Professional Documents
Culture Documents
800-sg005 - En-P (ROCKWELL-ACCESSORIES)
800-sg005 - En-P (ROCKWELL-ACCESSORIES)
PUSH BUTTONS
BULLETIN 800A, 800C, 800M
Bul. 800MR
Bul. 800A
Bul. 800C
TABLE OF CONTENTS
Description Page Description Page
Specifications................................................................................... 4 Potentiometer................................................................................... 19
Push Buttons Pilot Light Units
Momentary Contact, Non-Illuminated ................................. 5 Standard.......................................................................................... 21
Momentary Contact, Illuminated ........................................... 5 Push-to-Test .................................................................................. 21
Push-Pull, Non-Illuminated Dual Input ...................................................................................... 21
2-Position Push-Pull and Push-Pull/Twist Release ........ 7 Wobble Stick Units ........................................................................ 21
3-Position Push-Pull ................................................................... 7 Modifications and Accessories
Push-Pull, Illuminated Color Caps ..................................................................................... 23
2-Position Push-Pull and Push-Pull/Twist Release ........ 9 Knobs ............................................................................................... 24
3-Position Push-Pull ................................................................... 9 Boots ................................................................................................ 24
Selector Switches, Non-Illuminated Miscellaneous................................................................................ 24
2-Position........................................................................................ 11 Replacement Lamps................................................................... 26
3-Position........................................................................................ 13 Legend Plates .................................................................................. 26
4-Position........................................................................................ 15 Approximate Dimensions ........................................................... 28
Selector Switches, Illuminated
2-Position Knob/Lever Type .................................................... 17
3-Position Knob/Lever Type .................................................... 17
4-Position Knob/Lever Type .................................................... 19
Specifications9
Electrical Ratings
Contact Ratings Refer to the Contact Ratings tables below.
1600V for one minute
Dielectric Strength
1300V for one minute (Logic Reed)
750 000 at maximum rated load
Electrical Design Life Cycles
200 000 at maximum rated load (Logic Reed)
Mechanical Ratings
Vibration 10…2000 Hz 1.52 mm displacement (peak-to-peak) Max./10 G Max. (except Logic Reed)
Shock 1/2 cycle sine wave for 11 milliseconds ≥ 25 G (contact fragility) and no damage at 100 G
Degree of Protection Type 13; IEC I44 IP65 Oiltight
Mechanical Design Life Cycles
Push Buttons 1 000 000 minimum
Potentiometers 100 000 minimum
All other devices 200 000 minimum
Contact blocks with Bifurcated spanner:Slow make and break, simple break.
Contact Operation
Logic Reed Contact Blocks:Snap-action
Typical Operating Forces
Operators without contact blocks 2.45 lb (10.8 N)
8 lb (35.3 N) push to in position
Push-Pull Units
4 lb (17.7 N) maximum pull to out position
Standard — 1.5 lb (6.7 N)
Contact Blocks
Logic Reed — 0.616 lb (2.6 N)
Environment
Operating +32…+131 °F (0…+55 °C)
Temperature Range
Storage –40…+185 °F (–40…+85 °C)
Note: Operating temperatures at +32 °F (0 °C) are based on the absence of freezing moisture and liquids.
Humidity –40…+185 °F (–40…+85 °C)
Panel Thickness Requirements 1/16…1/4 in. (1.6…6.4 mm)
9 Performance Data — See page Important-3 in the Industrial Controls catalog.
7 For applications below 24V and 24 mA, Logic Reed contacts are
recommended.
Certifications
UL Listed —File: E14840,
E10314
Guide: NKCR, NOIV
CSA Certified: LR1234, LR11924
IEC Compliance, IEC 529
800MR – A 1 A
a b c d
a b c d
Operator Type Button Color Standard Contact Cartridges Contact Block
Code Description Code Description Code Description Termination Type
A Flush head 1 Green -- No contacts (Blank) Code Description
B Extended head 2 Black A 1 N.O. - 1 N.C. -- Stab terminals (Blank)
G Guarded extended head 3 Orange A2 2 N.O. R Stab terminals, Logic Reed
D Mushroom head 4 Gray A3 1 N.O.E.M. - 1 N.C.L.B.9 K Large screw9
DG Guarded mushroom head 5 White A4 2 N.C. S Small screw9
6 Red A7 1 N.C.L.B. - 1 N.C.9
7 Blue B 2 N.O. - 2 N.C.
9 Yellow D1 1 N.O.
D2 1 N.C.
800MR – PA L 24 R
a b c d e f
a b c e
Operator Illumination Options Input Voltage Standard Contact Cartridges
Transformer Code Description Full Voltage Code Description
Code Description Standard illumination as Code Description -- No contacts (Blank)
PA Flush -- determined by power 06 6V AC/DC A 1 N.O. - 1 N.C.
module type (Blank)
PB Extended 12 12V AC/DC A2 2 N.O.
L LED‡
PF True flush 24 24V AC/DC A3 1 N.O.E.M. - 1 N.C.L.B.9
PGA Guarded flush head 10 120V AC§ A4 2 N.C.
PMB Mushroom Transformer A7 1 N.C.L.B. - 1 N.C.9
Full Voltage Code Description B 2 N.O. - 2 N.C.♣
Code Description 16 120V AC 50/60 Hz D1 1 N.O.
QA Flush 26 240V AC 50/60 Hz D2 1 N.C.
QB Extended
QF True flush
d f
QGA Guarded flush head
Lens Color Contact Block
QMB Mushroom Termination Type
Code Color
A Amber Code Description
B Blue -- Stab terminals (Blank)
C Clear R Stab terminals, Logic Reed
G Green K Large screw9
R Red S Small screw9
W White
X No lens with contact blocks
No lens without
--
contact blocks (Blank)
Push-Pull/
Maintained Maintained Push-Pull Twist Release
Contact Type Out In Button Color Cat. No. Cat. No.
No Contacts — — Red 800MR-FX6 800MR-FXT6
1 N.O. O X Red 800MR-FX6D1 800MR-FXT6D1
1 N.C. X O Red 800MR-FX6D2 800MR-FXT6D2
O X
1 N.O. - 1 N.C. Red 800MR-FX6A 800MR-FXT6A
X O
X O
1 N.C. - 1 N.C. Red 800MR-FX6A4 800MR-FXT6A4
X O
Note: X = Closed/O = Open
3-Position Push-Pull
Cat. No. 800MR-FXN6A7
Operator Position
2-Position Push-Pull and Push-Pull/Twist Release and 3-Position Push-Pull Units, Non-Illuminated
800MR – FX T 6 A
(2-Position) a b c d e f
800MR – FX N 6 A
(3-Position) a b1 c d e f
a c e
Operator Type Button Color Contact Cartridges
Code Description Code Color Code Description
FX Push-Pull Unit -- Non-Illuminated -- No contacts (Blank)
A 1 N.O. - 1 N.C.
b A2 2 N.O.
Operator Function
d
A4 2 N.C.
2-Position Button Color
A7 1 N.C.L.B. - 1 N.C.7
Code Description Code Color
B 2 N.O. - 2 N.C.
-- Maintained — Push-Pull (Blank) 1 Green
D1 1 N.O.
T Twist-Release 2 Black
D2 1 N.C.
3 Orange
b1 Note: See Table 1 for Target description.
4 Gray
Operator Function 5 White
3-Position9 6 Red f
Operator Position 7 Blue Contact Block Termination Type
9 Yellow Code Description
Code -- No cap (Blank) -- Stab terminals (Blank)
R Stab terminals, Logic Reed
Out Center In
K Large Screw7
N Momentary Maintained Momentary
S Small Screw7
Contact
Code Code
Description
Push-Pull/
Maintained Maintained Push-Pull Twist Release
Power Supply
Lamp Type Module Type Voltage Lens Color Contacts Out In Cat. No. Cat. No.
12V AC/DC Red N.O. - O X 800MR-FXQ12RA 800MR-FXTQ12RA
Full Voltage
24V AC/DC Red N.C. X O 800MR-FXQ24RA 800MR-FXTQ24RA
Incandescent
120V AC9 Red N.O. - O X 800MR-FXP16RA 800MR-FXTP16RA
Transformer
240V AC9 Red N.C. X O 800MR-FXP26RA 800MR-FXTP26RA
12V AC/DC Red N.O. - O X 800MR-FXQL12RA 800MR-FXTQL12RA
Full Voltage
24V AC/DC Red N.C. X O 800MR-FXQL24RA 800MR-FXTQL24RA
LED
120V AC9 Red N.O. - O X 800MR-FXPL16RA 800MR-FXTPL16RA
Transformer
240V AC9 Red N.C. X O 800MR-FXPL26RA 800MR-FXTPL26RA
Note: X = Closed/O = Open
2-Position Push-Pull and Push-Pull/Twist Release and 3-Position Push-Pull Units, Illuminated
800MR – FX T P 16 R A
(2-Position) a b c d e f g h
800MR – FX N P 16 R A
(3-Position) a b1 c d e f g h
a d f h
Operator Type Illumination Options Button Color Contact Block Termination Type
Code Description Code Description Code Color Code Description
FX Push-Pull Unit -- Incandescent lamp (Blank) A Amber -- Stab terminals (Blank)
L LED7 B Blue R Stab terminals, Logic Reed
b
C Clear K Large Screw♣
Operator Function e G Green S Small Screw♣
2-Position Voltage R Red
Code Description Full Voltage W White9
-- Maintained (Blank) Code Description X No cap
T Twist-Release 06 6V AC/DC
12 12V AC/DC g
b1
24 24V AC/DC Contact Cartridges
Operator Function
10 120V AC‡ Code Description
3-Position
Transformer -- No contacts (Blank)
Operator Position
Code Description A 1 N.O. - 1 N.C.
16 120V AC 50/60 Hz A2 2 N.O.
Code
26 240V AC 50/60 Hz A4 2 N.C.
Out Ctr. In A7 1.N.C.L.B. - 1 N.C.♣
N Mom Main Mom B 2 N.O. - 2 N.C.§
Mom-Momentary Main-Maintained D1 1 N.O.
D2 1 N.C.
c Note: See Table 2 for Target description.
Operator Type
Code Description
P Transformer
Q Full Voltage
Contact
Code Code
Description
800MR – H A 2 B L A
(Selector Switch) a b c d e e1 f
800MR – H 31 B L A
(Cylinder Lock) a b c1 c2 d e e1 f
a c c2 (cont’d) e1
Operator Positions Operator Function Key Codes7 Contact Cartridges
Code Description Standard Knob Code Key No. Master Key Code Description
H 2-Position Selector Switch Code Description 10 T136 2T -- No contacts (Blank)
H 2-Position Cylinder Lock 2 Maintained 11 T142 2T A 1 N.O. - 1 N.C.
4 Spring Return From Left 12 T145 2T A2 2 N.O.
5 Spring Return From Right 13 T146 2T A4 2 N.C.
14 T147 2T B 2 N.O. - 2 N.C.
b c1
15 T152 2T D1 1 N.O.
Operator Color and Type Operator Function/
Locking Position9 16 T196 2T D2 1 N.C.
Standard Knob
17 T221 2T P1 3 N.O.
Code Description Maintained
Code Description 18 T224 2T P2 3 N.C.
X No Knob
31 Lock in Left 19 T231 2T P3 2 N.O. - 1 N.C.
A Red
32 Lock in Right 20 T234 2T P4 2 N.C. - 1 N.O.
B Green
33 Lock in Both 21 T265 2T P5 4 N.O.
C Blue
Spring Return From Left 22 T267 2T P6 4 N.C.
E Yellow
Code Description 23 T268 2T P7 3 N.O. - 1 N.C.
F Orange
42 Lock in Right 24 B721 Special P8 1 N.O. - 3 N.C.
G Gray
Spring Return From Right 25 T280 Special Note: See Table 1 for Target
H Black
Code Description 26 T920 Special arrangements
J White
Knob Lever 48 Lock in Left
X No Knob Lever
c2 d f
L Red
Key Codes7 Cam Type Contact Block Termination Type
M Green
Code Key No. Master Key Code Description Code Description
N Blue
Standard B B cam -- Stab terminals (Blank)
R Yellow -- 1T
(Blank) R Stab terminals, Logic Reed
S Orange
02 T101 1T K Large screw‡
T Gray e
03 T102 1T S Small screw‡
K Black
04 T106 1T Contact Cartridge Position
V White
05 T107 1T Code Description
Cylinder Lock
06 T108 1T -- Both left and right (Blank)
-- Key (Blank)
07 T109 2T L Left
08 T134 2T
09 T135 2T
A
Left
B O O O X
Maintained
O O X O
Black in All 800MR-NH2QB 800MR-NK2QB
X O O O
2 N.O. - 2 Positions
O X O O
N.C. A
Right
B
A
Left
B
O O O X
Maintained
O O X O
in All 800MR-N61QB 800MR-N31QB 800MR-N32QB
2 N.O. - 2 X O O O
Positions
N.C. O X O O
A
Right
B
800MR – N A 2 Q B
(Selector Switch) a b c d e f
800MR N 31 Q B
(Cylinder Lock) a b c1 c2 d e f
a c1 (cont'd) c2 (cont'd)
Operator Positions Operator Function/Locking Position9 Key Codes‡
Code Description CH501 Key Code Description Master Key
N 4-Position Selector Code Description 14 T147 2T
N 4-Position Cylinder Lock 531 Lock in position 1 15 T152 2T
532 Lock in position 2 16 T196 2T
b
533 Lock in position 3 17 T221 2T
Operator Color and Type
534 Lock in position 4 18 T224 2T
Standard Knob
Knob Description Lever 541 Lock in position 1 - 2 19 T231 2T
Code Code 542 Lock in position 1 - 3 20 T234 2T
X No Knob X 543 Lock in position 1 - 4 21 T265 2T
A Red L 544 Lock in position 2 - 3 22 T267 2T
B Green M 545 Lock in position 2 - 4 23 T268 2T
C Blue N 546 Lock in position 3 - 4 24 B721 Special
E Yellow R 551 Lock in position 1 - 2 - 3 25 T280 Special
F Orange S 552 Lock in position 1 - 2 - 4 26 T920 Special
G Gray T 553 Lock in position 1 - 3 - 4
d
H Black K 554 Lock in position 2 - 3 - 4
Cam Type and Target Table
J White V 561 Lock in all positions
Q
-- Key (Blank) --
Contact Type
c2 Target
(Rear View)
c
Key Codes‡
Operator Function9 Left Right
Code Key No. Master Key
Code Description
-- Standard (Blank) 1T O O O X 1 N.O. —
2 Maintained
02 T101 1T O O X O 1 N.C. —
03 T102 1T O X O O — 1 N.O.
c1 04 T106 1T X O O O — 1 N.C.
05 T107 1T Note: X = Closed/O = Open
Operator Function/Locking Position9
06 T108 1T
Standard Key e
07 T109 2T
Code Description Contact Cartridges
08 T134 2T
31 Lock in position 1 Standard Block/Stab Terminations
09 T135 2T
32 Lock in position 2 Code Description
10 T136 2T
33 Lock in position 3 -- No contacts (Blank)
11 T142 2T
34 Lock in position 4 B 2 N.O. - 2 N.C.
12 T145 2T
41 Lock in position 1 - 2
13 T146 2T
42 Lock in position 1 - 3 f
43 Lock in position 1 - 4 Contact Block Termination Type
44 Lock in position 2 - 3 Code Description
45 Lock in position 2 - 4 -- Stab terminals (Blank)
46 Lock in position 3 - 4 R Stab terminals, Logic Reed
51 Lock in position 1 - 2 - 3 K Large screw§
52 Lock in position 1 - 2 - 4 S Small screw§
53 Lock in position 1 - 3 - 4
54 Lock in position 2 - 3 - 4
61 Lock in all positions
Left Right Left Right Left Right Left Right Left Right Left Right Left Right
Side Side Side Side Side Side Side Side Side Side Side Side Side Side
O O X N.O. N.O. N.O. — N.O. — N.O. N.O. — N.O. N.O. N.O. — —
X O O N.C. N.C. — N.O. N.C. N.O. — N.C. N.O. — — — N.O. N.O.
Potentiometer Unit
Cat. No. 800MR-N37
Potentiometer
Type Cat. No.
Operator Only (without Resistive Element) 800MR-N37
800MR – 24 N A L 2 Q B
(3-Position) a b c d e f g h
a d g
Input Voltage Illumination Options Contact Cartridges
Full Voltage Code Description Standard Block
Code Description -- Incandescent (Blank) Code Description
06 6V AC/DC L LED‡ B 2 N.O. - 2 N.C.
12 12V AC/DC
e h
24 24V AC/DC
Operator Function
10 120V AC9 Contact Block Termination Type
Code Standard knob function
Code Description
b 2 Maintained
-- Stab terminals (Blank)
Operator Positions
f R Stab terminals, Logic Reed
Code Description
Cam Type and Target Table
N 4-Position7
Q
c Target
Contact Type
Operator Color and Type (Rear View)
A Red L O O X O 1 N.C. —
B Green M O X O O — 1 N.O.
D Amber P X O O O — 1 N.C.
800MR – P L 24 R
a b c d e
a c d
Operator Input Voltage Lens Color
Transformer Full Voltage Code Color
Code Description Code Description -- No lens (Blank)
P Pilot light 06 6V AC/DC A Amber
PD Pilot light — Dual input diode 12 12V AC/DC B Blue
PDT Pilot light — Dual input transformer 24 24V AC/DC C Clear
PT Pilot light — Push-to-test 10 120V AC‡ G Green
Full Voltage Transformer R Red
Code Description Code Description W White
Q Pilot light 16 120V AC 50/60 Hz
e
QT Pilot light — Push-to-test 26 240V AC 50/60 Hz
Contact Block Termination Type
b Code Description
-- Stab terminals (Blank)
Illumination Options
K Large screw§♣
Code Description
S Small screw§
-- Incandescent (Blank)
Note: If large screw terminations are desired with
L LED7
a dual input transformer, (Cat. No. 800MR-
PDT…), configurator space e must be left
blank.
800MR – M1 A
a b c
a b c
Operator Type Contact Cartridges Contact Block Termination Type
Code Description Code Description Code Description
M1 Wobble Stick -- No contacts (Blank) -- Stab terminals (Blank)
A 1 N.O. - 1 N.C. R Stab terminals, Logic Reed
B 2 N.O. - 2 N.C. K Large screw§
S Small screw§
9 Use only with power module type P (Transformer). Power module is supplied with large screw terminations as standard.
7 LEDs available in red, green, amber, blue, and white. LED color must match lens color, except clear lens supplied with white LED and white lens supplied with
amber LED.
‡ Only available with LED illumination option.
§ Not available with Logic Reed contact blocks.
♣ Only available with Push-to-test units.
Color Caps
Non-Illuminated Devices
Flush Head Push Buttons Extended Head Push Buttons Mushroom Buttons Push-Pull Units Twist or Pull Release Caps
Flush Head Extended Head Twist or Pull
Push Buttons Push Buttons Mushroom Buttons Push-Pull Units Release Caps
Color Cat. No. Cat. No. Cat. No. Cat. No. Cat. No.
Green 800MR-N41 800MR-N21 800MR-N56G 800MR-N160B 800MR-N30B
Black 800MR-N42 800MR-N22 800MR-N56B 800MR-N160H 800MR-N30H
Orange 800MR-N43 800MR-N23 800MR-N56O 800MR-N160F 800MR-N30F
Gray 800MR-N44 800MR-N24 800MR-N56GR 800MR-N160G —
White 800MR-N45 800MR-N25 800MR-N56W 800MR-N160J —
Red 800MR-N46 800MR-N26 800MR-N56R 800MR-N160A 800MR-N30A
Blue 800MR-N47 800MR-N27 800MR-N56BL 800MR-N160C 800MR-N30C
Yellow 800MR-N49 800MR-N29 800MR-N56Y 800MR-N160E 800MR-N30E
Illuminated Devices
Pilot Light Push-to-Test Pilot Light and Push-Pull Unit Mushroom Button Twist or Pull
Illuminated Push Button Release Caps
Push-to-Test Pilots Illuminated
and Illuminated Illuminated Illuminated Twist or Pull
Pilot Lights Push Buttons Push-Pull Units Mushroom Buttons Release Caps
Color Cat. No. Cat. No. Cat. No. Cat. No. Cat. No.
Red 800MR-N1R 800MR-N2R 800MR-N159R 800MR-N156R 800MR-N20R
Green 800MR-N1G 800MR-N2G 800MR-N159G — 800MR-N20G
Amber 800MR-N1A 800MR-N2A 800MR-N159A 800MR-N156A 800MR-N20A
Blue 800MR-N1B 800MR-N2B 800MR-N159B 800MR-N156B 800MR-N20B
White 800MR-N1W 800MR-N2W 800MR-N159W 800MR-N156W —
Clear 800MR-N1C 800MR-N2C 800MR-N159C 800MR-N156C 800MR-N20C
Selector Knob Selector Knob Lever Selector Knob Selector Knob Lever
Cat. No. 800MR-NG Cat. No. 800MR-NK Cat. No. 800MR-LB Cat. No. 800MR-LM
Selector Switch Knobs, Non-Illuminated Selector Switch Knobs, Illuminated
Standard Knob Knob Lever Standard Knob Knob Lever
Color Cat. No. Cat. No. Color Cat. No. Cat. No.
Gray 800M-NG 800M-NT — —
Red 800M-NA 800M-NL — —
Green 800M-NB 800M-NM Red 800M-LA 800M-LL
Blue 800M-NC 800M-NN Amber 800M-LD 800M-LP
Yellow 800M-NE 800M-NR Clear 800M-LY 800M-LZ
Orange 800M-NF 800M-NS Green 800M-LB 800M-LM
Black 800M-NH 800M-NK — —
White 800M-NJ 800M-NV — —
General Accessories
Boots
Description Cat. No.
Insulation Boot
When properly combined with a Bulletin 800MR unit, this device meets CSA grounding 800M-N18
requirements.
Insulation Boot
Cat. No. 800MR-N18
Description Color Cat. No.
Black 800MR-N8
Red 800MR-N9
Rubber Boot Green 800MR-N10
These accessories are used as dust covers. They can be added to Blue 800MR-N11
flush and extended head push button units (illuminated and non-
illuminated) to protect against foreign materials from reaching the
Yellow 800MR-N12
opening between the button and the mounting ring.
Rubber Boot
Clear 800MR-N14
Cat. No. 800MR-N9
Miscellaneous
Description Cat. No.
Padlocking Cover
Stainless steel mounting bracket with clear plastic cover. Guards
against unauthorized operation. Used with round design push
800MR-N6
buttons and selector switches (not for use with wing lever). Also
available for 2-position push-pull units (button must be in the
Padlocking Cover depressed position when the cover is closed).
Cat. No. 800MR-N6
(Padlock not included)
Lamp Remover
This tool can be used to remove and install wedge based lamps in 800M-N5
Illuminated selector switches.
Lamp Remover
Cat. No. 800M-N5
Connectors
Used with wire sizes AWG 18…22. The connectors come in 800M-NT29
packages of 100 pieces.
Connector
Cat. No. 800M-NT2
Mounting Ring
This device is a retaining ring used to keep an operator in the panel 40167-287-02
when removing the guard ring to service the light bulb.
Mounting Ring
Part No. 40167-287-02
Lens Remover
800MS-N9
This device makes it easier to remove the lens.
Lens Remover
Cat. No. 800MS-N9
9 These must be ordered in multiples of 100.
Legend Plates
Standard Size Blank Legend Plate Large Size Blank Legend Plate
Gray (Cat. No. 800MR-W00) Gray (Cat. No. 800MR-W100)
Red (Cat. No. 800MR-W600) Red (Cat. No. 800MR-W6100)
Push Buttons/Pilot Lights
Marking Cat. No. Marking Cat. No. Marking Cat. No.
CLOSE 800MR-W01 LOWER 800MR-W11 SLOW 800MR-W18
DOWN 800MR-W02 OFF 800MR-W09 START 800MR-W19
EMERG. STOP (Red) 800MR-W624 ON 800MR-W10 STOP (Red) 800MR-W620
FAST 800MR-W03 OPEN 800MR-W13 TEST 800MR-W21
FORWARD 800MR-W23 OUT 800MR-W12 UP 800MR-W22
HIGH 800MR-W04 PUSH-TO-TEST 800MR-W29 1ST SPEED 800MR-W25
IN 800MR-W06 RAISE 800MR-W14 2ND SPEED 800MR-W26
INCH 800MR-W07 RESET 800MR-W15 3RD SPEED 800MR-W27
JOG 800MR-W08 REV 800MR-W16 4TH SPEED 800MR-W28
LOW 800MR-W05 RUN 800MR-W17 — —
Selector Switches
Marking Cat. No. Marking Cat. No. Marking Cat. No.
OPEN-CLOSE 800MR-W57 STOP-START 800MR-W64 HAND-OFF-AUTO 800MR-W78
RAISE-LOWER 800MR-W58 SUM-WINT 800MR-W65 HIGH-LOW 800MR-W53
RUN-JOG 800MR-W59 UP-DOWN 800MR-W66 JOG-REV 800MR-W54
SAFE-RUN 800MR-W60 1-2-3-4 800MR-W80 JOG-RUN 800MR-W55
SLOW-FAST 800MR-W61 AUTO-OFF-HAND 800MR-W79 JOG-STOP-RUN 800MR-W76
SLOW-OFF-START 800MR-W75 FOR-OFF-REV 800MR-W77 LEFT-RIGHT 800MR-W56
START-JOG 800MR-W62 FOR-REV 800MR-W51 OFF-ON 800MR-W50
START-STOP 800MR-W63 HAND-AUTO 800MR-W52 — —
Cat. No. Cat. No. Cat. No. Cat. No. Cat. No.
800MR-W645 800MR-W646 800MR-W647 800MR-W130 800MR-N50
Format Cat. No. Format Cat. No.
For Push-Pull only
Large Size with Adapter Ring (Blank) 800MR-W645 Push Stop 800MR-W130
Pull Start
Adapter Ring9
Round with Adapter Ring (Blank) 800MR-W646 800MR-N50
Used with Bulletin 800T Legend Plates
Pre-printed includes Adapter Ring
(Cat. No. 800MR-N50)
800MR-W647 — —
Push to Stop
Twist or Pull Release
9 To use the Bulletin 800T legend plates with Bulletin 800MR devices, use adapter ring (Cat. No. 800MR-N50).
Contact Blocks
Bulletin 800M contact blocks are available with quick connect type terminals and screw terminals with pressure plates (in two sizes). Each
quick connect type termination will accept two 0.110 x 0.032 in. push-on connectors or one 0.250 x 0.032 in. connector. Each small screw
terminal with pressure plate will accept a maximum of one #14 AWG wire or two #16 AWG wires. The large screw terminals with pressure
plates are similar in size to the Bulletin 800T (full size) contact block terminals.
Round Push Button Round Push Button Round Push Button Round Selector Switch Panel Wobble
Flush, Extended and Illuminated Flush Mushroom and Potentiometer Stick Unit
Illuminated Extended and Standard Knob
Round Selector Switch Round Cylinder Lock Round Push-Pull Twist or Pull
and Potentiometer Selector Switch Release Units
and Wing Lever
Padlocking Cover9
800MR-N6
9 When using a padlocking cover and depending upon the types of adjacent units involved, the minimum vertical or horizontal spacing may have to be increased
for operating clearance.
‡ Large screw terminal contact blocks require a minimum vertical spacing of 1-37/64 in. (40 mm); selector switches with wing lever knobs require 2-1/4 in.
(57.1 mm) vertical and horizontal minimum spacing and large round legend plates require 1-1/2 in. (38.1 mm) minimum spacing.
Units with Quick Connect Units Having Screw Terminals with Units Having Large Screw Terminals
Terminal Contact Blocks Pressure Plate Contact Blocks with Pressure Plate Contact Blocks
(Typical View) (Typical View) (Typical View)
Dimension A
Push-Pull Push-Pull
Description Push Pilot Sel. or Twist Push Pilot Sel. or Twist
Button Light Switch Cyl. Lock Pot. Release Button Light Switch Cyl. Lock Pot. Release
Units with Quick Connect Terminals Units Having Small Screw Terminals with Pressure Plates
Non-Illuminated 2-1/4 — 2-15/32 3-1/2 2-1/32 2-3/4 2-5/16 — 2-17/32 3-9/16 2-1/32 2-13/16
(57.2) — (62.7) (88.9) (51.6) (69.8) (59) — (64.3) (90.5) (51.6) (71.4)
2-1/4 2-1/4 2-15/32 — — 2-3/4 2-25/32 2-25/32 2-17/32 — — 2-13/16
Full Voltage
(57.2) (57.2) (62.7) — — (69.8) (70.6) (70.6) (64.3) — — (71.4)
Illuminated
2-23/32 2-23/32 2-29/32 — — 3-3/32 2-25/32 2-25/32 2-31/32 — — 3-5/32
Transformer
(69.1) (69.1) (73.8) — — (78.6) (70.6) (70.6) (75.4) — — (80.1)
Units Having Large Screw Terminals with Pressure Plates
Non-Illuminated 2-45/64 — 2-59/64 3-15/16 — 3-13/64
(68.6) — (74.2) (100) — (81.4)
3-11/64 3-11/64 3-23/64 — — 3-13/64
Full Voltage
(80.6) (80.6) (85.3) — — (81.4)
Illuminated
3-11/64 3-11/64 3-23/64 — — 3-35/64
Transformer
(80.6) (80.6) (85.3) — — (90.1)
Bulletin 800MS
y 22.5 mm mounting hole
y Type 13 oiltight
y Square traditional operators
Illuminated
Momentary Operator Gray Bezel Pilot Light Standard Knob Operator Knob Lever Operator
Cat. No. 800MS-XO24A Cat. No. 800MS-Q24 Cat. No. 800MS-24HA2BRA Cat. No. 800MS-24JL2BRA
with Color Insert and Legend Plate with Legend Plate with Legend Plate with Legend Plate
Cat. No. 800MS-WBLR20 Cat. No. 800MS-WBLA10 Cat. No. 800MS-WS00 Cat. No. 800MS-WS00
Non-Illuminated
Momentary Operator Gray Bezel Standard Knob Operator Knob Lever Operator
Cat. No. 800MS-XOB Cat. No. 800MS-HG2BB Cat. No. 800MS-JT2BB
with Legend Plate Potentiometer Unit with Legend Plate with Legend Plate
Cat. No. 800MS-WA119 Cat. No. 800MS-N37 Cat. No. 800MS-WS00 Cat. No. 800MS-WS00
Bulletin 800MB
y 22.5 mm mounting hole
y Type 13 oiltight
y Square backlit operators
Illuminated
Pilot Light Push-to-Test Pilot Light Pilot Light, Dual Lamp Push-to-Test Pilot Light, Dual Lamp
Cat. No. 800MB-CQ24RS Cat. No. 800MB-CPT16G Cat. No. 800MB-DL24GR Cat. No. 800MB-DT24RG
Non-Illuminated
Table of Contents
Specifications................. Refer to Bulletin 800MR Specifications Operators.......................... Consult your local Rockwell Automation sales
office or Allen-Bradley distributor
Bulletin 800MB Push Button Operators
To order Bulletin 800MB push button operators, consult your local Rockwell Automation sales office or Allen-Bradley distributor.
Table of Contents
Description Page Description Page
Specifications ........................................................ 34 Rotary Operators.................................................. 37
Product Selection Modifications and Accessories
Momentary Contact, Non-Illuminated ....... 35 Accessories ......................................................... 39
Momentary Contact, Illuminated ................. 35 Color Lens Caps................................................ 40
Maintained, Illuminated ................................... 35 Lens Caps ............................................................ 40
Pilot Lights............................................................... 35 Diffuser Inserts.................................................... 40
Selector Switches Replacement Lamps ........................................ 40
2-Position ............................................................. 37 Legend Inserts....................................................... 41
3-Position ............................................................. 37 Approximate Dimensions................................. 42
Specifications9
Electrical Ratings
1 A, 125V AC
Maximum Contact Ratings
1 A, 250V AC resistive
1 A, 28V DC resistive
Continuous 5 A (Ith) 1 mA, 5V DC low level
100 mA, 50 mV dry circuit
Mechanical Ratings
File E14840
UL Listed
Guide NKCR
CSA Approved LR1234 (operators), LR2923 (assembled panels)
IEC Compliance IEC 144
Mechanical endurance 1 000 000 cycles
Contact material Gold plate over silver
Contact bounce 3 ms (typical)
Electrical life 200 000 cycles at rated load
Dielectric strength 1000V RMS at sea level
Environment
Temperature range
Note: Operating temperature ranges below +32°F (0°C) are based on the Operating: –20…+45°C (–4…+113°F)
absence of freezing moisture and liquids. Storage: –30…+85°C (–22…+185°F)
NEMA Types 1, 3, 12, and 13; IEC 144, IP65
Construction
1 N.O. - 1 N.C., SPDT
Circuits
Double-break contacts
Gold-plated, solderable, quick connect stabs 0.110 x 0.020 in. or PC
Contact terminals
board/wire wrap pin 0.020 x 0.030 in. (0.210 in. long) terminals
Lamp terminals Tin-plated
9 Performance Data — See Important-3 in the Industrial Controls catalog..
Stab Terminations
Push Buttons and Pilot Lights — Round, Square, and Rectangular Bezel
Push Buttons and Pilot Lights — Round, Square, and Rectangular Bezel
800A – M 2A A 24 C
a b c d e
a b (cont’d) d d (cont'd)
Operator and Termination Type Bezel and Head Type Lamp Type and Voltage Lamp Type and Voltage
Stab Type Termination9 Flush Head Non-Illuminated LED§
Code Description Code Description Code Description Code Description
M Momentary push button 2E Round Non-illuminated — 6L 6V AC/DC
T Maintained push button 2F Square -- supplied without lamp 2L 12V AC/DC
(Blank)
L Pilot light 2G Rectangular 4L 24V AC/DC
Incandescent
PC Pin Type Termination7 0L 120V AC
c Code Description
Code Description Neon³
Lens Cap 06 6V AC/DC
C Momentary push button Code Description
Code Description 12 12V AC/DC
F Maintained push button 10 120V AC
Leave blank if no lens cap 24 24V AC/DC
E Pilot light -- 20 240V AC
or lamp desired (Blank)
b X
Used only when lamp and e
no lens cap is desired
Bezel and Head Type Factory Assembly
A Amber
Extended Head Code Description
B Blue
Code Description Leave blank for no factory
C Clear --
2A Round assembly (Blank)
G Green
2B Square C Completely assembled
R Red‡
2C Rectangular
800A – M 2D A 24 C
a b c d e
a b d d (cont'd)
Operator and Termination Type Bezel and Head Type Lamp Type and Voltage Lamp Type and Voltage
Stab Type Termination9 Code Description Non-Illuminated LED§
Code Description Extended head large Code Description Code Description
2D
M Momentary push button square Non-illuminated — 6L 6V AC/DC
T Maintained push button 2H Flush head large square -- supplied without lamp 2L 12V AC/DC
(Blank)
L Indicating light c 4L 24V AC/DC
Incandescent
PC Pin Type Termination7 Lens Cap 0L 120V AC
Code Description
Code Description Code Description Neon³
06 6V AC/DC
C Momentary push button Leave blank if no lens cap Code Description
-- 12 12V AC/DC
F Maintained push button or lamp desired (Blank) 10 120V AC
24 24V AC/DC
E Indicating light Used only when lamp and 20 240V AC
X
no lens cap is desired
A Amber e
B Blue Factory Assembly
C Clear Code Description
G Green Leave blank for no factory
--
assembly (Blank)
R Red‡
C Completely Assembled
9 0.110 x 0.20 in. solderable stab terminals are compatible with AMP connector Part No. 61060-1 or equivalent.
7 Compatible with PC pin connector Cat. No. 800A-N66. Available in packs of 50.
‡ Red flush head push buttons are not suitable for applications requiring extended head, or other unguarded buttons capable of being operated quickly in
emergencies, and they may not comply with applicable codes or standards.
§ LEDs include internal current limiting resistors.
³ Neon lamps are only available with clear, amber, or red lens cap.
Round Bezel, Knob Operator Square Bezel, Cylinder Lock Rectangular Bezel, Knob Operator
Cat. No. 800A-H2AW Cat. No. 800A-HC2B Cat. No. 800A-G2CW
2-Position Cylinder Lock and Knob Operated Selector Switches
Operator Position Round Square Rectangular
Termination Type Operator Type Operator Function Cat. No. Cat. No. Cat. No.
Stab O X 800A-HC2A 800A-HC2B 800A-HC2C
Key
PC pin X O Maintained in both 800A-GC2A 800A-GC2B 800A-GC2C
Stab O X positions 800A-H2AW 800A-H2BW 800A-H2CW
Knob
PC pin X O 800A-G2AW 800A-G2BW 800A-G2CW
Note: X = Closed/O = Open
Rotary Operators
The rotary operator kit provides a means to actuate rotary switches and potentiometers and maintains consistent panel appearance.
The kit contains all necessary hardware to accommodate potentiometers, or multi-run switches (Type W potentiometers are available through
electronic component distributors or Grayhill Series 50 rotary switch elements). Dimensional requirements of elements must comply with the
switch in figures 1 and 2 shown on this page. Potentiometer or switch not included.
Note: For operator dimensional information, refer to page 42.
Approximate Dimensions
a1 b c d
Selector Switch Information
(Terminal 1…2) X O
(Terminal 3…4) O X
Contact Function: X = Closed/O = Open
a a1 c d (cont'd)
Operator and Termination Type Operator and Termination Type Knob Insert Color7 Optional Key
Standard Knob Selector Switch Cylinder Lock with Stab Code Description Code Description
with Stab Terminals Terminals A Orange 08 Custom key #8
Code Description Code Description B Blue 09 Custom key #9
H Maintained HC Maintained9 G Green 10 Custom key #10
K Spring return from right Cylinder Lock with Pin Terminals R Red 11 Custom key #11
Standard Knob Selector Switch Code Description W White 12 Custom key #12
with Pin Terminals
GC Maintained9 Y Yellow 13 Custom key #13
Code Description
-- Key (Blank) 14 Custom key #14
G Maintained b
d 15 Custom key #15
R Spring return from right Bezel Type
16 Custom key #16
Potentiometer Operators Code Description Optional Key
17 Custom key #17
Code Description 2A Round Code Description
18 Custom key #18
Potentiometer, rotary 2B Square Blank Standard key
P switch operator (with knob 19 Custom key #19
2C Rectangular 01 Custom key #1
only) 20 Custom key #20
2D Large square 02 Custom key #2
21 Custom key #21
03 Custom key #3
22 Custom key #22
04 Custom key #4
23 Custom key #23
05 Custom key #5
24 Custom key #24
06 Custom key #6
3-Position Selector Switches 07 Custom key #7
Terminal Configuration for Terminal Configuration for Terminal Dimensions Selector Operation
800A-JB, JJ 800A-JH, JR, JL
a a (cont'd) b c
Operator and Termination Type Operator and Termination Type Bezel Type Knob Insert Color7
Standard Knob Selector Switch Standard Knob Selector Switch Code Description Code Description
with Solder Lug Terminals‡ with Solder Lug Terminals‡ 2A Round A Orange
(one pole per position) (two poles per position)
2B Square B Blue
Code Description Code Description
2C Rectangular G Green
JB Spring return — both JH Maintained
2D Large square R Red
JJ Maintained JR Spring return right
W White
JL Spring return left
Y Yellow
Note: Low security locks. Key interchangeability possible.
9 Lock in left or right position. Key removable in either left or right position.
7 Special colors — Selector switches and rotary kits are factory assembled with a white color insert as standard. Other colors are available factory assembled at
no additional charge if ordered in quantities of five or more.
‡ Solder lug termination dimensions shown above are smaller than standard Bulletin 800A stab terminations.
Rotary Operator Assembly Tool Lamp Installation/Removal Tool Custom Legend Kit
Lens Caps
Replacement lens caps are available. Lens caps are packaged in multiples of five. Lens caps must be ordered in multiples of five only.
Example: (5) Catalog Number 800A-N20A.
Round Square Rectangular
Color Cat. No. Cat. No. Cat. No.
Amber 800A-N20A 800A-N20A 800A-N20A
Blue 800A-N20B 800A-N20B 800A-N20B
Clear 800A-N20C 800A-N20C 800A-N20C
Green 800A-N20G 800A-N20G 800A-N20G
Red 800A-N20R 800A-N20R 800A-N20R
Replacement Lamps
Use the table below to order replacement lamps. The cat. no. as listed represents one lamp. Lamps can only be ordered in multiples of ten.
Example: (20) six volt lamps would be ordered as (20) Catalog Number 800M-N15. White LEDs operating on 24V AC/DC are available.
Consult your local Allen-Bradley distributor.
Lamp Type Operator Voltage ANSI Number Cat. No.
Full voltage and transformer 6.3 86 800M-N15
Incandescent9 14 73 800M-N16
Full voltage
24 85 800M-N17
120 — 800A-N110
Neon7 —
240 — 800A-N120
6 AC/DC — § 800T-N60x
12 AC/DC — § 800T-N61x
LED‡ Full voltage
24 AC/DC — § 800T-N62x
120 AC — § 800T-N64x
9 Wedge base (ANSI #85) incandescent lamps are subject to significantly shortened lamp life during 24V DC operation. Use wedge base LEDs for longer lamp
life.
7 Resistors are supplied with unit and must be connected in series with lamp. 120V neons use a 47K, 1/4 watt resistor, 240V neons require two 47K, 1/4 watt
resistors; typical forward current 1.2 mA.
‡ LEDs have built-in current limiting resistors.
§ To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green or Red.
Legend Markings
Large square selector switches and rotary operators may be engraved per the diagram below. Specify cat. no. and custom engraving.
Character dimensions in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
Shipping Wt. for Rectangular Push Button Shipping Wt. for Rectangular Selector Switch
0.71 oz. (20 gm) 1.34 oz. (38 gm)
Wiring Diagrams
(See Applicable Codes and Laws)
800C – P 02 Z97
a b
800C – P 02 H K
a b c d e f g h i j
Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 Pos. 7 Pos. 8 Pos. 9 Pos. 10
a b…j b…j (continued)
Enclosure — Number of Holes Operator Type Operator Type
Code Description Code Description Code Description
02 2-Hole Station White Button, No Text (with N.O. 1-Speed "Up" Button (with 1 N.O. and
1 H
03 3-Hole Station contact block) 1 N.C. contact blocks)§
Black Button, No Text (with N.O. 2-Speed "Up" Button (with 2 N.O. and
05 5-Hole Station 2 J
contact block) 1 N.C. contact blocks)§
07 7-Hole Station Green Button, No Text (with N.O. 1-Speed "Down" Button (with 1 N.O.
3 K
08 8-Hole Station contact block) and 1 N.C. contact blocks)§
10 10-Hole Station Red Button, No Text (with N.C. contact 2-Speed "Down" Button (with 2 N.O.
4 L
block) and 1 N.C. contact blocks)§
12 12-Hole Station ‡
Yellow Button, No Text (with N.O. 1-Speed "Left" Button (with 1 N.O. and
5 M
contact block) 1 N.C. contact blocks)§
Blue Button, No Text (with N.O. contact 2-Speed "Left" Button (with 2 N.O. and
6 N
block) 1 N.C. contact blocks)§
Red Momentary Mushroom (with N.C. 1-Speed "Right" Button (with 1 N.O.
A P
contact block) and 1 N.C. contact blocks)§
9 Housings supplied with cable sleeve, hanger Twist-to-Release E-Stop (with N.C. 2-Speed "Right" Button (with 2 N.O.
ring, cable clamp,wire guides, contact block B Q
contact block) and 1 N.C. contact blocks)§
latches, gasket, and screws.
Twist-to-Release E-Stop with Indicator 1-Speed "Forward" Button (with 1 N.O.
7 Code Z is valid in Parameter "b" only. C R
(with N.C. contact block) and 1 N.C. contact blocks)§
‡ 12-hole enclosures are available as a housing
only. Contact your local Allen-Bradley 0-1 Key Selector Switch (with N.O. 2-Speed "Forward" Button (with 2 N.O.
D S
distributor for custom configuration. contact block) and 1 N.C. contact blocks)§
§ N.C. contact block used for interlock. 1-0-2 Key Selector Switch (with 2 N.O. 1-Speed "Reverse" Button (with 1 N.O.
E T
contact blocks) and 1 N.C. contact blocks)§
0-1 Knob Selector Switch (with N.O. 2-Speed "Reverse" Button (with 2 N.O.
F U
contact block) and 1 N.C. contact blocks)§
1-0-2 Knob Selector Switch (with 2 V Hole Plug
G
N.O. contact blocks) Z Empty Housing
Specifications
Pendant Station Specifications
cULus, CE, UL Listed (File No. E14840;
Certifications
Guide No. NKGR)
UL 508, CSA 22.2 #14, EN/IEC 947-5-1,
Standards
EN418 (E-Stop), VDE 0660 part 200
Ingress Protection IP65/NEMA Type 3/3R (station), IP2X (contacts)
Mechanical Design Life 1 000 000 cycles (buttons) - 300 000 cycles (E-Stops)
Electrical Ratings A600, Q600, AC-15, DC-13, Ith = 16 Amps AC
Operating Temperature –25…+50 °C (–13…+122 °F)
Storage Temperature –40…+70 °C (–40...+158 °F)
800C – F 3
a b
a b
Operator Type Color Cap
Code Description Code Description
F Flush 1 White
2 Black
3 Green
4 Red
5 Yellow
6 Blue
800C – F 1 41
a b c
a b c
Operator Type Color Cap Symbol
Code Description Code Description Code Description
F Flush 1 White 41 1-speed "Up" button 9
9 Black symbol on white cap. 2 Black 42 1-speed "Down" button 7
7 White symbol on black cap. 43 1-speed "Left" button 7
44 1-speed "Right" button 9
45 1-speed "Forward" button 9
46 1-speed "Reverse" button 7
51 2-speed "Up" button 9
52 2-speed "Down" button 7
53 2-speed "Left" button 7
54 2-speed "Right" button 9
55 2-speed "Forward" button 9
56 2-speed "Reverse" button 7
Accessories/Replacement Parts
Pkg.
Description Quantity Cat. No.9
2-hole pendant housing 800C-P02Z
3-hole pendant housing 800C-P03Z
5-hole pendant housing 800C-P05Z
7-hole pendant housing 1 800C-P07Z
8-hole pendant housing 800C-P08Z
10-hole pendant housing 800C-P10Z
12-hole pendant housing 800C-P12Z
9 Housings supplied with cable sleeve, hanger ring, cable clamp, wire guides,
contact block latches, gasket, and screws.
Contact Block97
N.O.M.S. 1 800C-X20M
Note: Sold only in multiples of 10.
Hole Plug
Note: Sold only in multiples of 10. Order (quantity of) 10 to receive 10 800C-AH2
one package of 10 pieces.
Mounting Ring
Note: Sold only in multiples of 10. Order (quantity of) 10 to receive 10 800C-ARM
one package of 10 pieces.
Dimensions are in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes.
Approximate Dimensions
800C-P02… 800C-P03… 800C-P05…-P12