Professional Documents
Culture Documents
Goodco Z Tech Sliding Bearings
Goodco Z Tech Sliding Bearings
Goodco Z Tech Sliding Bearings
EIEAFIINGIS-
W TS slidingbearingconsistsof a top steel plateunderwhich is
The multidirectional
weldeda polishedstainlesssteel sheet.The top face can be flat or bevelled.The
@ I
bottomcomponentconsistsof a steel platewith the top surfacefaced with a PTFE
disc recessedapproximatelyhalf its thicknessinto the steel.
TS
FEATURES MATERIAL
- No verticaldeflection SteefComponents:All steelplatesconformto CSAG40.21-260W(ASTMA-36),
underload -300Wor -350A(ASTMA-588).Othersteelgradescan alsobe supplieddepend-
- Verylowslidingfriction ing on specificrequirements
or availability.
- Unlimitedmovement capacity
- Seizure-freemovement StainlessSteel: ToASTMA-167,type304.The surfacefinishin contactwiththe
- No rotation PTFE,when measuredin accordance with CSA standard895, shall not be
- Lowcostmaintenance greaterthan0.25pm arithmetic
average.
- Simpleto install The PTFE discs are fabricatedfrom pure
PTFE (Polytetrafluoroethylene):
- No movingparts unfilledsheetsandthe PTFEusedfor the guidebarsfrom 15"/"glassfilled
strips.
- Corrosionprotection All PTFEmaterialis chemically
etched on one facefor bonding.
AnchorSystem: Fusionweldedstudsconformto ASTMA-108.Steelpinscon-
APPLICATION form to ASTMA-36,A-588or CSA G40.21-300W.Connectingboltsconformto
ASTMA-325.
shortsteelspan,
Pipeline,
machinery,etc. Steel Finish: Exposedsteelsuffacesare ztncmetallizedaccordingto CSA G-
189 (AWSC2.2-67),minimumthickness175 microns.The use a primerand
polyurethane is recommended.
sealersystemoverthe zincmetallizing Epoxyor
vinylcoatingsystemscan alsobe used.
-PTFEGiUItrlESi-
The TG guideunit is designedto restrainthe horizontalmovementof a struc-
ture. lt carriesno verticalload and will allowa certainverticalmovementwithin
the limitsof the designedclearance.
The top componentconsistsof a top steel plate underwhich is weldeda steel
rectangularguide bar.The two verticaledgesof the guide bar are facedwith a
PTFE strip recessedapproximatlyhalf its thicknessinto the steel.The bottom
componentconsistsof a steel plate on top of which is welded two (2) steel
guidebars.To each insideverticalface of the guidebars is weldeda polished
stainlesssteelstrip.lf required,the two (2) bottomguidebars can be reinforced
with the additionof verticalstiffenerplates.
FEATURES MATERIAL
- Very low slidingfriction Steef Components: All steel platesconformto CSA G40.21-260W(ASTMA-
- Unlimitedmovementcapacity 36), -300W or -350A (ASTM A-588).Other steel gradescan also be supplied
- Seizure-freemovement dependingon specificrequirementsor availability.
- Low cost maintenance
- No rotation Stainless Steel: To ASTM A-167,type 304. The surfacefinish in contactwith
- Simpleto install the PTFE,when measuredin accordancewith CSA standard895, shall not be
- No movingparts greaterthan 0.25 pm arithmeticaverage.
- Corrosionprotection PTFE (Polytetrafluoroethylene):The PTFE discs are fabricatedf rom pure
unfilledsheets and the PTFE used for the guide bars from 15% glassfilled
APPLIGATION strips.All PTFEmaterialis chemicallyetchedon one facefor bonding.
Anchor System: Fusionweldedstuds conformto ASTM A-108. Steel pins
Bridges,overpasses,stadium
conformto ASTM A-36, A-588 or CSA G40.21-300W.Connectingbolts con-
and/or arenaroofconnections.
form to ASTM A-325.
etc.
Steel Finish : Exposedsteelsurfacesare zinc metallizedaccordingto CSA G-
189 (AWSC2.2-67),minimumthickness175 microns.The use a primerand
polyurethanesealersystemover the zinc metallizingis recommended.Epoxy
or vinylcoatingsystemscan also be used.