Professional Documents
Culture Documents
PF 206SMEng
PF 206SMEng
PF 206SMEng
PF-206
SERVICE MANUAL
10794
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
CONTENTS
GENERAL, MECHANICAL/ELECTRICAL
1. SPECIFICATIONS ........................................................................................... M-1
2. COMPONENT IDENTIFICATION .................................................................... M-1
3. CROSS-SECTIONAL VIEW ............................................................................ M-2
4. DRIVE SYSTEM .............................................................................................. M-2
5. ELECTRICAL PARTS LAYOUT ...................................................................... M-3
6. VERTICAL TRANSPORT SECTION ............................................................... M-4
7. PAPER TAKE-UP/FEEDING SECTION .......................................................... M-5
7-1. Paper Take-Up Mechanism ..................................................................... M-5
(1) Paper Take-Up Mechanism ............................................................. M-5
(2) Paper Separating Mechanism ......................................................... M-6
(3) Paper Pressure Releasing Mechanism ........................................... M-7
(4) Paper Take-Up Roll Retraction Mechanism .................................... M-7
7-2. Paper Take-Up Control ............................................................................ M-8
(1) Paper Take-Up Motor Control ......................................................... M-8
(2) Paper Take-Up Retry Control .......................................................... M-8
(3) Paper Take-Up Interval Control (30 cpm Copier Only) .................... M-9
(4) Double Feed Paper Take-Up Control (30 cpm Copier Only) ........... M-9
7-3. Fixed Drawer ........................................................................................... M-10
7-4. Drawer-in-Position Detection ................................................................... M-10
7-5. Drawer Paper Lift-Up Mechanism ............................................................ M-11
7-6. Paper Empty Detection ............................................................................ M-13
7-7. Paper Level Detection (30 cpm Copier Only) .......................................... M-14
7-8. Cabinet Paper Dehumidifying Heater (option) ......................................... M-15
DIS/REASSEMBLY, ADJUSTMENT
1. DISASSEMBLY ............................................................................................... D-1
1-1. Removal of Exterior Parts ........................................................................ D-1
1-2. Removal of the Guide Plates and Cover Plates ...................................... D-2
1-3. Removal of Paper Take-Up Roll and Feed Roll Assy from Drawer ......... D-2
1-4. Disassembly of Paper Take-Up Roll/Feed Roll Assy ............................... D-3
1-5. Removal of Separator Roll Assy .............................................................. D-4
1-6. Cleaning of Paper Take-Up Roll, Feed Roll and Separator Roll .............. D-5
1-7. Cleaning of Transport Roller .................................................................... D-5
2. ADJUSTMENT ................................................................................................. D-6
2-1. Adjustment of 3rd and 4th Drawer Reference Position ............................ D-6
2-2. Adjustment of Vertical Transport Timing Belt .......................................... D-7
i
FrameMaker Ver.5.5(PC) PF-112 OPTION FOR EP1054/EP1085/EP2030
98.06.08
GENERAL,
MECHANICAL/
ELECTRICAL
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
1 SPECIFICATIONS
2 COMPONENT IDENTIFICATION
1 2
10 3
4
9
1174M016AA
8 7 6 5
M-1
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
3 CROSS-SECTIONAL VIEW
1 2
3
4
14
5
6
9
13 12 11 4425M016AA
10
4 DRIVE SYSTEM
4425M017AA
M-2
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
4425M018AA
M-3
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
Vertical Transport
Vertical Transport Roller 1
Motor M21
4425M010AA
4479T51MCB
M-4
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
Take-Up Roll
Feed Roll
Separator Roll
M-5
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
Driven or stationary
<Double Feeding>
• Since the coefficient of friction between the
top side of the first sheet of paper and the
Feed Roll Feed Roll is greater than that between the
first and second sheets of paper, the first
1st Sheet of sheet of paper is fed into the copier by the
Paper Feed Roll.
Since the friction coefficient between the
2nd Sheet of second sheet of paper and the Separator
Paper Roll is greater than that between the first
and second sheet of paper, the Separator
4425M013AA
Separator Roll Roll is not driven and holds the second
sheet of paper.
Stopped
M-6
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
Feed Roll
4444M004AA
Drawer Pressure spring
Take-Up Roll/Feed
Front
Roll Assy
Pressure
Release Lever
Rear 4425M015AA
M-7
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
4479T52MCB
4479T53MCB
M-8
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
(4) Double Feed Paper Take-Up Control (30 cpm Copier Only)
• Even if the Paper Take-Up Roll takes up two sheets of paper at one time, the double feed
paper take-up control uses the second sheet of paper for the next copy cycle without
causing a paper misfeed. It eliminates a paper misfeed that would otherwise result when
two sheets of paper are taken up at once.
• If the second sheet of paper is stationary blocking Paper Take-Up Sensor when the trail-
ing edge of the first sheet of paper moves past Vertical Transport Sensor, the copier
determines that it is a double feed condition and provides double feed control.
• If, however, the second sheet of paper has reached the Vertical Transport Roller, the dou-
ble feed control is not provided since the paper is fed further into the copier by the Verti-
cal Transport Roller. This could result in a paper misfeed or the second sheet of paper
being fed through the copier with the first one.
Paper Path
4444M040AA
M-9
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
Rear
3rd/4th Drawer
Set Sensor
Front
PC25, 26
1174M018AA
M-10
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
3rd/4th Drawer
Paper Lift-Up
Motor M24/25
Front
4425M004AA
When Drawer is Slid in • The Paper Lifting Arm further raises the
paper after the top sheet of paper is
3rd/4th Drawer Paper Lift-Up pressed against the Paper Take-Up Roll.
Sensor (PC19/PC23) As the light blocking plate blocks the Paper
Lift-Up Sensor (goes low), the Paper Lift-Up
Motor stops.
4425M005AA
4479T54MCB
M-11
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
During Copying
• As sheets of paper are used, the Paper
Take-Up Roll lowers accordingly, unblocking
the Drawer Paper Lift-Up Sensor (goes
high).
4425M006AA
4425M005AA
• Energizing and deenergizing of the Paper Lift-Up Motor keeps constant the pressure
between the Paper Take-Up Roll and paper regardless of the height of the paper stack.
M-12
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
4425M009AA
M-13
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
• 50 to 200 sheets
1134M059AA
• 500 sheets up
1134M062AA
1134M020AA
M-14
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
M-15
FrameMaker Ver.5.5(PC) PF-112 OPTION FOR EP1054/EP1085/EP2030
98.06.08
DIS/REASSEMBLY,
ADJUSTMENT
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
1 DISASSEMBLY
7
1
2
6
11
1174D003AA 4425D001AA
10
8
5 4 9
3
D-1
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
4425D003AA
1-3. Removal of Paper Take-Up Roll and Feed Roll Assy from Drawer
4479D001AA
4425D004AA
4425D005AA
D-2
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
4425D006AA
NOTE
To reinstall the Paper Take-Up Roll/Feed Roll Assy:
1. Close the drawer
2. Engage the shaft coupling with the pin of the Cabi-
net
3. Insert the assy. bracket above the Pressure
Release Lever
4425D007AA 4. Hold down the torsion spring and install the assy.
NOTE
Keep the lock pin for later use.
4479D002AA
(5)
(4)
(1)
(3)
4479D003AA
(2)
D-3
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
4479D004AA
4479D005AA
4479D001AA
4479D006AA
D-4
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
4444M006AA
4425D017AA
D-5
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
2 ADJUSTMENT
1074D089
1139D027AA
Tighten the 4. If the copied line deviates from the reference line,
screws pull out the 3rd drawer. Loosen 3 screws on the
adjusting plate and then move the plate forward or
backward to adjust the line position.
NOTE
If copied width A<18 mm, move the adjusting plate
toward the rear.
1139U100A If copied width A>22 mm, move the adjusting plate
toward the front.
1139U037AA
D-6
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
D-7
FrameMaker Ver.5.5(PC) PF-112 OPTION FOR EP1054/EP1085/EP2030
98.06.08
MISFEED
DETECTOIN &
MALFUNCTION
DETECTION
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
1 MISFEED DETECTION
4425T201AA
T-1
FrameMaker Ver.5.5(PC) PF-206 OPTION FOR EP1054/EP1085/EP2030
98.06.08
2 MALFUNCTION DETECTION
T-2