Professional Documents
Culture Documents
BS 6399-3
BS 6399-3
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
azmanco.com
azmanco.com
BRITISH STANDARD BS 6399-3:
1988
Incorporating
Amendments Nos. 1
and 3 and
Implementing
Amendment No. 2
azmanco.com
azmanco.com
BS 6399-3:1988
The preparation of this British Standard was entrusted by the Sector Board for
Building and Civil Engineering (B/-) to Technical Committee B/525/1, upon
which the following bodies were represented:
azmanco.com
azmanco.com
BS 6399-3:1988
Contents
Page
Committees responsible Inside front cover
Foreword ii
Section 1. General
1 Scope 1
2 Definitions 1
3 Symbols 1
4 Minimum impose roof loads 2
Section 2. Snow loads
5 Snow load on the roof 4
6 Snow load on the ground 4
7 Snow load shape coefficients 6
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
© BSI 11-1998 i
azmanco.com
azmanco.com
BS 6399-3:1988
Foreword
This Part of this British Standard Code of practice has been prepared under the
direction of the Civil Engineering and Building Structures Standards Committee
as a new Part to BS 6399 (formerly CP 3: Chapter V).
Imposed roof loads were previously included in BS 6399-1. This new Part of
BS 6399 now gives more information on imposed roof loads and in particular
gives snow loading data separately, allowing account to be taken of the variation
of snow in the United Kingdom and the effect of redistribution of snow on roofs
due to wind. Use of the uniformly distributed snow loads are subject to an
overriding minimum requirement.
This code can be used for design using permissible stresses or partial factors. In
the former case the values should be used directly while in the latter case they
should be factored by an appropriate value depending upon whether an ultimate
or serviceability limit state is being considered. The exception to this is the
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
ii © BSI 11-1998
azmanco.com
azmanco.com
BS 6399-3:1988
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Summary of pages
This document comprises a front cover, an inside front cover, pages i to iv,
pages 1 to 22, an inside back cover and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on
the inside front cover.
azmanco.com
azmanco.com
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
iv blank
azmanco.com
azmanco.com
BS 6399-3:1988
Section 1. General
1 Scope 2.4
site snow load
This Part of BS 6399 gives minimum imposed roof
loads for use in designing buildings and building the load intensity of undrifted snow at ground level,
components which are to be constructed and used in at the altitude of the site
the UK and the Channel Islands. It applies to: 2.5
a) new buildings and new structures; snow load shape coefficient
b) alterations and additions to existing buildings the ratio of the snow load on the roof to the undrifted
and existing structures. snow load on the ground
Caution is necessary in applying the snow load 2.6
calculations for sites at altitudes above 500 m and snow load on roof
specialist advice should be obtained in such the load intensity of the snow on the roof
situations (see appendix C).
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
the load intensity of undrifted snow in a sheltered h Assumed maximum height of snow in a
area at an assumed ground level datum of 100 m local drift (valleys of multi-span roofs and
above mean sea level, estimated to have an annual the intersections);
probability of exceedance of 0.02 hoi Vertical height of obstruction,
2.3 suffix i = 1, 2 or 3 to distinguish between
altitude of site several vertical heights on the same
diagram;
the height above mean sea level of the site where the
building is to be located, or is already located for an lsi Horizontal length of snow drift,
existing building suffix i = 1, 2 or 3 to distinguish between
several snow drifts on the same diagram;
salt Coefficient used in correcting basic snow
load on the ground for altitude;
© BSI 11-1998 1
azmanco.com
azmanco.com
BS 6399-3:1988 Section 1
sb Basic snow load (on the ground); c) a uniformly distributed load of 0.6 kN/m2
measured on plan for roof slopes of 30° or less; or
sd Snow load on roof; a uniformly distributed load
s0 Site snow load (on the ground); of 0.6 [(60 – a)/30] kN/m2 measured on plan for
roof slopes (a) greater than 30° and less than 60°;
a Angle of pitch of roof measured from the or zero load for roof slopes equal to or greater
horizontal; than 60°; or
b Equivalent slope for a curved roof; d) a concentrated load of 0.9 kN.
d Angle between the horizontal and a These loads assume that spreader boards will be
tangent to a curved roof at the eaves; used while any cleaning or maintenance work is in
progress on fragile roofs. The recommendations of
µi Snow load shape coefficient, suffix i = 1, 2, this clause may also be used where a ladder is
etc. to distinguish between shape permanently fixed to allow access to a roof for
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
2 © BSI 11-1998
azmanco.com
azmanco.com
Section 1 BS 6399-3:1988
© BSI 11-1998 3
azmanco.com
azmanco.com
BS 6399-3:1988
4 © BSI 11-1998
azmanco.com
azmanco.com
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Section 2
© BSI 11-1998
Figure 1 — Basic snow load on the ground
5
BS 6399-3:1988
azmanco.com
azmanco.com
BS 6399-3:1988 Section 2
7 Snow load shape coefficients NOTE The snow load shape coefficient, being a ratio of two
loads, is non-dimensional. The equations of the form 2h0i/s0 are
7.1 General principles correct, although apparently having the dimensions kN/m3,
because of the density correction. The correction is based on
Snow is naturally deposited in many different limited information which shows that the snow density is
patterns on a roof depending upon the wind speed, increased when the snow forms in drifts.
the wind direction, the type of snow, the external 7.2 Single span roofs
shape of the roof and the position and height of any
7.2.1 General. These are flat, monopitch, pitched or
surrounding roofs or obstructions. Therefore, it is
curved roofs of single span. The snow load shape
often necessary to consider several loading
coefficients do not include any allowances for
situations to ensure that all the critical load effects
drifting at parapets or other obstructions as these
are determined.
should be treated independently (see 7.4).
The primary loading conditions to be considered are:
7.2.2 Flat or monopitch roofs. For these roofs it is
a) that resulting from a uniformly distributed necessary to consider a single load case resulting
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
layer of snow over the complete roof, likely to from a uniform layer of snow over the complete roof.
occur when snow falls when there is little or no The value of the snow load shape coefficient (µi) is
wind; dependent on the angle of the pitch of the roof
b) those resulting from redistributed (or unevenly measured from the horizontal (a) and should be
deposited) snow, likely to occur in windy obtained from Figure 2. This value is assumed to be
conditions. constant over the complete roof area.
Condition b) can be caused by a redistribution of 7.2.3 Pitched roofs
snow which affects the load distribution on the 7.2.3.1 General. For this type of roof it is necessary
complete roof, e.g. snow transported from the to consider two load cases. For both cases the value
windward slope of a pitched roof to the leeward side; of the snow load shape coefficient (µi) is dependent
usually modelled as a uniformly distributed load on on the angle of pitch of the roof measured from the
the leeward side of the roof and zero load on the horizontal (a). For asymmetric pitched roofs, each
windward side. It can also be caused by side of the roof should be treated as one half of a
redistribution of snow which affects the load corresponding symmetric roof.
distribution on only a local part of the roof, e.g. snow
drifting behind a parapet; modelled as a variably 7.2.3.2 Case 1; uniform load. This results from a
distributed load. Both types of redistribution should uniform layer of snow over the complete roof. The
be considered if appropriate. For a complex roof value for the snow load shape coefficient should be
shape there may be several load cases associated obtained from Figure 3(a) ; this value is assumed to
with condition b). be constant over the complete roof area.
In general, load cases should be considered to act 7.2.3.3 Case 2; asymmetric load. This results from
individually and not together. In some transport of snow from one side of the ridge to the
circumstances more than one of the load cases will other side. This situation only needs to be
be applicable for the same location on the roof. When considered for roof slopes greater than 15°. The
this arises they should be treated as alternatives. value for the snow load shape coefficient for one
slope of the roof should be zero, i.e. no snow load.
NOTE However, where, for example, on a lower roof area
sheltered from all wind directions, there is the possibility of The value for the snow load shape coefficient for the
redistribution of snow from a higher roof to form a local drift on other slope should be obtained from Figure 3(b); this
top of a uniform snow load distribution on this lower roof, it value is assumed to be constant over the loaded
would be appropriate to consider the local drift load acting in
combination with the uniform snow load on the lower roof.
slope of the roof.
Redistribution of snow should be considered to occur
on any roof slope and at any obstruction, as it should
be assumed that the wind can blow from any
direction.
The equations given in Figure 2 to Figure 9 for
determining the snow load shape coefficients are
empirical; where they are associated with local
drifting of snow they include a correction to allow for
an increased weight density in the drift. Therefore,
when using the equations the dimensions of the
building and of the obstruction (b1, h01, ls1, b2, etc.)
should be in metres and the site snow load should be
in kN/m2.
6 © BSI 11-1998
azmanco.com
azmanco.com
Section 2 BS 6399-3:1988
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
© BSI 11-1998 7
azmanco.com
azmanco.com
BS 6399-3:1988 Section 2
7.4 Local drifting of snow on roofs Where simultaneous drifts in several valleys of a
7.4.1 General. When considering load cases using multispan roof are being considered in the design of
snow load shape coefficients obtained from this a structure as a whole, a maximum limit on the
subclause it should be assumed that they are amount of drifted snow on the roof should be
exceptional snow loads and that there is no snow applied. The total snow load per metre width in all
elsewhere on the roof. Appendix B explains the the simultaneous drifts should not exceed the
logical process behind the calculations. product of the site snow load and the length of the
building perpendicular to the valley ridges.
The snow load on the roof calculated using the
coefficients in this subclause should be assumed to 7.4.3 Roofs abutting or close to taller
be variably distributed. In the direction at 90° to the structures.
obstruction or valley it should decrease linearly to 7.4.3.1 Abrupt change of height. This subclause
zero over the length of the drift. In the direction applies where there is an abrupt change of height
parallel to the obstruction or valley it should be greater than 1 m, except that relatively slender
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
uniform and assumed to extend along the complete obstructions (e.g. chimneys) exceeding 1 m in height
length of the obstruction or valley, except where but less than 2 m wide and door canopies projecting
stated otherwise. not more than 5 m from the building should be
considered as local projections and obstructions
In some circumstances more than one local drift
with local drifting determined according to 7.4.5.
load case may be applicable for the same location on
For parapets, see 7.4.3.3.
a roof in which case they should be treated as
alternatives. The appropriate drift length and snow load shape
NOTE In determining the upper bound values for these drift coefficient for an abrupt change of height should be
loads account has been taken of known cases of excessive, drifting obtained from Figure 6 or from the following in
of snow in the UK. However, it is recommended that they are which all parameters are as defined in Figure 6.
treated as exceptional snow loads because of the rarity with
which they are expected to occur. For design, it is suggested that Drift length ls1 is the least value of 5h01, b1
these local drift loads are assigned a partial factor γf = 1.05. and 15 m.
7.4.2 Valleys of multi-span roofs. The appropriate Snow load shape coefficient m1 is the lesser of:
snow load shape coefficients and drift lengths for (2h01)/s0 and (2b)/ls1
local drifting of snow in valleys should be obtained
from Figure 5 or the following: where b is the larger value of b1 and b2
Drift length: with the restriction: m1 # 8
lsi = bi The snow load patterns implied in Figure 6 are also
Snow load shape coefficient: applicable for roofs close to, but not abutting, taller
m1 is the lesser of 2h/s0 and 2b3/(ls1 + ls2) buildings, with the exception that it is only
necessary to consider the load actually on the roof of
with the restriction m1 # 5 interest, i.e. the load implied between the two
and where all parameters are as defined in Figure 5 buildings can be ignored.
and below. NOTE The effect of structures close to, but not abutting the roof
under consideration will depend partly on the roof areas
For roofs of more than two spans with available from which snow can be blown into the drift and the
approximately symmetrical and uniform geometry, difference in levels. However, as an approximate rule, it is only
necessary to consider nearby structures when they are less
b3 should be taken as the horizontal dimension of than 1.5 m away.
three roof slopes (i.e. span × 1.5) and this snow load
7.4.3.2 Single pitched roof with ridge at 90° to a
distribution should be considered applicable to
taller structure. For this case, the local drift
every valley, although not necessarily
from 7.4.3.1 should be modified according to
simultaneously, (see below).
Figure 7, which implies a non-uniform variation in
NOTE If the structure is susceptible to asymmetric loading, the
designer should also consider the possibility of drifts of differing
the direction parallel to the obstruction.
severity in the valleys. 7.4.3.3 Parapets. Local drifting against parapets
For roofs with non-uniform geometry, significant should be determined in accordance with Figure 6 or
differences in ridge height and/or span may act as from the following in which all parameters are as
obstructions to the free movement of snow across defined in Figure 6.
the roof and influence the amount of snow Drift length ls1 is the least value of 5h01, b1
theoretically available to form the drift. Care should and 15 m.
be taken in the selection of b3 (the greater length of
Snow load shape coefficient µ1 is the lesser of:
building from which snow is available to be blown
into the drift). (2h01)/s0 and (2b)/ls1
8 © BSI 11-1998
azmanco.com
azmanco.com
Section 2 BS 6399-3:1988
where b is the larger value of b1 and b2 Drift length ls1 is the lesser value of 5h01 and b1.
with the restriction: µ1 ≤ 8 Snow load shape coefficient µ1 is the lesser of:
For drifting in a valley behind a parapet at a gable (2h01)/s0 and 5.
end the snow load at the face of the parapet should In addition, for door canopies projecting not more
be assumed to decrease linearly from its maximum than 5 m from the building, the value of snow load
value in the valley to zero at the adjacent ridges, shape coefficient should not exceed:
providing the parapet does not project much higher (2b)/ls1
than the ridge.
where b is the larger of b1 and b2 (see Figure 9).
NOTE For the purpose of this subclause, when considering a
parapet across the end of a valley the snow load at the ridge can
be assumed to be zero providing that the parapet does not project 8 Snow sliding down roofs
more than 300 mm above the ridge.
Under certain conditions snow may slide down a
7.4.4 Tee intersections. For intersecting pitched pitched or curved roof. The force Fs (in kN per metre
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
roofs the snow load shape coefficients and the drift width) exerted by a sliding mass of snow in the
lengths should be obtained from Figure 8. For this direction of slide is calculated from the following
case the variation in the direction parallel to the equation:
obstruction is non-uniform.
Fs = sdb sina
7.4.5 Local projections and obstructions. The effect
of drifting can be ignored if the vertical elevation where
area against which the drift could form is not
greater than 1 m2. The drifts which occur at local sd is the snow load on the roof (in kN/m2 );
projections and obstructions affect a relatively small b is the distance on plan from the gutter to the
area of roof only. Included in this category is drifting ridge (in metres);
against local obstructions not exceeding 1 m in
height and also drifting on canopies (projecting not a is the angle of pitch of the roof measured from
more than 5 m from the face of the building) over the horizontal.
doors and over loading bays, irrespective of the
height of the obstruction formed. A relatively tall, The appropriate value for sd is obtained from
slender obstruction over 1 m high but not more clause 5. It should be the most onerous value arising
than 2 m wide, may also be considered as a local from uniformly distributed snow on the roof slope
projection. For that specific case, the height against under consideration. It may result from either the
which the drift may form, h0i may be taken as the uniform load case or the asymmetric load case.
lesser of the projection width and the projection This force should be taken into account in the design
height. For parapets, see 7.4.3.3. of snowguards or snowfences if snow is likely to slide
The appropriate snow load shape coefficient at the off the roof endangering people or property below. It
face of the obstruction and the drift length should be should also be taken into account in the design of
obtained from Figure 9 or the following in which all any obstruction on a roof which may prevent snow
parameters are as defined in Figure 9. sliding off the roof.
© BSI 11-1998 9
azmanco.com
azmanco.com
BS 6399-3:1988 Section 2
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
10 © BSI 11-1998
azmanco.com
azmanco.com
Section 2 BS 6399-3:1988
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
© BSI 11-1998 11
azmanco.com
azmanco.com
BS 6399-3:1988 Section 2
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
12 © BSI 11-1998
azmanco.com
azmanco.com
Section 2 BS 6399-3:1988
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
© BSI 11-1998 13
azmanco.com
azmanco.com
BS 6399-3:1988 Section 2
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Figure 6 — Snow load shape coefficients and drift lengths at abrupt changes
in roof height and parapets
14 © BSI 11-1998
azmanco.com
azmanco.com
Section 2 BS 6399-3:1988
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Figure 6 — Snow load shape coefficients and drift lengths at abrupt changes
in roof height and parapets (concluded)
© BSI 11-1998 15
azmanco.com
azmanco.com
BS 6399-3:1988 Section 2
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Figure 7 — Snow load shape coefficients and drift lengths for single pitch roofs
abutting taller structures at 90°
16 © BSI 11-1998
azmanco.com
azmanco.com
Section 2 BS 6399-3:1988
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Figure 8 — Snow load shape coefficients and drift lengths for intersecting pitched roofs
© BSI 11-1998 17
azmanco.com
azmanco.com
BS 6399-3:1988 Section 2
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Figure 8 — Snow load shape coefficients and drift lengths for intersecting pitched
roofs (concluded)
18 © BSI 11-1998
azmanco.com
azmanco.com
Section 2 BS 6399-3:1988
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Figure 9 — Snow load shape coefficients and drift lengths for local
projections and obstructions
© BSI 11-1998 19
azmanco.com
azmanco.com
BS 6399-3:1988 Section 2
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
Figure 9 — Snow load shape coefficients and drift lengths for local
projections and obstructions (concluded)
20 © BSI 11-1998
azmanco.com
azmanco.com
BS 6399-3:1988
Where site snow loads with a probability of For England and Wales;
exceedance different from 0.02 are considered Meteorological Office,
appropriate, the designer should consult the Met 0 3,
Advisory Offices listed in appendix C for guidance.
London Road,
Appendix B Snow drift load BRACKNELL,
calculations Berkshire,
This appendix briefly describes the general process RG12 2SZ.
adopted for determining the maximum local load Tel: 01344 420242 Extn. 2299
intensity resulting from snow in a drift at a change
in roof height. It is included for designers who wish For Scotland;
to understand the parameters which influence the Meteorological Office.
magnitude of the snow loads associated with 231 Corstorphine Road,
drifting of snow. It is not intended for use in
EDINBURGH,
calculating snow load shape coefficients.
EH12 7BB.
Up to three basic checks are made as follows.
Tel: 0131 344 9721 Extn. 524
a) It is first assumed that the drift forms to the
top of the obstruction and the density of the snow For Northern Ireland;
increases from that of the fallen snow on the
ground. This check takes the general form of Meteorological Office,
limiting the snow load shape coefficient to: Progressive House,
rhoi/so 1 College Square East,
where BELFAST,
r is the weight density of the snow in the BT 1 6BQ.
drift (2 kN/m3 assumed); Tel: Belfast 28457
hoi is the height of the obstruction (in metres); The address of the advisory service of the Building
Research Establishment is as follows.
so is the site snow load (in kN/m2). Building Research Advisory Service,
b) In some cases, a check is then made to ensure Building Research Establishment,
that there is sufficient snow available on the roof
Building Research Station,
to form a drift to the top of the obstruction. This
check takes the general form of limiting the snow Garston, WATFORD,
load shape coefficient to: WD2 7JR.
2bi/lsi Tel: 01923 664664
where
© BSI 11-1998 21
azmanco.com
azmanco.com
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
22 blank
azmanco.com
azmanco.com
BS 6399-3:1988
Publications referred to
BS 5555, Specification for SI units and recommendations for the use of their multiples and of certain other
units1).
BS 6399, Loading for buildings.
BS 6399-1,Code of practice for dead and imposed loads.
BS 6399-2, Wind loads.
CP 3, Code of basic data for the design of buildings1).
CP 3: Chapter V, Loading.
ISO 3898, Bases for design of structures — Notations — General symbols1).
ISO 4355, Bases for design of structures — Determination of snow loads on roofs1).
BRE Digest 290, Loads on roofs from snow drifting against vertical obstructions and in valleys2).
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
1)
Referred to in the foreword only.
2)
Withdrawn.
© BSI 11-1998
azmanco.com
azmanco.com
|
|
|
|
|
|
|
|
|
BSI Ð British Standards Institution
|
|
|
|
|
|
| BSI is the independent national body responsible for preparing British Standards. It
|
| presents the UK view on standards in Europe and at the international level. It is
| incorporated by Royal Charter.
|
|
| Revisions
|
|
| British Standards are updated by amendment or revision. Users of British Standards
|
| should make sure that they possess the latest amendments or editions.
|
|
| It is the constant aim of BSI to improve the quality of our products and services. We
|
| would be grateful if anyone finding an inaccuracy or ambiguity while using this
| British Standard would inform the Secretary of the technical committee responsible,
|
| the identity of which can be found on the inside front cover. Tel: 020 8996 9000.
|
| Fax: 020 8996 7400.
|
|
|
Licensed Copy: Sheffield University, University of Sheffield, 23 October 2002, Uncontrolled Copy, (c) BSI
| BSI offers members an individual updating service called PLUS which ensures that
| subscribers automatically receive the latest editions of standards.
|
|
| Buying standards
|
| Orders for all BSI, international and foreign standards publications should be
|
| addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
|
|
| In response to orders for international standards, it is BSI policy to supply the BSI
|
| implementation of those that have been published as British Standards, unless
|
| otherwise requested.
|
|
| Information on standards
|
| BSI provides a wide range of information on national, European and international
|
| standards through its Library and its Technical Help to Exporters Service. Various
|
| BSI electronic information services are also available which give details on all its
|
| products and services. Contact the Information Centre. Tel: 020 8996 7111.
|
| Fax: 020 8996 7048.
|
|
| Subscribing members of BSI are kept up to date with standards developments and
| receive substantial discounts on the purchase price of standards. For details of
|
| these and other benefits contact Membership Administration. Tel: 020 8996 7002.
|
| Fax: 020 8996 7001.
|
|
| Copyright
|
|
| Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of
|
| the publications of the international standardization bodies. Except as permitted
| under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,
|
| stored in a retrieval system or transmitted in any form or by any means ± electronic,
|
| photocopying, recording or otherwise ± without prior written permission from BSI.
|
|
| This does not preclude the free use, in the course of implementing the standard, of
|
| necessary details such as symbols, and size, type or grade designations. If these
|
| details are to be used for any other purpose than implementation then the prior
| written permission of BSI must be obtained.
|
|
| If permission is granted, the terms may include royalty payments or a licensing
|
| agreement. Details and advice can be obtained from the Copyright Manager.
|
| Tel: 020 8996 7070.
|
|
|
|
|
|
|
|
|
BSI |
|
389 Chiswick High Road |
|
London |
|
W4 4AL |
|
|
|
|
|
|
azmanco.com
azmanco.com