Professional Documents
Culture Documents
Yamaha S90es Service
Yamaha S90es Service
Yamaha S90es Service
CONTENTS(目次)
SPECIFICATIONS(総合仕様)........................................................... 3
PANEL LAYOUT(パネルレイアウト)................................................ 5
DISASSEMBLY PROCEDURE(分解手順)........................................ 7
LSI PIN DESCRIPTION(LSI 端子機能表)....................................... 23
IC BLOCK DIAGRAM (IC ブロック図)........................................... 31
CIRCUIT BOARDS(シート基板図)................................................ 33
TEST PROGRAM(テストプログラム)...................................... 47/69
DATA BACKUP(データのバックアップ)........................................ 94
OS UPDATE(OS のアップデート)................................................. 95
SYSTEM FLOW CHART (After turning on the power) ...................... 96
(電源立ち上げシーケンス)............................................................... 97
DISPLAY MESSAGES(ディスプレイメッセージ).................. 98/100
MIDI IMPLEMENTATION CHART
(MIDI インプリメンテーションチャート)............................. 102
MIDI DATA FORMAT ....................................................................... 104
PARTS LIST
BLOCK DIAGRAM(ブロックダイアグラム)
CIRCUIT BOARD LAYOUT(ユニットレイアウト)
WIRING
KEY MATRIX
OVERALL CIRCUIT DIAGRAM(総回路図)
SY 001742
20050720-273000
HAMAMATSU, JAPAN
Copyright (c) Yamaha Corporation. All rights reserved. PDF-K9952 M
I ’05.09
S90ES
IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that
basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the
users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in per-
sonal injury, destruction of expensive components and failure of the product to perform as specified. For
these reasons, we advise all Yamaha product owners that all service required should be performed by an
authorized Yamaha Retailer or the appointed service representative.
IMPORTANT: This presentation or sale of this manual to any individual or firm does not constitute authorization, certifica-
tion, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any
form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and
service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefor, inevitable and
changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this
bus).
IMPORTANT: Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to
the unit.
2
S90ES
■ SPECIFICATIONS(総合仕様)
Tone Generator Tone Generator AWM2 (complying with the Modular Synthesis Plug-in System)
block Maximum polyphony 128 notes + the polyphony of the Plug-in Boar d (if installed)
Multi Timbral Capacity 16 Internal Parts + 3 Plug-in Boards + Audio Input Part(s) (A/D, mLAN*)
* 4 stereo parts
Wave 228MB (when converted to 16-bit linear for mat), 1,935 waveforms
Multi User: 64
Filter 18 types
Effects Reverb x 20 types, Chorus x 49 types, Inser tion (A, B) x 117 types x 8 blocks, Master
Effect x 8 types, Master Equalizer (5 bands), Par t EQ (3 bands, stereo), Plug-in
Insertion (available when the PLG100-VH has been installed to slot 1)
Sequence Software For Windows® : Cubase SX 3, SQ01 V2, SONAR 4, S90 ES/MOTIF ES/MOTIF-RACK
compatible with the ES/MOTIF-RACK Multi Part Editors.
Remote Control function For Macintosh® : Cubase SX 3, Logic Pro 7, Digital Performer 4.52, S90 ES/MOTIF ES/
MOTIF-RACK ES/MOTIF-RACK Multi Part Editors
* Functions to be controlled by the S90 ES differ depending on the software you use.
Controllers Pitch Bend wheel, Modulation wheel, Assignable Control sliders (4), Data dial
Jack and Terminals OUTPUT L/MONO, R (standard phone jack), ASSIGNABLE OUTPUT L, R (standard
phone jack), A/D INPUT L, R (standard phone jack), PHONES (standard stereo phone
jack), FOOT CONTROLLER 1, 2, FOOT SWITCH x 2 (SUSTAIN, ASSIGNABLE),
BREATH, MIDI IN/OUT/THRU, USB (TO HOST, TO DEVICE), AC INLET
Dimensions, Weight 1,472 (W) x 385 (D) x 163 (H) mm, 22.5 kg
Accessories AC Power cord, Owner’s Manual, Data List, sticker label for optional
mLAN16E.
3
S90ES
鍵盤 88鍵バランスドハンマー鍵盤(イニシャルタッチ/アフタータッチ付)
音源部 音源方式 AWM2 (Modular Synthesis Plug-in System対応)
最大同時発音数 内蔵128音+プラグインボードの最大同時発音数
マルチティンバー数 内蔵音源16パート+3プラグインボード、オーディオ入力パート(A/D、mLAN*)
*4ステレオパート
波形メモリー 228MB相当(16bitリニア換算)、1935ウェーブフォーム
ボイス数 プリセット: 512ノーマルボイス+ 64ドラムキット
GM: 128ノーマルボイス+1ドラムキット
ユーザー: 128×2 (バンク1: オリジナル、バンク2: プリセットからのピックアップ)
ノーマルボイス+32ドラムキット
プラグインボイス数 PLG150-AN/DX/PF/DR/PC用プリセット: 各64音色
PLG150-VL用プリセット: 192音色
ユーザー: プラグインスロットごとに64音色
パフォーマンス数 ユーザー: 128 (最大4パート)
マルチ数 ユーザー: 64
フィルター 18タイプ
エフェクター リバーブ×20タイプ、コーラス×49タイプ、インサーション(A、B)×117タイプ×8系統、
マスターエフェクト×8タイプ、マスターEQ (5バンド)、パートEQ (3バンド、ステレオ)、
プラグインインサーション(スロット1にPLG100-VH装着時)
プラグインボード増設スロット Modular Synthesis Plug-in Boardスロット×3
シーケンサー部 シーケンスプレイ SMF Format 0 (再生のみ)
BPM 1∼300
チェーンステップ数 100
アルペジエーター プリセット×1,787タイプ
ユーザー×256タイプ(MOTIF ESのユーザーアルペジオをロードした場合のみ使用可)
※MIDIシンク、MIDI送受信チャンネル、ベロシティーリミット、ノートリミット設定可
その他 マスターモード設定数 ユーザー:128設定
※4ゾーン(マスターキーボード設定)、アサイナブルスライダー設定、プログラムチェンジテーブル
リモート対応ソフトウェア <Windows> SOL2、XGworks ST、Cubase SX 3、SQ01 V2、SONAR 4、S90 ES/
MOTIF ES/MOTIF-RACK ES/MOTIF-RACK Multi Part Editor
<Macintosh > Cubase SX 3、Logic Pro 7、Digital Performer 4.52、S90 ES/
MOTIF ES/MOTIF-RACK ES/MOTIF-RACK Multi Part Editor
※各ソフトウェアの機能によって、リモートコントロールできる内容が異なります。
主な操作子 ピッチベンドホイール×1、モジュレーションホイール×1、
アサイナブルコントロールスライダー×4、データダイアル×1
ディスプレイ 240×64ドットグラフィックLCD (バックライト付)
接続端子 OUTPUT L/MONO, R (標準フォーンジャック)、ASSIGNABLE OUTPUT L, R
(標準フォーンジャック)、A/D INPUT L, R(標準フォーンジャック)、
PHONES (ステレオ標準フォーンジャック)、FOOT CONTROLLER 1, 2、
FOOT SWITCH×2 (SUSTAIN, ASSIGNABLE)、BREATH、MIDI IN/OUT/THRU、
USB (TO HOST , TO DEVICE)、AC INLET
消費電力 27W (本体のみ14W)
寸法・質量 1,472 (W)×385 (D)×163 (H) mm、22.5 kg
付属品 電源コード、2P-3P変換器、保証書、取扱説明書、データリスト、mLAN16E用シール
4
S90ES
■ PANEL LAYOUT(パネルレイアウト)
● TOP PANEL(トップパネル)
y o !0 !4 !2 !3 !8 @2 @7 @5
PAN/SEND
MODE PROGRAM
PAN REVERB CHORUS TEMPO
EQ LOW LOW MID HIGH MID HIGH FAVORITES A. PIANO KEYBOARD ORGAN GUITAR/ BASS STRINGS BRASS REED/PIPE
PLUCKED
MULTI/
VOLUME 1 VOLUME 2 VOLUME 3 VOLUME 4 SEQ PLAY FILE UTILITY A B C D E F G H
EFFECT
F1 F2 F3 F4 F5 F6 EXIT ENTER REMOTE BYPASS ARPEGGIO 9 10 11 12 13 14 15 16 MUTE
EXECUTE SOLO
r t u i !1 !6 !5 !7 !9 @0 @1 @3 @4 @6
PAN/SEND
MODE PROGRAM
PAN REVERB CHORUS TEMPO
EQ LOW LOW MID HIGH MID HIGH FAVORITES A. PIANO KEYBOARD ORGAN GUITAR/ BASS STRINGS BRASS REED/PIPE
PLUCKED
MULTI/
VOLUME 1 VOLUME 2 VOLUME 3 VOLUME 4 SEQ PLAY FILE UTILITY A B C D E F G H
EFFECT
F1 F2 F3 F4 F5 F6 EXIT ENTER REMOTE BYPASS ARPEGGIO 9 10 11 12 13 14 15 16 MUTE
EXECUTE SOLO
A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B5 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7
we q
q Keyboard q 鍵盤
w [PITCH] Bend Wheel w [PITCH] (ピッチベンド)ホイール
e [MODULATION] Wheel e [MODULATION] (モジュレーション)ホイール
r [MASTER VOLUME] Slider r [MASTER VOLUME] (マスターボリューム)スライダー
t (Control Sliders 1 - 4) t (コントロールスライダー 1 ∼ 4)
y [PAN/SEND],[TONE],[ARP FX],[EQ],[VOLUME] y [PAN/SEND],[TONE],[ARP FX],[EQ],[VOLUME]
(Control function buttons) (コントロールファンクション)ボタン
u LCD contrast control u LCD コントラスト調節ノブ
i [F1]-[F6] (Function) buttons i [F1]-[F6] (ファンクション)ボタン
o [SF1]-[SF2] (Sub Function) buttons o [SF1]-[SF2] (サブファンクション)ボタン
!0 LCD (液晶ディスプレイ)
!0 LCD (Liquid Crystal Display)
!1 [INFORMATION] (インフォメーション)ボタン
!1 [INFORMATION] button
!2 データダイアル
!2 Data dial
!3 [INC/YES] (インク/イエス)ボタン
!3 [INC/YES] button
!4 [DEC/NO] (デック/ノー)ボタン
!4 [DEC/NO] button
!5 カーソルボタン
!5 Cursor buttons !6 [EXIT] (エグジット)ボタン
!6 [EXIT] button !7 [ENTER] (エンター)ボタン
!7 [ENTER] button !8 MODE (モード)ボタン
!8 MODE buttons !9 [REMOTE] (リモート)ボタン
!9 [REMOTE] button @0 [EFFECT BYPASS] (エフェクトバイパス)ボタン
@0 [EFFECT BYPASS] button @1 [ARPEGGIO] (アルペジオ)ボタン
@1 [ARPEGGIO] button @2 バンクボタン
@2 BANK buttons @3 グループ [A] ∼ [H] ボタン
@3 GROUP [A]-[H] buttons @4 ナンバー [1] ∼ [16] ボタン
@4 NUMBER [1]-[16] buttons @5 [CATEGORY SEARCH](カテゴリーサーチ)ボタン
@5 [CATEGORY SEARCH] button @6 [TRACK SELECT], [MUTE] (トラックセレクト、
@6 [TRACK SELECT], [MUTE] buttons ミュート)ボタン
@7 SLOT 1-3 lamps @7 SLOT(スロット)1 ∼ 3 ランプ
5
S90ES
● REAR PANEL(リアパネル)
@8 #0 #1 #2 #3 #4 #5 $1
R L R L/MONO R L
@9 #6 #7 #8 #9 $0
6
S90ES
■ DISASSEMBLY PROCEDURE(分解手順)
* Refer to the attached paper <P.2> for “S90ES * シートのレイアウトについては、別紙 <P.2>
CIRCUIT BOARD LAYOUT”. “S90ESユニットレイアウト”を参照して下さい。
(Fig.1) (Fig.2)
[100]
[A] [A]
(Fig.3)
[100]: CUP Head Screw 5.0X18 MFZN2B3 (WE986800) 小ネジ+CUP
1-2 Remove the eighteen (18) screws marked [100]. 1-2. [100] のネジ 18 本を外します。(Fig.3)
(Fig.3) 途中でパネルが開くのを防ぐため、[A] のネジ
To prevent the panel from opening suddenly in the 2 本を最後に外してください。(Fig.3)
middle of disassembling, make sure to remove two このとき、片手でパネルを押さえながらネジを
(2) screws marked [A] at last. (Fig.3) 外すと、より安全です。(Fig.4)
Then, steady the panel with other hand for added
safety. (Fig.4)
7
S90ES
Stay
(ステイ)
(Fig.4) (Fig.5)
Service Tool(V6295700) ステイ
1-3 Turn the product forward and lay it right side up. 1-3. 本体を前方に倒し、水平にします。
1-4 Open the control panel and support it with a jig 1-4. コントロールパネルを開き、治具のステイ
stay (V6295700). (Fig.5) (V6295700) で固定します。(Fig.5)
[42]
Control Panel
(コントロールパネル)
(Fig.6)
[42]: Bind Head Screw 4.0X14 MFZN2W3 (WE968700) 小ネジ+BIND
8
S90ES
[204]
[84]
Top View
Power Suply Unit
(電源ユニット)
[70c] [70e]
Connector Assembly
PLG support
(インレット束線Ass'y)
(PLGサポート)
PNB-PW
DM Shield
(DMシールド)
Felt
(フェルト)
[80d]
[92]
[82] DM Shield Locking portion of Spacer [30e]
(DMシールド) (スペーサーのロック)
[22B] [32B]
[22A] [32A]
[22C] [32C]
[22D] [32D]
PNA-AN Spacer
Connector Assembly (スペーサー)
(ホイール束線) Side Cover R Assembly
(腕木 R Ass'y)
Side Cover L Assembly
(腕木 L Ass'y)
(Fig.9)
[22]: Bind Head Tapping Screw-B 3.0X6 MFZN2B3 (WF028600) Bタイト+BIND
[30e]: Bind Head Tapping Screw-B 3.0X8 MFZN2B3 (WE774400) Bタイト+BIND
[32]: Bind Head Tapping Screw-B 3.0X6 MFZN2B3 (WF028600) Bタイト+BIND
[80d]: Bind Head Tapping Screw-B 3.0X8 MFZN2B3 (WE774400) Bタイト+BIND
[82]: Bind Head Screw 3.0X6 MFZN2B3 (WE878300) 小ネジ+BIND
[92]: Bind Head Tapping Screw-B 3.0X6 MFZN2B3 (WF028600) Bタイト+BIND
9
S90ES
(Fig.11)
[180]
PN Support
PN Support
(PNサポート)
(PNサポート)
(Fig.13)
[22]: Bind Head Tapping Screw-1 3.5X10 MFZN2W3 (WE970800) TP#1+BIND
[42]: Bind Head Screw 4.0X14 MFZN2W3 (WE968700) 小ネジ+BIND
[52]: Bind Head Tapping Screw-1 3.5X10 MFZN2W3 (WE970800) TP#1+BIND
[40f]: Bind Head Tapping Screw-B 3.0X6 MFZN2B3 (WF028600) Bタイト+BIND
[50k]: Bind Head Tapping Screw-B 3.0X6 MFZN2B3 (WF028600) Bタイト+BIND
[86]: Bind Head Tapping Screw-B 3.0X6 MFZN2B3 (WF028600) Bタイト+BIND
10
S90ES
11
S90ES
12
S90ES
[20c] [30c]
(Fig.14)
[20c]: Bind Head Tapping Screw-1 4.0X12 MFZN2W3 (WE971800) TP#1+BIND
[30c]: Bind Head Tapping Screw-1 4.0X12 MFZN2W3 (WE971800) TP#1+BIND
13
S90ES
(Fig.15)
(Fig.16)
14
S90ES
[32]
(Fig.17)
[32]: Bind Head Tapping Screw-1 3.5X12 MFZN2B3 (WE971400) TP#1+BIND
Front Rail
[34] (口棒) [34]
(Fig.18)
[34]: Bind Head Tapping Screw-B 3.0X6 MFZN2B3 (WF028600) Bタイト+BIND
Keyboard Assembly
(鍵盤Ass'y)
Master
(マスター)
Slave
(スレーブ)
Push
V-Spring Assembly
(VバネAss'y)
(Fig.19)
Service Tool(工具)(VB299400) 3X25 バインド S タイト
(Fig.20) (Fig.21)
15
S90ES
(Fig.22) (Fig.23)
Keyboard Assembly
(鍵盤Ass'y)
[P60]
Master
(マスター)
Slave
GHDPC (スレーブ)
[P60]
PC Sensor spring
Connector Assembly GHDPC (PC センサーバネ) Sensor sheet holder PC Sensor spring
(コネクターAss'y) Sensor sheet holder (センサーシートホルダー) (PC センサーバネ)
(センサーシートホルダー)
(Fig.24) (Fig.25)
[P60]: Bind Head Tapping Screw-P 3.0X8 MFZN2BL (EP630220) [P60]: Bind Head Tapping Screw-P 3.0X8 MFZN2BL (EP630220)
+バインドPタイト +バインドPタイト
16
S90ES
20b-3 Remove the slave string from the V-spring assem- 20b-3. V バネ Ass'y からスレーブストリングを外しま
bly. (Fig.20, 21) す。(Fig.20, 21)
20b-4 Remove the slave string from the PC sensor spring. 20b-4. PC センサーバネからスレーブストリングを外
(Fig.22, 23) します。(Fig.22, 23)
20b-5 Disconnect the connector assembly from the 20b-5. GHDPC シートから中継束線 3P を外します。
GHDPC circuit board. (Fig.24) (Fig.24)
20b-6 Remove the three (3) screws marked [P60] to 20b-6. [P60] のネジ 3 本を外し、GHDPC シートを外し
remove the GHDPC circuit board. (Fig.24) ます。(Fig.24)
20b-7 Remove the PC sensor spring from the sensor sheet 20b-7. センサーシートホルダーから PC センサーバネ
holder. (Fig.24) を外します。(Fig.24)
* When removing the PC sensor spring and the * PC センサーバネと GHDPC シートを外すとき
GHDPC circuit board, hold the sensor sheet holder は、センサーシートホルダーの切り欠き部分を
by around its slits. (Fig.24) 持ってください。(Fig.24)
(Fig.27)
(Fig.26)
Master strings
V spring Assembly
(Fig.28) (Fig.29)
17
S90ES
(Fig.30)
(Fig.31)
Adhesive Tape
(両面テープ)X1
(Fig.32) (Fig.32-1)
18
S90ES
[260A] x 7
[260A] x 7
(Fig.33)
[260]: Bind Head Tapping Screw-P 3.0X10 MFZN2W3 (WF001000) Pタイト+バインド
[262]: PW Head Tapping Screw-P 3.0X10-10 MFZN2W3 (WF765500) Pタイト+ PWH
19
S90ES
White Key
Thin Metal Plate etc. (白鍵)
(薄い金尺等)
[C]
[D]
[A] Spring
(スプリング)
Triangle Mark
(三角マーク) 丸棒
[B] (Rod : TX000670)
(Fig.34) (Fig.35)
Spring
(スプリング) Stopper L88 Hammer, White Key
(ストッパーL88) (ハンマー白鍵)
Hook
(フック)
(Fig.36) (Fig.37)
Stopper L88
(ストッパーL88)
Slit
(切り込み)
White Key [E]
(白鍵)
Frame
(フレーム)
(Fig.38)
Upside
(上側)
Key Spring
Key Guide (スプリング)
[F] (キーガイド)
Spring
(スプリング) (Fig.40)
Frame
(フレーム)
Hook
(フック)
(Fig.39)
21
S90ES
22
S90ES
23
S90ES
25
S90ES
26
S90ES
27
S90ES
28
S90ES
PIN PIN
NAME I/O FUNCTION NAME I/O FUNCTION
NO. NO.
1 S/S - Soft start condenser connection 17 N/C - Non-connection (not connected internally)
2 F/B OCL- - F/B Over-current -ve detect at external resistance detection 18 VDD I MOSFET power supply
3 OCL+ - Over-current +ve detect at external resistance detection 19 VDD I MOSFET power supply
4 GND - Control circuit GND 20 VDD I MOSFET power supply
5 N/C - Non-connection (not connected internally) 21 VDD I MOSFET power supply
6 Vcc - Control circuit power supply 22 N/C - Non-connection (not connected internally)
7 N/C - Non-connection (not connected internally) 23 VG - MOSFET gate
8 Vboot - MOSFET drive circuit power supply 24 N/C - Non-connection (not connected internally)
9 N/C - Non-connection (not connected internally) 25 VB - MOSFET drive circuit power supply
10 N/C - Non-connection (not connected internally) 26 GND - Control circuit GND
11 VOUT O Output 27 3.3V/5V - 3.3V/5V output select
12 VOUT O Output 28 Vref - Internal reference voltage output
13 VOUT O Output 29 N/C - Non-connection (not connected internally)
14 VOUT O Output 30 ampOUT - Internal error amplifier output
15 N/C - Non-connection (not connected internally) 31 N/C - Non-connection (not connected internally)
16 P.GND - MOSFET drive circuit GND 32 amp- - Internal error amplifier inverted output
29
S90ES
30
S90ES
1A 1 14 Vcc
1A 1 1 VDD
1OE 1 14 Vcc
1B 2 13 4B
1Y 2 2 6A
A1 2 13 4OE
1Y 3 12 4A
2A 3 3 6Y
Y1 3 12 A4
2A 4 11 4Y
2OE 4 11 Y4 2Y 4 4 5A
2B 5 10 3B
A2 5 10 3OE 3A 5 5 5Y
Y2 6 9 A3 3Y 6 6 4A 2Y 6 9 3A
1B 2 13 4B A1 2 19 G +DC Voltage
Output A 1 +V 8
Supply
1Y 3 12 4A A2 3 18 B1 Inverting
2 7 Output B
Input A - +
2A 4 11 4Y A3 4 17 B2 Non-Inverting 3 6
Inverting
Input A + - Input B
A4 5 16 B3 -DC Voltage Supply 4 -V 5 Non-Inverting
2B 5 10 3B
Input B
2Y 6 9 3A A5 6 15 B4
A6 7 14 B5
GND 7 8 3Y
A7 8 13 B6
A8 9 12 B7
GND 10 11 B8
G
1A 2 A G 15 2G
A OUTPUT 1 8 +V Output A 1 +V 8
+DC Voltage
Supply 1B 3 B
A 14 2A
A -INPUT
A Inverting
2 7 B OUTPUT 2 7 Output B
- + Input A - + 4 B
1Y0 Y0 13 2B
B Non-Inverting Inverting
A +INPUT 3 6 B -INPUT 3 6
+ - Input A + - Input B
1Y1 5 Y1 Y0 12 2Y0
GND 4 5 B +INPUT GND 4 5 Non-Inverting
Input B 6 Y1 11
1Y2 Y2 2Y1
1Y3 7 Y3 Y2 10 2Y2
Y3
GND 8 9 2Y3
31
S90ES
LM3525MX-H (X3119A00)
USB Power Switch
DM: IC032 IN 7 8 OUT
EN 1 8 OUT
FLAG 2 7 IN
Error FET
GND 3 6 OUT FLAG 2 Detect Drive
and
NC 4 5 NC EN 1
Shutdown
Control
Vin
MD5001T (X6129A00) START UP
1
ON/OFF
Step-down DC/DC Controller R/C 2
CONTROL
START=4.3V
STOP=3.8V
BANDGAP
DM: IC041 Vref=4.2V+/-5%
100°C 150°C UVLO OCL COMP
Vref TSD +
190uA
LATCH -
OSC 3 OSC S
Vref 1.8V R Q
0.8V
2uA
Vin 1 8 VOUT
+
S/S 4 - L/S
R/C 2 7 amp- -
8
OSC 3 6 ampout Vout
6
S/S 4 5 GND ampout ERROR AMP
Vref
0.8V +
-
UVP COMP TIMER COMP
7 - -
amp-
+ +
0.65V
3V
5
GND
32
S90ES
■ CIRCUIT BOARDS(シート基板図)
CONTENTS(目次)
● DM Circuit Board (X6083C0) ........................................................................................ 34
33
S90ES
● DM Circuit Board A
MIDI
to PNB-PW CN200 USB USB
TO DEVICE TO HOST THRU OUT IN
to PNA-PN CN5
(OPTION)
to PLUG IN3
to PLUG IN2
to PLUG IN1 to PNA-PN CN2
to LCD
to PNA-PN CN1
Not installed
A'
Component Side(部品側)
34
S90ES
to PNA-AN
CN101
FOOT SWITCH FOOT CONTROLLER
to Wheel Assembly
to mLAN16E Card (OPTION)
A'
Component Side(部品側)
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
35
S90ES
● DM Circuit Board
B'
Pattern Side(パターン側)
2NA-WE26060 1
36
S90ES
B'
Pattern Side(パターン側)
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
37
S90ES
to DM CN8
to GHD_EBUS L CN1 to PNB-PN CN1
PAN/SEND
to DM CN1
TONE
APR/FX
VOLUME
EQ
to LCD
to DM CN14
C'
Component Side(部品側)
2NA-WE26070 4
38
S90ES
(Contrast)
F1 F2 F3 F4 F5 F6
C'
Component Side(部品側)
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
39
S90ES
to PNA-PN CN4
D
A
USER1
DEC/NO INC/YES
UP
EDIT JOB STORE 1
< >
DOWN
A'
D'
Component Side(部品側)
2NA-WE26080 3
40
S90ES
D
A
CATEGORY
PRE1 PRE2 PRE3 PRE4 GM PLG1 PLG2 PRG3 SEARCH
A B C D E F G H
1 2 3 4 5 6 7 8 TRACK
SELECT
9 10 11 12 13 14 15 16 MUTE
A'
D'
Component Side(部品側)
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
41
S90ES
Component Side(部品側)
Component Side(部品側)
to GHD-EBUS L-CN4
Component Side(部品側)
PNB-PW: 2NA-WE26080 3
GHDPC: 2NA-V677460
Note: See parts list for details of circuit board component parts. MK SUB: 2NA-V658810
注:シートの部品詳細はパーツリストをご参照ください。
42
●
A
SW108 SW106 SW104 SW102 SW100 SW98 SW96 SW94 SW92 SW90 SW88 SW86 SW84 SW82 SW80 SW78 SW76 SW74 SW72 SW70
SW107 SW105 SW103 SW101 SW99 SW97 SW95 SW93 SW91 SW89 SW87 SW85 SW83 SW81 SW79 SW77 SW75 SW73 SW71 SW69
2NA-V646940
C B A# A G# G F# F E D# D C# C B A# A G# G F#F
7 6 6 6 6 6 6 6 6 6 6 6 6 5 5 5 5 5 5 5
CN2
XZ139
J
D99
D98
D97
D96
D94
D93
D91
D92
D90
D89
D87
D88
D86
D85
D84
D82
D81
D79
D80
D78
D77
D75
D76
D74
D73
D72
D107
D108
D106
D105
D103
D104
D102
D101
D100
D95
D83
GHD_EBUS H Circuit Board
A’
A B
to GHDPC-CN1
SW68 SW66 SW64 SW62 SW60 SW58 SW56 SW54 SW52 SW50 SW48 SW46 SW44 SW42 SW40 SW38 SW36 SW34 SW32 SW30 SW2
SW67 SW65 SW63 SW61 SW59 SW57 SW55 SW53 SW51 SW49 SW47 SW45 SW43 SW41 SW39 SW37 SW35 SW33 SW31 SW29 SW2
E D# D C#
B C A# A G# G F# F DE D# C# C B A# A G#
5 5 5 5 5 4 4 4 4 4 4 4 4 4 4 4 4 3 3 3 3
(The first lot only)
(第 1 ロットのみ)
D72
D70
D68
D66
D64
D63
D61
D62
D60
D58
D56
D54
D52
D50
D49
D48
D46
D44
D42
D40
D38
D30
D28
D26
D34
D32
D71
D69
D67
D65
D59
D57
D55
D53
D51
D47
D45
D43
D41
D39
D37
D36
D31
D29
D27
D25
D23
D35
D33
A’ B’
W38 SW36 SW34 SW32 SW30 SW28 SW26 SW24 SW22 SW20 SW18 SW16 SW14 SW12 SW10 SW8 SW6 SW4 SW2
W37 SW35 SW33 SW31 SW29 SW27 SW25 SW23 SW21 SW19 SW17 SW15 SW13 SW11 SW9 SW7 SW5 SW3 SW1
C# C B A# A G# G F# F E D# D C# C B A# A G# G
4 4 3 3 3 3 3 3 3 3 3 3 3 3 2 2 22 2
CN1
to GHD-EBUS L-CN3
CN3
to GHD-EBUS L-CN2
B
D8
D6
D2
D30
D28
D26
D24
D22
D20
D18
D16
D14
D12
D10
D4
注:シートの部品詳細はパーツリストをご参照ください。
D34
D32
D9
D7
D5
D3
D1
D31
D29
D27
D25
D23
D21
D19
D17
D15
D13
D11
D35
D33
Component Side(部品側)
B’
Note: See parts list for details of circuit board component parts.
S90ES
43
S90ES
to HEDaf_M-CN2
F'
F
to HEDaf_M-CN4
F'
F
Component Side(部品側)
NOTE: As for the circuit boards for the keyboard, the circuit board type is
different depending on the lot as follows.
The 1st lot only : 2 pieces (GHD_EBUS H, GHD_EBUS L)
The 2nd lot or later: 3 pieces (HEDaf_H, HEDaf_M, GHD_EBUS L)
注: 鍵盤用基板は、ロットにより、下記の通り基板タイプが違い
ます。部品交換時には注意が必要です。
1 ロットのみ:基板2枚使用 (GHD_EBUS H, GHD_EBUS L)
2 ロット以降:基板3枚使用 (HEDaf_H, HEDaf_M, GHD_EBUS L)
to GHDPC-CN1
Note: See parts list for details of circuit board component parts. 2NAK8-V852150
注:シートの部品詳細はパーツリストをご参照ください。
44
S90ES
H'
H
H'
H
Component Side(部品側)
2NAK8-V852140 Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
45
S90ES
A’
A
to MKSUB-CN1
to MKSUB-CN3
to GHD-EBUS H-CN3
(The 1st lot only)
HEDaf_M-CN3
(The 2nd lot or later)
A’
A
to GHD-EBUS H-CN1
(The 1st lot only)
HEDaf_M-CN1
(The 2nd lot or later)
to PNA-PN-CN1
DM-CN8
Component Side(部品側)
2NAK8-V646930
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
46
S90ES
■ TEST PROGRAM
Test Item List
No. Item Measuring Requirements etc. Test Code
T01 LCD, LED Visual check, LCD all dots ON/OFF(Blink), LED ALL ON/OFF A00200
T02 Panel Switch, LED OK/NG with TONE (1kHz) A00400
T03 Encoder OK 0 - +8 - -8 A00500
T04 Slider OK 0 -127- 64 A00700
T05 1KeyOn OK KeyCode=C3 A00800
T06 Keyboard OK with TONE (1kHz) A00900
After Touch 127-0, offset
T07 Pitch Bend OK 64-127-0 A00A00
Modulation Wheel 0-127
Breath Controller 127-0
T08 Foot Controller OK 0-127 A00B00
Foot Switch 0-1
T09 MIDI IN/OUT/THRU OK/NG Check for THRU (Ohter than MIDI mode)
T10 USB Host OK/NG Device Recognition Test (USB Memory) A00C00
T11 USB MIDI In/Out OK/NG A00D00
T12 1kHz OUTPUT-L sounding Measurement OUTPUT(L)=+5.5±2dBu, (R)=-83.0dBu or less (10kΩ) A00E00
AS-OUT(L)=+5.5±2dBu, (R)=-83.0dBu or less (10kΩ)
PHONES(L)=+6.0±2dBu, (R)=-60.0dBu or less (33Ω)
T13 1kHz OUTPUT-R sounding Measurement OUTPUT(R)=+5.5±2dBu, (L)=-83.0dBu or less (10kΩ) A00F00
AS-OUT(R)=+5.5±2dBu, (L)=-83.0dBu or less (10kΩ)
PHONES(R)=+6.0±2dBu, (L)=-63.0dBu or less (33Ω)
T14 AD -> DA (MIC) Measurement OUTPUT(L)=+4.0±2dBu, (R)=-60.0dBu (10kΩ) A01000
Lch INPUT SW
T15 AD -> DA (LINE) Measurement OUTPUT(R)=+4.0±2dBu, (L)=-70.0dBu (10kΩ) A01100
Rch INPUT SW
T16 PLG1 OK/NG Measurement A01400
T17 PLG2 OK/NG Measurement A01500
T18 PLG3 OK/NG Measurement A01600
T19 SYSTEM ROM OK/NG ID Read A01B00
Wave ROM
T20 SYSTEM RAM OK/NG R/W A01C00
Effect RAM
T21 mLAN I/F check A01D00
T22 Factory Set OK/NG A01E00
T23 Exit(Noise Level) Measurement OUTPUT(L,R)=-90.0dBu (10kΩ) A01F00
AS-OUT(L,R)=-90.0dbu (10kΩ)
PHONES(L,R)=-90.0dBu (33Ω)
Measuring Requirements
To check the product, the following instruments and jigs Jigs: MIDI cable, USB cable (A type - B type)
are required. USB memory, Keyboard amplifier, PLG100-VH
Breath controller(BC3)
Instruments: Foot controller
Frequency counter, Oscilloscope, Level meter FC7 (for FOOT CONTROLLER check)
(JIS-C curve), Distortion meter (Flat), Oscillator FC4 (for FOOT SW(ASSIGNABLE) check)
etc. FC3 (for FOOT PEDAL(SUSTAIN) check)
Short-circuit Connector (for mLAN connection check)
(Refer to Fig.1 on P.65 for Short-circuit connector.)
47
S90ES
MIDI MODE:
MODE PROGRAM
USER 1 USER 2 Turn on the power of main unit, wait for a few seconds, and
SLOT 1 SLOT 2 SLOT 3
A
KEYBOARD
B
ORGAN
C
GUITAR/
PLUCKED
D
BASS
E
STRINGS
F
BRASS
G
REED/PIPE
H
After that, send the data "F0 43 10 18 5A 00 F7", and the
SEQ PLAY
EFFECT
EXIT ENTER REMOTE BYPASS ARPEGGIO 9 10 11 12 13 14 15 16 MUTE
EXECUTE SOLO
[INC/YES]
[CATEGORY SEARCH]
[ENTER]
[DEC/NO] [MUTE]
[EXIT]
PAN/SEND
MODE PROGRAM
PAN REVERB CHORUS TEMPO
This screen appears and the system returns to the wait state
USER 1 USER 2
EQ LOW LOW MID HIGH MID HIGH FAVORITES A. PIANO KEYBOARD ORGAN GUITAR/ BASS STRINGS BRASS REED/PIPE
PLUCKED
MULTI/
VOLUME 1 VOLUME 2 VOLUME 3 VOLUME 4 SEQ PLAY FILE UTILITY A B C D E F G H
EXECUTE SOLO
In this state, press [EXIT]. the system exits the test mode
A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B5 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7
MANUAL MODE:
Press [EXIT]. It becomes the waiting state for test number.
However, this method does not support the [EXIT] button
When the [ENTER] button is pressed, the test program screen
test of "T02 Panel Switch, LED".
is displayed on the LCD.
48
S90ES
F. A/D Value
All the A/D values displayed are the values that are simply
[Description]
shifted the scanned A/D values down to 7 bits.
Black and white of the LCD are displayed inverted about
Also, the software filter is the one before effect.
every 0.5sec., and all LED's are flashed.
LCD: All the dots of LCD are blinked repeatedly via
G. Failure Diagnosis
LCDC.
Conditions
LED: All the LEDs are blinked repeatedly via EBUS
* It is assumed that all power supplies from the power
controller (SWP50 master side).
supply unit are normal.
Confirm that the LCD backlight lights.
* It is assumed that there is no lack for component parts.
Confirm that the contrast can be adjusted to the perfect level
* This is for reference only because there are various
when the contrast VR is moved.
situations.
[Check Item]
<The unit does not operate when turning power on>
Confirm the reversing display of the LCD, and flashing of
* Checkpoints on the power supply unit
the LED's.
* Checkpoints at CPU and the peripheral circuitry
Confirm that backlight of the LCD is on continuously.
1. Is there +3.3V at the plus terminal of C52 (IC2 (DC-DC
Confirm that the contrast can be adjusted by turning the
converter) on DM circuit board) correctly ?
contrast VR.
2. Is there +1.8V at the plus terminal of C171 (IC34 (Power
IC) on DM circuit board) correctly ?
[Display of Test Conclusion]
3. DM Circuit Board: Does the reset signal (at pin no. 220
None
of IC27) return to the level from 0 to +3.3V correctly ?
4. DM Circuit Board: Does the clock signal at pin no.179
[MIDI Code Output for Test Conclusion]
and 180 oscillate correctly ?
None
5. Does not only the LCD display work though other system
works ? (If the panel LEDs light after a while in some
[Ending Process]
places, the system will be normal.)
MANUAL MODE:
6. Observe the waveform of bus signal at ICs 37 and 38
Press the [EXIT] button to exit the test.
(Flash ROMs on DM circuit board).
The initial screen reappears and the system returns to the
Is the waveform stable with a constant cycle ?
wait state for test number.
Check each waveform of the data and address buses
because there may be a pattern bridge on the buses which
MIDI MODE:
causes the program loop.
By sending other test code newly, the current test is finished,
7. When only the IC37 (Flash ROM (erea4) on DM circuit
and new test can be executed.
board) is defective, it may stop at the opening screen.
49
S90ES
Press [EXIT]. The test is finished, the initial screen is Confirm that LEDs operate correctly and there is no
displayed, and it becomes the wait state for test number. irregularity in brightness.
[Others] [Procedure]
None Turn on and off all switches by following the instruction below.
[Failure Diagnosis]
Defect of T01
<LED doesn't light>
1. Is there +5V (power supply input voltage) at pin 6 of
CN1 on PNA circuit board ?
2. Are all the signals at CN8 on DM circuit board all right ?
Also, are all the signals interfaced with PNA circuit When the appropriate switch is pressed, the sine wave
board correctly ? sounds while the switch is on, and the test proceeds to the
While moving slider VR and so on with "pin 1 of CN8 = next switch.
(H)", observe the signal at pins 3 and 5 on CN8. If an unfit switch is pressed, 'NG' is indicated on the LCD
3. PNA circuit board: Are there the signals at pins 1 to 8, and no sound is produced. Then, if the appropriate switch is
11, 12, 15 and 43 to 50 on IC2 correctly ? pressed anew, the test proceeds to the next switch.
4. Is the LED drive circuit (TA1 and TA2 on PNA circuit When all switches work normally, 'OK' is indicated on the
board) all right ? LCD.
<LCD doesn't work at all> The following table shows the switch test sequence.
1. DM Circuit Board: Are both +5V (plus terminal of C47) The LED color is shown in the back of comma.
and -12V ( minus terminal of C1) supplied to CN10 (O = Orange, G = Green, R = Red)
correctly ? As for the switch with "two color LED", press the switch
2. DM Circuit Board: Are all the signals at CN10 and CN14 twice.
all right ?
3. DM Circuit Board: Are all the signals at pin 19 of IC27, [PAN (KF1),O] -> [TONE (KF2),O] ->
pin 12 of IC11 and pin 6 of IC14 and the reset signals all [ARPFX (KF3),O] -> [EQ (KF4),O] ->
right ? [VOL (KF5),G] ->
4. R22 relates to the backlight lighting at CN3 on the PNA
circuit board. (The power supply is +5V. ) [SF1,-] -> [SF2,-] -> [SF3,-] ->
5. Defect on LCD unit side (Exchange for another unit.) [SF4,-] -> [SF5,-] -> [INFO,-] ->
6. Is the contrast VR circuit all right ? [F1,-] -> [F2,-] -> [F3,-] ->
[F4,-] -> [F5,-] -> [F6,-] ->
T02: Panel Switch, LED Check
(TEST CODE: A00400) [DEC,-] -> [INC,-] -> [ C LEFT,-] ->
[Initial Screen] [ C-UP,-] -> [ C RGHT,-] -> [EXIT,-] ->
[ C DOWN,-] -> [ENTER,-] ->
50
S90ES
[PLG2,G] -> [PLG3,G] -> [PLG3,G] -> While moving slider VR and so on with "pin 1 of CN8 =
(SLOT2) (SLOT3) (H)", observe the signal at pins 3 and 5 on CN8.
[CATEGORY,O] -> 3. Is there a solder bridge and so on at the pins of IC2 on
[A,G] -> [B,G] -> [C,G] -> PNA circuit board ?
[D,G] -> [E,G] -> [F,G] -> 4. Are there the signals at pins 1 to 8, 11, 12, 15 and 55 to
[G,G] -> [H,G] -> 62 on IC2 correctly ?
[1,O] -> [2,O] -> [3,O] -> 5. When pressing the switch, if no sound is output, refer to
[4,O] -> [5,O] -> [6,O] -> "T12: Failure Diagnosis" section.
[7,O] -> [8,O] -> [TR.SEL,O] ->
[9,O] -> [10,O] -> [11,O] -> T03: Encoder Check
[12,O] -> [13,O] -> [14,O] ->
(TEST CODE: A00500)
[15,O] -> [16,O] -> [MUTE,R]
[Initial Screen]
[Check Item]
Confirm that the all switches work normally.
Confirm that the all LEDs work normally.
[Procedure]
NG
By following the instruction below, turn the encoder
clockwise and then turn it counterclockwise. According to
the display of “<+8> +0”, turn the encoder knob clockwise
from +0 to +7. When the display of “<-8> +0” appears, turn
the encoder knob counterclockwise from -0 to -7.
[MIDI Code Output for Test Conclusion]
OK A0 04 02 <== (When all the panel switches are normal)
NG No output
[Ending Process]
When all switches work normally, 'OK' is indicated on the
LCD and the system exits the test and returns to the wait
state for test number. [Check Item]
For NG determined on the way of the test, see "D. Test Turn the encoder clockwise and confirm that the number
Procedure for NG". indicated on the LCD increases smoothly form +1 to +7.
Then turn the encoder counterclockwise and confirm that the
[Others] number decreases smoothly from -1 to -7 and that 'OK' is
None indicated on the LCD.
51
S90ES
[Ending Process]
After the result is indicated on the LCD, the system exits the
test and returns to the wait state for test number. [Check Item]
For NG determined on the way of the test, see "D. Test Confirm that the value changes smoothly and that 'OK' is
Procedure for NG". indicated.
[Failure Diagnosis]
Defect of T03
<Encoder doesn't react>
1. Is there +5V (power supply input voltage) at pin 6 of
CN1 on PNA circuit board ? NG No Display
2. Are all the signals at CN8 on DM circuit board all right ?
Also, are all the signals interfaced with PNA circuit [MIDI Code Output for Test Conclusion]
board correctly ? OK A0 07 02 <==
While moving slider VR and so on with "pin 1 of CN8 = NG No output
(H)", observe the signal at pins 3 and 5 on CN8.
3. Is there a solder bridge and so on at the pins of IC2 on [Ending Process]
PNA circuit board ? After the result is indicated on the LCD, the system exits the
4. Is there a solder bridge etc. on the signal lines from pin test and returns to the wait state for test number.
20 of IC4 on PNA circuit board ? For NG determined on the way of the test, see "D. Test
5. Is the encoder itself defective ? Procedure for NG".
52
S90ES
T05: 1KeyOn Check (While moving slider VR and so on with "pin 1 of CN8 =
(TEST CODE: A00800) (H)", observe the signal at pins 3 and 5 on CN8.)
[Initial Screen] 2. Is the keyboard unit itself all right ?
[Description]
Checks the keyboards work normally.
It compares Key On information (from the EBUS
controller) with <C3>KeyON.
[Procedure] [Description]
Press the C3 key. Checks keyboards work normally.
It compares Key On information (from the EBUS
controller) with Key Number on the LCD display.
It displays Velocity in the received information, only when
key is on.
Checks After Touch works normally.
[Check Item] It compares Keyboard After Touch information (from the
Confirm the result indicated on the LCD. EBUS controller) with the target value on the LCD display.
NG No Display
[Ending Process]
When the C3 key works normally, 'OK' is indicated on the
LCD and the system exits the test and returns to the wait
state for test number.
For NG determined on the way of the test, see "D. Test
Procedure for NG". After Touch Check
53
S90ES
[Ending Process]
When all keys work normally, 'OK' is indicated on the LCD
and the system exits the test and returns to the wait state for Each control can be checked in any order.
test number.
For NG determined on the way of the test, see "D. Test [Check Item]
Procedure for NG". Confirm that the value changes continuously and 'OK' is
indicated on the LCD.
[Others]
None [Display of Test Conclusion]
OK
[Failure Diagnosis]
Defect of T06
<Keyboard+AT doesn't react>
1. Are all the signals at CN8 on DM circuit board all right ?
Also, are all the signals interfaced with PNA circuit
board correctly ? NG No Display
While moving slider VR and so on with "pin 1 of CN8 =
(H)", observe the signal at pins 3 and 5 on CN8. [MIDI Code Output for Test Conclusion]
2. Is the keyboard unit itself all right ? OK A0 0A 02 <==
NG No output
T07: PB, MW, BC Check
(TEST CODE: A00A00) [Ending Process]
[Initial Screen] After the result is indicated on the LCD, the system exits the
test and returns to the wait state for test number.
For NG determined on the way of the test, see "D. Test
Procedure for NG".
54
S90ES
[Others]
None
[Failure Diagnosis]
Defect of T07
<PB/MW doesn't react>
1. Are all the signals at CN9 on DM circuit board all right ? Each controller can be checked in any order.
Also, are all the signals interfaced with PB/MW correctly ?
2. Is +2.5V (Standard Voltage) output from pin 1 of IC15 on [Check Item]
DM circuit board ? Confirm that the value changes and 'OK' is indicated on the
3. Is the operating voltage supplied to pins 238 and 239 of LCD.
IC27 on DM circuit board ?
[Display of Test Conclusion]
<BC doesn't react> OK
1. Are all the signals at JK5 on DM circuit board all right ?
2. Is the operating voltage supplied to pin 236 of IC27 on
DM circuit board ?
3. Is -12V output at pin 2 of JK5 on DM circuit board ?
[Ending Process]
After the result is indicated on the LCD, the system exits the
test and returns to the wait state for test number.
[Description] For NG determined on the way of the test, see "D. Test
Checks that the foot controller 1/2, the sustain sw and the Procedure for NG".
foot sw work normally.
The values of Foot Controller 1/2 are input from the A/D In [Others]
of CPU. None
It compares the value with the target value on the LCD
display. [Failure Diagnosis]
The values of Sustain and Switch ON/OFF are input from Defect of T08
the input port of CPU. <FC1 doesn't react>
It compares the value with the target value on the LCD 1. Are all the signals at JK4 on DM circuit board all right ?
display. 2. Is the operating voltage supplied to pin 235 of IC27 on
DM circuit board ?
[Procedure]
As for FC1/FC2 test, use a foot controller (FC7). <FC2 doesn't react>
As for Sustain SW test, use a damper pedal (FC3). 1. Are all the signals at JK3 on DM circuit board all right ?
As for Foot SW test, use a foot switch (FC4). 2. Is the operating voltage supplied to pin 234 of IC27 on
By following the instruction below, operate each controller; DM circuit board ?
Foot Controller 1/2 : Move continuously from 0(0-2) to
127(125-127) (release and depress). <Sustain switch doesn't react>
(Sustain Switch : 35 or less - 101 or more) 1. Are all the signals at JK3 on DM circuit board all right ?
Foot Switch : Turn on (0) and off (1) 2. Is the operating voltage supplied to pin 233 of IC27 on
DM circuit board ?
55
S90ES
[Others]
In the MIDI mode, check it by the following procedure.
It is not necessary to check MIDI IN and MIDI OUT
[Description]
because the test by MIDI is possible.
Checks the operation of MIDI IN/OUT/THRU with the test
As for the test of THRU, not in the test mode, send MIDI
pattern (AA EF 00 55).
code "AA EF 00 55" to MIDI IN of the main unit. Then,
It transmits a specific data group from the serial
confirm that the same MIDI code is output from THRU.
transmission of CPU. Then, it confirms that the same data
group is received within a specified time.
[Failure Diagnosis]
By the way, this test can be executed by the manual mode
Defect of T09
only. Refer to the following [Others] for MIDI MODE.
<MIDI doesn't react>
1. Are all the signals at JK5 on DM circuit board all right ?
[Procedure]
2. Connect MIDI IN and OUT terninal using a MIDI cable
Connect 'MIDI IN' and 'MIDI OUT' via a MIDI cable and
to make a loop circuit.
execute the test.
At that time, the test signal is output from pin 195 of
IC27 on DM circuit board.
[Check Item]
Does the same signal come back to pin 201 of IC27 via
Confirm that the 'OK' is indicated at IN, OUT check.
pin 8 of IC10 and pin 10 of IC14 ?
Confirm that the MIDI monitor outputs the test pattern
(AA EF 00 55) from THRU.
T10: USB (HOST) Check
(TEST CODE: A00C00)
[Display of Test Conclusion]
[Initial Screen]
OK
[Description]
Checks that USB(HOST) operates normally.
NG (Example) Executes the recognition test of the connected equipment.
Confirms the presence of USB memory via CPU built in
USB host controller.
[Procedure]
When an unexpected data is received. Press [ENTER] with the initial screen. After the following
display appears, connect a USB memory to USB (To
DEVICE) terminal, and press [ENTER] to execute the test.
56
S90ES
[Check Item]
Confirm the USB memory is recognized.
NG [Procedure]
Press [ENTER] with the initial screen.
After the following display appears, connect USB (To DEVICE)
and USB (To HOST) terminals, and press [ENTER] to execute
the test.
[Failure Diagnosis]
Defect of T10
<USB(HOST) doesn't react>
NG
1. Are all the signals at CN12 on DM circuit board all right ?
2. Is the data input/output executed at pins 229 and 230 of
IC27 on DM circuit board correctly ?
3. As for the data at pins 224 and 227 of IC27 on DM
circuit board, is the data no problem ?
4. Is +5V output from pins 6 and 8 of IC32 on DM circuit [MIDI Code Output for Test Conclusion]
board ? OK A0 0D 02 <==
5. Is the clock signal supplied from oscillator X4 to pin 219 NG A0 0D 03 <==
of IC27 on DM circuit board ?
6. Did you insert a USB memory into the USB terminal [Ending Process]
before executing the test ? (If so, you should insert it After the result is indicated on the LCD, the system exits the
later.) test and returns to the wait state for test number.
[Others]
None
57
S90ES
MIDI MODE:
[Description] By sending other test code newly, the current test is finished,
It checks that OUTPUT-L, Assignable OUTPUT-L and and new test can be executed.
PHONES-L jacks output normal signal. Press [EXIT]. The test is finished, the initial screen appears,
Move VOLUME controller and confirm the volume of and the system returns to the wait state for test number.
OUTPUT L varies smoothly.
It sounds the sine wave of Wave ROM from SWP50 (Master [Others]
side). Then, it outputs the sound to the specified output. None
It sets Volume Data to DAC, and adjusts the volume.
[Failure Diagnosis]
[Procedure] Defect of T12
Connect a plug into OUTPUT-L, OUTPUT-R, Assignable-L, <No sound (1kHz) from OUTPUT L>
Assignable-R, PHONES(L) and PHONES(R) jacks to 1. Are all the digital signals at pins of ICs 5 and 6 on DM
monitor the frequency, the wave form, the output level of circuit board all right ?
each signal by using a frequency counter, an oscilloscope, 2. Is the sine wave output from pins 22 and 23 of IC5 and
and a level meter (JIS-C filter). Set the master volume to pins 22 and 23 of IC6 on DM circuit board ?
MAX. While the signal is output, the following screen 3. Is it all right for the signal line from CN3 on DM circuit
appears on the LCD. board to pin 1 of CN101 on PNA-AN circuit board ?
4. Is it all right for the output signal at pin 7 of IC102, pin
7 of IC103 and pin 1 of IC101 on PNA-AN circuit board ?
5. Is it all right for the output signal at TR101, TR105, pin
7 of IC103 and pin 1 of IC101 on PNA-AN circuit board ?
58
S90ES
[Check Item]
OUTPUT-L: -83.0dBm or less (loading 10kΩ)
OUTPUT-R: 1kHz±1.5Hz, sine wave, +5.5±2dBu
(loading 10kΩ, distortion factor 0.1% or less)
Move VOLUME controller and confirm the
volume of OUTPUT L varies smoothly. [Description]
Assignable-L: -83.0dBm or less (loading 10kΩ) It checks the signal path from A/D input to D/A output. (The
Assignable-R: 1kHz±1.5Hz, sine wave, +5.5±2dBu Gain is set to MIC as a default.)
(loading 10kΩ, distortion factor 0.1% or less) It outputs the input from ADC to DAC via SWP50 (Master
PHONES(L): -63.0dBu or less (loading 33Ω) side). It sets AD Gain to MIC via CPU.
PHONES(R): 1kHz±1.5Hz, sine wave, +6.0±2dBu
(loading 33Ω, distortion factor 0.1% or less) [Procedure]
Apply the sine wave of 1kHz±5Hz, -52dBu (distortion factor
[Display of Test Conclusion] 0.1% or less) into th A/D input L, and execute the test.
OK No Display Then, confirm that the following output level is gained at
NG No Display OUTPUT L and R.
[Ending Process]
MANUAL MODE:
Press the [EXIT] button to exit the test.
The initial screen appears on the LCD and the system
returns to the wait state for test number. [Check Item]
Rotate the A/D GAIN VOLUME knob and confirm that the
MIDI MODE: sound volume changes.
By sending other test code newly, the current test is finished,
59
S90ES
Connect and disconnect the plug and confirm that the [Description]
appropriate switch status is indicated on the LCD. It checks the signal path from A/D input to D/A output.
(The Gain is set to LINE as a default.)
Confirm that the following output level is gained at It outputs the input from ADC to DAC via SWP50 (Master
OUTPUT L and R. side). It sets AD Gain to LINE via CPU.
OUTPUT-L: 1kHz±5Hz, sine wave, +4.0±2dBu
(loading 10kΩ, distortion factor 0.2% or less) [Procedure]
OUTPUT-R: -60.0dBu or less (loading 10kΩ)
Apply the sine wave of 1kHz±5Hz, -27.0dBu±0dBu
(distortion factor 0.1% or less) into the A/D input R, and
[Display of Test Conclusion]
execute the test.
No Display
Then, confirm that the following output level is gained at
OUTPUT L and R.
[MIDI Code Output for Test Conclusion]
No output
[Ending Process]
MANUAL MODE:
Press the [EXIT] button to stop the sound. The system
returns to the wait state for test number.
[Check Item]
MIDI MODE:
Rotate the A/D GAIN VOLUME knob and confirm that the
By sending other test code newly, the current test is finished,
sound volume changes.
and new test can be executed.
Connect and disconnect the plug and confirm that the
Press [EXIT]. The test is finished, the initial screen appears,
appropriate switch status is indicated on the LCD.
and the system returns to the wait state for test number.
Confirmt that the following output level is gained at
OUTPUT L and R.
[Others]
OUTPUT-L: -70.0dBu or less (loading 10kΩ)
None
OUTPUT-R: 1kHz±5Hz, sine wave, +4.0±2dBu
(loading 10kΩ, distortion factor 0.2% or less)
[Failure Diagnosis]
Defect of T14
[Display of Test Conclusion]
<A/D->D/A:MIC sound is not output>
No display
1. Are all the digital signals at pins of IC4 on DM circuit
board all right ?
[MIDI Code Output for Test Conclusion]
2. Is the sine wave input at pin 2 of IC4 on DM circuit board ?
No output
3. Is it all right for the signal lines from CN3 on DM circuit
board to CN101 on PNA-AN circuit board ?
[Ending Process]
4. Is it all right for the output signal at pin 1 of IC104 and
MANUAL MODE:
pin 7 of IC105 on PNA-AN circuit board ?
Press the [EXIT] button to stop the sound. The system
5. Is VR100 on PNA-AM circuit board set to minimum ?
returns to the wait state for test number.
6. Are TR102 and TR103 set to ON when the level is low ?
7. If AD/DA(MIC) is not ON, does the level at pin 28 of
MIDI MODE:
CN101 vary, when a plug is inserted ?
By sending other test code newly, the current test is finished,
and new test can be executed.
T15: A/D -> D/A (LINE) Check
Press [EXIT]. The test is finished, the initial screen appears,
(TEST CODE: A01100)
and the system returns to the waiting state for test number.
[Initial Screen]
[Others]
None
60
S90ES
[Failure Diagnosis]
Defect of T16
<No sound with PLG1>
1. Are all the digital signals at pins of IC4 on DM circuit
board all right ?
2. Are the signal lines at pins of ICs 7 and 8 on DM circuit
[Check Item]
board all right ?
Confirm that the following output levels are gained at
3. Are the signal lines at pins of IC17 on DM circuit board
OUTPUT L and R.
all right ?
61
S90ES
4. Is +5V (Power supply for Plug-in board from DM circuit Error Code
board) output from + terminal of C48 (or IC3) ? NG_BOARD: A board other than VH is inserted.
NO_BOARD: No board (is inserted.)
T17: Plug-In 2 Check
MIDI: MIDI LINE error
(TEST CODE: A01500)
[Initial Screen]
[MIDI Code Output for Test Conclusion]
NG(MIDI) A0 15 03 <==
NG(NO_BOARD) A0 15 04 <==
NG(NG_BOARD) A0 15 05 <==
OK No output
[Description]
[Ending Process]
It checks connection at the Plug-in Slot 2, transmission/
MANUAL MODE:
reception through the Control Line, the MIDI LINE, and IN/
Press the [EXIT] button once to stop the sound, twice to
OUT through the MEL Line.
confirm the test result (OK or NG), and three times to have
Actually, if it is all right after executing Inspection Chck, it
the system return to the wait state for test number.
executes Board Type Request, and receives Type, and judges
whether it is VH board or not.
MIDI MODE:
After the judgement, it transmits Test Code to MIDI line of
By sending other test code newly, it stops sounding,
Plug-in, and outputs the sine wave (1kHz) to Plug-in in
transmits the test result and executes new test.
order to check IN/OUT of MEL line.
Press [EXIT]. It displays the next screen, transmits the test
It sounds the sine wave of Wave ROM from SWP50 (Master
result and stops sounding.
side). Then, it outputs the signal to DAC via Plug In Board
Press [EXIT] again to return to the wait state for test code.
(VH) and SWP50 (Master side).
[Others]
[Procedure]
None
Connect a Vocal Harmony Plug-in Board into the Plug-in
Slot 2, and confirm that the following output levels are
[Failure Diagnosis]
gained at OUTPUT L and R.
Defect of T17
Set the master volume to maximum in advance.
<No sound with PLG2>
1. Are all the digital signals at pins of IC5 on DM circuit
board all right ?
2. Are the signal lines at pins of ICs 7 and 8 on DM circuit
board all right ?
[Check Item] 3. Are the signal lines at pins of IC17 on DM circuit board
Confirm that the following output levels are gained at all right ?
OUTPUT L and R. 4. Is +5V (Power supply for Plug-in board from DM circuit
OUTPUT L:1kHz±5Hz, sine wave, +6.0±2dBu board) output from + terminal of C48 (or IC3) ?
(loading 10kΩ, distortion factor 2.00% or less)
OUTPUT R:1kHz±5Hz, sine wave, +6.0±2dBu T18: Plug-In 3 Check
(loading 10kΩ, distortion factor 2.00% or less) (TEST CODE: A01600)
[Initial Screen]
[Display of Test Conclusion]
OK No Display
NG
[Description]
It checks connection at the Plug-in Slot 3, transmission/
reception through the Control Line, the MIDI LINE, and IN/
OUT through the MEL Line.
62
S90ES
Actually, if it is all right after executing Inspection Chck, it confirm the test result (OK or NG), and three times to have
executes Board Type Request, and receives Type, and judges the system return to the wait state for test number.
whether it is VH board or not.
After the judgement, it transmits Test Code to MIDI line of MIDI MODE:
Plug-in, and outputs the sine wave (1kHz) to Plug-in in By sending other test code newly, it stops sounding,
order to check IN/OUT of MEL line. transmits the test result and executes new test.
It sounds the sine wave of Wave ROM from SWP50 (Master Press [EXIT]. It displays the next screen, transmits the test
side). Then, it outputs the signal to DAC via Plug In Board result and stops sounding.
(VH) and SWP50 (Master side). Press [EXIT] again to return to the wait state for test code.
[Procedure] [Others]
Connect a Vocal Harmony Plug-in Board into the Plug-in None
Slot 3, and confirm that the following output levels are
gained at OUTPUT L and R. [Failure Diagnosis]
Set the master volume to maximum in advance. Defect of T18
<No sound with PLG3>
1. Are all the digital signals at pins of IC6 on DM circuit
board all right ?
2. Are the signal lines at pins of ICs 7 and 8 on DM circuit
board all right ?
[Check Item] 3. Are the signal lines at pins of IC17 on DM circuit board
Confirm that the following output levels are gained at all right ?
OUTPUT L and R. 4. Is +5V (Power supply for Plug-in board from DM circuit
OUTPUT-L: 1kHz±5Hz, sine wave, +6.0±2dBu board) output from + terminal of C48 (or IC3) ?
(loading 10kΩ, distortion factor 2.00% or less)
OUTPUT-R: 1kHz±5Hz, sine wave, +6.0±2dBu T19: ROM Check
(loading 10kΩ, distortion factor 2.00% or less) (TEST CODE: A01B00)
[Initial Screen]
[Display of Test Conclusion]
OK No Display
NG
[Description]
Checks the ID Read on the MAIN CPU FLASH ROM.
(IC38,IC37)
Error Code It acquires Device ID from each ROM, and compares it with
NG_BOARD: A board other than VH is inserted. the specified ID.
NO_BOARD: No board (is inserted.) Compares each Wave ROM data at the following address
MIDI: MIDI LINE error point. IC44(H1), IC45(H2), IC42(L1), IC43(L2)
As for each ROM, it reads data from the specific address
[MIDI Code Output for Test Conclusion] group, and compares it with the specified value.
NG(MIDI) A0 16 03 <==
NG(NO_BOARD) A0 16 04 <== [Procedure]
NG(NG_BOARD) A0 16 05 <== Execute the test.
OK No output
[Check Item]
[Ending Process] Confirm the result indicated on the LCD.
MANUAL MODE:
Press the [EXIT] button once to stop the sound, twice to
63
S90ES
NG (Example)
[Description]
It checks Write/Read/Verify operation on the MAIN CPU
and Effect SDRAMs.
IC33(H), IC29 (for Effect, Master side), IC35 (for Effect,
Slave side)
If either of the target IC's is NG, the test results in NG. It writes the specific data to the specific address group, and
read the data, and compares it with the written value.
[MIDI Code Output for Test Conclusion]
OK A0 1B 02 <== [Procedure]
NG) A0 1B 03 <== Execute the test.
[Failure Diagnosis]
Defect of T19
<System ROM (IC38, IC37) Test is NG>
1. According to the test result of the defective IC number,
check the IC on DM circuit board. NG (Example)
However, check both bus lines of ICs 37 and 38 in order
to find a solder bridge etc. because the buses are common
to both ICs 37 and 38.
2. If IC38 on DM circuit board is NG, it often occurs that
the system does not boot up at all.
3. When IC37 on DM circuit board is NG, it may stop at the If either of the target IC's is NG, the test results in NG.
opening screen "S90ES"
[MIDI Code Output for Test Conclusion]
<Wave ROM (IC44, IC45,IC42,IC43) Test is NG> OK A0 1C 02 <==
1. Are all the digital signals at pins of ICs 25 and 30 on DM NG) A0 1C 03 <==
circuit board all right ?
2. According to the test result of the defective IC number, [Ending Process]
check the IC on DM circuit board. After the result is indicated on the LCD, the system exits the
However, check both bus lines of ICs 42 and 43 (or ICs test and returns to the wait state for test number.
44 and 45) in order to find a solder bridge etc. because
the buses are common to both ICs 42 and 43 (or both ICs [Others]
44 and 45). The data of all RAMs is saved.
3. Is +1.5V (power supply for ICs 25 and 30 on DM circuit In a word, it saves data once soon before the verify check,
board) all right ? (+ terminal of C266) returns it soon after the verify check, and repeats it.
64
S90ES
48 48
(TEST CODE: A01D00) 49 49
50 50
[Initial Screen]
b a
65
S90ES
66
S90ES
[Check Item]
None
Others:
[Others]
After exiting the test mode, normal boot sequence runs.
Factory Set (in detail)
67
S90ES
Shipment Settings
When shipping it, the controllers on the main unit are set as
follows.
68
S90ES
■ テストプログラム
テスト項目一覧
番号 項目 測定条件など テストコード
T01 LCD, LED 目視 白黒反転ブリンク、LED ALL ON/OFF A00200
T02 Panel Switch, LED OK/NG with TONE (1kHz) A00400
T03 Encoder OK 0 - +8 - -8 A00500
T04 Slider OK 0-127-64 A00700
T05 1KeyOn OK KeyCode=C3 A00800
T06 Keyboard OK with TONE(1kHz) A00900
After Touch 127-0, offset
T07 Pitch Bend OK 64-127-0 A00A00
Modulation Wheel 0-127
Breath Controller 127-0
T08 Foot Controller OK 0-127 A00B00
Foot Switch 0-1
T9 MIDI IN/OUT/THRU OK/NG THRU の確認 (MIDI Mode 以外)
T10 USB Host OK/NG Device 認識試験 (USB Memory) A00C00
T11 USB IN/OUT OK/NG A00D00
T12 1kHz OUTPUT-L 発音 測定 OUTPUT(L)=+5.5 ± 2dBu, (R)=-83.0dBu 以下 (10k Ω) A00E00
AS-OUT(L)=+5.5 ± 2dBu, (R)=-83.0dBu 以下 (10k Ω)
PHONES(L)=+6.0 ± 2dBu, (R)=-63.0dBu 以下 (33 Ω)
T13 1kHz OUTPUT-R 発音 測定 OUTPUT(R)=+5.5 ± 2dBu, (L)=-83.0dBu 以下 (10k Ω) A00F00
AS-OUT(R)=+5.5 ± 2dBu, (L)=-83.0dBu 以下 (10k Ω)
PHONES(R)=+6.0 ± 2dBu, (L)=-63.0dBu 以下 (33 Ω)
T14 AD -> DA (MIC) 測定 OUTPUT(L)=+4.0 ± 2dBu, (R)=-60.0dBu 以下 (10k Ω) A01000
Lch INPUT SW
T15 AD -> DA (LINE) 測定 OUTPUT(R)=+4.0 ± 2dBu, (L)=-70.0dBu 以下 (10k Ω) A01100
Rch INPUT SW
T16 PLG1 OK/NG 測定 A01400
T17 PLG2 OK/NG 測定 A01500
T18 PLG3 OK/NG 測定 A01600
T19 SYSTEM ROM OK/NG ID Read A01B00
Wave ROM
T20 SYSTEM RAM OK/NG R/W A01C00
Effect RAM
T21 mLAN I/F チェック A01D00
T22 Factory Set OK A01E00
T23 Exit(Noise Level) 測定 OUTPUT(L,R)=-90.0dBu (10k Ω) A01F00
AS-OUT(L,R)=-90.0dbu (10k Ω)
PHONES(L,R)=-88.0dBu (33 Ω)
69
S90ES
MODE PROGRAM
この画面の状態で [ENTER] ボタンを押すと、
USER 1 USER 2
MIDI MODE:
PLUCKED
MULTI/
SEQ PLAY FILE UTILITY A B C D E F G H
本体の電源立ち上げ後、数秒待ち、プレイ画面
CHOIR PERCUSSION PERCUSSION
TRACK
EDIT JOB STORE 1 2 3 4 5 6 7 8 SELECT
[INC/YES]
[CATEGORY SEARCH]
[ENTER] 面が表示されます。
[DEC/NO] [MUTE]
[EXIT]
PAN/SEND
MODE PROGRAM
PAN REVERB CHORUS TEMPO
EQ LOW LOW MID HIGH MID HIGH FAVORITES A. PIANO KEYBOARD ORGAN GUITAR/ BASS STRINGS BRASS REED/PIPE
PLUCKED
MULTI/
VOLUME 1 VOLUME 2 VOLUME 3 VOLUME 4 SEQ PLAY FILE UTILITY A B C D E F G H
EFFECT
F1 F2 F3 F4 F5 F6 EXIT ENTER REMOTE BYPASS ARPEGGIO 9 10 11 12 13 14 15 16 MUTE
EXECUTE SOLO
A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B5 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7
A. 準備
この画面が表示されたら、MIDI テストコード
このテストプログラムは、本体パネルスイッチで
待ちとなります。
操作する MANUAL MODE と、MIDI 信号によっ
この画面の状態で、[EXIT] を押すと、テストモー
てコントロールされる MIDI MODE があります。
ドを抜け、通常の電源オン状態になります。
それぞれテストエントリー方法、テストの進め方、
テスト項目に違いがあります。ただし、本体 LCD
C. テストの進め方
表示、判定出力コードは共通です。本文中、MIDI
MANUAL MODE:
コード、本体 LCD 表示に関し、次の表現を用います。
テストにエントリーすると、次の画面が表示さ
* 本体から出力される MIDI CODE れます。
MIDI コードの後ろに "<==" を付けます。
* 本体テストを操作する MIDI CODE
MIDI コードの前に "==>" を付けます。
* パネルスイッチ
括弧“[ ]”で囲まれています。
* テストコード
それぞれのテスト固有の数字です。
テストモード目次の表 (P.69) の”テスト [DEC/NO], [INC/YES] ボタンを押してテストナ
コード”を参照して下さい。
* テストナンバー ンバーを選択します。
それぞれのテスト固有の数字であり、テスト [ENTER] ボタンを押すと、現在選択されている
を選択する時のナンバーと同じです。
テストナンバーが実行されます。
* 事前にユーザーデータをバックアップしてお [EXIT] ボタンを押すと、"T23 EXIT" が実行さ
いて下さい。(P.94参照) れます。
70
S90ES
G. 故障診断
故障診断条件
* 電源ユニットからの供給電圧は全て正常とします。 [テスト内容]
* 部品等の欠品は無いものとします。 約 0.5 秒毎に LCD を黒白反転、LED を全点灯
* 色々な状況がありますので参考程度にして下さい。 /消灯します。
LCD: LCDC 経由で全ドット表示、非表
示を繰り返します。
71
S90ES
MIDI MODE:
他のテストのテストコードを送ると、テストは
終了し、新たに送られてきたテストコードのテ [テスト内容]
ストが実行されます。 パネルスイッチが正常に動作することを確認し
[EXIT] を押すと、テストは終了し、
(最初の表示) ます。
と同じ画面を表示して、テストナンバー待ち状 EBUS コントローラからの SW ON 情報と LCD
態になります。 表示の SW No. を比較し、一致した場合は
SWP50 にて正弦波を発音、対応する LED が存
[その他] 在する場合は同時に当該 LED を点灯させます。
なし LED が正常に動作し、光度にムラがないことを
確認します。
[故障診断]
T01 の不良 [テスト方法]
本体のすべてのスイッチを、以下の表示にした
<LED が点灯しない > がって ON/OFF します。
[CATEGORY,O] ->
[A,G] -> [B,G] -> [C,G] ->
[D,G] -> [E,G] -> [F,G] ->
[G,G] -> [H,G] ->
[1,O] -> [2,O] -> [3,O] ->
[4,O] -> [5,O] -> [6,O] ->
正常な場合、ON している間、正弦波が発音し [7,O] -> [8,O] -> [TR.SEL,O] ->
て、次のスイッチのテストに進みます。 [9,O] -> [10,O] -> [11,O] ->
表示と異なるスイッチが押されると、NG が表 [12,O] -> [13,O] -> [14,O] ->
示され発音しません。その後、正しいスイッチ [15,O] -> [16,O] -> [MUTE,O]
が押されると、次のスイッチのテストに進みま
す。すべてのスイッチが正常であれば、OK が [テスト項目]
表示されます。 すべてのスイッチが正常に動作することを確認
します。
スイッチのチェック順序を、下記に示します。 すべての LED が正常に動作することを確認します。
その際の LED 色を "," の後に示します。
(O = Orange, G = Green, R = Red) [判定結果の表示]
(ひとつのスイッチについて 2 色 LED がある場 OK
合には、2 回スイッチを押します。 )
73
S90ES
[故障診断] [テスト項目]
T02 の不良 時計回りに回したとき、画面右側の数字が +0
から +7 までスムーズに増え、次に反時計回り
< SW が反応しない > に回したとき、+0 から -7 までスムーズに減り、
OK の表示が出ることを確認します。
1. PNA シート CN1-6 +5V 電源入力は OK
ですか? [判定結果の表示]
2. DM シート CN8 の信号は全て OK で PNA OK
シートに I/F されていますか?
(CN8-1=(H) でスライダー VR 等を動かし
ながら CN8-3、5 の信号が観測出来ます。)
3. PNA シート IC2 のピンで半田ブリッジ等
はありませんか?
4. PNA シート IC2-1 - 8、11、12、15 ピン、 NG 表示なし
55 - 62 ピンは OK ですか?
5. SW を押した時に音が出ない場合は、T12 [判定結果の MIDI コード出力]
の診断を参照して下さい。 OK A0 05 02 <==
NG 出力なし
T03: Encoder チェック
(テストコード: A00500) [テストの終了方法]
[最初の表示] 判定を表示、出力してテストを終了し、テスト
ナンバー待ち状態となります。
テスト途中で NG と判断した場合の処理方法
は、"D. NG と判断したときのテストの進め方 "
を参照してください。
[その他]
[テスト内容]
なし
Encoder が正常に動作することを確認します。
EBUS コントローラからの Encoder 情報を LCD
[故障診断]
表示の目標値と比較します。
T03 の不良
[テスト方法]
< エンコーダが反応しない >
Encoder を、以下の LCD 表示にしたがって時計
回りに回し、次に反時計回りに動かします。
1. PNA シート CN1-6 +5V 電源入力は OK で
“:<+8> +0”の表示に従って、時計回りに +1、
すか?
+2 ∼ +7 まで回転させます。
2. DM シート CN8 の信号は全て OK で PNA
“:<-8> +0”表示が出た時、半時計回りに -1、
シートに I/F されていますか?
-2 ∼ -7 まで回転させます。
(CN8-1=(H) でスライダー VR 等を動かし
ながら CN8-3、5 の信号が観測出来ます。)
3. PNA シート IC2 のピンで半田ブリッジ等
はありませんか?
4. PNA シート IC4-20 から信号ラインで半田
目標値 ブリッジ等がありませんか?
現在値
5. エンコーダ部品不良?
74
S90ES
[その他]
[テスト内容]
なし
Slider が正常に動作することを確認します。
EBUS コントローラからの AD 情報 (Slider)を
[故障診断]
LCD の表示の目標値と比較します。
T04 の不良
[テスト方法]
< スライダーが反応しない >
各 Slider を、以下の LCD 表示に従って下 - 上と
滑らかに動かします。
1. PNA シート CN1-6 +5V 電源入力は OK で
すか?
(MASTER) Slider-VR :
2. DM シート CN8 の信号は全て OK で PNA
0(0 or 1) - 127(126 or 127)
シートに I/F されていますか?
(VOLUME) Slider-1 - 4 :
(CN8-1=(H) でスライダー VR 等を動かし
0(0 or 1) - 127(126 or 127) - 64(63-65)
ながら CN8-3、5 の信号が観測出来ます。)
3. PNA シート IC2 のピンで半田ブリッジ等
チェックする Slider の順番は特に指定しません。
はありませんか?
4. PNA シート IC1-1 から +2.5V の基準電圧
は出力されていますか?
5. PNA シート IC2-25 - 35 ピンまでアナログ
入力は OK ですか?
目標値
現在値 スライダー VR を動かした時に関係する
A/D 入力電圧は正しく変化しますか?
[テスト項目]
引っ掛りがなく、数字が滑らかに変化し、OK T05: 1KeyOn チェック
の表示が出ることを確認します。 (テストコード: A00800)
[最初の表示]
[判定結果の表示]
OK
[テスト内容]
NG 表示なし キーボードが正常に動作することを確認します。
EBUS コントローラから鍵盤 ON 情報 <C3>
[判定結果の MIDI コード出力] KeyON と比較します。
OK A0 07 02 <==
NG 出力なし
75
S90ES
[テスト項目]
LCD のテスト結果を確認します。 [テスト内容]
キーボードが正常に動作することを確認します。
[判定結果の表示] EBUS コントローラから鍵盤 ON 情報を LCD 表
OK 示の KeyNo. と比較します。
鍵盤 On 時には受信した情報内の Velocity を表
示します。
After Touch が正常に動作することを確認します。
EBUS コントローラから鍵盤 AfterTouch 情報を
LCD 表示の目標値と比較します。
NG 表示なし
[テスト方法]
[判定結果の MIDI コード出力] A-1 から C7 まで順番に 88 鍵をスケーリングし
OK A0 08 02 <== ます。
NG 出力なし After Touch を、以下の LCD 表示にしたがって
127 - 0 (押す - 放す) と滑らかに動かします。
[テストの終了方法]
C3 鍵が正常にチェックされれば、OK が表示さ
れてテストを終了し、テストナンバー待ち状態
となります。
テスト途中で NG と判断した場合の処理方法 押されたvelocity
目標値
は、"D. NG と判断したときのテストの進め方 " 現在値
を参照してください。 鍵盤検査(C1)の場合
[その他]
なし
[故障診断]
T05 の不良
目標値
現在値
<1KeyON が反応しない >
After Touch 検査
76
S90ES
[テスト方法]
NG 表示なし 以下の LCD 表示にしたがって、
PB の場合 < 中央 > 64(62-65) - < 上 > 127(126 or
[判定結果の MIDI コード出力] 127) - < 下 > 0(0 or 1) と滑らかに動かします。
OK A0 09 02 <== (全ての鍵盤及 AfterTouch MW の場合 < 下 > 0(0 or 1) - < 上 > 127(126 or
が正常の時) 127) と滑らかに動かします。
NG 出力なし BC の場合 < 吹かない > 127(122-127) - < 吹く > 0
(0-5) と滑らかに変化させます。
[テストの終了方法] Extract Plug! と表示されたら、Jack を抜いてくださ
すべての鍵盤が正常にチェックされれば、OK い。
が表示されてテストを終了し、テストナンバー
待ち状態となります。
テスト途中で NG と判断した場合の処理方法
は、"D. NG と判断したときのテストの進め方 "
を参照してください。
目標値
現在値
[その他]
チェックする項目の順番は特に指定しません。
なし
[故障診断]
T06 の不良
77
S90ES
[判定結果の表示]
OK
[テスト内容]
Foot Controller 1/2, Sustain Sw, Foot Sw が正常に
動作することを確認します。
CPU の A/D 入力から入力される Foot Controller
NG 表示なし
1/2 の値を LCD 表示の目標値と比較します。
CPU の Input Port から入力される Sustain 及び
[判定結果の MIDI コード出力]
Foot Switch の ON/OFF を LCD 表示の目標値と
OK A0 0A 02 <==
比較します。
NG 出力なし
[テスト方法]
[テストの終了方法]
Foot Controller 1/2(FC7 を使用)、Sustain Switch
判定を表示、出力してテストを終了し、テスト
(を FC3 使用)を、以下の LCD 表示にしたがっ
ナンバー待ち状態となります。
て 0(0-2) - 127(125-127) (戻す - 押し込む) と滑ら
テスト途中で NG と判断した場合の処理方法
かに動かします。
は、"D. NG と判断したときのテストの進め方 "
(Sustain Switch は、35 以下 - 101 以上)
を参照してください。
Foot Switch(FC4 を使用) を、ON(0)/OFF(1) し
ます。
[その他]
なし
[故障診断]
T07 の不良
目標値 未挿入時には、"Input FC3" 表示
現在値 AD Test 中は表示無し
AD Test 終了後は、"Extract Plus!"
<PB、MW が反応しない >
チェックする項目の順番は特に指定しません。
1. DM シート CN9 の信号は全て OK で PB、
MW に I/F されていますか? [テスト項目]
2. DM シート IC15-1 から +2.5V の基準電圧 数字が変化し、OK の表示が出ることを確認し
は出力されていますか? ます。
3. DM シート IC27-238、239 ピンまで作動
電圧が来ていますか? [判定結果の表示]
OK
<BC が反応しない >
78
S90ES
[テストの終了方法]
判定を表示、出力してテストを終了し、テスト
ナンバー待ち状態となります。
テスト途中で NG と判断した場合の処理方法 [テスト内容]
は、"D. NG と判断したときのテストの進め方 " MIDI IN/OUT/THRU の動作確認を、テストパ
を参照してください。 ターン (AA EF 00 55) によって行います。
CPU のシリアル送信より特定のデータ群を送信
[その他] し、一定時間内に同一のデータ群が受信される
なし ことを確認します。
なお、このテストは MANUAL MODE でのみ実
[故障診断] 行出来ます。
T08 の不良 MIDI MODE は、下記の[その他]を参照して下さい。
一定時間内に受信が終了しない場合
79
S90ES
[テストの終了方法]
判定を表示してテストを終了し、テストナン
[テスト項目]
バー待ち状態となります。
USB Memory を認識することを確認します。
[その他]
[判定結果の表示]
MIDI MODE では、次の方法でチェックを行います。
OK
MIDI によるテストが出来るので、MIDI IN、
OUT のチェックの必要はありません。
THRU は、テストモードでない状態で、本体の
MIDI IN に MIDI コード AA EF 00 55 を入力し
て、THRU から同じ MIDI コードが出力される
ことを確認します。 NG
[故障診断]
T09 の不良
[故障診断]
T10 の不良
[その他]
なし
[テスト内容] [故障診断]
USB (MIDI) が正常に動作することを確認します。 T11 の不良
USB (MIDI) と USB(HOST) を相互接続し、動作
を確認します。 <USB(MIDI)が反応しない >
CPU 内臓の USB Host Controller 経由で S90ES の
接続の有無を確認します。 1. DM シート CN11 の信号は全て OK ですか?
2. DM シート IC27-226、227 からデータ入
[テスト方法] 出力はされていますか?
最初の表示にて[ENTER]を押します。 3. DM シート IC27-223、226 のデータ出力
以下の表示になりますので、その表示を確認し に異常はありませんか?
てから、USB(To DEVICE) 端子と USB(To 4. DM シート IC32-6、8 から +5V が出力さ
HOST) 端子を接続します。 れていますか?
再度、 [ENTER]を押し、テストを実行します。 5. USB ケーブルをテストの最初から入れて
いませんか?
[判定結果の表示]
OK
[テスト内容]
OUTPUT-L、Assignable OUTPUT-L および
PHONES (L) より正常な信号が出力されている
ことを確認します。
Volume を操作し、OUTPUT L の音量が滑らか
NG
に変化することを確認します。
Master 側 SWP50 から Wave ROM の正弦波を発
音させ、指定された出力に出力させます。
Volume Data を DAC に設定し音量を調節します。
誤ったデータが受信された場合
81
S90ES
[判定結果の表示]
OK: 表示なし
NG: 表示なし [テスト内容]
OUTPUT-R、Assignable OUTPUT-R および
[判定結果の MIDI コード出力] PHONES (R) より正常な信号が出力されている
なし ことを確認します。
Volume を操作し、OUTPUT R の音量が滑らか
[テストの終了方法] に変化することを確認します。
MANUAL MODE: Slave 側 SWP50 から Wave ROM の正弦波形を発
[EXIT] ボタンを押すとテストは終了し、[最初の 音させ指定された出力に出力させます。
表示] と同じ画面を表示して、テストナンバー Volume Data を DAC に設定し音量を調節します。
待ち状態となります。
[テスト方法]
MIDI MODE: OUTPUT-L、OUTPUT-R、Assignable-L、Assign-
他のテストのテストコードを送ると、テストは able-R、PHONES(L)、PHONES(R) 共に PLUG
終了し、新たに送られてきたテストコードのテ を差し込み、各出力の周波数、出力波形、出力
ストが実行されます。 レベルを周波数カウンタ、オシロスコープ、レ
[EXIT] ボタンを押すとテストは終了し、(最初の ベル計 (JIS_C フィルター付き) で観測します。
82
S90ES
[判定結果の表示]
[テスト項目]
OK: 表示なし
A/D 入力から D/ A 出力までの信号経路をテス
NG: 表示なし
トします。
(Default で Gain は MIC になっています。
)
[判定結果の MIDI コード出力]
ADC からの入力を SWP50(Master 側)を経由し
なし
DAC に出力させます。
AD Gain は CPU 経由で MIC に設定します。
[テストの終了方法]
MANUAL MODE:
[テスト方法]
[EXIT] ボタンを押すとテストは終了し、[最初の
A/D 入力 L に、1kHz ± 5Hz、-52dBu (歪率 0.1%
表示] と同じ画面を表示して、テストナンバー
以下) の正弦波を入力し、Output L、R から以下
待ち状態となります。
のレベルの出力が得られることを確認します。
MIDI MODE:
他のテストのテストコードを送ると、テストは
終了し、新たに送られてきたテストコードのテ
ストが実行されます。
[EXIT] ボタンを押すとテストは終了し、(最初の 挿入時
非挿入時
表示) と同じ画面を表示して、テストナンバー
待ち状態となります。 [テスト項目]
A/D GAIN VOLUME ツマミを動かし、音量が変
[その他] 化することを確認します。
なし ジャックの抜き差しに応じて、Switch Status が
正しく応答することを確認します。
83
S90ES
[その他]
なし
挿入時
[故障診断] 非挿入時
T14 の不良
[テスト項目]
<A/D -> D/A(MIC)の音が出ない > A/D GAIN VOLUME ツマミを動かし、音量が変
化することを確認します。
1. DM シート IC4 各ピンのデジタル信号は ジャックの抜き差しに応じて、Switch Status が
全て OK ですか? 正しく応答することを確認します。
2. DM シート IC4-2 に正弦波が入力されて OUTPUT L, R から以下のレベルの出力が得られ
いますか? ることを確認します。
3. DM シート CN3 から PNA-AN シート OUTPUT-L: -70.0dBu 以下(負荷 10k Ω)
CN101 の信号線に異常はありませんか? OUTPUT-R: 1kHz ± 5Hz、正弦波、+4.0 ± 2dBu
4. PNA-AN シート IC104-1、IC105-7 の出力 (負荷 10k Ω)(歪率 0.2% 以下)
信号は OK ですか?
5. PNA-AN シート VR100 が MIN になって [判定結果の表示]
いませんか? 表示なし
6. レベルが低い時、TR102、103 が ON して
いますか? [判定結果の MIDI コード出力]
なし
84
S90ES
[故障診断]
T15 の不良
エラーコード
NG_BOARD: VH ボード以外のボードが挿入
されている
NO_BOARD: ノーボード
[テスト内容] (ボードが挿入されていない)
Plug-in Slot 1 の接続チェック、Control Line の送 MIDI: MIDI LINE の異常
受信チェック、MIDI Line のチェック、MEL
Line の IN/OUT チェックを行います。
85
S90ES
[テストの終了方法] [テスト内容]
MANUAL MODE: Plug-in Slot 2 の接続チェック、Control Line の送
[EXIT] ボタンを押すと発音は終了し、さらに 受信チェック、MIDI Line のチェック、MEL
[EXIT] ボタンを押すと OK, NG の判定が表示さ Line の IN/OUT チェックを行います。
れます。 実際には、Insertion Check 後 OK なら、Board
さらに[EXIT] ボタンを押すと、テストナンバー Type Request を行い、Type を受信し、VH Board
待ち状態になります。 かどうか判定します。
判定後、Plug-in の MIDI LINE に TEST CODE を
MIDI MODE: 送信してから、MEL Line の IN/OUT チェックを
他のテストのテストコードを送ると、発音は終 行う為、1kHz 正弦波を Plug-in に出力します。
了し、テスト結果を送信し、新たに送られてき Master 側 SWP50 から Wave ROM の正弦波形を
たテストコードのテストが実行されます。 発音させ Plug In Board(VH) ∼ Master 側 SWP50
[EXIT] ボタンを押すと、次の画面を表示し、テ と経由させ DAC に出力します。
スト結果を送信し、発音は終了します。
さらに [EXIT] を押すとテストコード待ち状態 [テスト方法]
となります。 Plug-in Slot 2 に、Vocal Harmony Plug-in Board を
接続(スロット2ケーブル(黄) )し、Master
[その他] Volume を MAX として、テストを実行します。
なし
[故障診断]
T16 の不良
86
S90ES
[その他]
なし [テスト項目]
OUTPUT L, R から以下のレベルの出力が得られ
[故障診断] ることを確認します。
T17 の不良 OUTPUT L: 1kHz ± 5Hz、正弦波、+6.0 ± 2dBu
(負荷 10k Ω)(歪率 2.00% 以下)
<PLG2 の音が出ない > OUTPUT R: 1kHz ± 5Hz、正弦波、+6.0 ± 2dBu
(負荷 10k Ω)(歪率 2.00% 以下)
1. DM シート IC5 各ピンのデジタル信号は
全て OK ですか? [判定結果の表示]
2. DM シート IC7、8 各ピンの信号線は OK OK 表示なし
ですか?
3. DM シート IC17 の各ピンの信号線は異常 NG
はありませんか?
4. DM シート からのプラグインボード用
+5V 電源は(IC3) C48 の + 端子より出力さ
れていますか?
87
S90ES
[その他]
なし NG の例
[故障診断]
T18 の不良
88
S90ES
[その他] [テスト方法]
なし テストを実行します。
[故障診断] [テスト項目]
T19 の不良 LCD のテスト結果を確認します。
[故障診断]
T20 の不良
89
S90ES
立ち上がらないことが多いです。
1
データバスの開放、ブリッジの場合、立 2
1
2
3 3
ち上がるケースは少ないです。 4 4
5 5
アドレスバスの開放、ブリッジの場合、 6
7
6
7
8 8
途中まで立ち上がる可能性があります。 9 9
10 10
11 11
12 12
13 13
T21: mLAN チェック 14 14
15 15
(テストコード: A01D00) 21 21
22 22
[最初の表示] 24
23
24
23
25 25
26 26
27 27
28 28
29 29
48 48
49 49
50 50
b a
[テスト内容]
mLAN ボード接続コネクタ (DM: CN7) に治具 <PIN側(パターン側)>
90
S90ES
[故障診断]
T21 の不良
MIDI MODE:
他のテストのテストコードを送ると、テストは
終了し、新たに送られてきたテストコードのテ
ストが実行されます。
91
S90ES
[テスト内容]
工場出荷データにセットします。
SDRAM に各パラメータの初期値を書き込んだ
上でそれらのデータを Flash ROM に書き込みま
す。 [テスト内容]
テストモードから抜けます。
[テスト方法] CPU の WatchDogTimer を利用し、CPU を再起
テストを実行します。 動します。
正常に終了すると、正弦波が一瞬発音します。
[テスト方法]
[テスト項目] MANUAL MODE:
なし テストを実行すると、次の画面が表示されます。
[判定結果の表示]
[YES]を押すと、Exit します。
[NO]を押すと、MANUAL MODE のエントリー
[判定結果の MIDI コード出力] 画面に戻ります。
OK A0 1E 02 <==
NG なし MIDI MODE:
MIDI コードを受けたら直ぐにテストモードか
[テストの終了方法] ら抜けます。
判定を表示、出力して終了します。
[テスト項目]
[その他] なし
Factory Set 終了後、次に示すデータがセットさ
れます。 [判定結果の表示]
なし
System Setup:
工場出荷時のデータがセットされます。 [判定結果の MIDI コード出力]
Internal Voice: なし
Factory Set Voice がセットされます。
Internal Performance:
Factory Set Performance がセットされます。
Internal Multi:
Factory Set Multi がセットされます。
92
S90ES
その他: 出荷設定
テストモードを抜けると、通常の電源立ち上げ 出荷時には、本体の各コントローラーは下記の
時と同じシーケンスを行います。 状態に設定されています。
電源ユニットと全てのシート及び鍵盤が接続されて
いる時の電圧、電流は下記の通りです。
但し、オプションなし、ジャック端子は未接続とし
ます。
電源ユニット
コネクタ pin 電圧 電流 接続先
CN2-1 Pin +5 ± 0.3[V] 1300 ± 50[mA] DM
CN2-3 Pin +12 ± 0.6[V] 176 ± 5[mA] AN
CN2-6 Pin -12 ± 0.6[V] 38 ± 5[mA] AN
93
S90ES
■ DATA BACKUP(データのバックアップ)
CAUTIONS 注意意: セーブ/ロード実行中は、USB メモリーを USB
While the data is being saved/loaded, make sure to follow these TO DEVICE 端子から外したり、本体の電源を
precautions: 切らないで下さい。
* Do not unplug or disconnect the USB memory.
楽器本体の故障や USB メモリーの破損の原因に
* Do not turn off the power of the instrument.
なります。
準備
PREPARATION
Tool required for data backup : USB memory USB メモリー
5. Move the cursor to the file name field using the cursor 5. カーソル下ボタンで、ファイルネーム入力欄に
button, then input the desired file name. 移動し、適当なファイル名を入力します。
6. Press the [SF1] EXEC button to actually save the file. 6. [SF1](EXEC)ボタンを押すと、セーブ(バック
After the data has been saved, a “Completed” message アップ)が実行されます。
appears and operation returns to the original display. 画面に "Completed" が表示されるとセーブが終
了し、実行前の表示に戻ります。
データのロード方法
HOW TO LOAD DATA
Procedure 手順
1. Connect the USB memory(w/the backuped data) to the USB 1. バックアップデータ入りの USB メモリーを
TO DEVICE terminal of the main unit. USB TO DEVICE 端子に接続します。
2. Press the [FILE] button to enter the File mode. 2. [FILE]ボタンを押して、ファイルモードに入ります。
3. Press the [F3] LOAD button to call up the Load display. 3. [F3](LOAD)ボタンを押して、ロード画面を呼び
4. Set the Type parameter to “All” using the data dial. 出します。
5. Select the file to be loaded using the cursor button or the
4. データダイアルで TYPE(タイプ)を "ALL" に
data dial.
設定します。
5. カーソルボタン、データダイアルで、ロードす
るファイル名を選択します。
MYDATA .S7V
File to be loaded
(ロードするファイル)
6. Press the [SF1] EXEC button to actually load the file. 6. [SF1](EXEC)を押すと、ロードが実行されます。
After the data has been loaded, a “Completed” message 画面に "Completed" が表示されるとロードが終
appears and operation returns to the original display. 了し、実行前の表示に戻ります。
94
S90ES
■ OS UPDATE(OS のアップデート)
CAUTIONS 注意
Make sure you store your user data before executing the update. ユーザーデータの保存を忘れないようご注意下さい。
PREPARATION 準備
* Tools required for update: USB memory ※ 準備するもの: USB メモリー
* Download the S90ES updated program from the download ※ ヤマハ CS センターホームページのダウンロー
page on the YSISS Homepage to the USB memory.
ドページ にある S90ES 用バージョンアッププロ
(YSISS URL >> http://plaza.yamaha.co.jp/ysiss/exindex.nsf)
グラムを USB メモリーへダウンロードします。
1. Insert the USB memory containing only the upgrade program 1. バージョンアッププログラムみの入った USB メモ
into the USB TO DEVICE terminal on the Rear panel. リーを本体の USB TO DEVICE 端子に挿入します。
2. Turn the power on with "MASTER" button and "STORE" 2. "MASTER" ボタンと "STORE" ボタンを同時に
button pressed and held. 押しながら、本体の電源を ON にします。
(The upgrade screen is displayed on LCD.) (バージョンアップ画面が LCD に表示されます。)
3. Press "ENTER" button after the version check. 3. バージョン確認後 "ENTER" ボタンを押すとプ
The program is updated automatically and the process is ログラムが自動的に更新され、進行状況が LCD
displayed on LCD. (It takes about 4 minutes.) に表示されます。(約4分かかります。)
Press “ENTER”.
5. Remove the USB memory from the terminal. 5. 本体の USB TO DEVICE 端子から USB メモリー
6. Turn the power on with "MASTER" button and "STORE" を抜きます。
button pressed and held again. Make sure of Version. 6. 再度 "MASTER" と "STORE" を押しながら本体
の電源を ON にし、バージョンが上がっている
It is completion above.
ことを確認します。
以上で作業が完了です。
* NOTES <In case the update fails>
After updating, if the system on the S90ES does not opeate
when the power is switched on, update again. ※バージョンアップ作業に失敗した場合
If the software will not update again, repair as follows: (電源を入れても立ち上がらない時)
(1) バージョンアップデータを再ロードしても、
Symptom: System on the S90ES does not operate when the バージョンアップ出来ない事を確認します。
power is switched on. (2) バージョンアップに失敗した場合は、DM シー
ト内 IC37(X6374B00)と IC38(X6373B00)を交
<REPAIR PROCEDURE>
換します。
(1) Replace the FLASH ROM (IC37: X6374B00, IC38:
(3) フラッシュ ROM IC 交換後、バージョンアップ
X6373B00) on the DM circuit board.
データの再ロードを実施します。
(2) After changing, load the new version software of the
program again. (4) 動作確認を行います。
(3) Check the "new version" and system operation.
95
S90ES
CS check of SDRA
CPU INITIALIZE pin 19 of ICs29 and 30
destroyed.
Parameter destructive judgment
(it judges with Flash ROM data)
Initialize SWP50
(Sound generator)
Initialize LCDC
■ 電源立ち上げシーケンス
電源ON
SDRAMのCS確認
CPU 初期化 IC29,30 19ピン
LCD点灯(表示は無し)
SWP50 Reset解除(1回目)
Boot部以外の
(起動時のSW ON状態検知の為)
ProgramのSDRAM
IC27 111ピン
へのコピー実行
パラメータ破壊判断 破壊あり
(Flash ROM上破壊有無判断
データにより判断)
Factory Set 実行
破壊なし (音源管理パラメータ
以外。音源管理パラ
メータ後ほど実行)
各デバイス初期化実行
(mLAN16E,USB(Function), mLAN16E Reset解除 IC27 211ピン
MIDI,SWP50。但しmLAN16E SWP50 Reset∼Reset解除(2回目)IC27 111ピン
は装着時のみ実行)
SWP50(音源)初期化
USB Host初期化
LCDC初期化
パラメータ破壊有りの場合
Factory Set 実行
MOTIF ESバナー表示 (音源管理パラメータ。音源管理
パラメータ以外は既に実行済)
Plug In通信開始
(Plug In装着時のみ)
Now Checking PlugIn表示
立ち上がり
シーケンス終了
TOP画面表示
(表示される画面はUTIL Last Mode設定に従う)
97
S90ES
■ DISPLAY MESSAGES
LCD Indication Description
Are you sure? [YES]/[NO] Confirms whether you want to execute a specified operation or not.
Arpeggio type stored. The current Arpeggio type has been stored to one of the [SF1] - [SF5] buttons.
Bad USB device. The USB storage device is unusable. Format the device and try again.
Bulk protected. Bulk data was received when RcvBulk was set to “protect.” (See page 166.)
Can’t make folder. No more directories can be created below the current level.
Completed. The specified load, save, format, or other job has been completed.
Device number is off. Bulk data cannot be transmitted/received because the device number is set to “off.”
Device number mismatch. Bulk data cannot be transmitted/received because the device numbers don’ t match
Effect plug-in is not in slot 1. The Effect Plug-in board does not work because it has not been installed to slot 1.
Executing... A format operation or job is being executed. Please wait.
File already exists. A file having the same name as the one you are about to save already exists.
File not found. Can’t find the specified type of file.
Folder is too deep. Directories below this level cannot be accessed.
Folder not empty. You have attempted to delete a folder that contains data.
Illegal USB device. USB storage device has been incorrectly formatted.
Illegal file. The file specified for loading is unusable by the S90 ES or cannot be loaded in the current mode.
Illegal file name. The specified file name is unacceptable.
Incompatible USB device A USB device which cannot be used with the S90 ES has been connected to the USB TO DEVICE connector.
MIDI buffer full. Failed to process the MIDI data because too much data was received at once.
MIDI checksum error. Error occurred when receiving bulk data.
MIDI data error. Error occurred when receiving MIDI data.
Multi plug-in is not in slot 3. The Multi-Part Plug-in board does not work because it has not been installed to slot 3.
No response from USB device. There is no response from the USB device connected to the USB TO DEVICE terminal.
Not empty folder. You have attempted to delete a folder that contains data.
Now checking plug-in board. The S90 ES is checking the Plug-in board installation status during power-on.
Now loading... (xxxx) Indicates that a file is being loaded.
Now saving... (xxxx) Indicates that a file is being saved.
Now scanning autoloaded files. Scanning for the files specified for Auto Load.
Now working... Executing the memory arrangement after canceling the Load/Save operation by pressing the [EXIT] button.
Overwrite? [YES]/[NO] A save operation will overwrite data on the USB storage device, and this message confirms whether it is OK to
continue or not. Press [INC/YES] or [DEC/NO] as required.
Please keep power on. The data is being written to inter nal memory. Never attempt to turn off the power while data is being written to
internal memory. Turning the power off while this message is shown results in loss of all user data and may
cause the system to freeze. This may also result in the S90 ES being unable to properly start up the next time the
power is turned on.
Please stop sequencer. The operation you’ve attempted to execute cannot be done during sequencer playback.
PLG100 not supported. The Plug-in All Bulk Save function does not apply to the PLG100 series boards.
Plug-in1 communication error. The Plug-in board that has been installed to slot 1 does not work.
Plug-in1 type mismatch. The User Voice created by using the Plug-in boar d previously installed to slot 1 (but now removed from slot 1)
has been selected.
Plug-in2 communication error. The Plug-in board that has been installed to slot 2 does not work.
Plug-in2 type mismatch. The User Voice created by using the Plug-in board previously installed to slot 2 (but now removed from slot 2)
has been selected.
Plug-in3 communication error. The Plug-in board that has been installed to slot 3 does not work.
Plug-in3 type mismatch. The User Voice created by using the Plug-in board previously installed to slot 3 (but now removed from slot 3)
has been selected.
Power on mode stored. The setting of the program number automatically selected when turning the power on has been stored.
Read only file. You have attempted to delete, rename, or overwrite a read-only file.
Receiving MIDI bulk. The S90 ES is receiving MIDI bulk data.
System memory crashed. Writing data to internal Memory has failed
This performance uses user voices. The performance you have loaded includes User voice data. Check whether the voice you saved exists at the
appropriate User voice bank.
Too many favorites. You’ve attempted to assign more than 257 voices to the Favorite category.
Transmitting MIDI bulk. The S90 ES is transmitting MIDI bulk data.
Unknown file format. File format is not recognized.
98
S90ES
99
S90ES
■ ディスプレイメッセージ
LCD 表示 説明
Are you sure ?[YES]/[NO] 各操作を実行したときの、確認を求める表示です。
Completed. ロード、セーブ、フォーマット、ジョブなどの実行が完了したときに表示されます。
Device number is off. デバイスナンバーがオフなので、バルクデータを送 / 受信できません。
ザーデータが失なわれたり、システムが壊れて次に電源を入れたときに正常に立ち上がらなくなるれがあります。
Please stop sequencer. シーケンサーを停止してから操作してください。
表示されます。
ンクの同じ場所にストアされているかご確認ください。
100
S90ES
LCD 表示 説明
Too many favorites. フェーバリットカテゴリーに上限(256)を超えるボイスを登録しようとした場合に表示されます。
るか、不要なファイルを消去してから操作をやりなおしてください。
USB 記憶装置の内容を確認してください。
USB device write protected. USB 記憶装置が書込み禁止状態になっているか、または CD-ROM ドライブなどへの書き込みを行なおうとし
た場合に表示されます。
101
S90ES
Default ҂ ҂
Mode Messages ҂ ҂
Altered ************** ҂
Note 0 - 127 ҂
Number : True voice ************** ҂
After Key's 쑗 ҂
Touch Ch's 쑗 ҂
Pitch Bend 쑗 ҂
0-121 쑗 ҂
Control
Change
Prog 쑗 0 - 127 ҂
Change : True # **************
System Exclusive 쑗 ҂
: Song Pos. 쑗 *1 ҂
Common : Song Sel. ҂ ҂
: Tune ҂ ҂
System : Clock 쑗 *2 쑗 *3
Real Time : Commands 쑗 *1 쑗 *1
: All Sound Off 쑗 ҂
Aux : Reset All Cntrls 쑗 ҂
: Local ON/OFF 쑗 ҂
Mes- : All Notes OFF 쑗 ҂
sages: Active Sense ҂ ҂
: Reset ҂ ҂
102
S90ES
Default 3 1 Memorized
Mode Messages ҂ 1 - 4(m=1) *2
Altered ************** ҂
After Key's ҂ ҂
Touch Ch's 쑗 쑗 *1
Pitch Bend 쑗 쑗 *1
System Exclusive 쑗 쑗
: Song Pos. ҂ ҂
Common : Song Sel. ҂ ҂
: Tune ҂ ҂
System : Clock ҂ 쑗
Real Time : Commands ҂ ҂
103
S90ES
Additional Notes
• For example, 144 - 159(Decimal)/9nH/1001 0000 - 1001 1111(Binary) indicate the note-
on messages for the channels 1 through 16 respectively. 176 - 191/BnH/1011 0000 -
1011 1111 indicate the control change messages for the channels 1 through 16
respectively. 192 -207/CnH/1100 0000 - 1100 1111 indicate the program change
messages for the channels 1 through 16 respectively. 240/F0H/1111 0000 is positioned
at the beginning of data to indicate a system exclusive message. 247/F7H/1111 0111 is
positioned at the end of the system exclusive message.
• aaH (Hexadecimal)/0aaaaaaa (Binary) indicates the data addresses. The data address
consists of High, Mid and Low.
104
S90ES
105
S90ES
PORTAMENTO TIME sets the time it takes for the pitch to reach the next note played when PORTAMENTO First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.
SWITCH is set to on.
RPN D.ENTRY
PAN position relatively changes accor ding to the pr eset value for each voice.
LSB MSB MSB LSB PARAMETER NAME DATA RANGE
EFFECT1 DEPTH controls reverb send level.
EFFECT3 DEPTH controls chorus send level. 00H 00H mmH --- PITCH BEND SENSITIVITY 00H-18H (0-24 semitones)
HARMONIC CONTENT adjusts the resonance preset for each voice. Setting a value adds to or subtracts fr om 01H 00H mmH llH MASTER FINE TUNE {mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}
the center value, 64, since it is an offset parameter. The larger the value more resonant sound will be pr oduced. (-8192*100/8192)-0-(+8192*100/8192)
The effective range may be narr ower than the range you can designate depending on the selected voice. 02H 00H mmH --- MASTER COARSE TUNE 28H-40H-58H (-24-0-+24 semitones)
The parameters, EG ATTACK TIME, EG DECAY TIME, EG SUSTAIN LEVEL, EG RELEASE TIME adjust the 7FH 7FH --- --- RPN RESET
envelopes preset for each voice. Setting these values add to or subtract fr om the center value, 64, since these RPN numbers will be left not designated.
are offset parameters. The internal values are not affected.
BRIGHTNESS adjusts the cutof f frequency pr eset for each voice. Setting a value adds to or subtracts fr om the
center value, 64, since it is an offset parameter. The smaller the value the cutoff frequency will be lower ed. The
effective range may be narrower than the range you can designate depending on the selected voice.
(3-4) NON-REGISTERED PARAMETER NUMBER
Bank Select will be actually executed when the Pr ogram Change message is r eceived. Bank Select and
Program Change numbers that ar e not suppor ted by Yamaha will be ignored, but transmitted to the Plug-in There are no applicable parameters.
board. These are transmitted to the Plug-in board.
Resets the values set for the following controllers. (3-6-1-3) IDENTITY REPLY (Transmit only)
PITCH BEND CHANGE 0 (center)
CHANNEL AFTER TOUCH 0 (minimum) F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H
MODULATION 0 (minimum)
dd; Device Number Code
EXPRESSION 127 (maximum)
S90 ES: 32 06
BREATH CONTROLLER 127 (maximum)
FOOT CONTROLLER 127 (maximum)
Assign A 0 (center) (3-6-2) UNIVERSAL REALTIME MESSAGE
Assign B 0 (center)
Assign 1 0 (center) (3-6-2-1) MIDI MASTER VOLUME
Assign 2 0 (center)
F0H 7FH 7FH 04H 01H llH mmH F7H
SUSTAIN SWITCH 0 (off)
SOSTENUTO SWITCH 0 (off)
Sets the MASTER VOLUME value.
RPN Not assigned; No change The value “mm” is used to set the master volume (the value “ll” should be ignor ed).
Doesn’t reset the following data:
PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, SUSTAIN LEVEL, (3-6-3) PARAMETER CHANGE
RELEASE TIME, ATTACK TIME, DECAY TIME, BRIGHTNESS, EFFECT SEND LEVEL 1, EFFECT SEND LEVEL 3,
PORTAMENTO SWITCH, PITCH BEND SENSITIVITY , FINE TUNING, COARSE TUNING (3-6-3-1) XG SYSTEM ON
11110000 F0 Exclusive Status
(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0) 01000011 43 YAMAHA ID
All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain 0001nnnn 1n Device Number
or Sostenuto is on, notes will continue sounding until these are turned off. 01001100 4C Model ID
0aaaaaaa 0 Address High
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0) 0aaaaaaa 0 Address Mid
0aaaaaaa 7E Address Low
Performs the same function as when receiving ALL NOTES OFF.
0 0 Data
Sets VOICE RECEIVE CHANNEL to “OMNI OFF,” channel 1.
11110111 F7 End of Exclusive
(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0) The PLG100-XG Plug-in board installed to the instrument, will receive this message when the instrument is in the
Multi mode and SYSTEM Receive GM/XG is set to on. The Par t values will be reset according to the SYSTEM
Perfor ms the same function as when receiving ALL NOTES OFF.
Internal Part settings.
Sets VOICE RECEIVE CHANNEL to “OMNI ON.”
The internal tone generator block will not r eceive this message.
Be aware that executing this message takes about 170 ms, and that an appr opriate interval must be allowed
(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0..16) before executing the subsequent message.
Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16,
the channel will be Mode4 (m = 1).
(3-6-3-2) NATIVE PARAMETER CHANGE, MODE CHANGE
In the Voice mode, the mode can be Mode2 (m = 1) accor ding to VOICE RECEIVE CHANNEL. 11110000 F0 Exclusive Status
01000011 43 YAMAHA ID
(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0) 0001nnnn 1n Device Number
01111111 7F Model ID
Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode3. 00000000 00 Model ID
In the Voice mode, the mode can be Mode1 accor ding to VOICE RECEIVE CHANNEL.
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaa Address Mid
0aaaaaaa aaaaaaa Address Low
(3-3) REGISTERED PARAMETER NUMBER 0ddddddd ddddddd Data
| |
STATUS 1011nnnn(BnH) n = 0 – 15 CHANNEL NUMBER 11110111 F7 End of Exclusive
LSB 01100100(64H)
RPN LSB 0ppppppp p = RPN LSB (Refer to the table as shown below.) For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
MSB 01100101(65H) See the following MIDI Data Table for Addr ess and Byte Count.
RPN MSB 0qqqqqqq q = RPN MSB (Refer to the table as shown below.) In the REMOTE SWITH, the Device Number will be received regardless of the value.
DATA ENTRY MSB 00000110(06H)
DATA VALUE 0mmmmmmm m = Data Value
DATA ENTRY LSB 00100110(26H)
DATA VALUE 0lllllll l = Data Value
106
S90ES
See the following BULK DUMP Table for Addr ess and Byte Count.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address,
Data and Check sum itself are added.
See the following DUMP REQUEST Table for Addr ess and Byte Count.
From USB/mLAN
Local Sw
MIDI Out
MIDI In
TG
From USB/mLAN
Thru Port
Local Sw
MIDI Out
MIDI In
TG
Although three types of note on/note off data, received via MIDI, played by the internal sequencer and played on the
keyboard will be distinguished, the other controllers (channel messages) equally af fect the entire notes.
ALL SOUND OFF clears all the sounds in the specific channel(s) played by both the keyboard and the data via MIDI.
ALL NOTES OFF received via MIDI clears the sounds in the specific channel(s) played via MIDI.
107
PARTS LIST
CONTENTS(目次)
OVERALL ASSEMBLY (総組立) ............................................. 2
WHEEL ASSEMBLY(ホイールAss’y) ...................................... 5
CONTROL PANEL ASSEMBLY(コンパネAss’y) .................... 6
KEYBOARD ASSEMBLY(HEDaf_EBUS鍵盤) ...................... 10
ELECTRICAL PARTS(電気部品) .......................................... 12
Note) DESTINATION ABBREVIATIONS
WARNING
Components having special characteristics are marked and must be replaced with parts having
specifications equal to those originally installed.
印の部品は、安全を維持するために重要な部品です。交換をする場合は、安全のため必ず指定の
部品をご使用下さい。
20
Control panel assembly (See page 6)
10 コンパネAss'y(6ページ参照)
20a
140
22 80
20b 80a
120
20c
80d 80b
35 110
12 200
80c 130 50
Wheel assembly (See page 5) 42
ホイールAss'y(5ページ参照) 80d
52 32
30b 210
202
B90 B100 30d
82 B80
40
B70 30c
B80 110
Keyboard assembly B40 30a
B70
(See page 10)
鍵盤Ass'y 35
(10ページ参照) 30
30e
B43 42
B22
B42
B46
B20 B44
B10d
B10
B36 B22
B10f
B10a
B10b
B10c
A30
B30
A10
B32
A20 B60
B34
2
S90ES
3
S90ES
JIGS 工 具 S90ES
TX000670 Rod Service Tool ロ ッ ド 99
V6295700 Stay Service Tool ス テ イ 05
VB299400 Screw Service Tool サービス用ツール(ネジ)
4
S90ES
80
10
70
VR an assembly
(VR付属品)
90 20
60 40
80
10
VR an assembly
(VR付属品)
90
50 20
30
40
5
S90ES
112 110
80
210
330
310
312
190 204
320 260 102
86 100
220
270 162 161
72
90 50d 50e
50h 50f 50
92 50h
94 280 50k
300 240
92 74
290 250
160 50j
50c
50g
20 50i
50f 50a
96 50h
50b 50g
40f 52
40a 52 70
40d
D40b D10 40c
40 250 70e 70c
D40c D40
40c
D40a 70a
40e
D30
202 70d
70b
40b 40b 202
42 71
71
D20 160 200d
D50a 160
200c
D50b 22
42
235
D50
200b
200
D60
200a
230 202
6
S90ES
50
● PNB SHEET ASSEMBLY(PNBシートAss’y)
50c
50e
50h
50h
50g
50g
50h
50i 50f 50d 50b
40e 40a
40f
40c
40d
40b
7
S90ES
8
S90ES
9
S90ES
80 Adhesive Tape
(両面テープ)X1
20 30
40 50
70
60 Service Tool
360
(サービス用ツール)
110
VB299400
350
10
100
270 390
222
300 210
260 280
P10 P60
224 P20
310
240
230
260
300 The first lot only
235 (第1ロットのみ)
310 260
260 400
300
260 240
315
262
The second lot or later
260 (第2ロット以降)
190
150
10
S90ES
11
S90ES
■ ELECTRICAL PARTS(電気部品)
REF NO. PART NO. DESCRIPTION 部 品 名 REMARKS QTY RANK
ELECTRICAL PARTS 電 気 部 品 S90ES
* WE260600 Circuit Board DM D M シ ー ト (X6083C0)
V6774600 Circuit Board GHDPC G H D P C シ ー ト (V677410)(XY986E0) 09
V6469400 Circuit Board GHD_EBUS H GHD_EBUSシートH The 1st lot only (XZ139C0) 11
* V8612300 Circuit Board HEDaf_H H E D a f _ H シート The 2nd lot or later (X2218A0)
* V8612200 Circuit Board HEDaf_M H E D a f _ M シート The 2nd lot or later (X2217A0)
V6469300 Circuit Board GHD_EBUS L GHD_EBUSシートL (XZ138D0) 12
V6588200 Circuit Board MK SUB M K サ ブ シ ー ト (V658810)(XZ142B0) 10
* WE630600 Circuit Board PNA-AN PNA−ANシート (WE26070)(X6085C0)
* WE630500 Circuit Board PNA-PN PNA−PNシート (WE26070)(X6085C0)
* WE630700 Circuit Board PNB-PN PNB−PNシート (WE26080)(X6086C0)
* WE630800 Circuit Board PNB-PW PNB−PWシート (WE26080)(X6086C0)
12
S90ES
13
S90ES
14
S90ES
15
S90ES
16
S90ES
17
S90ES
18
S90ES
19
S90ES
20
S90ES
21
S90ES
V6469400 Circuit Board GHD_EBUS H GHD_EBUSシートH The 1st lot only (XZ139C0) 11
CN2 VB389900 Connector Base Post PH 3P TE コネクタベースポスト 01
VF667600 Wire Trap 52147 15P TE ワ イ ヤ ー ト ラ ッ プ 01
VK025300 Wire Trap 52147 9P TE ワ イ ヤ ー ト ラ ッ プ 01
D1 VB941200 Diode 1SS133,1SS176 TE- ダ イ オ ー ド 01
-108 VB941200 Diode 1SS133,1SS176 TE- ダ イ オ ー ド 01
-- Dust Proof Cloth 不 織 布 (VU45980)
J -- Jumper Wire 0.55 TIN ジ ャ ン パ ー 線 (VA07890)
22
S90ES
23
S90ES
24
S90ES
25
S90ES
26
S90ES
27
S90ES
28
A B C D E F G H I J K L
<P.1>
1 1
R22 SW LED PNA-PN PNB-PN The 1st lot only The 2nd lot or later
+5D MATRIX
D0-6 RD SW LED
CN3-2P
BACKLIGHT LD1-5 SW1-17
L3-9 EC1 MATRIX
MK SUB GHD-EBUS L GHD-EBUS H HEDaf_M HEDaf_H
D0-7 +5D
CN4-30P
CN1-30P
L10 L3-9 S0-7 LD1-51 SW1-58 MK00-05 +5D +5D +5D +5D +5D
CN2-15P
CN1-15P
MK00-05
CN3-15P
CN1-15P
CN3-15P
CN1-15P
CN1-12P
CN5-12P
RD,S0,1
,MK10-15 ,MK10-15 MK00-05 MK00-05 MK00-05
L3-10
MK00-05
GHD-EBUS L
D0-7
MK00-05 ,MK10-15 MK00-05 ,MK10-15 ,MK10-15
LCD Display
RD
,MK10-15 ,MK10-15 MK00-05
+5D ,MK10-15 AFTER AFTER ,MK10-15 AFTER
SW1- 68
AFTER
8.38MHz SW1-108 SW1- 60 SW61-108
TA2 TA1
2 +5A 10,24 2
D0-7
S0-7
L3-9
+5D
S0-7
(VDD) 40,41 A-1 - F#2 G2 - C7 G2 - C5 C#5 - C7
CN1-12P +5D +5D
CN3-24P
CN4-24P
BK0-5
CN4-4P
CN3-4P
CN2-9P
CN3-9P
CN2-9P
CN3-9P
8 IC1(8P) IC1 BK6-10
43-50 55-62 54 1-8 BK0-14 BK0-14 BK6-14 BK6-14 BK6-14 BK11-14
10
WHEEL 3 Buffer
1
Slider VR1,2,3,4,5 ANI 0,1,2,3,5,7 26,28
26 AFTER AFTER AFTER
2 E-Bus E-Bus +5D
30-33 LED Driver 36 13,14 +5D +5D
ANI 1
ANI 0
ANI 7
ANI 3
ANI 5
ANI 2
AFTER
MASTER
34 40,41 RESET +5D +5D
Switch Scan CN1-7P CN2-3P CN2-3P
+5A
IC2(64P) 8.38MHz
CONT VR
35
CN1-3P CN1-3P
13,14,36
VR6 1 2 3 4
AVDD GHD PC GHD PC
AVREF E-Bus +5D +5D +5D
+5D ( SDA,SCL,E-IC )
(VDD)
+5D
SENSOR
+5D
USB AFTER
SENSOR
CN2-3P CN5-4P CN1-7P
E-Bus DETECT
3 AFTER 3
TO HOST TO DEVICE
DETECT
CN9-5P CN10-12P CN14-3P CN1-4P CN8-7P
USB2_Dm,Dp
PB,MW
E-Bus ( SDA,SCL,E-IC )
+3.3D
USB1_pwr_en
+5D
USB_VBUS
6,8
IC32 2 +3.3D PNA-AN
9 8 5 6 +5D IC101(8P)
1 IC35 1
2 20 2-9 CONTRAST -12D
TR100
IC13
USB2_overcurrent
7
IC28 TR6,7 5
USB2_power_en
12
8
13 11-19
/RESET
IC9
11 10 12
/RESET 11 5 6 PHONES
13 +12A TR101
11
3 1
9
/RESET 6 8 4
IC14
IC103(8P)
4
/MUTE MUTE +12A -12A TR106
JK105
9
2 1
+3.3D (to CN3 ) AMP
3 OUTPUT
-12A
R
/RESET
CN101-30P
SWPRES CDTI 11 AOUTL,R 2
CN3-30P
AD4 205 Address 1,3,9,14
CONTROLER 1 VCC-INT IC27(240P) D0-31 C14 MASTER 27,43,49 3 AMP ASSIGNABLE
+3.3D (A1-22) [0-13]
JK3 TXD0 128FS,WCLK1,MELO 4 OUTPUT R
191 MAIN CPU IC29
FOOT 3 RXD0 SMUTE DATA SDRAM MUTE
2 [0-15] +3.3D +5A MUTE TR105
AD3 198 Internal 128MHz 114
+3.3D D0-15 +3.3D 64M 7 JK104
CONTROLER 2 D0-31 5
External 64MHz +3.3D +3.3D AMP
16MHz 48MHz
Address[0-23]
*C 37 3 TR1,2 GAIN GAIN 8 4
Data[0-15]
AD5 26,45 26,45 IC6
12
Address[1-16]
BREATH IC33 IC37,38 IC42,43 IC44,45 20-23 ADGAIN +12A -12A
Data[0-15]
+3.3D AD6,AD7
179,180 (86P) (48P) MASK ROM MASK ROM IC41 (from IC27-113)
238,239
JK6 +5D 256M 16Bit 256M 16Bit 8 1 DAC GAIN
6 DC/DC +5D SMUTE IC105(8P) IC104(8P)
SDRAM FLASH JK101
JKIN1,2
212,213,233-236 CS 2 8 VR100
1 5 107 20 64Mbit ROM +1.5D DGND
MIDI IN IC30 IC14 CKE 1 3 7 5
3 13 10 128 67 32Mbit AMP AMP
201 CKIO(64MHz)
189 68 6
A/D INPUT-R
+5D +5D +5A
+5D SWPRES
6 14 111 C14 6
10 6
113 ADGAIN SA0-5,SD0-7 7 7 5 1 3
MIDI OUT 195 119,120 ADIN1,2 AMP AMP JK102
8
9 128FS,WCLK1,MELO 4 IC31 IC4 2
135 19 +3.3D 1
10-12 4 8 TR103 4 8
IC10 CKIO(64MHz) SWP50 2
TR8 /RESET SLAVE Address 1,3,9,14 MELI 4 ADC -12A +12A TR102 -12A +12A A/D INPUT-L
12 SIORES +3.3D 27,43,49 9
[0-13]
MIDI THRU 11 +3.3D 20 +5D +5D IC36 TR102,103: ON - MIC JKIN1,2
13 11-13 DATA SDRAM JKIN1,2
IC8 DGND OFF - LINE
[0-15] 64M
TX0-2,128FS,WCLK1,MELO 4 +5V <- 3V TX0-2 15 43 41 30 43 41 30 2 1 JKIN1
WCLK0,RFCLK0,MBCLK
3-5 15-17 17
21 IC14 -12A +12A DGND
MELI 0-2 3 JKIN2 (-12V) (+12V)
+3.3D 20 16-18 SIO4 ADIN1,2
SIO4 4
(to IC27-119,120)
IC7 IC17
TX0,128FS,WCLK1,MELO 4
IC16
RX0-2,MELI 0-2 +5V -> 3V RX 0-2 14
16
CN100-3P
5-7 13-15
MELO[0-7]
20
7 7
MELI[0-7]
32 32
TX30-32 23
25 34 34 -12V
,WCLK1<MELO 4
27
,WCLK1,MELO 4
CN200-10P
+12V POWER INLET
CN201-6P
,1RX[0-2],30
1TX[0-2],30
GND
RX1,MELI 1
CN1-4P
CN2-6P
RX0,MELI 0
RX2,MELI 2
GND
TX1,128FS
TX2,128FS
CN2-7P
2012,15,17 20 11-18 20 11-18 IC2(32P) +12V +12V
POWER
TX31
11-14
TX32
RXD0
+5V 11-14 6,17-20 3,5,8 2-9 2-9 +3.3D FZ1 ( +5V ) GND +5V +5V
+12V GND
DC/DC +5D(+5V) +5D
(to CN1) +5V
PNB-PW
+5V
CN4-15P CN5-15P CN6-15P CN7-100P
15P 15P 15P 100P
Plug-in Plug-in Plug-in
mLAN 16E
8 Board Board Board 8
OPTION
28CA1-2000000925
S90ES S90ES
A B C D E F G H I J K L
A B C D E F G H I J K L
<P.2>
16 19
17 20
WHEEL Assembly
(ホイールAss'y)
D0 D1 D2 D3 D4 D5 D6 D7
SW 1 SW 9 SW17 SW22 SW30 SD38 SW46 SW54
S0 (DEC/NO) (VOICE) (MASTER) (PRE1) (PRE3) (GM) (PLG2) (CATEGORY SEARCH)
6 SW 2 SW10 SW18 SW23 SW31 SW39 SW47 SW55 6
S1 (<) (SEQ PLAY) (UTILITY) (A) (C) (E) (G) (TRACK SELECT)
SW 3 SW11
1 SW19 SW24 SW32 SW40 SW48 SW56
S2 (EXIT) (EDIT) (STORE) (1) (3) (5) (7) (MUTE)
SW 4 SW12 SW20 SW25 SW33 SW41 SW49 SW57
S3 V
(V) (REMOTE) (ARPEGGIO ON/OFF) (9) (11) (13) (15) (USER1) PNB-PW
SW 5 SW13 SW21 SW26 SW34 SW42 SW50 SW58 PNB-PN
S4 (V) (PERFORM) (DRAM KIT) (PRE2) (PRE4) (PLG1) (PLG3) (USER2) SWITCH
SW 6 SW14 SW27 SW35 SW43 SW51
S5 (INC/YES) (FILE) (B) (D) (F) (H)
SW 7 SW15 SW28 SW36 SW44 SW52
S6 (>) (JOB) (2) (4) (6) (8)
SW 8 SW16 SW29 SW37 SW45 SW53
S7 (ENTER) (EFFECT BYPASS) (10) (12) (14) (16)
S8 SW 2 SW 4 SW 6 SW 8 SW10 SW12
(SF1) (SF2) (SF3) (SF4) (SF5) (INFORMATION)
SW 3 SW 5 SW 7 SW 9 SW11 SW13
S9 (F1) (F2) (F3) (F4) (F5) (F6) PNA-PN
S10
SW 14 SW 15 SW 16 SW 17 SW1 SWITCH GHDPC
(PAN/SEND) (TONE) (ARP/FX) (EQ) (VOLUME)
7 7
D0 D1 D2 D3 D4 D5 D6 D7
LD47 LD1 LD8 LD12 LD19 LD26 LD33 LD40
L3 (SLOT2) (VOICE) (MATER) (PRE1) (10) (4) (F) (PLG3) The 1st lot only
LD48 LD2 LD9 LD13 LD20 LD27 LD34 LD41 GHD-EBUS L MK SUB GHD-EBUS H
L4 (SLOT3) (SEQ PLAY) (UTILITY) (A) (PRE3) (12) (6) (H) (第1ロットのみ)
LD49 LD3 LD10 LD14 LD21 LD28 LD35 LD42
L5 (CATEGORY SEARCH) (EDIT) (ARPEGGIO ON/OFF) (1) (C) (GM) (14) (8)
LD50 LD4 LD11 LD15 LD22 LD29 LD36 LD43
L6 (TRACK SELECT) (REMOTE) (DRAM KIT) (9) (3) (E) (PLG2) (16) PNB-PN
LD51 LD5 LD16 LD23 LD30 LD37 LD44 LED
L7 (MUTE) (PERFORM) (PRE2) (11) (5) (G) (USER1)
LG6 LD17 LD24 LD31 LD38 LD45
L8 (FILE) (B) (PRE4) (13) (7) (USER2)
LD7 LD18 LD25 LD32 LD39 LD46
L9 (EFFECT BYPASS) (2) (D) (PLG1) (15) (SLOT1)
8 LD1 LD2 LD3 LD4 LD5 8
PNA-PN
L10 (PAN/SEND) (TONE) (ARP/FX) (EQ) (VOLUME)
LED
The 2nd lot or later
GHD-EBUS L MK SUB HEDaf_M HEDaf_H (第2ロット以降)
S90ES S90ES
A B C D E F G H I J K L
A B C D E F G H I J K L
<P.3>
WHEEL Assembly
S90ES CIRCUIT DIAGRAM 1/7 (DM 1/2) FOOT SWITCH FOOT CONTROLLER LCD MIDI USB S90ES
Display
BREATH ASSIGNABLE SASTAIN 2 1 MIDI IN THRU TO DEVICE TO HOST
FOOT PEDAL to PNA-PN-CN2 MIDI OUT
CN1 <P.5 K-2>
1 1
DM 1/2
Not installed
BUFFER
INVERTER
RESET
PHOTO COUPLER
to PNA-PN-CN5
<P.5 J-3>
TRANSCEIVER
Not installed
AND
INVERTER
to PNB-PW-CN200
<P.7 F-2>
2 OR 2
DC/DC CONVERTER OP AMP INVERTER Not installed
INVERTER
AND
Not installed
PLUG IN BOARD
AREA4
3 TRANSCEIVER SIO4 3
Not installed
CPU
TRANSCEIVER
2
4 4
Not installed
SIO4
1 : ANODE
2 : CATHODE
1:ANODE
5 2:CATHODE 5
to PNA-AN-CN101
AND
to GHD-EBUS L-CN1 HSU119(V9599200)
<P.6 K-4> DIODE
<P.8 B-3> INVERTER DM:D0008
<P.9 B-3>
1
DECORDER
ADC
Not installed
2
Not installed
Not installed
1 : ANODE
2 : CATHODE
LMS8117AMP-ADJ (X0609A00)
6 SDRAM REGULATOR 6
DM: IC034
SDRAM 64M
64M TAB IS
VOUT
mLAN CN
SWP50
SWP50 (SLAVE)
TRANSCEIVER (MASTER) 1
2
3
1: ADJ/GND
2: OUTPUT
3: INPUT
NJM78M05DL1A (XS534A00)
REGULATOR +5V
DM: IC0001
Not installed
7 Not installed
2 7
1
3
1: V in
2: GND
to PNA-PN-CN1
3: V out
Not installed
Not installed
28CC1-2000000946-1 1
8 8
A B C D E F G H I J K L
A B C D E F G H I J K L
<P.4>
1 1
DM 2/2
DC/DC CONVERTER
2 2
SWP50
(MASTER)
MASK ROM
(WAV1)
3 3
SWP50
(MASTER)
4 4
MASK ROM
(WAV2)
Not installed
5 5
7 7
MASK ROM
(WAV4)
28CC1-2000000946-2 1
8 8
A B C D E F G H I J K L
A B C D E F G H I J K L
<P.5>
1 1
PNA-PN
2 2
to DM-CN14
<P.3 G-1>
LCD
Display
3 3
to DM-CN1
<P.3 A-2>
4 4
to PNB-PN-CN1
5 <P.7 D-2> 5
6 6
2
1: ANODE
2: CATHODE
OP AMP
7 7
28CC1-2000000947-1 1
8 8
A B C D E F G H I J K L
A B C D E F G H I J K L
<P.6>
1 1
PNA-AN
2 2
OP AMP
3 3
PHONES
OP AMP
4 4
OP AMP
to DM-CN3
<P.3 A-5>
5 OP AMP 5
6 6
GAIN
OP AMP
to PNB-PW-CN200
<P.7 F-2>
AGND GUARD
28CC1-2000000947-2 2
8 8
(金被): Metal Film Resistor(金属皮膜抵抗)
(マ): Mylar Capacitor(マイラーコンデンサー)
: Electrolytic Capacitor(ケミカルコンデンサー)
: Ceramic Capacitor(セラミックコンデンサー)
S90ES S90ES
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストを御参照ください。
A B C D E F G H I J K L
A B C D E F G H I J K L
<P.7>
1 1
PNB-PW
2 2
to PNA-PN-CN4
<p.5 K5>
POWER INLET
to DM-CN2
CN2
CN1
<P.3 A-2> AC
<P.6 K-7>
Power Supply Unit POWER
ON/OFF
PNB-PN
28CC1-2000000948-2
3 3
4 4
5 5
6 6
7 7
28CC1-2000000948-1
8 1 8
1: ANODE
2: CATHODE
S90ES S90ES
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストを御参照ください。
A B C D E F G H I J K L
A B C D E F G H I J K L
<P.8>
1 1
OP AMP
2 2
OP AMP
3 3
28CC1-8819027 28CC1-8818010 3
to DM-CN8
<P.3 A-5>
GHD-EBUS L
(A-1- F#2)
4 4
5
MK SUB 5
6 6
CPU
7 7
2
1: ANODE
2: CATHODE
28CC1-8819027 28CC1-8819224
8 8
(セ):Ceramic Capacitor(セラミックコンデンサ)
S90ES S90ES
Note: See parts list for details of citcuit baord component parts.
注:シートの部品詳細はパーツリストを御参照ください。
A B C D E F G H I J K L
A B C D E F G H I J K L
<P.9>
S90ES CIRCUIT DIAGRAM 7/7 (HEDaf_H, HEDaf_M, GHD_EBUS L, GHDPC, MK SUB) S90ES
HEDaf_M HEDaf_H
(G2 - C5) (C#5 - C7) GHD PC
OP AMP
2 2
OP AMP
3 3
28CC1-8818010 3
28CC1-8822377 28CC1-8822378
to DM-CN8
<P.3 A-5>
GHD-EBUS L
(A-1 - F#2)
4 4
5
MK SUB 5
6 6
CPU
7 7
2
1: ANODE
2: CATHODE
28CC1-8819027 28CC1-8819224
8 8
(セ):Ceramic Capacitor(セラミックコンデンサ)
S90ES S90ES
Note: See parts list for details of citcuit baord component parts.
注:シートの部品詳細はパーツリストを御参照ください。
A B C D E F G H I J K L