Professional Documents
Culture Documents
Cromar UW TOOL
Cromar UW TOOL
Product code:
Blind Boxes
Blind Boxes &
& Gauge
Gauge Cutters
Cutters Blind Box-128
Tubing Gauge Cutter-130
Wireline Operations
sub-surface control, the operator can be assured that
the tubing is clear of any impeding matter.
A gauge cutter consists of a short bar with a machined
bore extending up the center, with elongated windows
for fluid by-pass. The up-set gauge ring on the bottom
is sized for application and has a large bevel cut to
provide a scraping edge. The top comes with an
industry standard thread connection complete with
fishing neck.
When ordering please specify Cromar product
number and actual o.d. of tool required.
Wireline Operations
string, guaranteeing uninhibited access with wireline
sub-surface controls.
A tubing swage consists of a solid bar with an up-set
in the middle and tapered at both ends. A center bore
with lateral ports provides fluid by-pass. An industry
standard thread connection with fishing neck is
provided on the top. The diameter of the tubing swage
should normally be matched to the tubing it is being
deployed in.
When ordering please specify Cromar product
number and actual o.d. of tool required.
Wireline Operations
An orientation lead impression block consists of a
cylindrical steel container with an open bottom end
which is filled with soft lead. The upper section
contains a lead impression plate, impression ball,
inner mandrel, outer sleeve, mandrel return spring
and A top sub equipped with an industry standard
thread connection complete with fishing neck. Various
diameters are available to suit operational
requirements.
Wireline Operations
in design to the conventional type. They are heavy-duty
tools with hardened and tempered, segmented cutting
mandrel sets, which collapse if the tool gets stuck, preventing
potential fishing operations.
Depending on the type of material being removed, each
broach cutting mandrel is able to broach out approximately
1/10” of an inch.
Broaching tools are usually supplied with a set of cutting
mandrels, sized from the restricted ID to the required ID.
When ordering please specify Cromar product number,
restricted i.d. and actual o.d. of broach required.
Wireline Operations
The centraliser is positioned above the running or
pulling tool in the toolstring, and its OD is sized to
suit the tubing. This procedure also allows the
centraliser to be used as a drift or gauge, in addition
to centering the toolstring.
Cromar Fluted Centralisers are available in various
diameters and lengths. They are supplied with industry
standard pin by box connections complete with fishing
necks.
Fluted Centraliser
Rev 0 [06.02] www.cromar.com
Wireline Operations - Utility Wireline Tools
Wireline Operations
Bow Spring Centraliser
Wireline Operations
Tubing End Locator
Wireline Brush
The Cromar Wireline Brush is designed to loosen
and remove paraffin, scale and other deposits from
Wireline Operations
the inside wall of production tubing, landing nipples
and other subsurface control equipment. This
operation is usually carried out with the well flowing
through a small choke, to remove the loose deposits.
Wireline Brush
Wireline Operations
Conversion Kit
The Cromar Dump Bailer Conversion Kit allows a
standard pump bailer assembly to be converted to
a dump bailer.
The kit consists of a bottom lower adapter sub
complete with piston, spring and cage. and a top
sub complete with industry standard pin connection
and fishing neck.
Conversion kits are available in various sizes to
match standard pump bailers.
Dump Bailer
Bailer Shoes
Cromar Pump Bailers are available with the following
types of bottom shoe, sized to suit operational
Wireline Operations
requirements:
• Ball shoe
Bailer Shoes
Cromar Pump Bailers are available with the following
types of bottom shoe, sized to suit operational
Wireline Operations
requirements:
• Ball shoe
Flapper Shoe
• Flapper shoe
Sample Bailer
Wireline Operations
Hydrostatic Bailer