Professional Documents
Culture Documents
Drager Narkomed 2A 2B 3 4 Additional O2 Yoke
Drager Narkomed 2A 2B 3 4 Additional O2 Yoke
Drager Narkomed 2A 2B 3 4 Additional O2 Yoke
ADDITIONAL O2 YOKE
INSTALLATION PROCEDURE
NOTE: This procedure applies to NM2A, NM2B, NM3 and NM4 without a drop leaf table
top; domestic, ISO and CSA machines.
1. Disconnect all pipeline hoses and 6. Remove the "dummy" bolt and hex
set the System Power switch to ON. nut securing the yoke block to the
frame assembly.
2. Close the oxygen cylinder valve,
close all flow control valves. Press 7. Position the additional O2 yoke
the O2 Flush valve to drain oxygen assembly next to the existing O2
pressure from the system. yoke on the yoke spacer block on
the side of the machine (see Figure
WARNING: Verify that the oxygen 1). Secure the assembly to the
cylinder pressure gauge machine frame with two 5/16-24 x
indicates 0 Psi before 1-3/4 in. socket head screws and
continuing with this 5/16 lock washers.
procedure.
For CSA machines, install a 7/16
3. Set the System Power switch to ID vinyl cap on the head of each
STANDBY. screw. Secure the caps with a small
amount of Loctite #416 on the
4. Remove the screws securing the inside of each cap.
table top to the machine and
remove the table top. For ISO machines, remove the
green O2 label from the oxygen yoke
5. Pull the writing or keyboard tray and apply a white O2 label.
out to its fully extended position (if
applicable).
1
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
SP65003
YOKE SPACER
BLOCK
O2 YOKE
ASSEMBLY
(STANDARD)
N20 YOKE
ASSEMBLY
(OPTIONAL)
2
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
8. Locate the TEE fitting at the inlet 9. Examine the plug that was
port of the O2 cylinder pressure removed and determine the type of
regulator, and remove the plug fittings to be used at the regulator
from the TEE fitting. connection. Figure 2 shows the
correct assembly for two types of
On machines with E-Z plumb compression fittings.
piping, replace the existing elbow
with tee fitting P/N 4109404.
COMPRESSION NUT
IMPERIAL AND FERRULE
TYPE
COPPER
SWAGELOK TUBING
TYPE
COMPRESSION
NUT
TWO-PIECE
FERRULE SP65002
3
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
10. Connect a 3/16 in. diameter pre- 11. Reinstall the table top with the
bent copper tube between the O2 screws that were previously
yoke assembly check valve and the removed.
TEE fitting in the O2 cylinder
pressure regulator inlet port (see 12. Attach an O2 cylinder to the O2
Figure 3). Carefully form and trim yoke, making sure that a sealing
the tubing as necessary, and install washer is correctly installed and
the correct style 3/16 in. the index pins are properly engaged
compression nut and ferrule on the before tightening the bolt. The
inlet port end of the tube. Tighten cylinder should hang vertically
the connections at both ends after the handle is tight.
securely, and install a white/green
"O2" label at each end of the tube. 13. Perform the tests outlined in the
next section.
WHITE/ GREEN
O2 CYLINDER O2 TUBE LABELS
PRESSURE
REGULATOR
WHITE O2
LABEL
(ISO ONLY)
O2
CYLINDER
YOKE
OLD STYLE
COMPRESSION
FITTING
INSTALL CAPS
(CSA ONLY)
SP65002
NEW STYLE COMPRESSION NUT
AND TWO PIECE FERRULE
4
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
TEST PROCEDURE
2. Close the O2 cylinder valve and 15. Depress the O2FLUSH button for
remove the cylinder from the yoke. 15 seconds.
3. Observe the O2 cylinder pressure 16. Set the oxygen flow to 4 l/min.
gauge; after two minutes the
pressure shall not drop more than 17. The oxygen analyzer shall read 97-
50 Psi. 100% within 3 minutes.
4. Re-attach the O2 cylinder to the 18. Set the nitrous oxide flow to 2
yoke. l/min.
9. Set the Man/Auto selector to BAG. 25. Perform a complete PMS procedure
on the machine.
10. Close the APL valve.
5
RETURN TO SERVICE PROCEDURE TABLE OF CONTENTS
RETURN TO CD-ROM TABLE OF CONTENTS
NORTH
AMERICAN
DRÄGER Quality Service For Life®
Technical Service Department
3122 Commerce Drive
Telford, PA 18969
(215) 721-5402
(800) 543-5047
(215) 723-5935 Fax
Rev: B
Date: April 25, 1994
© 1994 N.A.D., Inc.