Professional Documents
Culture Documents
GE Fanuc - VMIVME-7740 - DS - ST
GE Fanuc - VMIVME-7740 - DS - ST
GE Fanuc - VMIVME-7740 - DS - ST
Video Resolutions Supported occur. A user jumper allows the timeout to cause a reset.
Independent of the jumper, software can enable the watchdog
Screen Colors Refresh Rate timeout to cause a nonmaskable interrupt (NMI) or a
Resolution (bpp)* (Hz)
VMEbus SYSFAIL.
640 x 480 24 60, 75, 85
800 x 600 24 60, 75, 85 NONVOLATILE SRAM — The VMIVME-7740
1,024 x 768 24 60, 75, 85 provides 32 Kbyte of nonvolatile SRAM. The contents of the
SRAM are preserved when +5 V power is interrupted or
1,280 x 1,024 24 60, 75, 85
removed from the unit.
1,600 x 1,200 16 60
PMC EXPANSION SITE — The VMIVME-7740
* bpp = bits per pixel supports IEEE P1386 common mezzanine card specification
Ethernet CONTROLLER — The VMIVME-7740 with a 5 V PCI mezzanine card expansion site. The PMC site
supports Ethernet LANs with dual Intel 82559 Ethernet provides for standard I/O out the VMEbus front panel and I/O
controllers. 10BaseT and 100BaseTX options are supported connection to the VMEbus P2 connection, as well.
via two RJ45 connectors. Remote LAN booting is supported. Contact VMIC for more information concerning
REMOTE Ethernet BOOTING — The third-party PMC modules and compatibility.
VMIVME-7740 utilizes Lanworks Technologies, Inc.’s UNIVERSAL SERIAL BUS (USB) — The
BootWare®. BootWare provides the ability to remotely VMIVME-7740 provides a front panel single connection hub
boot the VMIVME-7740 using NetWare, TCP/IP, or RPL host controller for the USB. Supported USB features include:
network protocols. isochronous data transfers, asynchronous messaging,
BootWare Features: self-identification and configuration of peripherals, and
dynamic (hot) attachment.
• NetWare, TCP/IP, RPL network protocol support
• Unparalleled boot sector virus protection VMEbus INTERFACE — The VMIVME-7740
VMEbus interface is based on the Universe IIB
• Detailed boot configuration screens
high-performance PCI-to-VME interface from
• Comprehensive diagnostics Newbridge/Tundra.
• Optional disabling of local boots
• Dual-boot option lets users select network or local booting SYSTEM CONTROLLER — The on-board VMEbus
system controller capabilities allow the board to operate as a
SERIAL PORTS — Two 16550-compatible serial ports slot 1 controller, or it may be disabled when another board is
are featured on the VMIVME-7740 front panel. The serial acting as the system controller. The system controller may be
channel has a 16-byte FIFO to support baud rates up to programmed to provide the following modes of arbitration:
56 Kbyte/s. Requires two micro-DB9 to standard DB-9
adapters, VMIC P/N 360-010050-001. Round Robin (RRS)
Single Level (SGL)
KEYBOARD AND MOUSE PORTS — The Priority (PRI)
VMIVME-7740 has a combined PS/2 keyboard and mouse
connector. A Y-adapter cable is included. The system controller provides a SYSCLK driver,
FLASH MEMORY — The VMIVME-7740 provides up IACK* daisy-chain driver, and a VMEbus access timeout
to 192 Mbyte of IDE CompactFlash memory accessible timer. The system controller also provides an arbitration
timeout if BBSY* is not seen within a specified period after a
through the secondary IDE port. The VMIVME-7740 BIOS
BGOUT* signal is issued. This period is programmable for
includes an option to allow the board to boot from the Flash
16 or 256 µs.
memory.
16-bit TIMERS — The VMIVME-7740 provides the VMEbus REQUESTER — The microprocessor can
user with three 16-bit timers (in addition to system timers) request and gain control of the bus using any of the VMEbus
request lines (BR3* to BR0*) under software control. The
which are 82C54 compatible. These timers are mapped in I/O
requester can be programmed to operate in any of the
space, and are completely software programmable.
following modes:
WATCHDOG TIMER — The VMIVME-7740
provides a software-programmable watchdog timer. The Release-On-Request (ROR)
watchdog timer is enabled under software control. Once the Release-When-Done (RWD)
watchdog timer is enabled, on-board software must access VMEbus Capture and Hold (BCAP)
the timer within the specified timer period, or a timeout will
-12 VDC (±5 percent), 2.5 mA (typical) VMEbus: The VMIVME-7740 enables access to VMIC’s
wealth of VMEbus products. If you have real-world
Note: The currents at +12 and -12 VDC are specified control, monitoring and real-time networking
with the serial connectors open. requirements, VMIC has a solution for you. Today’s
system requirements demand state-of-the-art solutions.
Host Bus
North Bridge
4 Mbyte SDRAM
AGP bus 82443 GX Memory bus
SVGA DRAM Controller SODIMM
Controller
P
SVGA V
C 5.0 V
LAN 2 I PCI-to-VME
M
LAN 1
Bridge
E
Ethernet Ethernet
Controller b b
10BaseT 10BaseT2
Controller Universe IIB
u
100BaseTX Intel 82559 Intel 82559
u 5.0 V
100BaseTX
s s
PCI bus
5.0 V
PMC I/O P2
Comm Port 1 Expansion
Comm Port 2
SUPER-
I/O Compact-
with Flash Drive
South Bridge
RTC PCI-to-ISA, IDE
Accelerator IDE
(PIIX4E)
Floppy Drive
PCI-to-EIDE P2
SMC
FDC37C67X
USB
P2 I
PS/2
Keyboard S
and Mouse
A
b
32 Kbyte NVRAM
u
s
16-bit
Watchdog Timer
NVRAM Controller DS1384
Timers X bus Buffer
82C54
System
BIOS
ROM