Professional Documents
Culture Documents
Willem Pro 2 Only Intelligent Programming
Willem Pro 2 Only Intelligent Programming
Willem PRO 2
PROGRAMMING
CHIP SERVICING
BIOS TUNING
VERSION ZIF
HOUSEHOLDS SERVICING
-To supply the programmer, a power supply feeder cable with 12V direct
current voltage is recommended.
--This device is able to read (feed into a PC), delete (erase from the system)
or record (re-programme anew) individual memory according
to user's requirements.
2 Contents of the package
Accessories:
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
VPP VCC
2 Contents of the package
Connecting programmer to PC
1.Remove programmer from the box and position it so the LPT
connector is on the left side.
2.Connect LPT cable to PC and then to programmer (Fig. 1.1)
Red LED light indicating power supply is on (marked by yellow arrow).
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
VPP VCC
Fig 1.1
Once the power supply has been connected, the power supply signalling LED light
is stronger, and additionally yellow LED (VCC) and green LED (VPP) are on.
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
Installation of software
Programmer test
2.) If the port has been found correctly, the yellow and green LED
lights on the programmer will switch off.
3.) To ensure that the programmer has been connected properly, choose
from "Help" bookmark "Test Hardware" option
Programmer test
Programming
1.) To start programming individual system, you have to choose it from the list
3.) To programme FLASH memory with a file, choose "File => Load" from
upper menu or the open folder icon from the bar, and then find and indicate the file.
lub
4.) If all operations have been run correctly, the programme status bar will
display message "Binary File Loaded OK".
5.) From upper menu choose bookmark "Action => Program/Rest RAM".
6.) Once the above procedure has been completed, the window
will open showing the progress in programming.
The yellow and green LED light and FWH/LPC adapter LED light on
the programmer will switch on.
Programming
Erasing
1.) To erase individual system, choose items "Action => Erase 28/29/49/89/90/PIC"
from the menu..
2.) The widow will open showing a percentage progress in erasing of the system
and the yellow and green LED lights and FWH/LPC adapter LED light will switch on.
3.The system has been deleted correctly if the programme status bar displays
the message "Erase completed".
Microwire EEPROM: <------ Data 8bit -----> (pin 6 ->ORG. [Schematic connect to GND])
93C06, 93C46, 93LC46, 93C56, 93C57, 93C66, 93C76, 93C86 (8bit), AT59C11,
AT59C22, AT59C13 CAT35C102, CAT35C104, CAT35C108 (pullup pin7)
Nonvaltile SRAM:
(Ds12xx) DS1220,DS1225Y, DS1230Y/AB, DS1245Y/AB, DS1249Y/AB
Firmware Hub / LPC FLASH Adapter Firmware Hub/LPC (PLCC32) (PP mode) (3.3V)
-- Firmware Hub 82802AB, 82802AC, AT49LW040, AT49LW080 SST49LF002A,
SST49LF003A, SST49LF004A, SST49LF008A W49V002FA,
W39V040FA -- LPC flash SST49LF020, SST49LF040 W49V002A, W39V040A
Systems for programming(C)
MicroChip PIC
Atmel AVR 8-bit RISC AT90Sxxx (Parallel programming) Adapter 32pin to MCS-51
(read,write,erase,verify,checkempty,Lockbits ,Fusebits) [Flash memory/EEPROM]
AT90S1200,AT90S2313 90S2333, 90S4433, 90S4414, 90S8515, 90S4434,
90S8535 reference AT90S2313 pin Function Lockbit
DIP28-PLCC32
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
VPP VCC
DIP32PLCC32
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
VPP VCC
13
DIP44-DIP40
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
EPROM16BIT DIP42
HUB ON
JP7
JP6
JP8
POWER
VPP
14
EPROM16BIT-DIP40
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
VPP VCC
SOL8
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
VPP VCC
15
MCS51V2
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
TSOP48
HUB ON
JP7
JP6
JP8
POWER
VPP VCC
16
SOP44
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
VPP VCC
PIC16F870-16F877
HUB ON
JH4 VPP JH3 JUMPER
JP7
JP6
JP8
POWER
VPP VCC