Download as doc, pdf, or txt
Download as doc, pdf, or txt
You are on page 1of 26

COURSE: BOEING 777-200/200ER/300/300ER B1 - PHASE 10 – AV EXT.

Date: _______________________________ Course Code: 007/2008

Required TOPIC Subject Level No. of Actual No of No. of Question Numbers selected
Subject Duration Questions Questions in Questions
Level required in the bank to be
the bank picked
2 ATC/TCAS 2 1 4 0
2 5 3
3 3 0
TOTAL 12 3
2 WEATHER RADAR 1 1 4 0
2 7 2
3 1 0
TOTAL 12 2
2 FLIGHT INTERPHONE/ 2 1 8 0
SERVICE INTERPHONE/ 2 10 3
GROUND CREW CALL 3 0 0
TOTAL 18 3
2 VHF/HF 2 1 4 0
2 8 2
3 1 0
TOTAL 13 3
2 SELCAL/ELT 2 1 4 0
2 5 2
3 0 0
TOTAL 9 2
2 CABIN INTERPHONE 2 1 0 0
2 5 2
3 0 0
TOTAL 5 2
Required TOPIC Subject Level No. of Actual No of No. of Question Numbers selected
Subject Duration Questions Questions in Questions
Level required in the bank to be
the bank picked
2 PAS/ SATCOM/DCMF/EFB/ 5 1 16 2
FDEVSS/CVR/PC PWR 2 12 5
3 2 0
TOTAL 30 7
2 IFE (MAS 2000E) 5 1 8 1
2 16 4
3 0 0
TOTAL 24 5
2 IFE (MAS 3000I) 3 1 8 0
2 8 3
3 0 0
TOTAL 16 3
TOTAL 139 30

I hereby confirm that the question levels selected for the examination meet the requirements of EASA Part 66 Appendix 3.

Examiner’s Signature: __________________________

Level Total # of Seconds Total Time


Questions selected
1 x 75
2 x 75
3 x120
Time Required for the
Examination
BOEING 777-200/200ER/300/300ER B1
COURSE EXAMINATION

PHASE - X

MASTER

ATA 34 – ATC/TCAS

L1 Q.1 The ATC antennas are located:

a] on top of the fuselage


b] at the bottom of the fuselage
 c] on the top and the bottom of the fuselage

L1 Q.2 The transponder panel is on the:

 a] aisle stand panel


b] overhead panel
c] main instrument panel

L1 Q.3 TCAS is:

a] a ground station
 b] an airborne system
c] a part of TMCS - in full not abbreviated

L1 Q.4 The TCAS helps the flight crew and air traffic control to:

 a] maintain safe air traffic separation


b] measure the distance from the airplane to the ground
c] alert the flight crew of an unsafe condition when near terrain

L2 Q.5 How are the ATC antennas interfaced to the transponders?

a] the top antenna is connected to the Left ATC, the bottom antenna to the Right
ATC
 b] both antennas are connected to the selected ATC
c] the top antenna is connected to both ATC’s and the bottom antenna is in
standby.
L2 Q.6 The ATC/Mode S Transponder supplies a 24 bit unique airplane identification code to:

a] SELCAL decoder
b] flight deck displays (PFDs)
 c] TCAS computer

L2 Q.7 The ATC coax relays are located:

a] on the top and the bottom fuselage near the antenna


 b] at the E1 and E2 racks in the MEC
c] in the cockpit

L2 Q.8 TCAS Resolution Advisories (RA) are displayed on:

 a] the attitude display of the PFD


b] the vertical speed indication of the PFD
c] the ND in the plan mode

L2 Q.9 Suppression signals are sent from the DME Interrogator to the:

a] ATC and Radio Altimeter


b] ATC and Weather Radar Transmitter Receiver unit
 c] ATC and TCAS computer units

L3 Q.10 All tests for the ATC/mode S transponder must be done from the:

a] MCDU
 b] MAT or a PMAT
c] ATC/TCAS Control panel

L3 Q.11 What happens to TCAS AUDIO ADVISORIES when there is a Ground Proximity
Warning System warning or alert?

 a] The TCAS Audio Advisories stop


b] The TCAS Audio Advisories mix with the Ground Proximity Warning System
Audio warnings
c] The Ground proximity warnings stop to give priority for the TCAS Audio
advisories

L3 Q.12 The red advisories that show on the attitude display:

 a] tells the flight crew to avoid this area


b] tells the flight crew to increase the rate of climb
c] is shown for an RA when the function selector on the transponder panel is in the
XPDR, TA/RA or TA position
ATA 34 - WEATHER RADAR

L1 Q.1 The weather radar system supplies visual indications of:

a] weather conditions
b] land contours
 c] weather conditions and land contours

L1 Q.2 The Weather radar returns show in four different colors on the:

 a] ND only
b] PFD only
c] EICAS only

L1 Q.3 The weather radar antenna is located:

a] on top of the fuselage


 b] inside the nose radome
c] on the forward nose wheel well door

L1 Q.4 The weather radar panel is on the:

a] main instrument panel


b] glareshield
 c] aisle stand panel

L2 Q.5 Before commencing maintenance on the Weather radar antenna assy, what precaution
should you observe?

 a] select the “Disable Switches” on the ANT pedestal to ‘OFF’


b] TILT the ANT 150 up
c] select the ‘Left’ and ‘Right’ Weather Radar system and ensure power is available

L2 Q.6 The Weather Radar is switched ‘ON’ by selecting:

 a] either of the Weather radar pushbutton to ‘ON’ at the EFIS control panels
b] the ‘Test’ position only
c] only by the left or right RT pushbutton on the pedestal

L2 Q.7 The Weather display on the ND is indicated when the ND mode switch is:

 a] not in the plan mode


b] in the centre approach mode
c] in the expanded plan mode
L2 Q.8 During takeoff, the Predictive windshear turns off automatically:

a] above 800ft
b] below 2300ft
 c] above 2300ft

L2 Q.9 A predictive windshear symbol is displayed on the ND if PWS is detected and the
aircraft is:

a] above 1200ft radio altitude


 b] below 1200ft radio altitude
c] below 2300ft radio altitude

L2 Q.10 The Weather radar antenna SCAN and ELEVATION disable switches when selected to
OFF will stop:

 a] the antenna movement only


b] the antenna movement and RF transmission
c] the RF transmission for maintenance purposes

L2 Q.11 What range does the Weather radar turbulence mode have?

 a] 40NM
b] 80NM
c] it’s variable depending on the selection

L3 Q.12 The purpose of the LANDING GEAR lever module signal to the PWS is:

a] to inhibit the weather radar test in flight


 b] to use in the take off and approach alert logic
c] to arm the Predictive Windshear only when the gear is ‘up’
ATA 23 – FLIGHT INTERPHONE/SERVICE INTERPHONE/GROUND CREW CALL

L1 Q.1 The flight crew uses the flight interphone system to speak:

a] with each other


b] to the ground crew
 c] with each other and to the ground crew

L1 Q.2 Which unit controls the routing of audio signals to and from the flight crew for the flight
interphone system?

a] passenger address/cabin interphone controller


b] VHF transceivers
 c] audio management unit

L1 Q.3 The ground crew uses the service interphone system to talk:

a] to each other
b] to the flight crew
 c] to each other and to the flight crew

L1 Q.4 The service interphone switch is:

a] in the main equipment center


 b] in the flight deck
c] in the cabin

L1 Q.5 The audio management unit is:

a] in the cabin
b] on the flight deck
 c] in the main equipment center

L1 Q.6 The ground crew call horn and the service and APU shutdown panel are in the:

a] cockpit
 b] nose wheel well area.
c] main equipment center

L1 Q.7 The ground crew pushes the flight deck call switch on the service and APU shutdown
panel to call the:

 a] flight deck
b] cabin attendants
c] other ground crew and cabin attendants
L1 Q.8 To initiate a ground crew call from the flight deck, selection is made from the:

a] Radio Tuning Panel


 b] Control Display Unit
c] Audio Control Panel

L2 Q.9 What is the function of the observer audio selector switch on the centre pedestal?

a] it allows the first officer to use the captain’s station card in the audio management
unit
 b] it allows the captain or first officer to use the first observer’s station card in the
Audio Management Unit
c] it allows the first observer to use the captain’s or first officer’s station card in the
Audio Management Unit

L2 Q.10 The cockpit / flight deck handset can be used:

a] for flight interphone


b] only for PA
 c] for cabin interphone and PA

L2 Q.11 The left and right flight interphone speaker volume is controlled from:

a] the captain’s Audio Control Panel only


b] either the captain’s, first officer’s or the observer Audio Control Panels
 c] The captain’s Audio Control Panel for the left speaker and the first officer’s Audio
Control Panel for the right speaker

L2 Q.12 The receiver LED on the Audio Control Panel illuminates:

a] when the transmit select switch pressed


 b] when the receiver volume control is selected
c] only when the radio signal is received

L2 Q.13 The purpose of the service interphone switch on the overhead panel P5 is to connect
the:

 a] flight interphone system with the service interphone system


b] flight interphone system with the cabin interphone system
c] service interphone system with the cabin interphone system
L2 Q.14 The Service Interphone system is powered:

 a] when the ground handling bus is powered


b] by the hot battery bus
c] only when INT is selected on the Audio Control Panel

L2 Q.15 The service interphone jacks are in:

a] one group
b] two groups
 c] three groups

L2 Q.16 The service interphone headset is:

a] a hand mike and speaker


 b] a boom microphone and headphone
c] a portable telephone handset

L2 Q.17 The flight crew and the ground crew use the ground crew call system to tell each other
to answer a call on the:

 a] flight interphone system


b] cabin interphone system
c] passenger interphone system

L2 Q.18 The Ground Crew Call system supplies aural and visual signals:

a] in the flight deck


b] in the nose wheel well area
 c] in the flight deck and in the nose wheel well area
ATA 23 – VHF/HF

L1 Q.1 Which VHF Radio can provide data communications from the flight deck?

a] left
b] left and right
 c] centre or right

L1 Q.2 The Left VHF antenna is located in the:

 a] top fuselage area


b] lower fuselage area
c] vertical fin area

L1 Q.3 Which component do you use to select the frequency for VHF communication?

a] Audio Control Panel


 b] Radio Tuning Panel
c] Control Display Unit

L1 Q.4 The HF antenna couplers are located in the:

a] ceiling compartment
b] nose radome
c] vertical stabilizer

L2 Q.5 Which VHF system will be powered with only Battery power available?

 a] Left VHF system


b] Left and Centre VHF systems
c] All 3 VHF systems

L2 Q.6 The VHF communication system permits voice and data communication over:

a] sky wave distances


 b] line-of-sight distances
c] long range

L2 Q.7 The VHF communication system permits communication:

 a] between airplanes or between ground stations and airplanes


b] between ground stations and airplanes
c] between airplanes
L2 Q.8 The Audio Control Panels are part of the:

a] cabin interphone system


 b] flight interphone system
c] service interphone system

L2 Q.9 If a HF antenna coupler ‘FAULT’ is reported, which of these could be the most probable
cause?

 a] the ANT coupler has an internal pressure loss


b] the HF transceiver power is weak
c] the ANT coupler has moved to a home position

L2 Q.10 On the HF transceiver, the LRU FAIL indicator light comes on for:

a] an antenna coupler fault


 b] a transceiver fault
c] a RTP tuning fault

L2 Q.11 For long range communication, the HF system uses:

a] ground waves
 b] sky waves
c] microwaves

L2 Q.12 On the HF system, pressurization is through the pressure valve on the front of the:

 a] coupler
b] antenna
c] transceiver

L3 Q.13 Tuning of HF system completes when:

a] the respective frequency is selected on the Radio Tuning Panel


b] a self test is carried out
 c] the tuning tone is interrupted
ATA 23 – SELCAL/ELT

L1 Q.1 The SELCAL system:

a] tells the ground crew that there is a call from the aircraft on a communication
transceiver
b] tells the flight crew that there is a call from a ground station on a navigation
receiver
 c] tells the flight crew that there is a call from a ground station on a communication
transceiver

L1 Q.2 The SELCAL system:

a] has aural indication only


 b] has aural and visual indications
c] has visual indications only

L1 Q.3 Which system automatically sends emergency signals when it senses a large change in the
airplane velocity?

a] cockpit voice recorder


b] flight data recorder system
 c] emergency locator transmitter system

L1 Q.4 The emergency locator transmitter control panel is in the flight deck on the:

 a] overhead panel.
b] aisle stand panel
c] captain side panel

L2 Q.5 The Flight Crew identifies a SELCAL message in the cockpit by:

a] a CALL message on the left or right Control Display Unit


 b] an EICAS message, a chime, and a CALL light on the Audio Control Panels
c] the flight interphone receiver light illuminating

L2 Q.6 SELCAL is normally received by:

a] the 3 VHF systems only


b] both HF systems only
 c] VHF and HF systems

L2 Q.7 The ‘Call’ light on any VHF pushbutton on the ACP illuminates for:

 a] SELCAL
b] data link
c] cabin interphone call
L2 Q.8 The SELCAL decoder is:

 a] in the main equipment center


b] in the aft cargo compartment
c] beside the cockpit door

L2 Q.9 A SELCAL coding switch:

a] connects to the SELCAL control panel and displays the SELCAL code on the
instrument panel
 b] connects to the SELCAL decoder and gives each airplane its SELCAL code
c] monitors for audio tones
ATA 23 – CABIN INTERPHONE

L2 Q.1 The primary component of the Cabin Interphone System is the:

a] flight deck handset


 b] passenger address/cabin interphone controller
c] cabin system control panel

L2 Q.2 If the normal Cabin Interphone Controller fails, alternate selection is made from the:

a] passenger address/cabin interphone controller


 b] attendant switch panel (Door 1L)
c] cabin system control panel

L2 Q.3 If there is a problem with the cabin interphone system, how can you quickly determine if
the problem is in the passenger address/cabin interphone controller or not:

a] make a cabin interphone call


 b] select the Cabin Interphone NORM/ALT switch on the attendant switch panel to
ALT
c] carry out an ALL test

L2 Q.4 To make a call to the cabin attendants from the cockpit using the boom mic:

a] push the FLT transmit switch on the ACP. Then use the centre CDU to select a
dial code
 b] push the CAB transmit switch on the ACP. Then use the centre CDU to select a
dial code
c] transfer the SERV INT toggle switch on P5 to ‘ON’

L2 Q.5 Attendant to attendant call chimes are generated in the:

 a] PA/CI controller
b] AIMS cabinets
c] Warning Electronics Unit
ATA 23 – PAS/SATCOM/DCMF/EFB/FDEVSS/CVR/PC PWR

L1 Q.1 The passenger address system:

a] sends short message services to all passengers


 b] lets the crew send announcements and other audio to the passenger cabin
c] lets the passenger communicate with attendant crew using a handset

L1 Q.2 Which system receives audio inputs and sends them to the passenger cabin?

a] flight interphone system


b] passenger service system
 c] passenger address system

L1 Q.3 Which type of passenger address announcement has the least priority?

a] direct access from cabin


 b] boarding music
c] cabin interphone

L1 Q.4 Satellites act as relay stations:

a] between the airplanes


b] between four ground stations
 c] between the ground stations and the airplane

L1 Q.5 SATCOM can be used:

a] only for voice


b] only for data
 c] for data and voice

L1 Q.6 SATCOM components are generally located in:

a] the Main Equipment Centre


b] the Fwd. cargo area (E5)
 c] the cabin ceiling (E11)

L1 Q.7 The display select panel is on the:

 a] glareshield
b] overhead panel
c] aisle stand panel
L1 Q.8 Which VHF systems provide the data link facility?

a] left and right


 b] right and centre
c] all the 3 systems

L1 Q.9 Which reference lets the flight crew access to the electronic flight operation data,
general purpose computing and communications:

 a] Electronic Flight Bag


b] Control Display Unit
c] Maintenance Access Terminal

L1 Q.10 Each Electronic Flight Bag system consists of:

a] a database loader and an electronics unit


 b] a display unit and an electronics unit
c] a control display unit

L1 Q.11 On the B777-300ER aircraft, the Camera Interface Unit is located in the:

a] cockpit
b] forward electronics compartment
ü c] forward galley area

L1 Q.12 On the B777-300ER aircraft, the video display from the 3 cameras is viewed on the:

a] MFD
ü b] EFB display unit
c] ND

L1 Q.13 Which system continuously records flight deck sounds?

a] flight data recorder


 b] cockpit voice recorder
c] cassette data recorder

L1 Q.14 How many minutes of audio does the cockpit voice recorder system keep?

a] 60
 b] 120
c] 180
L1 Q.15 The PC Power System is a 110 VAC/60Hz power system that supplies power for:

a] personal computers
b] hair dryers or shavers
 c] laptop computers or other passenger electronic devices

L1 Q.16 The PC Power System Master Control Unit is installed in the:

 a] passenger compartment ceiling.


b] video control center
c] main equipment center

L2 Q.17 Which type of passenger address announcement has the highest priority?

 a] flight crew (from the flight interphone system)


b] flight attendant (from direct access)
c] Pre Recorded Announcement

L2 Q.18 In each zone how many columns of Speaker Drive modules are there?

a] 2
b] 3
 c] 1

L2 Q.19 Each Speaker Drive module can drive:

a] 3 speakers
 b] 4 speakers
c] 2 speakers

L2 Q.20 Which component in the SATCOM system contains system operation software and
position/ frequency data for each satellite?

 a] Satellite Data Unit


b] Radio Frequency Unit
c] Beam Steering Unit

L2 Q.21 Passengers use the SATCOM system through the:

a] control display units


 b] cabin telecommunications unit
c] audio management unit
L2 Q.22 The ground station connects the SATCOM system to the:

a] public telephone networks


b] ground-based ACARS
 c] ground-based ACARS and public telephone networks

L2 Q.23 The ‘ACARS’ modems are located in:

a] the ACARS management unit in the MEC


 b] both AIMS cabinets
c] the centre VHF transceiver

L2 Q.24 The DCMF does not interface with the:

a] center VHF transceiver


b] right VHF transceiver
 c] left VHF transceiver

L2 Q.25 On the Electronic Flight Bag system, Electronic Units send display data to their on-side
Display Units on:

a] Ethernet 10 base T data Bus


ü b] Fibre optics connection
c] ARINC 629 Data Bus

L2 Q.26 Which components are in the main equipment center that interface with the Electronic
Flight Bag?

a] Portable Display Units


 b] Electronic units
c] Printer

L2 Q.27 On B777-300ER aircraft, the power supply to the 3 Video cameras is:

a] 115V AC
ü b] 12V DC from the camera interface unit
c] 28V DC from EFB electronics unit

L2 Q.28 The Flight Deck Entry Video Surveillance System (FDEVSS) is a video system that
provides the flight crew surveillance capability of the:

 a] flight deck doorway and the forward galley areas


b] passenger doorway and galley areas
c] flight deck doorway and the flight deck lavatory area
L3 Q.29 On the B777-300ER Electronic Flight Bag, the Display Units give each other display
data through:

a] an Ethernet 10 base T bus


ü b] a Fibre optic connection
c] an ARINC 429 bus

L3 Q.30 On the B777-300ER Electronic Flight bag main menu page, if the “Initialize Flight’ button
is selected:

a] power up takes place for 10 minutes


ü b] all faults on the system page will be permanently removed
c] the flight number has to be loaded through the PMAT
ATA 44 – IFE MAS 2000e

L1 Q.1 In the MAS 2000e system, the Cabin Crew controls and monitors system functions from
the:

a] Flight Attendant Panel


 b] Cabin Management Terminal II
c] Seat Display Unit

L1 Q.2 In the MAS 2000e system, overhead video components (Projectors and Monitors) are
located in the:

a] cockpit overhead
b] overhead and galleys
 c] overhead and throughout the cabin

L1 Q.3 In the MAS 2000e system, which handset is used to control and indicate the selection of
video programs, including Airshow, to be viewed on the Seat Display Unit?

a] Flight Deck Handset


 b] Passenger Telephone Handset
c] Cabin Attendant Handset

L1 Q.4 Which MAS 2000e component provides all operational controls for the Audio and Video
(Overhead and In-Seat) networks and for all maintenance functions?

 a] Cabin Management Terminal II


b] Airshow
c] Passenger Telephone Handset

L1 Q.5 In the MAS 2000e system, the number of external video cameras that provide video to
the System 2000e:

 a] two
b] three
c] four

L1 Q. 6 Which services are provided by the MAS 2000e system?

a] audio, video, navigation, interactive, PSS


b] audio, video on demand, interactive, PSS
 c] audio, video, telephone, interactive

L1 Q. 7 In the MAS 2000e system, which LRUs are audio/video sources?

 a] VCPs. CDRs, PRAM, airshow


b] EPESC, CMEU II, EVSCU, CMI, CPMU
c] PRAM, LAN HUB, TU VMU, VDU
L1 Q.8 In the MAS 2000e system, the Video Cassette Players can be controlled from?

a] the CMT and the seat


 b] the CMT and manually at the VCP
c] the EVSCU and the seat

L2 Q. 9 In the MAS 2000e system, which LRUs are connected to the LAN HUB?

a] CMT, handset, ASEB VASEB, IVASEB


b] EADB, TU, VMU, VDU
 c] EPESC, CMEU II, EVSCU, CMT

L2 Q.10 In the MAS 2000e system, Which LRUs are distribution types?

a] LAN HUB, CDR, PRAM, DIU


 b] EADB, VDU
c] LCD, handset, VASEB

L2 Q.11 In the MAS 2000e system, Which LRUs are seat LRU types?

a] EPESC, CMEU II, EVSCU, CMT, CPMU


b] VCPs, CDRs, PRAM, airshow
 c] LCD, handset, IVASEB

L2 Q.12 The number of Zone Interface units on the B777-200 is:

a] 1
b] 4
 c] 3

L2 Q.13 In the MAS 2000e system, Which LRUs are considered to be on the “core” LAN?

 a] EPESC, EVSCU, CMT, CMEU II


b] EVSCU, IVASEB, EPESC, CMEU II
c] CMT, EPESC, CMEU II and ZIU

L2 Q.14 In the MAS 2000e system, which LRU is found in both the ‘core’ and ‘cabin’ LAN?

a] EVSCU
 b] EPESC
c] CMEU II
L2 Q.15 In the MAS 2000e system, the airshow digital interface unit is responsible for:

a] sending out video signals to the EVSCU


b] audio entertainment to the cabin
 c] sending out video signals of flight data to the VMU

L2 Q.16 In the MAS 2000e system, which LRU is in the seat LAN?

 a] IVASEB
b] VMU
c] EVSCU

L2 Q.17 In the MAS 2000e system, what is the ‘primary’ purpose of the CMEU II?

 a] it is a network file server


b] it is a token ring interface
c] it is an interface with the cabin LAN

L2 Q.18 In the MAS 2000e system, which interface card is used to connect the system 2000E
with the aircraft telephone system?

a] token ring card


b] analog audio car
 c] ZTC

L2 Q.19 In the MAS 2000e system, what type of video signal is output from the VCPs?

a] RF video
 b] baseband
c] digital

L2 Q.20 In the MAS 2000e system, which internal sensor will cause the VCP to be disabled?

a] video sensor
b] tape sensor
 c] DEW sensor

L2 Q.21 In the MAS 2000e system, where is the ZTC located?

a] in the VCC
 b] inside the EPESC
c] in the EE-BAY
L2 Q.22 The primary purpose of the ZIU in the MAS 2000e system is to interface with:

a] Airshow
b] the aircraft systems
 c] PSS

L2 Q.23 In the MAS 2000e system, if you have no PSS in First class what could cause this?

a] IVASEB
 b] ZIU
c] EVSCU

L2 Q.24 In the MAS 2000e system, what happens to the token ring on the cabin LAN if EADB 3
loses power?

a] the network fails due to no power


b] the network fails due to open ring
 c] it is bypassed by the token ring relays
ATA 44 – IFE MAS 3000i

L1 Q.1 In the MAS 3000i system, In-seat entertainment equipment is installed in the:

a] cabin attendant seats


 b] passenger seats
c] cockpit seats

L1 Q.2 In the MAS 3000i system, the Cabin Management Terminal is in the:

a] Main Equipment Center


 b] Video Control Center
c] Aft Cargo Compartment

L1 Q.3 In the MAS 3000i system, the Cabin Telecommunication Unit is in the:

a] Video Control Center


b] Center Equipment Center
 c] Aft Cargo Equipment Center

L1 Q.4 In the MAS 3000i system, the Enhanced Area Distribution Box is:

a] under the seats.


 b] overhead in the cabin
c] in the video control center

L1 Q.5 In the MAS 3000i system, audio and video on demand (AVOD) components are located in
the:

a] Main Equipment Center


 b] VCC lower compartment
c] Cabin ceiling

L1 Q.6 In the MAS 3000i system, at each seat, the passenger has the IFES audio, supplied to
the:

a] Passenger Control Unit


b] Seat Display Unit
 c] Remote Jack Unit

L1 Q.7 In the MAS 3000i system, the DVD Player is used for:

a] Audio/Video On Demand
 b] Overhead Video
c] Software loading
L1 Q.8 In the MAS 3000i system, audio to the seats is normally from the:

a] VMU
b] tape reproducers of the avionics compartment
 c] Hard Disk Drive Array

L2 Q.9 In the MAS 3000i system, the token ring interface with the CMT is via DSEB 1 and the:

a] Token Ring Interface Box


 b] EADB 4
c] EADB 1

L2 Q.10 In the MAS 3000i system, Audio and Video signals from the Hard Disk Drive Array to
the QAM Modulator Unit are transmitted using:

a] RS-485 data transfer


 b] Fibre Channel HUB
c] Small Computer System I/Face (SCSI) data transfer

L2 Q.11 In the MAS 3000i system, selecting any one of the IFE Zone switches to OFF will
isolate power to its dedicated:

 a] EADBs and DSEBs only


b] EADBs, DSEBs, VDUs and LCDs
c] VDUs and LCDs only

L2 Q.12 In the MAS 3000i system, overhead video is distributed from the Video Modulation Unit
via the RF Combiner-splitter/RF distribution Amplifier to the:

a] EADBs and TUs


b] EADBs and VDUs
 c] VDUs directly

L2 Q.13 In the MAS 3000i system, the Audio/Video on Demand signals are sent to the Digital
Seat Electronic Box in:

a] MPEG format
b] Video RF and ADPCM audio format
 c] RF QAM format

L2 Q.14 In the MAS 3000i system, Audio and Video On Demand signals are sent to the Digital
Seat Electronic Box via the:

 a] RFCS/RFDA and EADBs


b] EPESC, RFCS/RFDA and EADBs
c] VMU, RFCS/RFDA and EADBs
L2 Q.15 In the MAS 3000i system, how many smoke detectors are in the VCC ventilation
system?

a] 2
 b] 3
c] 4

L2 Q.16 In the MAS 3000i system, the VCC supplemental cooling fan re-circulates the air from:

 a] Main Equipment Center


b] Cabin
c] Forward cargo

You might also like