Professional Documents
Culture Documents
Infusion Series Icbtwin
Infusion Series Icbtwin
ICB/TWIN
Infusion Series®
42461 050511
2
CONTENTS
Warranty .............................................................................................................2
Contents..............................................................................................................3
Troubleshooting ..................................................................................................4
Diagnostic Displays.............................................................................................9
Access ..............................................................................................................10
Control Board....................................................................................................11
Membrane Switch .............................................................................................12
Brew Valves (Early) ...........................................................................................13
Brew Valves (Current) .......................................................................................14
Refill Valves ......................................................................................................15
Tank Heaters .....................................................................................................17
Limit Thermostat...............................................................................................18
Temperature Probe............................................................................................19
DV Selector Switch ...........................................................................................21
On/Off Switch....................................................................................................22
Schematic Wiring Diagrams..............................................................................23
42461 081310
3
• Inspection, testing, and repair of electrical equipment should be performed only by qualified service person-
nel.
• All electronic components have ac line voltage and some have low voltage dc potential on their terminals.
Shorting of terminals or the application of external voltages may result in board failure.
• Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be permanent. If
an intermittent condition is encountered, the cause will likely be a switch contact or a loose connection at a
terminal or crimp.
• Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are
energized for more than ten minutes without a supply of water.
• The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will
help to avoid twists and kinks in the tubing.
• Make certain that all plumbing connections are sealed and electrical connections tight and isolated.
• This brewer is heated at all times. Keep away from combustibles.
WARNING
• Exercise extreme caution when servicing electrical equipment.
• Unplug the brewer when servicing, except when electrical tests are specified.
• Follow recommended service procedures.
• Replace all protective shields or safety notices.
Control Boards
1. Make sure ribbon cable is properly attached to the control board (ALL PINS INSERTED INTO PLUG).
2. Make sure there is a nylon insulating washer under each screw head that holds the control board to the
plastic front end cap. This is important for proper operation.
3. Make sure before servicing brewer that voltage is present at control board.
4. Press any warmer switch or observe if any indicator lights are glowing on the control panel. If so, proceed
with testing. If not, check for voltage across pins 1 & 2 of the ten pin J1 connector (black and white wires).
If voltage is present, replace the control board. If voltage is not present, check wiring and voltage across
terminal block (black and white). Correct the problem and retest before proceeding with testing.
NOTE: In the event of board replacement, technician will need to re-program customer's settings and/or recipes,
as well as re-calibrate the temperature probe in program level 3 and re-enter the serial number in level 4.
42461 081310
4
Refill does not shut off 1. Lime build up on probe Remove Level Probe and check
Power "ON" for lime deposits on tip. Clean and
reinstall.
Refill does not shut off 1. Refill valve Clean or replace valve as needed.
Power "OFF"
42461 081310
5
3. Water Level Probe Sensing Check refill circuit. Heaters will not
System turn on if water is not grounding
level probe.
Spitting or excessive steaming 1. Lime build up on temperature Inspect probe and tank assembly
(cont.) probe, tank or tank heater for excessive lime deposits. Delime
as required.
Brewer is making unusual noises 1. Plumbing lines Plumbing lines should not rest on
the counter top.
42461 081310
6
4. ON/OFF switch not in the "ON" The indicator lamp must be lit
position
Check/replace
9. Control board
Consistently low beverage level in 1. Brew volume Inspect the dispense valve and
the dispenser or beverage overflows NOTE: Volume adjustments must be sprayhead for excessive lime de-
dispenser made with sprayhead installed. posits. Delime as required.
42461 081310
7
Dry coffee grounds remain in the 1. Sprayhead Make sure sprayhead is present and
funnel holes are clear and unobstructed.
Low beverage serving tempera- 1. Thermal server/airpot not pre- Preheat server
ture heated before brew cycle
42461 081310
8
Temperature Too Low 1. Water temperature in the tank A) Wait for the brewer to heat to
does not meet the ready tempera- the proper temperature.
ture.
B) Disable the BREW LOCKOUT
function. Refer to programming
section for procedure.
Heating Time Too Long 1. Tank Heater failure. Replace or repair as needed
Fill Time Too Long 1. Water shut off to brewer Check water supply shut-off
Temp Sensor Out Of Range, Check 1. Temperature Sensor Probe Replace or repair as needed
For Bad Connections open
Temp Sensor Out Of Range, Check 1. Temperature Sensor Probe Replace or repair as needed
Wire For Shorts wire(s) shorted
42461 081310
9
42461 081310
12
42461 081310
13
42461 081310
14
Helpful
Hint
Wrap a thin paper clip around each meter
lead and extend past the tip by ¼" - ½". You
may need to sand off the clear coating on
some clips!
Location:
The brew valve is located inside the top cover behind
the front face plate.
Test Procedures:
1. Refer to the Programing Section for Service Tools/
Test Outputs/Brew Valve.
2. Be sure brew funnel & server are in place before
activating valve.
3. Check the valve for coil action. Turn on the valve
with the test mode. Listen carefully in the vicinity of
the brew valve for a click as the coil pulls the plunger
in.
If no sound is heard as described, proceed to
#4.
If the sound is heard as described, there may be
a blockage in the valve , hose, tank, or sprayhead.
Disconnect the brewer from the power source. FIG. 16-2 EXPLODED VIEW
Remove the valve and inspect for blockage, and
de-lime all related areas.
4. Connect the voltmeter leads to the coil terminals.
Turn on the valve with the test mode.
The indication will be 2-3VAC off, 120VAC on. Set Due to the internally rectified coil, do not
the meter to DC volts. The indication should be 150- attempt to test this type of coil with an ohm-
160VDC when off, 0V when on. If the polarity of meter meter. The reading will be open or very high
leads are reversed, reading will indicate -150-160VDC. resistance, depending on the polarity of your
(Double these readings for 240 volt coils) meter leads.
If voltage is present as described, but no coil action is
42461 081310
16
Location:
The brew valve is located inside the top cover behind
the front face plate.
Test Procedures:
1. Refer to the Programing Section for Service Tools/
Test Outputs/Brew Valve.
2. Be sure brew funnel & server are in place before
activating valve.
3. Check the valve for coil action. Turn on the valve
with the test mode. Listen carefully in the vicinity of
the brew valve for a click as the coil pulls the plunger
in.
If no sound is heard as described, proceed to #4.
If the sound is heard as described, there may be a
blockage in the valve , hose, tank, or sprayhead. Dis-
connect the brewer from the power source. Remove FIG. 17-2 LATE MODEL BREW VALVE
the valve and inspect for blockage, and de-lime all
related areas.
4. Connect the voltmeter leads to the coil terminals.
Turn on the valve with the test mode.
The indication will be 2-3VAC off, 120VAC on. Set
the meter to DC volts. The indication should be 150- Due to the internally rectified coil, do not attempt to
160VDC when off, 0V when on. If the polarity of meter test this type of coil with an ohmmeter. The reading
leads are reversed, reading will indicate -150-160VDC. will be open or very high resistance, depending
(Double these readings for 240 volt coils) on the polarity of your meter leads.
SCREEN
STRAINER
42461 081310
19
2268W 1425W
Large Small
Dia. Dia.
HEATER RESISTANCE
1425W-120V 9.5-11.0
3500W-240V 15.1-17.6
1680W-120V 7.9-9.2
1800W-120V 7.4-8.7
2268W-120V 5.9-6.9
FIG. 20-1 ICB TWIN TANK HEATERS
3000W-208V 12.9-15.1
Location: 3000W-240V 17.9-20.7
The tank heaters are located inside the tank and secured 3500W-200V 10.5-12.2
to the tank bottom. TERMINAL TO SHEATH - INFINITE (OPEN)
Test Procedures:
1. With a voltmeter, check voltage across the white NOTE- If any resistance is read between sheath and
wire (120V Models) or red wire (120/208-240V either terminal, remove and inspect heater for cracks
Models) from the terminal block and black wire in the sheath.
from the control board. Connect brewer to the Removal and Replacement:
power source. The indication must be 120 volts 1. Remove the top cover and front access panel as
ac for two wire 120 volt models or 208-240 volts previously described.
ac for three wire 120/208-240 volt models (during 2. Drain water from the tank.
a heating cycle). 3. Disconnect all the hoses from the tank.
2. Disconnect the brewer from the power source. 4. Remove the temperature probe from the grommet
in the tank lid.
If voltage is present as described, proceed to #3. 5. Remove the level probe from it's grommet.
If voltage is not present as described, refer to the Wir- 6. Disconnect the green wire from the tank lid.
ing Diagrams and check wiring harness. 7. Disconnect the wires from tank heater terminals.
8. Remove the nuts securing the tank lid to the
3. Disconnect the wires from the tank heater termi- tank.
nals. 9. Remove the hex nuts securing the tank heater to
4. Check resistance value across tank heater terminals the bottom of the tank. Remove tank heater(s) with
and compare to chart. gaskets and discard.
10. Install new tank heater(s) with gaskets to the bot-
If resistance is present as described, reconnect the tom of the tank and secure with two hex nuts.
wires, the tank heater is ok. 11. Install tank lid and secure with nuts.
If resistance is not present as described, replace the 12. Reconnect the wires to tank heater terminals.
tank heater.
42461 081310
20
Location:
The limit thermostat is located on the tank lid (on the
front of the tank on twins). FIG. 21-2 LIMIT THERMOSTATS
Test Procedures:
1. Disconnect the brewer from the power source and
allow to cool.
2. Disconnect the wires from the limit thermostat.
3. With an ohmmeter, check for continuity across
the limit thermostat terminals.
42461 081310
21
Location:
The temperature probe is inserted through the
tank lid assembly. FIG. 22-2 TEMPERATURE PROBE
Test Procedures:
1. Disconnect the brewer from the power source.
2. With a DC voltmeter, check voltage across the two
wires at J13 (J3 on ITB) on control board (black
probe to black wire, red probe to white wire refer
to FIG 19-2). Connect the brewer to the power
source. The indication should be between 4vdc
(cool) to 1vdc at ready temperature.
3. Disconnect the brewer from the power source.
42461 081310
23
Location:
The voltage selector switch is located on the
component mounting bracket on the base plate.
Test Procedure:
42461 081310
24
L1
L2
Location:
The power switch is located on the lower right
side of the trunk (ICB) or lower rear panel (ITCB).
42461 081310
25
RED
BLK
GRN
WHI
ITCB-DV & ITCB-C-DV
MAIN ON/OFF SWITCH
(Late Models only)
BLK-18
BLK-14
LIMIT SELECTOR
THERMOSTAT SWITCH
BLK-14 BLU-14 WHI-14
TANK HEATER
BLK-14 BLU-14
TANK HEATER
BLK 1680W WHI/VIO-14 RED-14
FUNNEL SENSOR (1425W ITCB-C-DV ONLY) 1800W
J1-1 VIO 1 3
J1-2
# WHI/VIO
/ BLU-14
. COM
BLK-14
4 N.O.
DILUTION WHI
2 WHI/VIO WHI/VIO
J17-1 SOL
/ DISPENSE
, WHI/GRN WHI/GRN WHI
SOL
0 REFILL
# WHI/BLU WHI/BLU WHI
J17-5 SOL
"
/
!
2 BLK
$
J17-10 WHI
WHI
J17-14
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PNK PROBE
J3-1
GRN
t
J3-5
J3-8
1 CONTROL PANEL ASSY
J2-1
BREW PROG L
A
J2-5
BREW PROG R
C
J2-10
HALF FULL
FULL
J2-20 ON/OFF
J2-22 STATIC
SHIELD
22
J16-1 GRN
WHI
MEMORY
RED BOARD
J16-5 BLK
J9-7
42461 081310
26
BLK RED
BLK RED
EMI
FILTER
BLK RED
BLK RED
LIMIT
TANK HEATER
THERMOSTAT BLK-14 RED-14 RED-14
BLK-14 BLU-14
3500W
BLK
FUNNEL SENSOR
J1-1 VIO 1 3
J1-2
# WHI/VIO
/ BLU-14
. COM
BLK-14
4 N.O.
DILUTION RED
2 WHI/VIO WHI/VIO
J17-1 SOL
/ DISPENSE
, WHI/GRN WHI/GRN RED
SOL
0 REFILL
# WHI/BLU WHI/BLU RED
J17-5 SOL
"
/
!
2 BLK
$
J17-10 RED
RED
J17-14
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PNK PROBE
J3-1
GRN
t
J3-5
J3-8
1 CONTROL PANEL ASSY
J2-1
BREW PROG L
A
J2-5
BREW PROG R
C
J2-10
HALF FULL
FULL
J2-20 ON/OFF
J2-22 STATIC
SHIELD
22
J16-1 GRN
WHI
MEMORY
RED BOARD
J16-5 BLK
42461 081310
27
RED
BLK
GRN
WHI
ITCB-DV & ITCB-C-DV
MAIN ON/OFF SWITCH
(Late Models only)
BLK-18
BLK-14
LIMIT SELECTOR
THERMOSTAT (1425W ITCB-C-DV ONLY) SWITCH
BLK-14 BLU-14 WHI-14
TANK HEATER
BLK-14 BLU-14
TANK HEATER
BLK 1680W WHI/VIO-14 RED-14
FUNNEL SENSOR 1800W
J1-1 VIO 1 3
OPTIONAL
J1-2 BRN/WHI
WHI/VIO SOL SWEETENER
#
/ BLU-14 KIT
COM BRN/WHI WHI
. BLK-14
4 N.O.
DILUTION WHI
2 WHI/VIO WHI/VIO
J17-1 SOL
/ DISPENSE
, WHI/GRN WHI/GRN WHI
SOL
0 REFILL
# WHI/BLU WHI/BLU WHI
J17-5 SOL
"
/
!
2 BLK
$
J17-10 WHI
WHI
J17-14
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PNK PROBE
J3-1
GRN
t
J3-5
J3-8
1 CONTROL PANEL ASSY
J2-1
BREW PROG L
A
J2-5
BREW PROG R
C
J2-10
HALF FULL
FULL
J2-20 ON/OFF
J2-22 STATIC
SHIELD
22
J16-1 GRN
WHI
MEMORY
RED BOARD
J16-5 BLK
J9-7
42461 081310
28
RED
BLK
WHI
Earth Ground
ITCB-DV & ITCB-C-DV
Chassis Ground MAIN ON/OFF SWITCH
WITH FACTORY SWEETENER (Late Models only)
BLK-18
BLK-14
LIMIT SELECTOR
THERMOSTAT SWITCH
BLK-14 BLU-14 WHI-14
TANK HEATER
BLK-14 BLU-14
TANK HEATER
BLK 1680W WHI/VIO-14 RED-14
FUNNEL SENSOR (1425W ITCB-C-DV ONLY) 1800W
J1-1 VIO 1 3
J1-2
# WHI/VIO
/ BLU-14
. COM
BLK-14
4 N.O.
DILUTION WHI
2 WHI/VIO WHI/VIO
J17-1 SOL
/ DISPENSE
, WHI/GRN WHI/GRN WHI
SOL
0 REFILL
# WHI/BLU WHI/BLU SOL WHI
J17-5
"
/ SWEETENER
! BRN/WHI WHI
SOL
2 BLK
$
J17-10 WHI
WHI
J17-14
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PNK PROBE
J3-1 LOW PRODUCT
GRN
DETECT SWITCH
t
BLU C NC
J3-5
NO
WHI/BLU
J3-8
1 CONTROL PANEL ASSY
J2-1
BREW PROG L
A
J2-5
BREW PROG R
C
J2-10
HALF FULL
FULL
J2-20 ON/OFF
J2-22 STATIC
SHIELD
22
J16-1
J16-5
J9-7
42461 081310
29
RED
BLK
GRN
WHI
MAIN ON/OFF SWITCH
(Late Models only)
BLK-18
BLK-14
LIMIT SELECTOR
THERMOSTAT SWITCH
BLK-14 BLU-14 WHI-14
TANK HEATER
BLK-14 BLU-14
TANK HEATER
BLK WHI/VIO-14 RED-14
1680W
FUNNEL SENSOR 2268W
J1-1 VIO 1 3
J1-2
# WHI/VIO
/ BLU-14
. COM
BLK-14
4 N.O.
BYPASS WHI
2 WHI/RED WHI/RED
J17-1 SOL
/ DISPENSE
, WHI/GRN WHI/GRN WHI
SOL
0 REFILL
# WHI/BLU WHI/BLU WHI
J17-5 SOL
"
/
!
2 BLK
$
J17-10 WHI
WHI
BRN/BLK SOL
BRN/WHI FUNNEL LOCK
J17-14
(Optional)
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PNK PROBE
J3-1
GRN
t
J3-5
J3-8
1 CONTROL PANEL ASSY
J2-1
BREW PROG L
A
J2-5
BREW PROG R
C
J2-10
HALF FULL
FULL
J2-20 ON/OFF
J2-22 STATIC
SHIELD
22
J16-1 GRN
WHI
MEMORY
RED BOARD
J16-5 BLK
J9-7
42461 081310
30
RED
BLK
GRN
WHI
MAIN ON/OFF SWITCH
(Late Models only)
BLK-18
BLK-14
LIMIT
THERMOSTAT TANK HEATER
BLU-14 BLU-14 RED-14
LEFT
FUNNEL SENSOR LIMIT
VIO 1 3 THERMOSTAT TANK HEATER
J20-1 BLU-14 BLU-14 RED-14
J20-3 WHI/VIO
LEFT
RIGHT
BYPASS WHI
FUNNEL SENSOR SOL
J21-1 YEL 1 3
RIGHT
# J21-3 WHI/YEL DISPENSE WHI
SOL
/ BLU-14
. COM
BLK-14 LEFT
4 N.O.
WHI/RED DISPENSE WHI
2 J17-1 SOL
/ ORN
, WHI/GRN
0 REFILL WHI
SOL
# WHI/BLU
J17-5
" BLU RIGHT
SOL
/ BLU/BLK FUNNEL LOCK
! RIGHT
(Optional)
2 BLK BYPASS WHI
$ SOL
GRY
J17-10 WHI
WHI
BRN/BLK LEFT
SOL
J17-14 BRN/WHI FUNNEL LOCK
(Optional)
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PROBE
PNK
J3-1
GRN
t
J3-5
CONTROL PANEL ASSY
J3-8
1 RIGHT RIGHT
FULL HALF
J2-1
RIGHT RIGHT
BREW ON/OFF
C
J2-5
RIGHT RIGHT
BREW PROG
B
LEFT
FULL LEFT LEFT
BREW PROG
LEFT C
J2-20
HALF
LEFT LEFT
J2-22 BREW
RIGHT ON/OFF
B
J16-1 GRN 22 ON/OFF
WHI
RIGHT LEFT
MEMORY LEFT
FULL BREW
RED BOARD FULL
A
J16-5 BLK
RIGHT
HALF LEFT
(Early Models only)
HALF
42461 081310
31
BLK RED
BLK RED
EMI
FILTER
BLK RED
BLK RED
LIMIT
TANK HEATER
THERMOSTAT BLK-14
BLK-14 BLU-14 RED-14
3500W
BLK
FUNNEL SENSOR
J1-1 VIO 1 3
J1-2
# WHI/VIO
/ BLU-14
. COM
BLK-14
4 N.O.
BYPASS RED
2 WHI/RED WHI/RED
J17-1 SOL
/ DISPENSE
, WHI/GRN WHI/GRN RED
SOL
0 REFILL
# WHI/BLU WHI/BLU RED
J17-5 SOL
"
/
!
2 BLK
$
J17-10 RED
RED
BRN/BLK SOL
BRN/WHI FUNNEL LOCK
J17-14
(Optional)
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PNK PROBE
J3-1
GRN
t
J3-5
BREW PROG L
A
J2-5
BREW PROG R
C
J2-10
HALF FULL
FULL
J2-20 ON/OFF
J2-22 STATIC
SHIELD
22
J16-1 GRN
WHI
MEMORY
RED BOARD
J16-5 BLK
42461 081310
32
BRN
BLU
SCHEMATIC WIRING DIAGRAM ICB TWIN 230V Chassis Ground TERM
BLOCK
GRN
RED
BLK
Chassis Ground EMI
FILTER
BLK-18
BLK-14
LIMIT
THERMOSTAT TANK HEATER
BLU-14 BLU-14 RED-14
LEFT
FUNNEL SENSOR LIMIT
VIO 1 3 THERMOSTAT TANK HEATER
J20-1 BLU-14 BLU-14 RED-14
J20-3 WHI/VIO
LEFT
RIGHT
BYPASS RED
FUNNEL SENSOR SOL
J21-1 YEL 1 3
RIGHT
# J21-3 WHI/YEL DISPENSE RED
SOL
/ BLU-14
. COM
BLK-14 LEFT
4 N.O.
WHI/RED DISPENSE RED
2 J17-1 SOL
/ ORN
, WHI/GRN
0 REFILL RED
SOL
# WHI/BLU
J17-5
" BLU RIGHT
SOL
/ BLU/BLK FUNNEL LOCK
! RIGHT
(Optional)
2 BLK BYPASS RED
$ SOL
GRY
J17-10 RED
RED
BRN/BLK LEFT
SOL
J17-14 BRN/WHI FUNNEL LOCK
(Optional)
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PROBE
PNK
J3-1
GRN
t
J3-5
CONTROL PANEL ASSY
J3-8
1 RIGHT RIGHT
FULL HALF
J2-1
RIGHT RIGHT
BREW ON/OFF
C
J2-5
RIGHT RIGHT
BREW PROG
B
LEFT
FULL LEFT LEFT
BREW PROG
LEFT C
J2-20
HALF
LEFT LEFT
J2-22 BREW
RIGHT ON/OFF
B
J16-1 GRN 22 ON/OFF
WHI
RIGHT LEFT
MEMORY LEFT
FULL BREW
RED BOARD FULL
A
J16-5 BLK
RIGHT
HALF LEFT
(Early Models only)
HALF
STATIC
SHIELD
230 VOLTS AC
2 WIRE + GND
SINGLE PHASE
37299.0004A 12/08 ©2008 BUNN-O-MATIC CORPORATION
42461 081310
33
TR-5 TR-2
TANK HEATER
RED BLK
TR-6
# LIMIT THERMOSTAT
/ BLU/BLK
. TR-1
4
2 WHI/VIO DILUTION (MAIN or LEFT) WHI
J10-1 WHI/BLU SOL
/ SOL REFILL WHI
, WHI/GRN DISPENSE WHI
SOL
0 WHI/YEL RIGHT DILUTION (DUAL DILUTION MODELS ONLY) WHI
SOL
# WHI/RED OPTIONAL SWEETENER WHI
J10-5 SOL
"
/
!
2
$
J10-10
WHI
J3-1
BLK
TEMP
PNK PROBE
LEVEL
PROBE
J2-1 OPTIONAL LOW PRODUCT
GRN t DETECT SWITCH
ORN
WHI/ORN
J2-5
1 1. JUMPER FOR DUAL DILUTION MODELS ONLY
2
3 2. JUMPER FOR SWEETENER MODELS ONLY
J2-8 3. JUMPER FOR DUAL DILUTION MODELS w/SWEETENER ONLY
BREW PROG L
A
J15-5
BREW PROG R
C
J15-10
HALF FULL
FULL
J15-20 ON/OFF
J15-22 STATIC
SHIELD
22
42461 081310
34
RED
BLK
WHI
Earth Ground Chassis Ground
MAIN ON/OFF SWITCH
BLK-18
BLK-14
LIMIT
THERMOSTAT SELECTOR SWITCH
BLK-14 BLU-14 WHI-14
TANK HEATER
BLK-14 BLU-14
TANK HEATER
BLK WHI/VIO-14 RED-14
1680W
FUNNEL SENSOR 2268W
J1-1 VIO 1 3
J1-2 COOLING FAN
C WHI/VIO
BLK
O BLU-14 MOT
N COM WHI
BLK-14
T N.O. BYPASS
R WHI/RED WHI/RED WHI
J17-1 SOL
O DISPENSE
L WHI/GRN WHI/GRN WHI
SOL
P REFILL
C WHI/BLU WHI/BLU WHI
J17-5 SOL
B
O
A
R BLK DILUTION
D WHI/VIO WHI/VIO WHI
J17-10 SOL
WHI WHI
J17-14
J15-1
TRANSFORMER
10VA
J15-5
WHI
J13-1
BLK
LEVEL
PNK PROBE
J3-1
GRN
t˚ t˚
J3-5 COOLING FAN
THERMISTOR
J3-8
1 CONTROL PANEL ASSY
J2-1
BREW PROG L
A
J2-5
BREW PROG R
C
J2-10
HALF FULL
FULL
J2-20 ON/OFF
J2-22 STATIC
SHIELD
J9-7
35
RED
BLK
WHI
GRN
LIMIT
THERMOSTAT TANK HEATER
BLU-14 BLU-14 RED-14
LEFT
FUNNEL SENSOR LIMIT
VIO 1 3 THERMOSTAT TANK HEATER
J20-1 BLU-14 BLU-14 RED-14
J20-3 WHI/VIO
LEFT
RIGHT
BYPASS WHI
FUNNEL SENSOR SOL
J21-1 YEL 1 3
RIGHT
C J21-3 WHI/YEL DISPENSE WHI
SOL
O BLU-14
N COM
BLK-14 LEFT
T N.O.
WHI/RED DISPENSE WHI
R J17-1 SOL
O ORN
L WHI/GRN
P REFILL WHI
SOL
C WHI/BLU
J17-5 RIGHT
B RED
K1 DILUTION
O BLK
A RELAY RIGHT
R BLK BYPASS WHI
D SOL
GRY
J17-10 WHI
WHI
RED/BLK LEFT
K2 DILUTION
J17-14 BLU/BLK
RELAY
K2 LEFT
J15-1 BLK WHI/YEL DILUTION WHI
SOL
TRANSFORMER COOLING FAN
10VA
BLK WHI
J15-5 MOT
WHI RIGHT
J13-1 K1
BLK DILUTION
BLK WHI/VIO WHI
SOL
PNK
J3-1 LEVEL
GRN
PROBE
t˚ t˚
J3-5 COOLING FAN
THERMISTOR
CONTROL PANEL ASSY
J3-8
1 RIGHT RIGHT
FULL HALF
J2-1
RIGHT RIGHT
BREW ON/OFF
C
J2-5
RIGHT RIGHT
BREW PROG
B
LEFT
FULL LEFT LEFT
BREW PROG
LEFT C
J2-20
HALF
LEFT LEFT
J2-22 BREW
RIGHT ON/OFF
B
22 ON/OFF
RIGHT LEFT
LEFT
FULL BREW
FULL
A
RIGHT
HALF LEFT
HALF
STATIC
120/208 OR 120/240 SHIELD
VOLTS AC
3 WIRE + GND
SINGLE PHASE
44145.0000A 01/11 ©2011 BUNN-O-MATIC CORPORATION
36