Professional Documents
Culture Documents
KON, TPO, EZD, KOHU, KOKU, IMT - 1VLM000594 Rev.4, en
KON, TPO, EZD, KOHU, KOKU, IMT - 1VLM000594 Rev.4, en
M E D I U M VO LTAG E P R O D U C T S
—
Scope of Contents
3 1. General description
3 2. Service conditions
3 3. Technical details
4 4. Instructions for installation
4 General information
4 Checking current transformer
upon arrival
5 Preparations before
installation of current
transformers
5 Activities after the installing
of the transformer and before
bringing it into operation
5 Safety instructions
6 Mounting
6 Primary connection
7 Primary reconnactable
transformers
8 Secondary connections
9 5. Maintenance and overviews
during exploitation
9 Maintenance
9 Overviews during exploitation
9 6. Instructions for use
11 7. Package, transport and
storage
10 8. Handling with the
transformers
10 9. Disposal
10 10. Normative references
11 11. Wiring diagram examples
13 12. Dimensions drawings
3
—
Instructions for installation, use and
maintenance for current transformers
This installation, use and maintenance These instructions are valid for
Current transformer type:
guide is valid for current transformers KON, TPO, EZD, KOHU, KOKU, IMT
operating in outdoor conditions.
—
01 Example of outdoor
1. General description 2. Service conditions
CT’s rating plate 74x62
mm (TPO 73.11)
The current transformers are designed to supply The transformers should be mounted in outdoor
— measurement and protection circuits in high conditions where the ambient air may be polluted
02 Example of outdoor
rating plate (KON 17 I2C)
voltage power networks (with admissible voltage by dust, smoke, corrosive cases, vapors or salt.
up to 40.5 kV and frequency 50 Hz or 60 Hz). The current transformers are designed for
This installation, use and maintenance guide is standard ambient temperature between -40°C
valid for current transformers operating in and +40°C and altitude lower than 1000 m above
outdoor conditions type: the sea level. The average value of the ambient
KON, TPO, EZD, KOHU, KOKU, IMT. temperature, measured over a period of 24 hours,
Design versions may differ depending on: should not exceed 35°C.
• type CT (support, bushing, cable) The transformers may be used also in higher or
• rated insulation level, lower ambient temperatures and higher altitudes
• rated primary current, when agreed between the manufacturer and
• rated secondary current, purchaser.
• Štítky
ratedkpower
zakázce: 736777
in given / Labelsclass,
accuracy for order: 736777
• thermal/dynamic current.
ÚV E43973707 - 6 ks
3. Technical details
1VLT5119053458
s.n. 1VLT5119053458
1VLT5119053459
The technical details for each individual
TPO 70.11 1VLT5119053460
or.n.:736777 transformer are mentioned on the rating plate
500//1/1A 50 Hz 1VLT5119053461
fastened on the transformer. Parameter values
1S1-1S2 500/1A cl.5P20 25VA 1VLT5119053462
indicated on the rating plate must not be
2S1-2S2 cl.PX cl. PX 2/1000
Ukp≥500.0V, Io≤0.1A, Rct≤5.0Ω
1VLT5119053463
exceeded.
Icth:600A 90.0kg
36/70/170 kV Ith: 25(3s) kA 40°C
IEC 61869-2 Idyn: 62.5 kA E
TCM 212/99-3084 Made by ABB 2019
—
01
—
02
4 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
Attention: All electrical tests listed in these Attention: Maintenance of the transformers
instructions should be done in accommodations should be done in accordance with
meeting the requirements given in the the safety and occupational hygiene
catalogue card in consideration of the requirements for electrical equipment.
ambient temperature and the humidity.
6 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
High ratio
Low ratio Ipn = 2 x Ip
Ipn = Ip P1 connected to C1
C1 connected to C2 and P2 connected to C2
TPO
KON
8 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
— Secondary connections
03 Example of cur-
rent transformers Terminals, terminal screws, nuts and washers are
terminal boxes made of brass or stainless steel. The secondary
— terminals are provided with M6 or M5 screws for
04 Label inside of the wiring connection. The terminal box is provided
secondary terminal
box indicating each with one or two PG21 or PG16 (KOKU) cable gland.
secondary terminal. The cover of the terminal box is provided with
Available for TPO 6.
lead seal lock. In outdoor transformers degree
of IP54 protection for terminal boxes.
—
04
9
Maintenance
Excessive dust or other kind of pollution must be
brushed off the transformer. Polluted
transformers can be cleaned with spirit, petrol or 6. Instruction for use
toluene. Traces of arcs and minor surface
damages can be easily removed with sandpaper Current instrument transformers are used:
after which the surface is to be treated by • to convert large currents in the primary circuit
applying a thin layer of silicone paste on it. to an appropriate level for secondary circuit
Instruction for repairing greater surface damages equipment (relays and meters)
must be requested from the manufacturer. • to insulate primary and secondary circuit from
each other to protect the secondary equipment
Overviews during exploitation from the harmful effects of large current
Medium voltage instrument transformers in resin appearing during the operation (short circuits)
insulation are maintenance-free. However,
because of work under different environmental The use of current transformer for other purpose
conditions during the transformer operation it is then described above is forbidden if not agreed
advisable to carry out: with the producer.
• overview of the instrument transformer during
operation – only visual control, For special request can be delivered additional
• overview of the instrument transformer documents as:
disconnected from power supply. • routine test report
• additional rating plate,
Time periods between inspections is regulated by • theoretical current errors and phase
standards, by operation and maintenance manual displacement values,
of switchgears or user requirements. • theoretical excitation curves,
Overview of the instrument transformer during • accuracy test report,
operation. • magnetizing curve,
The review is based on visual control in • verification tests.
accordance with the principles of safety. During
the inspection should pay attention to:
• condition of resin body,
• condition of primary terminals,
7. Package, transport and
• condition of support structures. storage
The permissible transport and storage
Attention: Overviews during operations
temperature is from –40°C up to +70°C. During
do not apply to the transformers
transport and storage the transformers must be
installed in the cubicles.
protected against direct sunlight. Transformers
assigned for export are packed in wooden crates.
Overview of the instrument transformer discon-
Current transformer should be shipped in
nected from power supply
position according to symbols and marks
The overview should be done every time before
indicated on its packing case and protected
restarting. The overview should include:
against weather conditions. They should be
• cleaning the surface of instrument transformer,
stored in dry and clean places, protected from
• checking condition of the transformer resin
direct exposure to precipitation and solar
body surface,
radiation.
• checking condition of mounting screws and
checking the condition of all electrical
connections (on primary and secondary
terminals and earthing terminals),
• measurement of main insulation resistance,
• measurement of secondary winding insulation
resistance.
10 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
05 Handling by the 8. Handling with Handling by the chain and crane.
chain and crane
Current transformers havier than 40 kg should be
the transformers handled by crain with chains and hooks attached
to the lifting eyebolts (see picture below). Screw
Manual handling.
the lifting eyebolts through the baseplate/rail
Transformers are possible to handle by hands in
and nuts under baseplate/rail properly. Then
case if the weight of the transformer is not higher
attach to the crane’s hook using chains.
than 25kg. For grasp of the transformers always
use handling grip, or the base of the transformer.
Current transformers type KOHU, KOKU, IMT can
be handled by casting. Do not handle the Attention: Lifting capacity of the chains,
transformer using the cable (if the transformer loops and the crane has to be 200kg
has it). Always use the gloves in case of manual at least. Always make sure that the
handling. loops and chains hold safely on.
—
05
—
a) Current transformer
with one secondary
winding
—
b) Current transformer
with two secondary
windings
—
c) Current transformer
with three secondary
windings
—
d) Current transformer
with four secondary
windings
12 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
a) Current transformer
with one secondary
winding reconnectable
by primary side
—
b) Current transformer
with two secondary
windings reconnectable
by primary side
—
c) Current transformer
with three secondary
windings reconnectable
by primary side
—
a) Current transformer
with one reconnectable
secondary winding
—
b) Current transformer
with two reconnectable
secondary windings
—
Weight approx. 30 kg
KON-17I2C Creepage distance: 600 mm
308
247
266
80
18
120 10
40
2x 14
60
°
378
293
IP54
M8 Rating
36
33 plate
5
250 Pg21 M6
177
12 300
362
4xM12X30
40 4x 14x16.5
270
320
14 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
— Weight approx. 30 kg
KON-17I2C Creepage distance: 600 mm
reconnectable
308
247
266
80
10
18
120
40
2x 14
10
60
°
378
293
IP54
M8 Rating
36
33 plate
5
250 Pg21 M6
177
12 300
362 Low ratio
Ipn=Ip
C1 connected to C2
60 6xM12x30
40
4x 14x16.5
High ratio
Ipn=2xIp
P1connected to C1 and
270
320
P2 connected to C2
O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T 15
— Weight approx. 24 kg
KON-24 Creepage dist ance: 800 mm
267
205 102
2x 14
A
2x 14x19
25
B
30
438
351
Pg21
IP54
Rating plate
M8
35
5
17 114 M6
308
4x 11x11
254
276
219
241
— Weight approx. 43 kg
KON-24I2C Creepage distance: 800 mm
362
300 266
18
10
40
2x 14 120
60
°
425
IP54 338
M8
33 Rating
36
plate
5
Pg21 M6
250
177
16 300
366
4xM12x30
40
4x 14x16.5
270
320
17
— Weight approx. 43 kg
KON-24I2C Creepage distance: 800 mm
reconnectable
300 362
80 266
10
18
120
40
2x 14
10
60
°
425
IP54 338
M8 Rating
36
33 plate
5
250 Pg21 M6
177
16 300 Low ratio
Ipn=Ip
366 C1 connected to C2
60
6xM12x30
40
4x 14x16.5
High ratio
Ipn=2xIp
P1 connected to C1 and
270
320
P2 connected to C2
18 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
— Weight approx. 62 kg
TPO 60.11 Creepage distance: 1 100 mm
TPO 60.11 WEIGHT: 62kg
CREEPAGE DISTANCE: 1100mm
440
(239)
100
S
°
10
60
459
382
4xM12
DEEP 25
S
60
18
2x 14
420
380
350
130
32
32
(77)
14 P
4x
195 M6 PG21
100
50
M12
58
30
M10 290
Drawing n.
44615820
19
— Weight approx. 62 kg
TPO 60.12 Creepage distance: 1 100 mm
TPO 60.12 WEIGHT: 62kg
CREEPAGE DISTANCE: 1100mm
440
(239)
100
S
°
60
10
459
382
4xM12
DEEP 25
S
60
18
2x 14
420
380
350
130
32
32
(77)
14 P
4x
50
M12
58
30
M10
290
Drawing n.
44615830
20 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
TPO– 63.11
61.11
Weight approx. 62 kg
TPO 61.11 WEIGHT:1 62kg
Creepage distance: 100 mm
TPO 63.11 CREEPAGE DISTANCE: 1100mm
440
(351)
200
S
10
°
60
445
357
4xM12 S
DEEP 25
80
40
20
4x 14
40
(88)
420
380
350
130
40
4x
14 P
195 PG21
M6
50 100
M12
30
58
M10 290
Drawing n.
44615840
21
—
TPO
TPO 64.11
64.11 – 66.11
Weight approx. 62kg
WEIGHT: 62kg
Creepage distance: 1 100 mm
TPO 65.11 CREEPAGE DISTANCE: 1100mm
TPO 66.11
440
405
184
32 120 S
16
°
60
472
357
4xM12 S
DEEP 25
100
45
18
4x 14
40
350
420
380
130
40
115
14 P
4x
M6 PG21
195
100
50
M12
30
58
M10 290
Drawing n.
44615850
22 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
— Weight approx. 90 kg
TPO 70.11 Creepage distance: 1 600 mm
TPO 70.11 WEIGHT: 90kg
CREEPAGE DISTANCE: 1600mm
440
(239)
100
S
10
°
60
611
534
180
30
50
4xM12 S
DEEP 25
60
18
2x 14
32
(77)
350
300
130
32
4x 14 M6 PG21 100
58
M10 M12
340
Drawing n.
44615790
23
— Weight approx. 90 kg
TPO
TPO 70.12 70.12 Creepage distance:
WEIGHT:1 600
90kgmm
CREEPAGE DISTANCE: 1600mm
440
(239)
100
S
10
°
60
611
534
180
30
50
4xM12 S
DEEP 25
60
18
2x 14
32
(77)
350
300
130
32
4x 14
M6 PG 21
100
58
M10 M12
340
Drawing n.
44615800
24 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
TPO 74.11
TPO 71.11 – 76.11
Weight approx. 90 kg
TPO 76.11
440
405
184
32 120
S
16
°
60
627
512
180
30
50
S
100
4xM12
45
20
DEEP 25
4x 14
45
350
300
130
40
PG21
4x 14 M6
100
58
M10 M12
Drawing n. 340
44615810
25
— Weight approx. 7 kg
KOHU 24 A1 (A2)
26 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
KOKU 072 G3 (G4)
Note:
1. Transformer label
2. Cable length 1,6m
3. Screw M12 x 60
4. 5. Screw M5
27
—
KOKU 072 G5
Note:
1. Cable 2 x 2,5mm2 or 2x4mm2.
28 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
KOKU 1 _C_
29
—
KOKU 1 _F_
30 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
KOKU 1 _H_
31
—
KOKU 1 _J_
32 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
KOKU 1 _K_
33
—
KOKU 1 _L_
34 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
KOKU 1 _M_
35
—
KOKU 1 _P_
36 O U T D O O R C U R R E N T T R A N S F O R M E R S T Y P E : KO N , T P O, E Z D, KO H U , KO K U , I M T
I N S T R U C T I O N S F O R I N S TA L L AT I O N , U S E A N D M A I N T E N A N C E
—
IMT
C ØB
5°
Ø
A
D
ca.54
M6
Note: Ratio A B C D E
1. Cast resin 75/5
2. Cable 2x2,5 mm2 with length 4m labeled 150/5 53 106 55 85 70
250/5
No. ”1” i ”2”;
500/5 73 136 45 100 85
1000/5 95 160 45 112 97
37
—
EZD
— —
C O N TA C T U S NOTE We reserve all rights in this document and in
1VLM000594 Rev.4, en 2022.07.12
ABB s.r.o. We reserve the right to make technical the subject matter and illustrations con-
ELDS Brno changes or modify the contents of this docu- tained therein. Any reproduction, disclosure
Videnska 117, 619 00 Brno, ment without prior notice. With regard to to third parties or utilization of its contents -
Czech Republic purchase orders, the agreed particulars shall in whole or in parts - is forbidden without
Tel.: +420 547 152 021 prevail. ABB does not accept any responsibil- prior written consent of ABB.
+420 547 152 854 ity whatsoever for potential errors or possi-
Fax: +420 547 152 626 ble lack of information in this document. Copyright© 2022 ABB
E-mail: kontakt@cz.abb.com All rights reserved
www.abb.com