Professional Documents
Culture Documents
3M0-600 Required
3M0-600 Required
Version 1.0
QUESTION NO: 1
Which Wireless Infrastructure Device Manager (WIDM) command displays the generic settings of a
discovered 3Com Access Point (AP), i.e., device name, type, IP address, MAC address?
A. Present
B. Properties
C. Show
D. Display
Answer: B
QUESTION NO: 2
Which two are features of a Wireless LAN (WLAN) Infrastructure Basic Service Set? (Choose two.)
A. Management and control of the service area is performed by the access point (AP)
C. Only stations exist in the service area and no access point (AP) is used
D. Created when two or more Basic Service Sets are connected together
E. Members communicate directly with each other within the service area
Answer: A,E
QUESTION NO: 3
Which three are features of the 3Com Wireless LAN Controller WX4400? (Choose three.)
C. Stack up to four units together to support a maximum of 144 fit access points
Answer: A,D,F
QUESTION NO: 4
What is displayed by the 3Com Launcher/3Com Wireless LAN Manager if the antenna is retracted on a
3Com 11a/b/g Wireless PC Card with XJACK Antenna?
C. A picture with multiple curved lines showing the single strength between the PC and AP
Answer: B
QUESTION NO: 5
Which three are benefits of the 3Com Wireless LAN Mobility System? (Choose three.)
A. Improves throughput of critical data with multiple priority queues and queuing algorithms on each
wireless controller/switch
B. Provides centralized management for wireless controllers/switches and Managed Access Points
D. Eliminates the need to install access points (APs) throughout the building
E. Automates access point (AP) management, i.e., adjusts traffic loads, optimizes AP power, changes AP
channel assignments
Answer: B,C,E
QUESTION NO: 6
A. It immediately puts a port into the STP forwarding state, preventing an application from possibly
timing out
B. It enables Jumbo Frames on the port, providing higher data throughput on the link
C. It configures all the ports for 1,000 Mbps full duplex, providing maximum throughput
D. Like Rapid Spanning Tree Protocol (RSTP), PortFast provides faster convergence for wireless devices
when a bridge port goes up or downon the network
Answer: A
QUESTION NO: 7
Which best describes the 3Com Wireless LAN Controller and/or Switches?
A. Device that centrally controls multiple fat access points (APs) using IEEE 802.1X Network Login user
identity to deliver network services
B. Device that centrally controls multiple Managed Access Points (MAPs) using identity-based
networking to deliver network services
C. Device that centrally controls multiple fat access points (APs) using port-based user identity to deliver
network services
D. Device that centrally controls and powers multiple Managed Access Points (MAPs) using Microsoft
Active Directory user identity to deliver network services
Answer: B
QUESTION NO: 8
You have installed the 3Com 11a/b/g Wireless PC Card with XJACK Antenna card its software. What is
the next step required in the PC Card installation before you can access the Wireless LAN (WLAN)?
A. Using Wireless LAN Profile Manager, create a new profile, choose the appropriate access point (AP)
and click "Connect"
B. Using Wireless LAN Profile Manager, select the PC Card icon, click "Enable," then choose the
appropriate access point (AP) and click "Connect"
C. Using Wireless Infrastructure Device Manager (WIDM), choose the appropriate access point (AP) and
click "Connect"
D. Using Wireless LAN Profile Manager, click "Discover" and from the discovered-list choose the
appropriate access point (AP) and click "Connect"
Answer: A
QUESTION NO: 9
The 3Com Wireless LAN Controller WX4400 provides high-bandwidth, centralized control for up to 144
directly attached managed access points (MAPs).
A. False
B. True
Answer: A
QUESTION NO: 10
Which command in Windows XP would you use to begin the setup process for a wireless NIC?
A. Right click the Wireless Network Connection icon and choose Properties
B. Right click the Wireless Network Connection icon and choose Install
C. Right click the Wireless Network Connection icon and choose Configure
D. Right click the Wireless Network Connection icon and choose Load
Answer: A
QUESTION NO: 11
Which three are 3Com Wireless LAN Switch Manager (3WXM) network planning functions? (Choose
three.)
A. Define the geographical area for the wireless network
B. Define the RF model and the coverage areas for the floor
Answer: A,B,E
QUESTION NO: 12
What can the 3Com Wireless LAN Switch Manager (3WXM) do when it discovers a wireless rogue
device?
A. Verify the IP address of the rouge device and send the information to the management software,
which blocks future packets from the device
B. Verify the IP address of the rouge device and send the information to a Syslog server
C. Flood the access point (AP), causing a Denial of Service (DoS) condition
D. Deactivate the access point (AP) and send a message to the network management software
Answer: C
QUESTION NO: 13
Wireless LAN (WLAN) IEEE 802.11a Turbo Mode bonds two channels together for up to 108 Mbps data
rates.
A. True
B. False
Answer: A
QUESTION NO: 14
Which security protocol uses a hashed password for authentication rather than using a less secure
encrypted password?
Answer: B
QUESTION NO: 15
Which three are features of 3Com Dynamic Security Link? (Choose three.)
E. Local and remote access point (AP) authentication and encryption support
Answer: A,B,C
Answer: <m x1="57" x2="224" y1="316" y2="346" ss="0" a="0"></m><m x1="240" x2="408" y1="317"
y2="346" ss="0" a="1"></m><m x1="154" x2="320" y1="356" y2="386" ss="0" a="2"></m><m x1="11"
x2="177" y1="228" y2="261" ss="1" a="0"></m><m x1="9" x2="176" y1="155" y2="188" ss="1"
a="1"></m><m x1="9" x2="178" y1="82" y2="117" ss="1" a="2"></m><c start="2" stop="2"></c><c
start="0" stop="1"></c><c start="1" stop="0"></c>
QUESTION NO: 17
What is displayed by the 3Com Launcher/3Com Wireless LAN Manager if the antenna is retracted on a
3Com 11a/b/g Wireless PC Card with XJACK Antenna?
B. A picture with multiple curved lines showing the single strength between the PC and AP
Answer: D
QUESTION NO: 18
Which RF obstacle-planning functions are supported by the 3Com Wireless LAN Switch Manager
(3WXM)?
A. Create objects that may absorb RF signals and assign each object an attenuation factor
B. Assign an attenuation factor to all objects from an imported JPEG floor plan
C. Assign an attenuation factor to all objects from an imported GIF floor plan
Answer: A
QUESTION NO: 19
Which IP route service can be configured on 3Com Wireless Switch/Controller (WXs)?
A. Static routes to forward traffic generated by the WX to a specific IP router, if the traffic is on a local
VLAN or subnet
B. Static routes to forward traffic passing through the WX to a specific IP router, if the traffic is not on a
local VLAN or subnet
C. Static routes to forward traffic passing through the WX to a specific IP router, if the traffic is on a local
VLAN or subnet
D. Static routes to forward traffic generated by the WX to a specific IP router, if the traffic is not on a
local VLAN or subnet
Answer: D
QUESTION NO: 20
Which antenna type is typically used indoors to provide large coverage areas within a building?
A. Dipole antenna
B. Omnipole antenna
Answer: B
Answer: <m x1="6" x2="164" y1="420" y2="449" ss="0" a="0"></m><m x1="6" x2="165" y1="460"
y2="493" ss="0" a="1"></m><m x1="8" x2="164" y1="501" y2="529" ss="0" a="2"></m><m x1="6"
x2="165" y1="541" y2="571" ss="0" a="3"></m><m x1="4" x2="165" y1="581" y2="612" ss="0"
a="4"></m><m x1="15" x2="172" y1="316" y2="347" ss="1" a="0"></m><m x1="15" x2="173" y1="252"
y2="282" ss="1" a="1"></m><m x1="15" x2="173" y1="188" y2="218" ss="1" a="2"></m><m x1="14"
x2="173" y1="125" y2="155" ss="1" a="3"></m><m x1="13" x2="172" y1="58" y2="91" ss="1"
a="4"></m><c start="0" stop="3"></c><c start="1" stop="4"></c><c start="3" stop="2"></c><c
start="2" stop="1"></c><c start="4" stop="0"></c>
QUESTION NO: 22
Which three types of wireless devices may be detected as rogues by the 3Com Wireless LAN Switch
Manager (3WXM)? (Choose three.)
Answer: A,B,E
QUESTION NO: 23
Which wireless building-to-building bridge distance-related parameter must be set to ensure each
wireless bridge waits the appropriate period for a response from other wireless bridges?
QUESTION NO: 24
What is the optimal access point (AP) channel allocation configuration on a Wireless LAN (WLAN)?
A. Allow APs to automatically perform the hunting process to determine the best channels
Answer: D
QUESTION NO: 25
What is required before the network administer can connect to a 3Com Wireless LAN Switch/Controller
via telnet?
A. Enable telnet services, create an admin user/password on the device and assign the device an IP
address
B. Create a user/password on the device and set the console port authentication
C. Enable privilege mode, create a user/password on the device and set the console port authentication
D. Assign a master password to the device and set the console port authentication
Answer: A
QUESTION NO: 26
Choose the 3Com product that is represented by Sevice A in the network diagram.
Answer: C
QUESTION NO: 27
Choose the two features supported by the 3Com Wireless LAN Managed Access Point (MAP) 2750.
(Choose two.)
C. Dual-mode radio allows operation for both IEEE 802.11b/g and IEEE 802.11a
D. Dual-mode radio allows operation for either IEEE 802.11b/g or IEEE 802.11a
Answer: A,D
QUESTION NO: 28
Which RF obstacle-planning functions are supported by the 3Com Wireless LAN Switch Manager
(3WXM)?
A. Remove unnecessary layers from imported JPEG floor plans
B. Create objects that may absorb RF signals and assign each object an attenuation factor
C. Assign an attenuation factor to all objects from an imported JPEG floor plan
D. Assign an attenuation factor to all objects from an imported GIF floor plan
Answer: B
QUESTION NO: 29
Which functionality is transferred from 3Com Access Points (APs) to the 3Com Wireless LAN
Controller/Switch, creating Fit APs or Managed Access Points (MAPs) with the 3Com Wireless LAN
Mobility System?
Answer: D
QUESTION NO: 30
How does the 3Com Wireless LAN Switch Manager (3WXM) determine the geographic vicinity of a
wireless rogue device?
A. By using Global Positioning System (GPS) software
C. By distance from an authorized Managed Access Point (MAP) or triangulation on multiple authorized
MAPs
Answer: C
QUESTION NO: 31
You have launched the 3Com Wireless Infrastructure Device Manager (WIDM) software to configure
your Wireless LAN Access Point 8750. When you see the access point (AP) on your PC screen, it has an
exclamation point located to the left of the AP. What is the significance of the exclamation point?
C. The AP does not have an IP address assigned or is in a different subnet from your PC
Answer: C
QUESTION NO: 32
Which 5 GHz IEEE 802.11 WLAN band is best suited for building-to-building wireless communications?
D. 5.2 GHz
Answer: B
QUESTION NO: 33
Which procedure allows the network administrator to set up a Wireless LAN Access Point (AP) 8750 to
support RADIUS Authentication?
A. Use the 3Com Web Configuration Management System to login to the AP, click on the "RADIUS"
hyperlink and configure the RADIUS settings
B. Use the Wireless Infrastructure Device Manager (WIDM) to choose the AP from the list, click on the
"RADIUS" hyperlink and configure the RADIUS settings
C. Use a web browser to navigate to the RADIUS Authentication server, click on "Configure new device,"
choose the AP from the list and configure the RADIUS settings
D. Use the 3Com Web Configuration Management System to login to the 3Com Wireless LAN
Controller/Switch, choose the AP from the list and configure the RADIUS settings
Answer: A
QUESTION NO: 34
Which wireless network functions are supported by the 3Com Wireless LAN Switch Manager (3WXM)?
Answer: C
QUESTION NO: 35
C. Defines the ability to fine tune Wireless LAN configuration at the Physical (PHY) Layer to comply with
country-specific rules
Answer: C
QUESTION NO: 36
Wireless LAN (WLAN) IEEE 802.11a Turbo Mode bonds two channels together for up to 108 Mbps data
rates.
A. True
B. False
Answer: A
QUESTION NO: 37
What is the first step to configuring the Wireless LAN Access Point 8750 after the access point (AP) is
powered on and connected to the Ethernet port of a switch configured with VLANs?
A. Ensure the AP and your PC are both connected to the same VLAN and install and launch the Wireless
Infrastructure Device Manager software on your PC
B. Ensure the AP and your PC are connected as tagged members of different VLANs and install and
launch the Wireless Infrastructure Device Manager software on your PC
C. Ensure the AP and your PC are both connected as untagged members of different VLANs and install
and launch the Wireless Infrastructure Device Manager software on your PC
D. Connect your laptop PC to the second RJ-45 port on the AP and install and launch the Wireless
Infrastructure Device Manager software on your PC
Answer: A
QUESTION NO: 38
Which statement is true for Wireless LAN (WLAN) data and throughput rates?
A. Data rates drop as the distance to the access point (AP) decreases
B. Data rates on an IEEE 802.11a/g WLAN are not affected by distance from the access point (AP)
C. Data rates drop as the distance to the access point (AP) increases
D. Actual data throughput on a WLAN is about 25% of the defined throughput rate
Answer: C
QUESTION NO: 39
What is the estimated Mbps speed achieved with an IEEE 802.11a access point at the maximum distance
of 50 meters (164 feet)?
A. 54 Mbps
B. 36 Mbps
C. 2 Mbps
D. 12 Mbps
E. 6 Mbps
Answer: E
QUESTION NO: 40
Which best describes the information provided with the 3Com Wireless LAN Switch Manager (3WXM)
work order?
B. Information for the physical installation and software parameters, i.e., IP addresses, VLANs, channel
assignments, etc., of Managed Access Points (MAPs)
C. Information for the physical installation of the 3Com Wireless LAN Mobility System
D. Information for the physical installation of Managed Access Points (MAPs), 3Com Wireless LAN
Controller/Switch initial setup configuration information and projected RSSI information of the 3Com
Wireless LAN Mobility System
Answer: D
QUESTION NO: 41
Choose the two features supported by the 3Com Wireless LAN Managed Access Point (MAP) 2750.
(Choose two.)
B. Dual-mode radio allows operation for either IEEE 802.11b/g or IEEE 802.11a
C. Dual-mode radio allows operation for both IEEE 802.11b/g and IEEE 802.11a
Answer: B,D
QUESTION NO: 42
Which security protocol uses a hashed password for authentication rather than using a less secure
encrypted password?
Answer: A
QUESTION NO: 43
Which best describes the purpose of the Wireless LAN Switch/Controller "quickstart" command?
A. It is the command that first deletes any configuration on the device, then allows the administrator to
perform basic system configuration, i.e., IP address, date/time, etc.
B. It is the command that allows the administrator to perform basic system configuration, i.e., IP
address, date/time, etc.
C. It is the command that allows the administrator to perform advanced system configuration
D. It begins the configuration process that automatically assigns the IP address and configures the device
for basic operations
Answer: A
QUESTION NO: 44
The 3Com Wireless LAN Access Point 8xx0 family supports a single Virtual Access Point (VAP) per RF
radio installed in the unit.
A. False
B. True
Answer: A
Drag the 3Com product you would use for each location (A, B and C) to complete the 3Com Wireless LAN
Mobility System solution.
Answer: <m x1="672" x2="884" y1="333" y2="361" ss="0" a="0"></m><m x1="672" x2="886" y1="381"
y2="412" ss="0" a="1"></m><m x1="671" x2="887" y1="427" y2="458" ss="0" a="2"></m><m x1="670"
x2="885" y1="474" y2="507" ss="0" a="3"></m><m x1="671" x2="886" y1="524" y2="554" ss="0"
a="4"></m><m x1="433" x2="648" y1="437" y2="468" ss="1" a="0"></m><m x1="411" x2="621"
y1="174" y2="202" ss="1" a="1"></m><m x1="142" x2="359" y1="105" y2="137" ss="1" a="2"></m><c
start="2" stop="2"></c><c start="3" stop="1"></c><c start="4" stop="0"></c>
QUESTION NO: 46
Which IP route service can be configured on 3Com Wireless Switch/Controller (WXs)?
A. Static routes to forward traffic passing through the WX to a specific IP router, if the traffic is not on a
local VLAN or subnet
B. Static routes to forward traffic generated by the WX to a specific IP router, if the traffic is on a local
VLAN or subnet
C. Static routes to forward traffic passing through the WX to a specific IP router, if the traffic is on a local
VLAN or subnet
D. Static routes to forward traffic generated by the WX to a specific IP router, if the traffic is not on a
local VLAN or subnet
Answer: D
QUESTION NO: 47
Which wireless building-to-building bridge distance-related parameter must be set to ensure each
wireless bridge waits the appropriate period for a response from other wireless bridges?
Answer: A
QUESTION NO: 48
The network administrator can draw or import a JPEG or AutoCAD building floor plan using the 3Com
Wireless LAN Switch Manager (3WXM).
A. True
B. False
Answer: A
QUESTION NO: 49
Which three are standards/limitations when you are creating a mobility domain on the 3Com Wireless
LAN Switch/Controller (WX)? (Choose three.)
Answer: B,D,E
QUESTION NO: 51
What is required before the network administer can connect to a 3Com Wireless LAN Switch/Controller
via telnet?
A. Create a user/password on the device and set the console port authentication
B. Enable privilege mode, create a user/password on the device and set the console port authentication
C. Assign a master password to the device and set the console port authentication
D. Enable telnet services, create an admin user/password on the device and assign the device an IP
address
Answer: D
QUESTION NO: 52
Every mobility domain should have a minimum of two seed switches assigned one main and one backup.
A. True
B. False
Answer: B
QUESTION NO: 53
B. Configure, deploy and manage 3Com Wireless LAN Mobility Systems, i.e., Wireless LAN Controller
WX4400
Answer: B
QUESTION NO: 54
What is the System IP address for the 3Com Wireless LAN Switch and/or Controller?
A. It is the root IP address of a 3Com Wireless LAN Mobility solution used by all other switch/controllers
to establish the wireless network topology
B. It is the first IP address assigned to the wireless switch used exclusively for management
communications
C. It is one of the VLAN IP addresses assigned to a switch/controller used for wireless switch-to-switch
communications within a mobility domain
D. It is the IP address assigned to the master or seed switch/controller used to manage the entire
Wireless LAN Mobility system
Answer: C
QUESTION NO: 55
The 3Com 11a/b/g Wireless LAN Workgroup Bridge enables a laptop, PC or printer without built-in
wireless capability to connect to a wireless LAN.
A. False
B. True
Answer: B
Answer: <m x1="9" x2="329" y1="403" y2="437" ss="0" a="0"></m><m x1="10" x2="330" y1="455"
y2="485" ss="0" a="1"></m><m x1="11" x2="329" y1="502" y2="531" ss="0" a="2"></m><m x1="11"
x2="331" y1="548" y2="580" ss="0" a="3"></m><m x1="12" x2="328" y1="323" y2="355" ss="1"
a="0"></m><m x1="10" x2="328" y1="238" y2="267" ss="1" a="1"></m><m x1="12" x2="331" y1="158"
y2="187" ss="1" a="2"></m><m x1="11" x2="327" y1="79" y2="107" ss="1" a="3"></m><c start="0"
stop="3"></c><c start="2" stop="2"></c><c start="1" stop="1"></c><c start="3" stop="0"></c>
QUESTION NO: 57
To use IEEE 802.1X Network Login for the wireless LAN (WLAN), you must configure both the 3Com
access point (AP) and wireless LAN NIC for 802.1X authentication.
A. False
B. True
Answer: B
QUESTION NO: 58
Which best describes the features of the 3Com Wireless LAN Switch WX1200?
E. Centrally manages/controls up to six Managed Access Points (MAPs), improving security and
management
Answer: A
QUESTION NO: 59
Which two are features of a Wireless LAN (WLAN) Infrastructure Basic Service Set? (Choose two.)
B. Only stations exist in the service area and no access point (AP) is used
C. Created when two or more Basic Service Sets are connected together
D. Members communicate directly with each other within the service area
E. Management and control of the service area is performed by the access point (AP)
Answer: D,E
QUESTION NO: 61
Which Wireless Infrastructure Device Manager (WIDM) command displays the generic settings of a
discovered 3Com Access Point (AP), i.e., device name, type, IP address, MAC address?
A. Present
B. Properties
C. Show
D. Display
Answer: B
QUESTION NO: 62
Which three types of wireless devices may be detected as rogues by the 3Com Wireless LAN Switch
Manager (3WXM)? (Choose three.)
Answer: B,C,E
Drag each 3Com Wireless LAN Mobility System product to the set of features it supports.
Answer: <m x1="21" x2="339" y1="409" y2="441" ss="0" a="0"></m><m x1="22" x2="339" y1="459"
y2="486" ss="0" a="1"></m><m x1="20" x2="339" y1="504" y2="534" ss="0" a="2"></m><m x1="21"
x2="341" y1="554" y2="586" ss="0" a="3"></m><m x1="21" x2="339" y1="81" y2="111" ss="1"
a="0"></m><m x1="21" x2="338" y1="162" y2="192" ss="1" a="1"></m><m x1="22" x2="339" y1="241"
y2="271" ss="1" a="2"></m><m x1="21" x2="340" y1="329" y2="360" ss="1" a="3"></m><c start="0"
stop="1"></c><c start="1" stop="0"></c><c start="2" stop="3"></c><c start="3" stop="2"></c>
QUESTION NO: 64
Which procedure allows the network administrator to set up a Wireless LAN Access Point (AP) 8750 to
support RADIUS Authentication?
A. Use the 3Com Web Configuration Management System to login to the AP, click on the "RADIUS"
hyperlink and configure the RADIUS settings
B. Use a web browser to navigate to the RADIUS Authentication server, click on "Configure new device,"
choose the AP from the list and configure the RADIUS settings
C. Use the 3Com Web Configuration Management System to login to the 3Com Wireless LAN
Controller/Switch, choose the AP from the list and configure the RADIUS settings
D. Use the Wireless Infrastructure Device Manager (WIDM) to choose the AP from the list, click on the
"RADIUS" hyperlink and configure the RADIUS settings
Answer: A
QUESTION NO: 65
Which two are reasons a company may choose to use a building-to-building wireless bridge versus a
T1/E1 or fiber link? (Choose two.)
Answer: A,B
QUESTION NO: 66
Which two are functions of the 3Com Wireless LAN Switch Manager (3WXM) "deploy" command?
B. Sends a configuration file from 3WXM to a 3Com Managed Access Point (MAP)
C. Synchronizes configuration information between the 3WXM and a 3Com Wireless LAN
Switch/Controller
E. Allows a Wireless LAN Switch/Controller to be drawn into a Network Plan Mobility Domain
Answer: A,C
QUESTION NO: 67
A. Wireless devices that support packet bursting to increase throughput by sending more frames per a
given time period
B. Wireless devices that automatically change the connection speed based on the quality of the signal
C. Ability to dynamically support both IEEE 802.11b and IEEE 802.11g speeds
Answer: B
QUESTION NO: 68
Which antenna type is typically used indoors to provide large coverage areas within a building?
B. Omnipole antenna
D. Dipole antenna
Answer: B
Match each 3Com Wireless Switch (WX) IP service with its description.
Answer: <m x1="17" x2="173" y1="422" y2="454" ss="0" a="0"></m><m x1="16" x2="173" y1="466"
y2="493" ss="0" a="1"></m><m x1="15" x2="176" y1="505" y2="534" ss="0" a="2"></m><m x1="15"
x2="173" y1="542" y2="575" ss="0" a="3"></m><m x1="14" x2="174" y1="583" y2="614" ss="0"
a="4"></m><m x1="22" x2="182" y1="62" y2="95" ss="1" a="0"></m><m x1="25" x2="182" y1="127"
y2="157" ss="1" a="1"></m><m x1="24" x2="182" y1="191" y2="221" ss="1" a="2"></m><m x1="22"
x2="181" y1="256" y2="287" ss="1" a="3"></m><m x1="23" x2="183" y1="320" y2="352" ss="1"
a="4"></m><c start="1" stop="0"></c><c start="0" stop="1"></c><c start="3" stop="2"></c><c
start="2" stop="3"></c><c start="4" stop="4"></c>
QUESTION NO: 72
What is the benefit of Inter-Access Point Protocol (IAPP) support on the Wireless LAN Access Point 8xx0
family?
B. It allows the access points to create multiple Virtual Access Points (VAPs) for improved wireless
security
Answer: C
QUESTION NO: 73
What is displayed by the 3Com Launcher/3Com Wireless LAN Manager if the antenna is retracted on a
3Com 11a/b/g Wireless PC Card with XJACK Antenna?
C. A picture with multiple curved lines showing the single strength between the PC and AP
Answer: D
QUESTION NO: 74
Which three are 3Com Wireless LAN Switch Manager (3WXM) network planning functions? (Choose
three.)
E. Define the RF model and the coverage areas for the floor
Answer: B,C,E
QUESTION NO: 75
Which best describes the 3Com Wireless LAN Controller and/or Switches?
A. Device that centrally controls and powers multiple Managed Access Points (MAPs) using Microsoft
Active Directory user identity to deliver network services
B. Device that centrally controls multiple fat access points (APs) using port-based user identity to deliver
network services
C. Device that centrally controls multiple fat access points (APs) using IEEE 802.1X Network Login user
identity to deliver network services
D. Device that centrally controls multiple Managed Access Points (MAPs) using identity-based
networking to deliver network services
Answer: D
QUESTION NO: 76
Which three are features supported on the OfficeConnect ADSL Wireless 11g Firewall Router and the
3Com OfficeConnect Wireless 11g Cable/DSL Router? (Choose three.)
B. VPN termination
Answer: A,D,E
QUESTION NO: 78
Which 3Com Web Configuration Management System Advanced Settings software screen allows the
network administrator to configure the authentication, encryption and key management parameters for
an access point (AP)?
A. WEP settings
B. Radio settings
C. Wi-Fi settings
D. Security settings
Answer: D
QUESTION NO: 79
A. It enables Jumbo Frames on the port, providing higher data throughput on the link
B. Like Rapid Spanning Tree Protocol (RSTP), PortFast provides faster convergence for wireless devices
when a bridge port goes up or down on the networ
C. It configures all the ports for 1,000 Mbps full duplex, providing maximum throughput
D. It immediately puts a port into the STP forwarding state, preventing an application from possibly
timing out
Answer: D
QUESTION NO: 80
All 3Com OfficeConnect Wireless 54 Mbps 11g PC Cards support 108 Mbps data rate in Turbo mode.
A. False
B. True
Answer: A
QUESTION NO: 81
Which two are functions of the 3Com Wireless LAN Switch Manager (3WXM) "deploy" command?
A. Synchronizes configuration information between the 3WXM and a 3Com Wireless LAN
Switch/Controller
C. Sends a configuration file from 3WXM to a 3Com Managed Access Point (MAP)
D. Allows a Wireless LAN Switch/Controller to be drawn into a Network Plan Mobility Domain
Answer: A,B
QUESTION NO: 82
Which RF obstacle-planning functions are supported by the 3Com Wireless LAN Switch Manager
(3WXM)?
A. Assign an attenuation factor to all objects from an imported JPEG floor plan
B. Create objects that may absorb RF signals and assign each object an attenuation factor
D. Assign an attenuation factor to all objects from an imported GIF floor plan
Answer: B
QUESTION NO: 83
What is the #1 concern for Wireless LAN (WLAN) enterprise customers?
A. Management
B. Wireless coverage
C. Security
Answer: C
Match each Radio Frequency (RF) propagation issue with its description.
Answer: <m x1="8" x2="158" y1="311" y2="341" ss="0" a="0"></m><m x1="190" x2="346" y1="310"
y2="342" ss="0" a="1"></m><m x1="9" x2="159" y1="352" y2="381" ss="0" a="2"></m><m x1="193"
x2="342" y1="350" y2="382" ss="0" a="3"></m><m x1="25" x2="177" y1="56" y2="86" ss="1"
a="0"></m><m x1="26" x2="173" y1="118" y2="151" ss="1" a="1"></m><m x1="24" x2="176" y1="183"
y2="214" ss="1" a="2"></m><m x1="25" x2="174" y1="246" y2="279" ss="1" a="3"></m><c start="0"
stop="1"></c><c start="2" stop="0"></c><c start="1" stop="2"></c><c start="3" stop="3"></c>
QUESTION NO: 85
What is the first step to configuring the Wireless LAN Access Point 8750 after the access point (AP) is
powered on and connected to the Ethernet port of a switch configured with VLANs?
A. Ensure the AP and your PC are both connected to the same VLAN and install and launch the Wireless
Infrastructure Device Manager software on your PC
B. Connect your laptop PC to the second RJ-45 port on the AP and install and launch the Wireless
Infrastructure Device Manager software on your PC
C. Ensure the AP and your PC are both connected as untagged members of different VLANs and install
and launch the Wireless Infrastructure Device Manager software on your PC
D. Ensure the AP and your PC are connected as tagged members of different VLANs and install and
launch the Wireless Infrastructure Device Manager software on your PC
Answer: A
QUESTION NO: 86
What is a key alignment issue when installing an outdoor Wireless LAN (WLAN) panel antenna?
Answer: C
QUESTION NO: 87
Which wireless building-to-building bridge distance-related parameter must be set to ensure each
wireless bridge waits the appropriate period for a response from other wireless bridges?
Answer: C
QUESTION NO: 88
The 3Com 11a/b/g Wireless LAN Workgroup Bridge enables a laptop, PC or printer without built-in
wireless capability to connect to a wireless LAN.
A. True
B. False
Answer: A
QUESTION NO: 89
Every mobility domain should have a minimum of two seed switches assigned one main and one backup.
A. False
B. True
Answer: A
QUESTION NO: 90
Which three steps are required to configure a non-encrypted 3Com Wireless Distribution System?
(Choose three.)
A. Copy the access points (APs) to the Wireless Distribution System (WDS) configuration
C. Ensure all access points (APs) are configured for Managed Access Point (MAP) mode
F. Assign each access point (AP) the same Service Set ID (SSID) and radio channels
Answer: A,B,F
QUESTION NO: 91
How can the network administrator set the IP address and administrator password on a 3Com Access
Point?
B. Type the follow CLI command "Set user <name> password <p/w> admin"
C. Type the follow CLI commands "Set IPaddress <x.x.x.x>" and "Set user <name> password <p/w>
admin"
Answer: A
Match each 3Com Wireless Switch (WX) term with its description.
Answer: <m x1="14" x2="116" y1="317" y2="350" ss="0" a="0"></m><m x1="150" x2="252" y1="319"
y2="350" ss="0" a="1"></m><m x1="277" x2="380" y1="319" y2="350" ss="0" a="2"></m><m x1="8"
x2="111" y1="87" y2="117" ss="1" a="0"></m><m x1="2" x2="108" y1="157" y2="190" ss="1"
a="1"></m><m x1="5" x2="109" y1="229" y2="263" ss="1" a="2"></m><c start="2" stop="0"></c><c
start="0" stop="1"></c><c start="1" stop="2"></c>
QUESTION NO: 94
Which three are provided by the 3Com Wireless LAN Site Survey V2.x for discovered access points (APs)?
(Choose three.)
B. VLAN ID of each AP
C. IP address of each AP
Answer: A,E,F
QUESTION NO: 95
Which two are reasons a company may choose to use a building-to-building wireless bridge versus a
T1/E1 or fiber link? (Choose two.)
Answer: B,D
QUESTION NO: 96
To configure encryption on an access point (AP) that is part of a Wireless Distribution System (WDS), you
must configure each AP separately, using a wired-Ethernet connected computer.
A. True
B. False
Answer: A
QUESTION NO: 97
Which three Wireless LAN Access Point 8750 parameters are set using the 3Com Web Configuration
Management System "Advanced Setup Radio Setting" window? (Choose three.)
B. VLAN IDs
E. Administrator password
Answer: B,C,E,F
QUESTION NO: 99
You have taken a new job as the network administrator. You find a 3Com Wireless LAN Access Point
8750 on a shelf in the network supply closet. What should you do when you are unable to connect a
Wireless LAN Access Point 8750 because your predecessor has configured the access point (AP) with an
unknown username and password?
A. Reset the AP configuration to factory default by pressing the reset button for at least 15 seconds
B. Attach your PC directly to the RJ-45 port on the AP and telnet into the AP
C. Reset the AP to its default factory settings by opening the back of the AP and removing the battery for
at least 30 seconds
D. Use Windows Registry Editor to create and upload the following text to disable the AP security:
"HKEY_USERS\.DEFAULT\Software\3Com Corporation\EAPOL\UserEapInfo"
Answer: A
What is the optimal access point (AP) channel allocation configuration on a Wireless LAN (WLAN)?
A. Allow APs to automatically perform the hunting process to determine the best channels
Answer: C
A. Present
B. Properties
C. Show
D. Display
Answer: B
What can the 3Com Wireless LAN Switch Manager (3WXM) do when it discovers a wireless rogue
device?
A. Verify the IP address of the rouge device and send the information to a Syslog server
B. Verify the IP address of the rouge device and send the information to the management software,
which blocks future packets from the device
C. Flood the access point (AP), causing a Denial of Service (DoS) condition
D. Deactivate the access point (AP) and send a message to the network management software
Answer: C
Which best describes the information provided with the 3Com Wireless LAN Switch Manager (3WXM)
work order?
A. Information for the physical installation and software parameters, i.e., IP addresses, VLANs, channel
assignments, etc., of Managed Access Points (MAPs)
B. Information for the physical installation of Managed Access Points (MAPs), 3Com Wireless LAN
Controller/Switch initial setup configuration information and projected RSSI information of the 3Com
Wireless LAN Mobility System
C. Information for the physical installation of the 3Com Wireless LAN Mobility System
Answer: B
Match each 3Com OfficeConnect wireless client product with its features.
Answer: <m x1="11" x2="314" y1="359" y2="387" ss="0" a="0"></m><m x1="10" x2="314" y1="399"
y2="428" ss="0" a="1"></m><m x1="11" x2="313" y1="438" y2="469" ss="0" a="2"></m><m x1="11"
x2="313" y1="478" y2="510" ss="0" a="3"></m><m x1="11" x2="314" y1="292" y2="326" ss="1"
a="0"></m><m x1="10" x2="311" y1="221" y2="253" ss="1" a="1"></m><m x1="9" x2="314" y1="148"
y2="182" ss="1" a="2"></m><m x1="9" x2="314" y1="77" y2="108" ss="1" a="3"></m><c start="0"
stop="2"></c><c start="1" stop="0"></c><c start="2" stop="1"></c><c start="3" stop="3"></c>
Answer: <m x1="27" x2="346" y1="393" y2="424" ss="0" a="0"></m><m x1="27" x2="346" y1="433"
y2="464" ss="0" a="1"></m><m x1="27" x2="344" y1="473" y2="506" ss="0" a="2"></m><m x1="26"
x2="343" y1="328" y2="359" ss="1" a="0"></m><m x1="26" x2="345" y1="241" y2="271" ss="1"
a="1"></m><m x1="26" x2="343" y1="162" y2="190" ss="1" a="2"></m><m x1="27" x2="345" y1="79"
y2="110" ss="1" a="3"></m><c start="0" stop="2"></c><c start="1" stop="0"></c><c start="2"
stop="1"></c>
Answer: B,C,D
Many access points (APs) are set up with a default configuration, known as "open system" or "open
system authentication," so any station can associate and connect.
A. False
B. True
Answer: B
Wireless LAN (WLAN) IEEE 802.11a Turbo Mode bonds two channels together for up to 108 Mbps data
rates.
A. True
B. False
Answer: A
Which three types of wireless devices may be detected as rogues by the 3Com Wireless LAN Switch
Manager (3WXM)? (Choose three.)
Answer: B,D,E
The network administrator can draw or import a JPEG or AutoCAD building floor plan using the 3Com
Wireless LAN Switch Manager (3WXM).
A. True
B. False
Answer: A
QUESTION NO: 111
Which three steps are required to configure a non-encrypted 3Com Wireless Distribution System?
(Choose three.)
A. Assign each access point (AP) the same Service Set ID (SSID) and radio channels
B. Copy the access points (APs) to the Wireless Distribution System (WDS) configuration
D. Ensure all access points (APs) are configured for Managed Access Point (MAP) mode
Answer: A,B,E
Which three are features of a Wireless Distribution System (WDS)? (Choose three.)
C. Supported on the Wireless LAN Access Point 7250 and Wireless LAN Access Point 8xx0 family
F. Uses Virtual Router Redundancy Protocol (VRRP) to manage redundant wireless paths
Answer: B,C,D
Which parameters must be completed to set up a 3Com access point (AP) as a non-restrictive Virtual
Access Point (VAP)?
Answer: C
Which three are features supported on the OfficeConnect ADSL Wireless 11g Firewall Router and the
3Com OfficeConnect Wireless 11g Cable/DSL Router? (Choose three.)
E. VPN termination
An advantage of using radio frequency (RF) signals for a Wireless LAN (WLAN) is that an RF signal can
pass through any object without interference (i.e., walls, concrete, steel, etc.).
A. False
B. True
Answer: A
Any one of the VLAN IP addresses assigned to a Wireless LAN Switch/Controller can be used for its
management communications.
A. False
B. True
Answer: B
Which two are performed by the 3Com Wireless LAN Switch Manager (3WXM), during the Compute and
Place MAPs process of network planning, to determine the number of Managed Access Points (MAPs)
for an area? (Choose two.)
Answer: B,D
B. It enables Jumbo Frames on the port, providing higher data throughput on the link
C. It immediately puts a port into the STP forwarding state, preventing an application from possibly
timing out
D. It configures all the ports for 1,000 Mbps full duplex, providing maximum throughput
Answer: C
Match each 3Com Wireless Switch (WX) IP service with its description.
Answer: <m x1="20" x2="182" y1="420" y2="451" ss="0" a="0"></m><m x1="21" x2="180" y1="461"
y2="492" ss="0" a="1"></m><m x1="22" x2="182" y1="502" y2="531" ss="0" a="2"></m><m x1="21"
x2="179" y1="539" y2="571" ss="0" a="3"></m><m x1="21" x2="178" y1="581" y2="608" ss="0"
a="4"></m><m x1="30" x2="187" y1="253" y2="282" ss="1" a="0"></m><m x1="28" x2="186" y1="319"
y2="350" ss="1" a="1"></m><m x1="28" x2="186" y1="187" y2="220" ss="1" a="2"></m><m x1="32"
x2="186" y1="124" y2="158" ss="1" a="3"></m><m x1="29" x2="188" y1="57" y2="94" ss="1"
a="4"></m><c start="1" stop="4"></c><c start="0" stop="3"></c><c start="3" stop="2"></c><c
start="2" stop="0"></c><c start="4" stop="1"></c>
QUESTION NO: 121
Which three are features of 3Com Dynamic Security Link? (Choose three.)
D. Local and remote access point (AP) authentication and encryption support
Answer: A,C,E
Match each 3Com OfficeConnect wireless client product with its features.
Answer: <m x1="18" x2="317" y1="362" y2="391" ss="0" a="0"></m><m x1="18" x2="319" y1="402"
y2="433" ss="0" a="1"></m><m x1="16" x2="319" y1="441" y2="473" ss="0" a="2"></m><m x1="18"
x2="320" y1="482" y2="511" ss="0" a="3"></m><m x1="12" x2="321" y1="297" y2="330" ss="1"
a="0"></m><m x1="17" x2="320" y1="225" y2="258" ss="1" a="1"></m><m x1="15" x2="320" y1="157"
y2="186" ss="1" a="2"></m><m x1="18" x2="319" y1="81" y2="114" ss="1" a="3"></m><c start="1"
stop="3"></c><c start="2" stop="2"></c><c start="3" stop="1"></c><c start="0" stop="0"></c>
Answer: <m x1="17" x2="333" y1="407" y2="438" ss="0" a="0"></m><m x1="15" x2="333" y1="456"
y2="487" ss="0" a="1"></m><m x1="15" x2="334" y1="505" y2="534" ss="0" a="2"></m><m x1="16"
x2="333" y1="552" y2="582" ss="0" a="3"></m><m x1="16" x2="334" y1="327" y2="358" ss="1"
a="0"></m><m x1="14" x2="334" y1="238" y2="273" ss="1" a="1"></m><m x1="16" x2="335" y1="158"
y2="189" ss="1" a="2"></m><m x1="15" x2="333" y1="77" y2="112" ss="1" a="3"></m><c start="1"
stop="3"></c><c start="0" stop="2"></c><c start="2" stop="0"></c><c start="3" stop="1"></c>
QUESTION NO: 124
Which two are performed by the 3Com Wireless LAN Switch Manager (3WXM), during the Compute and
Place MAPs process of network planning, to determine the number of Managed Access Points (MAPs)
for an area? (Choose two.)
Answer: A,C
Which three are standards/limitations when you are creating a mobility domain on the 3Com Wireless
LAN Switch/Controller (WX)? (Choose three.)
Answer: B,C,E
QUESTION NO: 126 DRAG DROP
Answer: <m x1="11" x2="97" y1="317" y2="351" ss="0" a="0"></m><m x1="108" x2="195" y1="317"
y2="347" ss="0" a="1"></m><m x1="202" x2="290" y1="318" y2="350" ss="0" a="2"></m><m x1="10"
x2="97" y1="359" y2="391" ss="0" a="3"></m><m x1="106" x2="195" y1="359" y2="391" ss="0"
a="4"></m><m x1="19" x2="107" y1="264" y2="294" ss="1" a="0"></m><m x1="19" x2="105" y1="215"
y2="245" ss="1" a="1"></m><m x1="19" x2="106" y1="167" y2="198" ss="1" a="2"></m><m x1="20"
x2="104" y1="119" y2="149" ss="1" a="3"></m><m x1="20" x2="106" y1="69" y2="102" ss="1"
a="4"></m><c start="1" stop="4"></c><c start="2" stop="3"></c><c start="0" stop="2"></c><c
start="4" stop="1"></c><c start="3" stop="0"></c>
QUESTION NO: 127
Which functionality is transferred from 3Com Access Points (APs) to the 3Com Wireless LAN
Controller/Switch, creating Fit APs or Managed Access Points (MAPs) with the 3Com Wireless LAN
Mobility System?
Answer: A
Which best describes the information provided with the 3Com Wireless LAN Switch Manager (3WXM)
work order?
B. Information for the physical installation of the 3Com Wireless LAN Mobility System
C. Information for the physical installation of Managed Access Points (MAPs), 3Com Wireless LAN
Controller/Switch initial setup configuration information and projected RSSI information of the 3Com
Wireless LAN Mobility System
D. Information for the physical installation and software parameters, i.e., IP addresses, VLANs, channel
assignments, etc., of Managed Access Points (MAPs)
Answer: C
QUESTION NO: 129
What is the optimal access point (AP) channel allocation configuration on a Wireless LAN (WLAN)?
D. Allow APs to automatically perform the hunting process to determine the best channels
Answer: B
Which three are 3Com Wireless LAN Switch Manager (3WXM) network planning functions? (Choose
three.)
C. Define the RF model and the coverage areas for the floor
Answer: A,C,E
QUESTION NO: 131 DRAG DROP
Match each Radio Frequency (RF) propagation issue with its description.
Answer: <m x1="9" x2="159" y1="313" y2="344" ss="0" a="0"></m><m x1="192" x2="344" y1="312"
y2="345" ss="0" a="1"></m><m x1="8" x2="158" y1="353" y2="384" ss="0" a="2"></m><m x1="193"
x2="343" y1="351" y2="384" ss="0" a="3"></m><m x1="266" x2="269" y1="365" y2="366" ss="0"
a="4"></m><m x1="22" x2="177" y1="248" y2="280" ss="1" a="0"></m><m x1="25" x2="177" y1="185"
y2="217" ss="1" a="1"></m><m x1="25" x2="174" y1="121" y2="152" ss="1" a="2"></m><m x1="23"
x2="176" y1="54" y2="91" ss="1" a="3"></m><c start="2" stop="3"></c><c start="0" stop="2"></c><c
start="1" stop="1"></c><c start="3" stop="0"></c><c start="3" stop="0"></c>
QUESTION NO: 132
How can the network administrator set the IP address and administrator password on a 3Com Access
Point?
A. Type the follow CLI command "Set user <name> password <p/w> admin"
B. Type the follow CLI commands "Set IPaddress <x.x.x.x>" and "Set user <name> password <p/w>
admin"
Answer: C
Which three are standards/limitations when you are creating a mobility domain on the 3Com Wireless
LAN Switch/Controller (WX)? (Choose three.)
Answer: A,B,C
Answer: <m x1="8" x2="107" y1="366" y2="395" ss="0" a="0"></m><m x1="117" x2="222" y1="366"
y2="398" ss="0" a="1"></m><m x1="230" x2="332" y1="367" y2="397" ss="0" a="2"></m><m x1="342"
x2="444" y1="368" y2="398" ss="0" a="3"></m><m x1="6" x2="107" y1="294" y2="325" ss="1"
a="0"></m><m x1="7" x2="108" y1="223" y2="253" ss="1" a="1"></m><m x1="7" x2="113" y1="150"
y2="183" ss="1" a="2"></m><m x1="10" x2="113" y1="79" y2="111" ss="1" a="3"></m><c start="0"
stop="0"></c><c start="1" stop="2"></c><c start="2" stop="3"></c><c start="3" stop="1"></c>
D. Weatherproof enclosure
Answer: A,C,E
You have taken a new job as the network administrator. You find a 3Com Wireless LAN Access Point
8750 on a shelf in the network supply closet. What should you do when you are unable to connect a
Wireless LAN Access Point 8750 because your predecessor has configured the access point (AP) with an
unknown username and password?
A. Reset the AP to its default factory settings by opening the back of the AP and removing the battery for
at least 30 seconds
B. Attach your PC directly to the RJ-45 port on the AP and telnet into the AP
C. Use Windows Registry Editor to create and upload the following text to disable the AP security:
"HKEY_USERS\.DEFAULT\Software\3Com Corporation\EAPOL\UserEapInfo"
D. Reset the AP configuration to factory default by pressing the reset button for at least 15 seconds
Answer: D
Which parameters must be completed to set up a 3Com access point (AP) as a non-restrictive Virtual
Access Point (VAP)?
Answer: B
Every mobility domain should have a minimum of two seed switches assigned one main and one backup.
A. True
B. False
Answer: B
D. Defines the ability to fine tune Wireless LAN configuration at the Physical (PHY) Layer to comply with
country-specific rules
Answer: D
Match each 3Com Wireless Switch (WX) term with its description.
Answer: <m x1="13" x2="118" y1="319" y2="351" ss="0" a="0"></m><m x1="151" x2="253" y1="320"
y2="352" ss="0" a="1"></m><m x1="278" x2="382" y1="319" y2="353" ss="0" a="2"></m><m x1="6"
x2="109" y1="232" y2="261" ss="1" a="0"></m><m x1="6" x2="109" y1="160" y2="191" ss="1"
a="1"></m><m x1="10" x2="113" y1="86" y2="119" ss="1" a="2"></m><c start="2" stop="2"></c><c
start="0" stop="1"></c><c start="1" stop="0"></c>
Choose the three features supported by the 11g 54Mbps Wireless LAN Outdoor Building-to-Building
Bridge. (Choose three.)
A. Weatherproof enclosure
Answer: A,B,D
Which describes the 3Com Receiver Signal Strength Indicator (RSSI) access point (AP) implementation?
B. AP displays neighbor AP's signal strength and quality as a value from 0 to 255
The 3Com Wireless LAN Controller WX4400 provides high-bandwidth, centralized control for up to 144
directly attached managed access points (MAPs).
A. True
B. False
Answer: B
What is the first step a wireless station performs as it attempts to access a wireless network?
B. Authentication
C. Beaconing
Answer: A
B. Beaconing
C. Authentication
Answer: A
What is the process for determining the best installation design of a Wireless LAN (WLAN)?
A. Facility walk-through
B. Network discovery
C. Site survey
D. WLAN analyzer
Answer: C
Match each 3Com Wireless Switch (WX) term with its description.
Answer: <m x1="10" x2="114" y1="317" y2="348" ss="0" a="0"></m><m x1="147" x2="250" y1="317"
y2="350" ss="0" a="1"></m><m x1="275" x2="378" y1="318" y2="350" ss="0" a="2"></m><m x1="8"
x2="110" y1="86" y2="120" ss="1" a="0"></m><m x1="4" x2="108" y1="158" y2="188" ss="1"
a="1"></m><m x1="4" x2="105" y1="229" y2="261" ss="1" a="2"></m><c start="2" stop="0"></c><c
start="0" stop="1"></c><c start="1" stop="2"></c>
Which two are performed by the 3Com Wireless LAN Switch Manager (3WXM), during the Compute and
Place MAPs process of network planning, to determine the number of Managed Access Points (MAPs)
for an area? (Choose two.)
Answer: B,C
Answer: C
A. Static routes to forward traffic passing through the WX to a specific IP router, if the traffic is not on a
local VLAN or subnet
B. Static routes to forward traffic generated by the WX to a specific IP router, if the traffic is not on a
local VLAN or subnet
C. Static routes to forward traffic passing through the WX to a specific IP router, if the traffic is on a local
VLAN or subnet
D. Static routes to forward traffic generated by the WX to a specific IP router, if the traffic is on a local
VLAN or subnet
Answer: B
Which two are features of a Wireless LAN (WLAN) Infrastructure Basic Service Set? (Choose two.)
A. Members communicate directly with each other within the service area
B. Management and control of the service area is performed by the access point (AP)
C. Only stations exist in the service area and no access point (AP) is used
D. Created when two or more Basic Service Sets are connected together
Answer: A,B
Which statement is true for Wireless LAN (WLAN) data and throughput rates?
A. Actual data throughput on a WLAN is about 25% of the defined throughput rate
B. Data rates drop as the distance to the access point (AP) decreases
C. Data rates on an IEEE 802.11a/g WLAN are not affected by distance from the access point (AP)
D. Data rates drop as the distance to the access point (AP) increases
Answer: D
QUESTION NO: 154
Which best describes the purpose of the 3Com Wireless LAN Switch Manager (3WXM) "upload"
command?
A. To perform an error check on a configuration file, then deploy the file from 3WXM to a 3Com
Wireless LAN Switch/Controller
B. To load a configuration file from a 3Com Wireless LAN Switch/Controller into 3WXM, perform an error
check on the file and place the unit into the network plan
D. To perform an error check on a configuration file, then load the file from a 3Com Wireless LAN
Switch/Controller to the 3WXM
Answer: B
Many access points (APs) are set up with a default configuration, known as "open system" or "open
system authentication," so any station can associate and connect.
A. True
B. False
Answer: A
QUESTION NO: 156
The network administrator can draw or import a JPEG or AutoCAD building floor plan using the 3Com
Wireless LAN Switch Manager (3WXM).
A. False
B. True
Answer: B
You have taken a new job as the network administrator. You find a 3Com Wireless LAN Access Point
8750 on a shelf in the network supply closet. What should you do when you are unable to connect a
Wireless LAN Access Point 8750 because your predecessor has configured the access point (AP) with an
unknown username and password?
A. Reset the AP to its default factory settings by opening the back of the AP and removing the battery for
at least 30 seconds
B. Reset the AP configuration to factory default by pressing the reset button for at least 15 seconds
C. Use Windows Registry Editor to create and upload the following text to disable the AP security:
"HKEY_USERS\.DEFAULT\Software\3Com Corporation\EAPOL\UserEapInfo"
D. Attach your PC directly to the RJ-45 port on the AP and telnet into the AP
Answer: B
Which two are functions of the 3Com Wireless LAN Switch Manager (3WXM) "deploy" command?
A. Sends a configuration file from 3WXM to a 3Com Managed Access Point (MAP)
C. Synchronizes configuration information between the 3WXM and a 3Com Wireless LAN
Switch/Controller
E. Allows a Wireless LAN Switch/Controller to be drawn into a Network Plan Mobility Domain
Answer: C,D
Drag each 3Com Wireless LAN Mobility System product to the set of features it supports.
Answer: <m x1="21" x2="341" y1="481" y2="510" ss="0" a="0"></m><m x1="20" x2="337" y1="520"
y2="551" ss="0" a="1"></m><m x1="19" x2="337" y1="561" y2="590" ss="0" a="2"></m><m x1="20"
x2="339" y1="416" y2="448" ss="1" a="0"></m><m x1="21" x2="338" y1="329" y2="359" ss="1"
a="1"></m><m x1="20" x2="341" y1="241" y2="270" ss="1" a="2"></m><m x1="22" x2="338" y1="159"
y2="189" ss="1" a="3"></m><m x1="22" x2="340" y1="81" y2="112" ss="1" a="4"></m><c start="0"
stop="2"></c><c start="1" stop="4"></c><c start="2" stop="0"></c>
QUESTION NO: 162
Answer: A