Professional Documents
Culture Documents
Amodel
Amodel
Polyphthalamide www.ulprospector.com
Solvay Specialty Polymers
Technical Data
Product Description
Amodel® AS-4133 HS is a 33% glass reinforced, lubricated, heat stabilized grade of polyphthalamide (PPA) that offers fast cycle times and
moldability in hot water molds. Testing conducted on samples dry as molded and samples conditioned to 50% relative humidity in accordance
with ISO-1110, Accelerated Method. Typical applications include electrical and electronic components especially for automotive systems.
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL
assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product
or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The
content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.
Amodel® AS-4133 HS
Polyphthalamide
Solvay Specialty Polymers www.ulprospector.com
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL
assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product
or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The
content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.
Amodel® AS-4133 HS
Polyphthalamide
Solvay Specialty Polymers www.ulprospector.com
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL
assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product
or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The
content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.
Amodel® AS-4133 HS
Polyphthalamide
Solvay Specialty Polymers www.ulprospector.com
Injection Notes
Injection Rate: 3 to 4 in/sec
Holding Pressure: 50% of injection pressure
Storage:
• Amodel® compounds are shipped in moisture-resistant packages at moisture levels according to specifications. Sealed, undamaged bags
should be preferably stored in a dry room at a maximum temperature of 50°C (122°F) and should be protected from possible damage. If
only a portion of a package is used, the remaining material should be transferred into a sealable container. It is recommended that Amodel®
resins be dried prior to molding following the recommendations found in this datasheet and/or in the Amodel® processing guide.
Notes
1 These links provide you with access to supplier literature. We work hard to keep them up to date; however you may find the most current literature
from the supplier.
2 A UL Yellow Card contains UL-verified flammability and electrical characteristics. UL Prospector continually works to link Yellow Cards to
individual plastic materials in Prospector, however this list may not include all of the appropriate links. It is important that you verify the association
between these Yellow Cards and the plastic material found in Prospector. For a complete listing of Yellow Cards, visit the UL Yellow Card Search.
3 Typical properties: these are not to be construed as specifications.
4 1500 hr
5 These flammability ratings are not intended to reflect hazards presented by these or any other materials under actual fire conditions.
6 Transmittance for natural grade
The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL
assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product
or material selection information is validated with the manufacturer. This website provides links to other websites owned by third parties. The
content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.