Professional Documents
Culture Documents
LOCTITE 603 en - GL
LOCTITE 603 en - GL
LOCTITE® 603
December-2009
LOCTITE® 603 is designed for the bonding of cylindrical fitting Cure Speed vs. Bond Gap
The rate of cure will depend on the bondline gap.The following
parts, particularly where consistently clean surfaces cannot be
graph shows shear strength developed with time on steel pins
assuredThe product cures when confined in the absence of air and collars at different controlled gaps and tested according to
between close fitting metal surfaces and prevents loosening ISO 10123
and leakage from shock and vibrationTypical applications
include retaining roller bearings or oil impregnated bushings 100
% of Full Strength on Steel
into housings
75
m
NSF International
5m
m
Registered to NSF Category P1 for use as a sealant where
m
0.0
15
there is no possibility of food contact in and around food 50
0.
mm
processing areas. Note: This is a regional approval. Please
contact your local Technical Service Center for more
0.2
information and clarification. 25
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 603, December-2009
50
Activator SF 7471™
Hot Strength
25 Tested at temperature
Activator SF 7649™ 100
% Strength @ 22 °C
0
1min 5min10min 30min 1h 3h 6h 24h 72h 75
Cure Time
50
Cure Speed vs. Temperature
The rate of cure will depend on the temperatureThe graph
below shows the shear strength developed with time at 25
different temperatures on steel pins and collars and tested
according to ISO 10123
0
100 0 50 100 150
% of Full Strength on Steel
Temperature, °C
75 Heat Aging
°C
°C
5°
22
50 125
120 °C
% Strength @ 22 °C
25 100
75
0
1min 5min10min 30min 1h 3h 6h 24h 72h
Cure Time 50
150 °C
TYPICAL PROPERTIES OF CURED MATERIAL 25
Physical Properties:
Coefficient of Thermal Expansion, 80×10-6 0
ISO 11359-2, K-1 0 1000 2000 3000 4000 5000
Coefficient of Thermal Conductivity, ISO 8302, 0.1 Exposure Time, hours
W/(m·K)
Specific Heat, kJ/(kg·K) 0.3 Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 23 °C.
% of initial strength
Environment °C 100 h 500 h 1000 h
TYPICAL PERFORMANCE OF CURED MATERIAL Motor oil (MIL-L-46152) 125 100 100 100
Adhesive Properties Unleaded Petrol 22 100 90 85
After 24 hours @ 22 °C Brake fluid 22 100 90 80
Compressive Shear Strength, ISO 10123: Water/glycol 50/50 87 100 90 80
Steel pins and collars N/mm² ≥22.5 Ethanol 22 100 100 75
(psi) (3,260)
Acetone 22 90 90 90
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 603, December-2009
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 603, December-2009
Trademark usage
Except as otherwise noted, all trademarks in this document are
trademarks of Henkel Corporation in the U.S. and elsewhere. ®
denotes a trademark registered in the U.S. Patent and Trademark
Office.
Reference 0.4
For the most direct access to local sales and technical support visit: www.henkel.com/industrial