – Worldwide
98
Always find the right contact person!
www.ebmpapst.com/contact
Germany
GERMANY
Phone +49 871 707-0
Fax +49 871 707-465
info3@de.ebmpapst.com
Fans and blowers for solid fuel heating systems · Edition 2022-06 99
www.ebmpapst.com 2022-06 Only as pdf
ebm-papst ebm-papst
Mulfingen GmbH & Co. KG Landshut GmbH
Bachmühle 2 Hofmark-Aich-Straße 25
74673 Mulfingen 84030 Landshut
Germany Germany
Phone +49 7938 81-0 Phone +49 871 707-0
Fax +49 7938 81-110 Fax +49 871 707-465
info1@de.ebmpapst.com info3@de.ebmpapst.com