Professional Documents
Culture Documents
Hfe Denon dn-s3700 Service
Hfe Denon dn-s3700 Service
SERVICE MANUAL
MODEL JP E3 E2 EK E2A E2C E1K EUT
DN-S3700 3 3
CD/USB MEDIA PLAYER & CONTROLLER
●
For purposes of improvement, specifications and design are subject to change without notice.
●
Please use this service manual with referring to the operating instructions without fail.
● Some illustrations using in this service manual are slightly different from the actual set.
LASER RADIATION
Do not stare into beam or view directly with optical instruments, class 3A laser product.
CAUTION Please heed the points listed below during servicing and inspection.
◎ Only use designated parts! Many of the electric and structural parts used in the set
have special safety properties. In most cases these prop-
The set's parts have specific safety properties (fire resis- erties are difficult to distinguish by sight, and using re-
tance, voltage resistance, etc.). For replacement parts, be placement parts with higher ratings (rated power and
sure to use parts which have the same properties. In par- withstand voltage) does not necessarily guarantee that
ticular, for the important safety parts that are marked z on safety performance will be preserved. Parts with safety
wiring diagrams and parts lists, be sure to use the desig- properties are indicated as shown below on the wiring dia-
nated parts. grams and parts lists is this service manual. Be sure to re-
place them with parts with the designated part number.
◎ Be sure to mount parts and arrange
the wires as they were originally! (1) Schematic diagrams ... Indicated by the z mark.
For safety reasons, some parts use tape, tubes or other in- (2) Parts lists ... Indicated by the z mark.
sulating materials, and some parts are mounted away from
Using parts other than the designated
the surface of printed circuit boards. Care is also taken with
parts could result in electric shock, fires or
the positions of the wires inside and clamps are used to
other dangerous situations.
keep wires away from heating and high voltage parts, so
be sure to set everything back as it was originally.
2
DN-S3700
DIMENSION
3
DN-S3700
DISASSEMBLY
• Disassemble in order of the arrow of the figure of following flow.
• In the case of the re-assembling, assemble it in order of the reverse of the following flow.
• In the case of the re-assembling, observe "attention of assembling" it.
SHIELD PLATE
4
DN-S3700
1. TOP CASE ASSY
Proceeding : TOP CASE ASSY
(1) Remove the screws and disconnect the FFC CABLE and connector wires.
SCREWS
SCREWS
SCREWS
TOP CASE ASSY
SCREWS
SCREWS
4P CONNECTOR WIRE ( CX043 ) 15P FFC CABLE ( CX151 )
7P FFC CABLE ( CX072 )
5
DN-S3700
(2) Pull out the KNOBs and remove the screws.
SCREWS
BRACKET
SCREWS
SCREWS
TOP SHIELD
PANEL 2 UNIT
PANEL 3 UNIT
SLIDE VR UNIT
FWD/BOTH UNIT
PANEL 1 UNIT
FADER KNOB
6
DN-S3700
2. MAIN UNIT
Proceeding : TOP CASE ASSY → SHILD PLATE → MAIN UNIT
(1) Disconnect the FFC CABLE and connector wires and remove the screws.
SCREWS
SHIELD PLATE
MAIN UNIT
7
DN-S3700
3. AC INPUT UNIT
Proceeding : TOP CASE ASSY → SHIELD PLATE → MAIN UNIT
→ CHASSIS STAY → AC INPUT UNIT
SCREWS
CHASSIS STAY
AC INPUT UNIT
Rear side
AUDIO UNIT
8
DN-S3700
(2) Disconnect the connector wire and remove the screws.
SCREWS
CORD BUSH
AC INPUT UNIT
2P CONNECTOR WIRE ( CY022 )
P.SW KNOB
9
DN-S3700
4. AUDIO UNIT
Proceeding : TOP CASE ASSY → SHIELD PLATE → MAIN UNIT
→ CHASSIS STAY → AUDIO UNIT
(1) Disconnect the FFC CABLE and connector wire and remove the screws.
SCREWS
9P CONNECTOR WIRE ( CY091 )
AUDIO UNIT
SCREWS
Rear Side
POWER UNIT
10
DN-S3700
5. POWER UNIT
Proceeding : TOP CASE ASSY → SHIELD PLATE → MAIN UNIT
→ CHASSIS STAY → POWER UNIT
(1) Disconnect the FFC CABLE and connector wire and remove the screws.
SCREWS
POWER UNIT
SCREWS
Rear Side
11
DN-S3700
6. MOTORDRIVE UNIT
Proceeding : TOP CASE ASSY → MOTORDRIVE UNIT
SCREWS
MOTORDRIVE UNIT
Rear Side
12
DN-S3700
7. CD MECHA UNIT
Proceeding : TOP CASE ASSY → CD MECHA UNIT
SCREWS
CD MECHA. UNIT
Rear Side
13
DN-S3700
8. CD IN UNIT
Proceeding : TOP CASE ASSY → CD IN UNIT
Rear side
SCREWS CD IN UNIT
14
DN-S3700
9. FRONT SUB PANEL
Proceeding : TOP CASE ASSY → FRONT SUB PANEL
Rear Side
SCREWS
BRACKET ( CD MASK )
CD MASK
SCREWS
FRONT SUB PANEL
15
DN-S3700
SERVICE MODE
Function summary
1. SERVICE MODE
(1) Top level of the service mode
6. Checking the rotation pulse detection of the JOG disc (JOG CHK)
(1) Platter jog disc rotation direction/rotation pulse number
(2) Turntable rotation direction/rotation pulse number
16
DN-S3700
1. SERVICE MODE
1.1. Top level of the service mode (Turning on the power in the service mode)
(1) Turn on the power while pressing the PARAMETERS knob and the button simultaneously.
The following appears on the VFD dot display section:
--Service Mode--
Function CHK
(2) When the PARAMETERS knob is turned clockwise, the display on the second row of the VFD dot display section
switches in the following order: "Function CHK" → "CD Drive CHK" → "SW Check" → "Panel CHK" → "JOG CHK" →
"PLATTER CHK".
The display switches in the opposite order when the PARAMETERS knob is turned counterclockwise.
(3) The displayed mode can be selected by pressing the PARAMETERS knob.
17
DN-S3700
2.3. Audio signal output (Audio OUT)
• The device's built-in 24 bit/44.1 kHz sampling frequency audio signals are played from ADSP.
(1) Turn the PARAMETERS knob to select "Audio OUT" from the “Function CHK” mode's top menu, then press the PA-
RAMETERS knob to set "Audio OUT" mode.
Information on the operations is displayed on the first row of the VFD dot display, information on the output signal on
the second row.
(2) Turn the PARAMETERS knob clockwise and display the signal to be output from q to o on the VFD dot display.
Press the PARAMETERS knob while the signal to be output is displayed to set it. The selected signal is output from
ADSP.
q 1kHz -6dBFS signals are output from the left and right channels.
Reference
1kHz -6dBFS
w 1kHz 0dBFS signals are output from the left and right channels.
Max Level
1kHz 0dBFS
e 20Hz -6dBFS signals are output from the left and right channels.
Freq. Chara.
20kHz -6dBFS
r 1kHz -6dBFS signals are output from the left and right channels.
Freq. Chara.
1kHz -6dBFS
t 20kHz -6dBFS signals are output from the left and right channels.
Freq. Chara.
20kHz -6dBFS
y 1kHz - ∞ dBFS signals are output from the left and right channels.
Infinity 0
u 1kHz -6dBFS signals are output from the left and right channels.
Reference
1kHz -6dBFS
(3) Press the button to return to the top level of the function check mode.
18
DN-S3700
2.5. USB device operation check (USB Test)
• Use this procedure to test data writing on the device connected to the USB-A connector.
(1) Turn the PARAMETERS knob to select "USB Test" from the “Function CHK” mode's top menu, then press the PARAM-
ETERS knob to set "USB Test" mode. The following appears on the VFD dot display section:
USB TEST
PUSH Param.
(2) The displayed mode can be executed by pressing the PARAMETERS knob. The following appearson the second row
of the VFD dot display section:
Now Testing
When the USB device is not connected:
Fail
(3) The test is completed, the following appears on the second row of the VFD dot display section:
When the process has completed normally:
Complete!
When the process has completed abnormally:
Fail
(4) Press the button to return to the top level of the function check mode.
When the keyboard is not connected, the following appears on the VFD dot display section (The the second row is
cleared):
KB Init Fail
(3) When a key on the keyboard is pressed, the key that was pressed is displayed on the second row of the VFD dot display
(A to Z, 0 to 9).
(4) Press the button to return to the top level of the function check mode.
19
DN-S3700
3. Checking the operations of the CD drive (CD Drive CHK)
(1) Turn the PARAMETERS knob to select "CD Drive CHK" from the service mode's top menu, then press the PARAME-
TERS knob to set the function check mode. The following appears on the VFD dot display section:
--Service Mode--
CD Drive CHK
(2) When the PARAMETERS knob is turned clockwise, the display on the second row of the VFD dot display section switch-
es in the following order: "Disc Type" → "Servo Data" → "Error Rate" → "PU Clean" → "Loader Clean" → "ErrorCode
CHK" → "Total Time" → "H/R1" → "H/R2". The display switches in the opposite order when the PARAMETERS knob is
turned counterclockwise.
(3) The displayed mode can be executed by pressing the PARAMETERS knob.
(4) Press the button to return to the top level of the service mode.
20
DN-S3700
3.4. Pickup movement (PU Clean)
• Move the pickup lens to any position.
(1) Turn the PARAMETERS knob to select "PU Clean" from the "CD Drive CHK" mode's top menu, then press the PA-
RAMETERS knob to set "PU Clean" mode. The following appears on the VFD dot display section:
PU Clean
PUSH BEND+&-
(2) Press the PITCH BEND button to move the pickup lens. The pickup lens stops moving when the PITCH BEND button
is released.( button: Direction of outer / button: Direction of inner)
(3) Press the button to return to the top level of the CD Drive check mode.
21
DN-S3700
3.7. Total running time display (Total Time)
(1) Turn the PARAMETERS knob to select "Total Time" from the "CD Drive CHK" mode's top menu, then press the PA-
RAMETERS knob to set "Total Time" mode. The following appears on the VFD dot display section:
Total Time
XXXXXh
(XXXXX:Total running time, Time [h])
(2) When the PARAMETERS knob is pushed, it switches to the Total Time deletion mode.
The following appears on the VFD dot display section:
Time Clear
Cancel
(3) When the PARAMETERS knob is turned, the display on the second row of the VFD dot display section switches in the
"OK" or "Cancel".
(4) Display "OK", then press the PARAMETERS knob to set. The total time is cleared and the display returns to as it was
in step (1).
(5) Display "Cancel", then press the PARAMETERS knob to set. The display returns to as it was in step (1).
(6) Press the button to return to the top level of the CD Drive check mode.
22
DN-S3700
3.10.Error code table
Error code Error contents
E100 Disc cannot be detected.
E101 Tracking offset cannot be adjusted.
E102 Focus offset cannot be adjusted.
E103 Focus rough gain cannot be adjusted.
E104 Focus servo does not turn on/spindle is faulty.
E105 Tracking servo does not turn on.
E106 Tracking rough gain cannot be adjusted.
E500 Slide error (inner circumference switch did not turn on within specified time).
E501 Search error (Slide error).
E502 Slide error (inner circumference switch did not turn on within specified time).
E800 Track skipped while data being stored in memory and retrying was conducted as
specified, but continuous data storage was not possible (forced link mode set).
23
DN-S3700
4. Checking the operations of the switches (SW Check)
(1) Turn the PARAMETERS knob to select "SW Check" from the service mode's top menu, then press the PARAMETERS
knob to set the "SW Check" mode.The following appears on the VFD dot display section.
--Service Mode--
SW Check
(2) All the VFD characters are lights.
The following appears on the VFD dot display section.
FNE123 T B<>
CPD BDR J-+
(3) When each switch is pushed
Brake → Turn off the "B" in the sixth place of second row.
Dump → Turn off the "D" in the seventh place of second row.
Reverse → Turn off the "R" in the eighth place of second row.
Echo/Loop → Turn off the "1" in the fourth place of first row.
Flanger → Turn off the "2" in the fifth place of first row.
Filter → Turn off the "3" in the sixth place of first row.
Eject → Turn off the "N" in the second place of second row.
PLAYLIST → Turn off the "D" in the third place of second row.
Fast Search → Turn off the "<" and ">" in the eleventh and twelfth place of first row.
BACK → Turn off the "B" in the tenth place of first row.
PITCH BEND → Turn off the "-" and " +" in the eleventh and twelfth place of second row.
TITLE → Turn off the "T" in the eighth place of first row.
FLIP → Turn off the "F" in the first place of first row.
EXIT_RELOOP → Turn off the "E" in the third place of first row.
CUE, PLAY → Turn off the "C" and "P" in the first and second place of second row.
PLATTER MODE → Turn off the "J" in the first and tenth place of second row.
A → Turn off the "(A" .
B → Turn off the "B)" .
MEMO → Turn off the "MEMO".
PITCH → Turn off the "PITCH".
TAP → Turn off the "BPM".
KEY ADJUST → Turn off the "KEY ADJ.".
CD → Turn off the "CD" .
USB → Turn off the "USB" .
MIDI → Turn off the "MIDI" .
TIME → Turn off the "T." .
DISPLAY → Turn off the "ELAPSED" .
AUTO → Turn off the "KB" .
EXIT → Turn off the "WFM".
A/B TRIM → Turn off the "AAC".
NEXT TRACK → Turn off the "MP3".
- (EFECT) → Turn off the "WAV".
+ (EFECT) → Turn off the "AIFF".
1 → Turn off the "1". (100's place of track no)
2 → Turn off the "2". (10's place of track no)
3 → Turn off the "3". (1's place of track no)
CLR1 → Turn off the "C1". (1's place of minutes' display)
CLR2 → Turn off the "C2". (1's place of seconds' display)
CLR3 → Turn off the "C3". (Frame display)
(4) Once all the switches have been pressed, The following appears on the VFD dot display section.
Complete!
Press Param
(5) Press the PARAMETERS knob return to the top layer in the service mode.
24
DN-S3700
5. Checking the operation of the panel (Panel CHK)
(1) Turn the PARAMETERS knob to select "Panel CHK" from the service mode's top menu, then press the PARAMETERS
knob to set the "Panel CHK" mode.
The following appears on the VFD dot display section:
P FC FP
E
FW< BT
Other displays/indicators
Track number display section : "***" (3-digit, pitch fader center value)
Pitch display section : "****" (4-digit, pitch slider status)
(2) Display of the status and results of the various control elements on the panel surface and external input from the rear side.
PARAMETERS knob → Displays the "P" for the first place of the first row of the VFD dot display section.
Toggles the display of the " ■ " for the second place of the first row of the VFD dot display
section between white and black each time the knob is pressed.
Displays the ">" (clockwise turn) for the fourth place of the first row or the "<" (counterclock-
wise turn) for the third place of the first row when the knob is turned, according to the direction
in which the knob is turned.
EFFECTS knob → Displays the "E" for the first place of the second row of the VFD dot display section.
Toggles the display of the " ■ " for the second place of the second row of the VFD dot display
section between white and black each time the knob is pressed.
Displays the ">" (clockwise turn) for the fourth place of the second row or the "<" (counter-
clockwise turn) for the third place of the second row when the knob is turned, according to the
direction in which the knob is turned.
Vinyl playback direction selector lever
→ When "FDW" is selected, "FW< BT" is displayed in the third row of the VFD dot display sec-
tion.
When "BOTH" is selected, "FW >BT" is displayed in the third row of the VFD dot display sec-
tion.
Pitch FADER → The pitch signal's AD conversion value is displayed on the pitch display section.
The center tap value is displayed in three digits on the track number display section.
FADER IN → Displays the "FC FP" for the sixth place of the first row of the VFD dot display section.
Displays " ■ " at the right of "FC FP" on the VFD dot display section while the "cue or play"
fade-in signal is being detected.
TAP button → When the TAP button is pressed, toggles between:
All LEDs lit + VFD fully lit → LED DIM lit (two LEDs on the sides of the VFD lit) + VFD fully off →
All LEDs off (for LEDs on the sides of the VFD, remaining two left and right lit) + VFD set to
normal display.
(3) Press button to return to the top level of the CD drive check mode.
25
DN-S3700
7. Platter check mode (PLATTER CHK)
• Displays the platter jog disc and turntable rotation pulse input number.
(1) Turn the PARAMETERS knob to select "PLATTER CHK" from the service mode's top menu, then press the PARAME-
TERS knob to set the "PLATTER CHK" mode.The following appears on the VFD dot display section:
33.3rpm Trq:h (PARAMETERS, FADER IN)
3336(3328,3344) (EFFECTS)
-0.08%(0.48%) (Vinyl playback direction selector)
(***** : Count value)
The first row of the VFD dot display section:
"33.33rpm" : Target rotation speed ← The TAP button and the rotation of the EFFECTS knob can be used to
change for target rotation speed (design verification.)
"Trq:H" : Torque ← 1, 2 and 3 buttons can be used to switch to H, M and L for torque (design verification.)
The second row of the VFD dot display section:
"3336" : Displays the current rotation speed. (4 digits with decimal point omitted)
"(3328,3344)" : Displays (minimum rotation speed, maximum rotation speed). Displays "mask time" for the several
seconds during which rotation is stabilizing.
The third row of the VFD dot display section:
"- 0.08%" : Displays the error with respect to the target rotation speed. ( ± with 2-digit value and 2-digit decimal)
"( 0.48%)" : Displays the range of fluctuation with respect to the target rotation speed. (2-digit value and 2-digit
decimal)
(2) Press the button to return to the top level of the CD drive check mode.
(1) Turn on the power while pressing the button, the button and the PARAMETERS knob simultaneously.
The following appears on the VFD dot display section:
VerUP MODE*
Push Cue
(2) Press the CUE button. The following appears on the VFD dot display section:
0100>>0111
Push Play
Complete!
PleasePowOFF
(6) Turn the power off and disconnect the USB device from the USB port.
26
DN-S3700
TROUBLE SHOOTING
FLOW CHART NO.1 (8U-110042:POWER UNIT)
The power cannot be turned on.
No
Is the fuse normal? See FLOW CHART NO.2 <The fuse blows out.>
Yes
Is normal state restored when once unplugged No Check if there is any leak or short-circuiting on the
power cord is plugged again after several seconds?
primary circuit component, and replace it if defective.
Yes (C903,C906,C907,C909,C914,C915,C918,C948,L901
No
Is the +12V line voltage normal? ,L902,T801)
Yes
Check each rectifying circuit of the secondary circuit
and replace it if defective.
Check the presence that the primary component Check the presence that the rectifying diode or
is leaking or shorted and replace it if defective. circuit is shorted in each rectifying circuit of
secondary side, and replace it if defective.
No
Is the +12V line voltage normal? Check if there is any leak or short-circuiting on the
Yes primary circuit component, and replace it if defective.
Check IC906 and the parts in surrounding, and replace (C903,C906,C907,C909,C914,C915,C918,C948,L901
it if defective. ,L902,T801)
No
Is the +5V line voltage normal? See FLOW CHART NO.3 <+3.3V is not outputted>
Yes
Check IC905 and the parts in surrounding, and replace
it if defective.
Is the voltage of +9V or more supplied to No Check D811 and the periphery circuit, and replace it
Corrector terminal of TR813? if defective.
Yes
Check TR813 and the periphery circuit, and replace it
if defective.
Is the voltage of -9V or less supplied to No Check D810 and the periphery circuit, and replace it
Corrector terminal of TR814? if defective.
Yes
Check TR814 and the periphery circuit, and replace it
if defective.
27
DN-S3700
FLOW CHART NO.7 (8U-310011:MAIN UNIT)
+12V is not outputted.
Check whether parts C426 and C427 are linked,
No
Is 3.3V voltage supplied to 7pins(PVCC) of IC403? short-circuited or open and whether FB402 is open,
Yes and replace any faulty parts.
Check IC403 and the periphery circuit, and replace
it if defective.
Yes
Is 30V voltage supplied to 40pins(HV1) of FL901? No Check ZD901 and the periphery circuit, and service
it if defective.
Yes
Are the filament voltage supplied between 1pin No
and 49pin of the fluorescent display tube (FL901)? Check the F1/F2 line and service it if defective.
Yes
No
Is voltage supplied to 34pins(RESET) of FL901? Check the RESET line and service it if defective.
Yes
Replace the fluorescent display tube(FL901).
Are the contact point and the installation state of the No Re-install the switches correctly or replace
tact switche normal? the poor switch.
Yes
No Check the TR701~708and their periphery, and service
Does LED light correctly ?
it if detective.
Yes
When pressing each switches, do the voltage of No Check the switches and their periphery, and service
each pin of IC702 increase? it if detective.
Yes
Replace IC702(IC802).
The USB memory in which test signal (MP3,WAV) No Check the input signal from CY112 to IC802 and their
of 1kHz/0dB is written is prepared. periphery, and service it if detective.When the
With USB memory playback mode, with the test signal input signal is correct, IC802 or IC803 is replaced.
of 1kHz/0dB it repeats between B from A and puts in (Note:For the IC802 OUT signal,
playback state. the right and left are inversely output internally.)
Are the audio signals outputted to 11,12pin(Rch) and
17,18pin(Lch) of IC802?
Check periphery circuit from 14pin and 15pin to
Yes IC804 of IC802, and service it if defective.
Are the audio signals outputted to 7pin(Rch) and No When the periphery circuit is correct, IC804 is
1pin(Lch) of IC804? replaced.
Yes
Is the TR807 collector L (-9V) when muting No Check TR807 and the periphery circuit, and service it if
is canceled? defective.
Yes
Check periphery circuit from 7pin and 1pin to
JK801 of IC804, and replace it if defective.
28
DN-S3700
BLOCK DIAGRAM
S3700 block Diagram
Main
Main +12V
+5V +5V
Audio
Audio
+5VA
1.5V Reg. Xtal CX112 CY112 +3.3VA 㫧9VA
+1.5V +3.3V 16.9344MH䌺 Audio
CX222 LPF& RCA OUT L
MUTE
Audio JK801
11pin FFC
11pin FFC
DAC16.9M DAC LPF& RCA Audio
5ch Motor
22pinFFC
XI PCM OUT R
driver DABCK / DALRCK / DATA 1791
BD7956 EFS CD SERVO DSP +5V
BU9547KV D.Audio
(ROHM) SPDIF SPDIF
CLKIN RCA OUT JK802
䋨ROHM䋩 Drive
CD MECHA Audio DSP
Audio( Serial )
TMS320DA710GDH300 +5VA
BUSY,SENS
䊶Audio Trick-play 32bit 㫧9VA +5V
Command
8MWx16bit +3.3VA
Sub Code
䊶Audio EFX
24pinFFC
SDRAM
8MWx16bit 9P-KR CY091
Reset
䊶MP3 DECx2 SDRAM
(TI)
Power AC
ACINPUT
INPUT
Power
Reset
9P KR-DA
UHPI
CX241 CW091
8 2 3 3
+3.3V CX071 CW071 㫧9VA +5V AC IN
+1.2V +3.3V
7P KR-DA
+1.2V +12V
7P KRs
EXTAL +12V
MUTE +5V CX021
2P VH
ADSP_RST 1.2V +5V DCDC
+3.3V
+1.2V DC-DC
UHPI control +3.3V
+3.3V
Reg AC SW
D-Sync
RJ45 CX081
㫧9V
㫧9VA Reg SW
+5V RST CPU CUE / PLAY Mini TRANS
IC Jack JK401 㫧8V
SH7263 +5V 㫧8V 2P VH CY022
USB_EN / USB_FLG Power SW Reg
䋨RENESAS䋩
BD2041
USB 2 USB +40V
X'tal 48MH䌺 USB SW HV( +40V 䋩
CLK 2 A CX041 Reg
TS3USB221
2P VH CX022
PS2PWR 2 USB
Flash ROM UART / other B CX045 F1, F2( AC3.8V 䋩
2MB㬍16Bit Sub CPU RST
JOG A/B, TT A/B
PS2PWR
SPI / FL_RST
18pinFFC
18pinFFC
SDRAM
16MB㬍16Bit
16bit BUS
+5V
STROBE LED
CX151 CX181
CY181
Reset
15pinFFC CX072 7pinFFC
PANEL3
PANEL3
4 PS2/ 2 MINI
Motor Drive IF DIN
CW033
Panel
Panel 11 CX042 SH7125 SPI
CW042
SW x2 +3.3V
CX034
1
3P-KRs
3P-DS
+5V HV
4P_DS
4P-KR
Character
CW034
CX033
SW x11 3 +3.3V
25㬍100dot
CD
CDIN
INLED
LED 3 F1, F2
㫧8V
S/P Driver P/S buff CX121
CW043
C䌘043
CY143
14P-KRs
14P-DS
4P-KRs
TB62725BF
S/P Driver 74LV165
4P-DS
LED x3
12P-PH
㫧8V
TB62725BF
LV14
12pinPH
4
CW143
SLIDE_VR
SLIDE_VR
LED x46 SW x31 ENC x2
UNIT
UNIT CX141 14pinEH
FWD/BOTH
FWD/BOTH Motor UNIT
Select Tr +5V
Select FG3700 CY141
4P KRs
C䌘042
C䌗031
C䌗042
3P-DS
4P-DS
3P-KRs
14pinEH
C䌘031
SW 3-8 DEC
x1 SN74LV138 㫧8V
Motor Drive MOTOR DRIVE
UNIT
29
DN-S3700
LEVEL DIAGRAM
30
DN-S3700
SEMICONDUCTORS
Only major semiconductors are shown, general semiconductors etc. are omitted to list.
The semiconductor which described a detailed drawing in a schematic diagram are omitted to list.
1. IC’s
D710E001ZDH300 (IC501)
R/W McASP1
256 ROM Page2
256K Bytes 32 6 Serializers
Program
I/O INT Fetch Program/Data
256 ROM Page3 32 McASP2
256K Bytes 2 Serializers
256
32 + DIT
Peripheral Configuration Bus
Program CSP 32 32
32 SPI1
Cache 256
32K Bytes PMP DMP
32 SPI0
32 32
32 I2C0
High-Performance
32
Crossbar Switch
32 I2C1
32 32 32 32
32 RTI
31
DN-S3700
D710E001ZDH300 Pin Function
32
DN-S3700
D710E001ZDH300 Terminal Function
Pin No. Pin Name Symbol I/O DET Ext Ini Res Function
1 A1 D_GND - - - - - GND
2 A2 DVDH I - - - - I/O supply (+3.3V)
3 A3 AFSX0 I/O - - - - DALRCK
4 A4 ACLKX0 I/O - McASPO transmit bit clock
5 A5 ACLKR0 - - Pd - -
6 A6 AXR0[14] I/O - - - - BSPDIF
7 A7 D_GND - - - - - GND
8 A8 AXR0[11] - - Pd - -
9 A9 AXR0[9] - - Pd - -
10 A10 D_GND - - - - - GND
11 A11 AEMXA1 - - Pd - -
12 A12 AXR0[4] - - Pd - -
13 A13 AXR0[2] - - Pd - -
14 A14 AXR0[0] I/O - - - - DATA_A
15 A15 DVDH I - - - - I/O supply (+3.3V)
16 A16 D_GND - - - - - GND
17 B1 DVDH I - - - - I/O supply (+3.3V)
18 B2 /UHPI_HBE3 I/O - Pu - - Byte enable signal (D31~D24)
19 B3 AD384FS - - Pd - -
20 B4 AFSR0 - - Pd - -
21 B5 AXR0[15] I/O - - - - ASPDIF
22 B6 ADDATA - - Pd - -
23 B7 AXR0[12] - - Pd - -
24 B8 AXR0[10] - - Pd - -
25 B9 AEMXA3 - - Pd - -
26 B10 AEMXA2 - - Pd - -
27 B11 AEMXA0 - - Pd - -
28 B12 AXR0[3] - - Pd
29 B13 AXR0[1] I/O - - - - DATA_B
30 B14 SPI0_SOMI I/O - I2C Serial data
31 B15 SPI0_SIMO - - Pd - - Not used
32 B16 DVDH I - - - - I/O supply (+3.3V)
33 C1 AMUTE0 - - Pd - -
34 C2 384FS - - Pd - - Not used
35 C3 - Not used
36 C4 /UHPI_HBE2 - Byte enable signal (D23~D16)
37 C5 DSPHBE - Byte enable signal (D15~D8)
38 C6 DSPHBE - Byte enable signal (D7~D0)
39 C7 DSPHWE I - - - - Write enable signal
40 C8 710HCS I - - - - Chip select signal
41 C9 /UHPI_HAS I - Pu - - Address strobe signal
42 C10 DSPHCTL1 I - - - - Control inputs select access mode (1)
43 C11 AFSX2 - - Pd - -
44 C12 AFSR2 - - Pd - -
45 C13 ACLKR2 - - Pd - -
46 C14 AHCLKR2 - - Pd - -
47 C15 /SPI0_SCS I/O - Pd - - SPI0 slave chip select
48 C16 SPI0_CLK I/O - I2C serial clock
49 D1 AHCLKX1 - - Pd - -
50 D2 AMUTE1 - - Pd - -
51 D3 - Not used
52 D4 DVDH I - - - - I/O supply (+3.3V)
53 D5 DVDH I - - - - I/O supply (+3.3V)
54 D6 /UHPI_HRDY O - - - - Host ready signal
55 D7 DSPHRD I - - - - Read strobe signal
56 D8 DSPRW I - - - - Read/not write signal
57 D9 DSPHCTL0 I - - - - Control input select access mode (0)
58 D10 AMUTE2 O - DSP interrupt
59 D11 ACLKX2 - - Pd - - McASP2 transmit bit clock
60 D12 DVDH I - - - - I/O supply (+3.3V)
61 D13 DVDH I - - - - I/O supply (+3.3V)
62 D14 EM_WAIT I - Pu - - Not used (Asynchronous wait input)
63 D15 AFMOE O - Pd - - Not used (External memory out put enable)
64 D16 /SPI0_/ENA I/O - Pd - - Not used
65 E1 ADBCK - - Pd - -
33
DN-S3700
Pin No. Pin Name Symbol I/O DET Ext Ini Res Function
66 E2 ACLKX1 - - Pd McASP1 transmit bit clock
67 E3 - - - - - Not used
68 E4 DVDH I - - - - I/O supply (+3.3V)
69 E5 D_GND - - - - - GND
70 E6 CVDL I - - - - Core supply (+1.2V)
71 E7 CVDL I - - - - Core supply (+1.2V)
72 E8 CVDL I - - - - Core supply (+1.2V)
73 E9 CVDL I - - - - Core supply (+1.2V)
74 E10 CVDL I - - - - Core supply (+1.2V)
75 E11 CVDL I - - - - Core supply (+1.2V)
76 E12 D_GND - - - - - GND
77 E13 DVDH I - - - - I/O supply (+3.3V)
78 E14 SHDB8 I/O - - - - CPU bus data 8
79 E15 AFMCE - - Pd - - Not used (Asynchronous external memory select)
80 E16 - - - - - - Not used (Asynchronous external memory read write)
81 F1 ADLRCK - - Pd - -
82 F2 AFSX1 - - Pd - -
83 F3 - - - - - Not used
84 F4 - - - - - Not used
85 F5 D_GND - - - - - GND
86 F6 D_GND - - - - - GND
87 F7 D_GND - - - - - GND
88 F8 D_GND - - - - - GND
89 F9 D_GND - - - - - GND
90 F10 D_GND - - - - - GND
91 F11 D_GND - - - - - GND
92 F12 D_GND - - - - - GND
93 F13 SHDB10 I/O - - - - CPU bus data 10
94 F14 SHDB9 I/O - - - - CPU bus data 9
95 F15 ASDCE O - - - - External memory chip select
96 F16 ASDRAS O - - - - Sync memory row address strobe signal
97 G1 D_GND - - - - - GND
98 G2 710RST I - - - - Reset
99 G3 - - - - - Not used
100 G4 - - - - - Not used
101 G5 CVDL I - - - - Core supply (+1.2V)
102 G6 D_GND - - - - - GND
103 G7 D_GND - - - - - GND
104 G8 D_GND - - - - - GND
105 G9 D_GND - - - - - GND
106 G10 D_GND - - - - - GND
107 G11 D_GND - - - - - GND
108 G12 CVDL I - - - - Core supply (+1.2V)
109 G13 SHDB12 I/O - - - - CPU bus data 12
110 G14 SHDB11 I/O - - - - CPU bus data 11
111 G15 AEMB0 O - - - - External memory bank address 0
112 G16 D_GND - - - - - GND
113 H1 DSPHWIL I/O - - - - High or low of half-word
114 H2 DSP16.9M I - - - - Clock input
115 H3 D_GND - - - - - GND
116 H4 - - - - - Not used
117 H5 CVDL I - - - - Core supply (+1.2V)
118 H6 D_GND - - - - - GND
119 H7 D_GND - - - - - GND
120 H8 D_GND - - - - - GND
121 H9 D_GND - - - - - GND
122 H10 D_GND - - - - - GND
123 H11 D_GND - - - - - GND
124 H12 CVDL I - - - - Core supply (+1.2V)
125 H13 SHDB14 I/O - - - - CPU bus data 14
126 H14 SHDB13 I/O - - - - CPU bus data 13
127 H15 AEMA10 O - - - - External memory bus address 10
128 H16 AEMB1 O - - - - External memory bank address 1
129 J1 D_GND - - - - - GND
130 J2 D_GND - - - - - GND
131 J3 O - - - - Not used
132 J4 CVDL I - - - - Core supply (+1.2V)
34
DN-S3700
Pin No. Pin Name Symbol I/O DET Ext Ini Res Function
133 J5 CVDL I - - - - Core supply (+1.2V)
134 J6 D_GND - - - - - GND
135 J7 D_GND - - - - - GND
136 J8 D_GND - - - - - GND
137 J9 D_GND - - - - - GND
138 J10 D_GND - - - - - GND
139 J11 D_GND - - - - - GND
140 J12 CVDL I - Core supply (+1.2V)
141 J13 SHDB15 I/O - - - - CPU bus data 15
142 J14 DVDH I - - - - I/O supply (+3.3V)
143 J15 AEMA1 O - - - - External memory bus address 1
144 J16 AEMA0 O - - - - External memory bus address 0
145 K1 D_GND - - - - - GND
146 K2 PLLHV I - - - - PLL supply (3.3V)
147 K3 TMS_A I - - - - Test mode select signal (JTAG)
148 K4 /TRST_A I - - - - Test reset signal (JTAG)
149 K5 CVDL I - - - - Core supply (+1.2V)
150 K6 D_GND - - - - - GND
151 K7 D_GND - - - - - GND
152 K8 D_GND - - - - - GND
153 K9 D_GND - - - - - GND
154 K10 D_GND - - - - - GND
155 K11 D_GND - - - - - GND
156 K12 CVDL I - - - - Core supply (+1.2V)
157 K13 SHDB0 I/O - - - - CPU bus data 0
158 K14 SHDB1 I/O - - - - CPU bus data 1
159 K15 AEMA2 O - - - - External memory bus address 2
160 K16 D_GND - - - - - GND
161 L1 TDI_A I - - - - Test data input (JTAG)
162 L2 - - - - - Not used
163 L3 - - - - - Not used
164 L4 - - - - - Not used
165 L5 D_GND - - - - - GND
166 L6 D_GND - - - - - GND
167 L7 D_GND - - - - - GND
168 L8 D_GND - - - - - GND
169 L9 D_GND - - - - - GND
170 L10 D_GND - - - - - GND
171 L11 D_GND - - - - - GND
172 L12 D_GND - - - - - GND
173 L13 SHDB3 I/O - - - - CPU bus data 3
174 L14 SHDB4 I/O - - - - CPU bus data 4
175 L15 AEMA4 O - - - - External memory bus address 4
176 L16 AEMA3 O - - - - External memory bus address 3
177 M1 /EMU0 I/O - - - - Emulation pin 0 (JTAG)
178 M2 TDO_A OZ - - - - Test data out (JTAG)
179 M3 - - - - - Not used
180 M4 DVDH I - - - - I/O supply (+3.3V)
181 M5 D_GND - - - - - GND
182 M6 CVDL I - - - - Core supply (+1.2V)
183 M7 CVDL I - - - - Core supply (+1.2V)
184 M8 CVDL I - - - - Core supply (+1.2V)
185 M9 CVDL I - - - - Core supply (+1.2V)
186 M10 CVDL I - - - - Core supply (+1.2V)
187 M11 CVDL I - - - - Core supply (+1.2V)
188 M12 D_GND - - - - - GND
189 M13 DVDH I - - - - I/O supply (+3.3V)
190 M14 SHDB2 I/O - - - - CPU bus data 2
191 M15 AEMA6 O - - - - External memory bus address 6
192 M16 AEMA5 O - - - - External memory bus address 5
193 N1 /EMU1 I/O - - - - Emulation pin 1
194 N2 - - - - - Not used
195 N3 - - - - - Not used
196 N4 AEMD22 I/O - - - - External memory bus data 22
197 N5 DVDH I - - - - I/O supply (+3.3V)
198 N6 AEMD18 I/O - - - - External memory bus data 18
199 N7 AEMD16 I/O - - - - External memory bus data 16
35
DN-S3700
Pin No. Pin Name Symbol I/O DET Ext Ini Res Function
200 N8 AEMD30 I/O - - - - External memory bus data 30
201 N9 AEMD29 I/O - - - - External memory bus data 29
202 N10 AEMD27 I/O - - - - External memory bus data 27
203 N11 AEMD25 I/O - - - - External memory bus data 25
204 N12 DVDH I - - - - I/O supply (+3.3V)
205 N13 SHDB5 I/O - - - - CPU bus data 5
206 N14 SHDB6 I/O - - - - CPU bus data 6
207 N15 AEMA8 O - - - - External memory bus address 8
208 N16 AEMA7 O - - - - External memory bus address 7
209 P1 TCK_A I - - - - Test clock (JTAG)
210 P2 - - - - - Not used
211 P3 AEMD21 I/O - - - - External memory bus data 21
212 P4 AEMD20 I/O - - - - External memory bus data 20
213 P5 AEMD19 I/O - - - - External memory bus data 19
214 P6 AEMD17 I/O - - - - External memory bus data 17
215 P7 AEMD31 I/O - - - - External memory bus data 31
216 P8 DVDH I - - - - I/O supply (+3.3V)
217 P9 AEMD28 I/O - - - - External memory bus data 28
218 P10 AEMD26 I/O - - - - External memory bus data 26
219 P11 AEMD24 I/O - - - - External memory bus data 24
220 P12 AEMA12 O - - - - External memory bus address 12
221 P13 ASDQM2 O - - - - External memory byte enable signal
222 P14 SHDB7 I/O - - - - CPU bus data 7
223 P15 AEMA11 O - - - - External memory bus address 11
224 P16 AEMA9 O - - - - External memory bus address 9
225 R1 DVDH I - - - - I/O supply (+3.3V)
226 R2 AEMD23 I/O - - - - External memory bus data 23
227 R3 ASDCAS O - - - - Sync memory column address strobe signal
228 R4 ASDQM0 - - - - External memory byte enable signal
229 R5 AEMD6 I/O - - - - External memory bus data 6
230 R6 AEMD4 I/O - - - - External memory bus data 4
231 R7 AEMD2 I/O - - - - External memory bus data 2
232 R8 AEMD1 I/O - - - - External memory bus data 1
233 R9 AEMD15 I/O - - - - External memory bus data 15
234 R10 AEMD13 I/O - - - - External memory bus data 13
235 R11 AEMD12 I/O - - - - External memory bus data 12
236 R12 AEMD10 I/O - - - - External memory bus data 10
237 R13 AEMD8 I/O - - - - External memory bus data 8
238 R14 MERCK 0 - External memory clock out
239 R15 ASDQM3 0 - - - - External memory byte enable signal
240 R16 DVDH I - - - - I/O supply (+3.3V)
241 T1 D_GND - - - - - GND
242 T2 DVDH I - - - - I/O supply (+3.3V)
243 T3 ASDWE O - - - - External memory write enable signal
244 T4 AEMD7 I/O - - - - External memory bus data 7
245 T5 AEMD5 I/O - - - - External memory bus data 5
246 T6 AEMD3 I/O - - - - External memory bus data 3
247 T7 D_GND - - - - - GND
248 T8 AEMD0 I/O - - - - External memory bus data 0
249 T9 AEMD14 I/O - - - - External memory bus data 14
250 T10 D_GND - - - - - GND
251 T11 AEMD11 I/O - - - - External memory bus data 11
252 T12 AEMD9 I/O - - - - External memory bus data 9
253 T13 ASDQM1 - External memory byte enable signal
254 T14 ASDCKE O - - - - External memory clock enable signal
255 T15 DVDH I - - - - I/O supply (+3.3V)
256 T16 D_GND - - - - - GND
36
DN-S3700
R5S72630P200FP (IC104)
.
37
DN-S3700
R5S72630P200FP Block Diagram
38
DN-S3700
R5S72630P200FP Terminal Function
Pin
Pin Name Symble I/O Function
No.
1 PC10/nRASU/nBACK/AUDATA0 MUTE O General-purpose port ADC MUTE output : Mute On = L,
2 PC9/nCASL SHCAS O nCASL SDRAM /CAS
3 PC8/nRASL SHRAS O nRASL SDRAM /RAS
4 VCC VCC P Power supply for in Digital +1.2V
OPEN (Unused: Monitor output for examination) :
5 PC7/nWE3/DQMUU/nAH/nICIOWR TP1 O General-purpose port
ES → TC change point
6 VSS VSS G - Digital GND
7 PVSS PVSS G GND for I/O Digital GND
8 PC6/nWE2/DQMUL/nICIORD - O General-purpose port OPEN (Unused : General-purpose Lo output setting)
9 PVCC PVCC P Power supply for I/O Digital +3.3V
10 PC5/nWE1/DQMLU/nWR DQMLU O DQMLU SDRAM DQMU
11 nCS0 CS0 O CS0 :FLASH ROM FLASH /E
FLASH_nG + ADSP_HDS1 :
12 nRD SHRD O nRD
ADSP connection addition
SDRAM DQML + ADSP_HDS2 : ADSP connection addition
13 PC4/nWE0/DQMLL SHWE O nWE0/DQMLL
Access switching function ⇒ nWE0
14 PC3/nCS3 CS3 O nCS3 SDRAM /CS
15 PC2/nCS2 PC2 O General-purpose port OPEN (Unused : General-purpose Lo output setting
16 VCC VCC P Power supply for in Digital +1.2V
17 PC0/A0/nCS7/nAUDSYNC ADSPRST O General-purpose port ADSP reset signal output : Active = L (Pull Down)
18 VSS VSS G - Digital GND
19 PVSS PVSS G GND for I/O Digital GND
SDRAM/FLASH A0 +ADSP_HHWIL :
20 PC1/A1 SHA1 O A1
ADSP connection addition
21 PVCC PVCC P Power supply for I/O Digital +3.3V
SDRAM/FLASH A1 +ADSP_HCNTL0 :
22 A2 SHA2 O A2
ADSP connection addition
SDRAM/FLASH A2 +ADSP_HCNTL1 :
23 A3 SHA3 O A3
ADSP connection addition
24 A4 SHA4 O A4 SDRAM/FLASH A3
25 A5 SHA5 O A5 SDRAM/FLASH A4
26 A6 SHA6 O A6 SDRAM/FLASH A5
27 A7 SHA7 O A7 SDRAM/FLASH A6
28 A8 SHA8 O A8 SDRAM/FLASH A7
29 PVCC PVCC P Power supply for I/O Digital +3.3V
30 A9 SHA9 O A9 SDRAM/FLASH A8
31 PVSS PVSS G GND for I/O Digital GND
32 VSS VSS G Digital GND
33 A10 SHA10 O A10 SDRAM/FLASH A9
34 VCC VCC P Power supply for I/O Digital +1.2V
35 A11 SHA11 O A11 SDRAM/FLASH A10
36 A12 SHA12 O A12 SDRAM/FLASH A11
37 A13 SHA13 O A13 FLASH A12
38 A14 SHA14 O A14 FLASH A13
39 A15 SHA15 O A15 FLASH A14
40 A16 SHA16 O A16 FLASH A15
41 PVSS PVSS G GND for I/O Digital GND
42 A17 SHA17 O A17 FLASH A16
43 PVCC PVCC P Power supply for I/O Digital +3.3V
44 A18 SHA18 O A18 FLASH A17
45 A19 SHA19 O A19 FLASH A18
46 A20 SHA20 O A20 FLASH A19
Deck1 FL shift clock output :
47 PE2/A21/SCK0 - O General-purpose port
(Unused : General-purpose Lo output setting
Deck1 FL chip selection output :
48 PE3/A22/SCK1 - O General-purpose port
(Unused : General-purpose Lo output setting
49 PE0/nBS/RXD0/nADTRG USB_EN O General-purpose port USB VBUS ENABLE signal output (L : ENABLE)
50 CKIO CKIO O CKIO SDRAM CLK
51 VCC VCC P Power supply for in Digital +1.2V
52 VSS VSS G Digital GND
53 PVSS PVSS G GND for I/O Digital GND
54 PVCC PVCC P Power supply for I/O Digital +3.3V
55 XTAL XTAL O Oscillation output Unused: OPEN
56 EXTAL EXTAL I EXTAL 16.9344MHz input
57 NMI NMI I NMI Unused: 3.3k pull-up
58 PLLVSS PLLVSS G Digital GND
59 nRES /RES I /RES JTAG I/F connector ⑬ H pin
60 PLLVCC PLLVCC P 1.2V after LC
Emulator function ON/
61 nASEMD /ASEMD I JTAG I/F connector ③ H pin
OFF
62 PE8/nCE2A/IRQ4/SCK2 SUB_INT I IRQ4 Sub CPU INT Terminal
FL DATA output :
63 PE1/nCS4/nMRES/TXD0 DA1 O General-purpose port
(Unused : General-purpose Lo output setting
39
DN-S3700
Pin
Pin Name Symble I/O Function
No.
General-purpose port USB VBUS over current detection signal input
64 PE4/A23/IRQ0/RXD1/DREQ0 USB_/FLG I
(Interrupt port) (IRQ0:usable)(Normal=H, detect=L)
65 PVSS PVSS G GND for I/O Digital GND
66 PE5/A24/IRQ1/TXD1/DACK0 ADSP_nHINT I IRQ1 ADSP bus IRQ
67 PVCC PVCC P Power supply for I/O Digital +3.3V
68 PE6/A25/IRQ2/RXD2/DREQ1 RX I SCIF Rx Memo Terminal (Memo Link Rx)
69 PE7/nFRAME/IRQ3/TXD2/DACK1 TX O SCIF Tx Memo Terminal (Memo Link Tx)
70 PE9/nCS5/nCE1A/IRQ5/SCK3 SUB_SCK O SCK3 Sub CPU cereal SCK
USB_SW :
71 PE10/nCE2B/IRQ6/TEND0 USB_HnD O General-purpose port
USB HOST/Device switching SW(H=Host, L=Device)
72 PE11/nCS6/nCE1B/IRQ7/TEND1 ADSP_nCS O nCS6 ADSP chip selec (+ byte enable)
73 PE12/RXD3 SUB_MISO I RXD3 Sub CPU cereal MISO
74 VCC VCC P Power supply for in Digital +1.2V
75 PC14/nWAIT ADSP_nRDY I nWAIT ADSP bus standby demand
76 VSS VSS G Digital GND
77 PVSS PVSS G GND for I/O Digital GND
78 RTC_X1 RTC_X1 I Empty pin processing Unused: GND
79 RTC_X2 RTC_X2 O Empty pin processing Unused: OPEN
80 PVCC PVCC P Power supply for I/O Digital +3.3V
81 PE13/TXD3 SUB_MOSI O TXD3 Sub CPU cereal MISO
82 PE14/nCS1/nCTS3 SUB_RST O General-purpose port Sub CPU reset
Sub CPU operation mode setting :
83 PE15/nIOIS16/nRTS3 SUB_MD1 O General-purpose port
For Sub CPU(SH7124) onboard writing
84 PVSS PVSS G GND for I/O Digital GND
Serbo DSP Reset signal output(Active=L)
85 PB8/CRXD0/CRXD0/CRXD1 CD_RST O General-purpose port
Pull Down
86 PB9/CTXD0/CTXD0/CTXD1 SUBDATA I General-purpose port Serbo DSP subcord data input
Sub CPU Flash enable :
87 PB10/CRXD1/IERXD SUB_FWE O General-purpose port
For Sub CPU(SH7124) onboard writing
88 PB11/CTXD1/IETXD SUBCK O General-purpose port Serbo DSP subcord clock output
89 VCC VCC P Power supply for in Digital +1.2V
Mode setting
90 MD MD I Pull-down in GND
(1:32bit/0:16bit)
91 VSS VSS G Digital GND
92 PVSS PVSS G GND for I/O Digital GND
93 USB_X1 USB_X1 Clock generation for USB 48MHz X 'tal connection
94 USB_X2 USB_X2 ↑ ↑
95 PVCC PVCC P Power supply for I/O Digital +3.3V
96 MD_CLK1 MD_CLK1 I Clock selection setting
97 MD_CLK0 MD_CLK0 I ↑
98 USBDPVSS USBDPVSS G Digital GND for drive Digital GND
Digital power supply for
99 USBDPVCC USBDPVCC P Digital +3.3V
driver
100 DM DM I/O D-terminal USB connector connection
101 DP DP I/O D + terminal ↑
102 VBUS VBUS I VBUS detection terminal Terminal VBUS connecting directly through 56Ω
Analog power supply
103 USBAVCC USBAVCC P Analogue +1.2V
for in driver
104 USBAVSS USBAVSS G Analog GND for in driver Analog GND
Reference resistance
105 REFRIN REFRIN I Connects it GND by 5.6kΩ ± 1% resistance
connection
106 USBAPVSS USBAPVSS G Analog GND for driver Analog GND
Analog power supply
107 USBAPVCC USBAPVCC P Analogue +3.3V
for driver
Digital power supply
108 USBDVCC USBDVCC P Digital +1.2V
for in driver
109 USBDVSS USBDVSS G Digital GND for in driver Digital GND
110 PA0/AN0 PITCH1 I ADC input Deck1 Pitch input
111 PA1/AN1 CENT1 I ADC input Deck1 Center input
112 PA2/AN2 AN2 I ADC input GND
113 PA3/AN3 AN3 I ADC input GND
114 AVCC AVCC P Power supply for ADC/DAC After LC, +3.3V is supplied
115 PA4/AN4 AN4 I ADC input GND
116 AVREF AVREF I Conversion standard voltage 114pin and connection
Serbo DSPTEST1 input
117 PA5/AN5 TEST1 I ADC input
(automatic adjusting abnormal condition=H)
118 PA6/AN6/DA0 LOADING O DAC output CD Loading Motor DAC output (default:80h)
Unused: GND connecting directly and input setting :
119 PA7/AN7/DA1 - I ADC input
General-purpose port: LED green( Hi = On )
120 AVSS AVSS G GND for ADC/DAC Analog GND
121 PVSS PVSS G GND for I/O Digital GND
122 PB12/nWDTOVF/nIRQOUT/nUBCTRG/AUDCK /WDTOVF O WDT output(L active) OPEN
123 PVCC PVCC P Power supply for I/O Digital +3.3V
Matrix for three-phase clock output :
124 PF29/SSIDATA3 SC0 O General-purpose port
CMT CH1 function is used. (CMT CH0 is used with the system. )
40
DN-S3700
Pin
Pin Name Symble I/O Function
No.
Matrix for three-phase clock output :
125 PF28/SSIWS3 SC1 O General-purpose port
CMT CH1 function is used. (CMT CH0 is used with the system. )
Matrix for three-phase clock output :
126 PF27/SSISCK3 SC2 O General-purpose port
CMT CH1 function is used. (CMT CH0 is used with the system. )
Digital +1.2V :
127 VCC VCC P Power supply for in
CMT CH1 function is used. (CMT CH0 is used with the system. )
Matrix for cereal clock output :
128 PF30/AUDIO_CLK SCK O General-purpose port
CMT CH1 function is used. (CMT CH0 is used with the system. )
Digital GND :
129 VSS VSS G
CMT CH1 function is used. (CMT CH0 is used with the system. )
Digital GND :
130 PVSS PVSS G GND for I/O
CMT CH1 function is used. (CMT CH0 is used with the system. )
GND :
131 AUDIO_X1 AUDIO_X1 I Not used
CMT CH1 function is used. (CMT CH0 is used with the system. )
OPEN :
132 AUDIO_X2 AUDIO_X2 O Not used
CMT CH1 function is used. (CMT CH0 is used with the system. )
Digital +3.3V :
133 PVCC PVCC P Power supply for I/O
CMT CH1 function is used. (CMT CH0 is used with the system. )
The BLINK output is generated with CMT :
134 PF26/SSIDATA2 BLINK O General-purpose port
CMT CH1 function is used. (CMT CH0 is used with the system. )
SW/ENC data input :
135 PF25/SSIW2 KEYDATA I General-purpose port
CMT CH1 function is used. (CMT CH0 is used with the system. )
LED data output :
136 PF24/SSISCK2 LEDDATA O General-purpose port
CMT CH1 function is used. (CMT CH0 is used with the system. )
137 PF18/SSISCK0/LCD_CL2 CD_DCK I Audio BCK CD-Audio DCK input
138 PF19/SSIWS0/LCD_M_DISP CD_LRCK I Audio word clock CD-Audio LRCK input
139 PF20/SSIDATA0/LCD_FLM CD_DATA I Audio data CD-Audio DATA input
140 PF21/SSISCK1/LCD_CLK SSISCLK1 I Audio BCK 137pin connection(CD-Audio DCK input)
141 VCC VCC P Power supply for in Digital +1.2V
142 PF22/SSIWS1/LCD_VCPWC/AUDATA2 SSIWS1 I Audio word clock 138pin connection(CD-Audio LRCK input)
143 VSS VSS G Digital GND
144 PVSS PVSS G GND for I/O Digital GND
145 PF23/SSIDATA1/LCD_VEPWC/AUDATA3 SUBSYQ I Audio data Serbo DSP S0/1 synchronized signal input
146 PVCC PVCC P Power supply for I/O Digital +3.3V
147 PF17/nFCE/LCD_CL1 CD_CTL2 O General-purpose port CD DRIVER control signal output CTRL2
148 PF16/FRB/LCD_DON CD_CTL1 O General-purpose port CD DRIVER control signal output CTRL1
149 PF15/NAF7/LCD_DATA15/SD_CD CD_R/W O General-purpose port Serbo DSP command I/F R/W output
150 PF14/NAF6/LCD_DATA14/SD_WP CD_DIO I/O General-purpose port Serbo DSP command I/F DATA input/output
151 PF13/NAF5/LCD_DATA13/SD_D1 FL/RST O General-purpose port FL reset signal output (Active = L)
152 PF12/NAF4/LCD_DATA12/SD_D0 - O General-purpose port OPEN (Unused : General-purpose Lo output setting
153 PF11/NAF3/LCD_DATA11/SD_SCLK - O General-purpose port OPEN (Unused : General-purpose Lo output setting
154 VCC VCC P Power supply for in Digital +1.2V
155 PF10/NAF2/LCD_DATA10/SD_CMD CUE1 I General-purpose port Fader IN input
156 VSS VSS G Digital GND
157 PVSS PVSS G GND for I/O Digital GND
158 PF9/NAF1/LCD_DATA9/SD_D3 PLAY1 I General-purpose port Fader IN input
159 PVCC PVCC P Power supply for I/O Digital +3.3V
160 PF8/NAF0/LCD_DATA8/SD_D2 CD_MCK O General-purpose port Serbo DSP command I/F DCK output
161 PF7/FSC/LCD_DATA7/nSCS1 - O General-purpose port SSU1_SCS : (Unused : General-purpose Lo output setting
162 PF6/FOE/LCD_DATA6/SSO1 - O General-purpose port SSU1_SIMO :(Unused : General-purpose Lo output setting
SSU1_SOMI :(Unused: LED2 connection for examination)
163 PF5/FCDE/LCD_DATA5/SSI1 LED2 O General-purpose port
LED2:LED green( Hi = On )
164 PF4/nFWE/LCD_DATA4/SSCK1 - O General-purpose port SSU1_CLK :(Unused : General-purpose Lo output setting
165 PF3/TCLKD/LCD_DATA3/nSCS0 FL_nCS O nSCS0 FL chip selection
166 PF2/TCLKC/LCD_DATA2/SSO0 FL_DATA O SSO0 FL serial data
167 PF1/TCLKB/LCD_DATA1/SSI0 - O General-purpose port SSU0_SOMI :(Unused : General-purpose Lo output setting
168 VCC VCC P Power supply for in Digital +1.2V
169 PF0/TCLKA/LCD_DATA0/SSCK0 FL_CLK O SSCK0 FL shift register clock
170 VSS VSS G Digital GND
171 PVSS PVSS G GND for I/O Digital GND
172 TMS TMS I Test mode selection JTAG I/F connector ⑨ H pin
173 PVCC PVCC P Power supply for I/O Digital +3.3V
174 TDI TDI I Test data input JTAG I/F connector ⑪ H pin
175 nASEBRKAK/nASEBRK /ASEBRKAK I/O Emulator hit I/O JTAG I/F connector ⑦ H pin
176 nTRST /TRST I Test reset input JTAG I/F connector ③ H pin
177 TDO TDO O Test data output JTAG I/F connector ⑤ H pin
178 TCK TCK I Test clock input JTAG I/F connector ① H pin
Serbo DSP FLAG3 signal input :
179 PB0/SCL0/PINT0/IRQ0 CD_FLAG3 I General-purpose port When C2 series cannot be corrected =H
When service mode is checked : IRQ0 (C2FX)
General-purpose
180 PB1/SDA0/PINT1/IRQ1 SUBSYQ I Serbo DSP S0/1 synchronized signal input(IRQ1:usable
port(Interrupt port)
General-purpose port When service mode playability is checked : IRQ2
181 PB2/SCL1/PINT2/IRQ2 CD_FLAG4 I
(Interrupt port) (C1F2)
41
DN-S3700
Pin
Pin Name Symble I/O Function
No.
Serbo DSP FLAG2 signal input (IRQ3:usable) :
General-purpose port The series of C2 irreparableness number of times
182 PB3/SDA1/PINT3/IRQ3 CD_FLAG2 I
(Interrupt port) exceeds the threshold=L
When service mode playability is checked : IRQ3 (C1F1)
183 PVCC PVCC P Power supply for I/O Digital +3.3V
184 PVCC PVCC P Power supply for I/O Digital +3.3V
General-purpose port Serbo DSP FLAG1 signal input
185 PB4/SCL2/PINT4/IRQ4 CD_FLAG1 I
(Interrupt port) (IRQ4:nonusable:use for 62pin)
General-purpose port
186 PB5/SDA2/PINT5/IRQ5 WFCK I Serbo DSP frame clock input
(Interrupt port)
187 PVSS PVSS G GND for I/O Digital GND
188 VSS VSS G Digital GND
189 PB6/SCL3/PINT6/IRQ6 - I General-purpose port Unused: Input setting(external PU) : ES → TC change point
190 PB7/SDA3/PINT7/IRQ7 - I General-purpose port Unused: Input setting(external PU) : ES → TC change point
191 VCC VCC P Power supply for in Digital +1.2V
192 PD15/D31/PINT7/SD_CD/nADTRG/TIOC4D PS2PWR I/O General-purpose port Keybord +5V supply on/off (ON = H, Off = L)
193 PD14/D30/PINT6/SD_WP/TIOC4C CD_LIMIT I General-purpose port CD Limit detection SW input
194 PD13/D29/PINT5/SD_D1/TEND1/TIOC4B PD1DISCI_DET3 O General-purpose port DISC detection(Disc In DET)
195 PD12/D28/PINT4/SD_D0/DACK1/TIOC4A JOGB I TIOC4A JOG pulse width measurement input B
196 PVSS PVSS G GND for I/O Digital GND
197 PD11/D27/PINT3/SD_SCLK/DREQ1/TIOC3D DISKO_DET I General-purpose port CD Disk Out detection output (detect=L)
198 PVCC PVCC P Power supply for I/O Digital +3.3V
199 PD10/D26/PINT2/SD_CMD/TEND0/TIOC3C CLUMP_SW I General-purpose port DISC detection(Disc Close DET)
200 PD9/D25/PINT1/SD_D3/DACK0/TIOC3B CD_BUSY I Deck1 ExOR input CD_BUSY : Servo DSP BUSY signal input (IRQ2 used)
201 PD8/D24/PINT0/SD_D2/DREQ0/TIOC3A TTA I Deck1 A aspect input Input A for TT pulse width measurement
202 PD7/D23/IRQ7/nSCS1/TCLKD/TIOC2B TTB I Deck1 B aspect input Input B for TT pulse number count
203 PD6/D22/IRQ6/SSO1/TCLKC/TIOC2A TTA I Deck1 A aspect input Input A for TT pulse number count
204 VCC VCC P Power supply for in Digital +1.2V
205 PD5/D21/IRQ5/SSI1/TCLKB/TIOC1B JOGB I Deck1 B aspect input Input for pulse number count
206 VSS VSS G Digital GND
207 PVSS PVSS G GND for I/O Digital GND
208 PD4/D20/IRQ4/SSCK1/TCLKA/TIOC1A JOGA I Deck1 A aspect input Input for pulse number count
209 PVCC PVCC P Power supply for I/O Digital +3.3V
Clock output of three Deck1/2 common aspects :
210 PD3/D19/IRQ3/nSCS0/DACK3/TIOC0D - O General-purpose port
OPEN (Unused : General-purpose Lo output setting)
Clock output of three Deck1/2 common aspects :
211 PD2/D18/IRQ2/SSO0/DREQ3/TIOC0C - O General-purpose port
OPEN (Unused : General-purpose Lo output setting)
OPEN (Unused: Monitor output for examination) :
212 PD1/D17/IRQ1/SSI0/DACK2/TIOC0B TP2 O General-purpose port
ES → TC change point
213 PD0/D16/IRQ0/SSCK0/DREQ2/TIOC0A JOGA I TIOC0A Input A for JOG pulse width measurement
214 D15 SHDB15 I/O D15 SDRAM/FLASH/ADSP D15 : ADSP connection addition
215 D14 SHDB14 I/O D14 SDRAM/FLASH/ADSP D14 : ADSP connection addition
216 PVSS PVSS G GND for I/O Digital GND
217 D13 SHDB13 I/O D13 SDRAM/FLASH/ADSP D13 : ADSP connection addition
218 PVCC PVCC P Power supply for I/O Digital +3.3V
219 D12 SHDB12 I/O D12 SDRAM/FLASH/ADSP D12 : ADSP connection addition
220 D11 SHDB11 I/O D11 SDRAM/FLASH/ADSP D11 : ADSP connection addition
221 D10 SHDB10 I/O D10 SDRAM/FLASH/ADSP D10 : ADSP connection addition
222 D9 SHDB9 I/O D9 SDRAM/FLASH/ADSP D9 : ADSP connection addition
223 D8 SHDB8 I/O D8 SDRAM/FLASH/ADSP D8 : ADSP connection addition
224 VCC VCC P Power supply for in Digital +1.2V
225 D7 SHDB7 I/O D7 SDRAM/FLASH/ADSP D7 : ADSP connection addition
226 VSS VSS G Digital GND
227 PVSS PVSS G GND for I/O Digital GND
228 D6 SHDB6 I/O D6 SDRAM/FLASH/ADSP D6 : ADSP connection addition
229 PVCC PVCC P Power supply for I/O Digital +3.3V
230 D5 SHDB5 I/O D5 SDRAM/FLASH/ADSP D5 : ADSP connection addition
231 D4 SHDB4 I/O D4 SDRAM/FLASH/ADSP D4 : ADSP connection addition
232 D3 SHDB3 I/O D3 SDRAM/FLASH/ADSP D3 : ADSP connection addition
233 D2 SHDB2 I/O D2 SDRAM/FLASH/ADSP D2 : ADSP connection addition
234 D1 SHDB1 I/O D1 SDRAM/FLASH/ADSP D1 : ADSP connection addition
235 D0 SHDB0 I/O D0 SDRAM/FLASH/ADSP D0 : ADSP connection addition
236 PVSS PVSS G GND for I/O Digital GND
237 PVCC PVCC P Power supply for I/O Digital +3.3V
238 PC13/RD/nWR SHRW O RD/nWR SDRAM_nWE + ADSP_HRnW : ADSP connection addition
239 PC12/CKE CKE O Clock is enable SDRAM CKE
B6TS mode setup(H:measure/L:setup) :
240 PC11/nCASU/nBREQ/AUDATA1 - O General-purpose port
(Unused : General-purpose Lo output setting)
42
DN-S3700
M12L128168A-5TG (IC102,502,503)
VDD 1 54 V SS
DQ0 2 53 DQ15
VDDQ 3 52 V S SQ
DQ1 4 51 DQ14
DQ2 5 50 DQ13
V S SQ 6 49 VDDQ
DQ3 7 48 DQ12
DQ4 8 47 DQ11 BLOCK DIAGRAM
VDDQ 9 46 V S SQ
DQ5 10 45 DQ10 CLK Clock
DQ6 11 44 DQ9 Generator Bank D
CKE
V S SQ 12 43 VDDQ Bank C
Bank B
DQ7 13 42 DQ8 Row
Address
VDD 14 41 V SS
Row Decoder
Address
LDQM 15 40 NC Buffer
Mode & Bank A
WE 16 39 UDQM Register Refresh
CAS 17 38 CLK
Counter
RAS 18 37 CKE
CS 19 36 NC
Sense Amplifier
A13 20 35 A11 L(U)DQM
Command Decoder
A12 21 34 A9 CS Column Column Decoder
Control Logic
A10 /AP 22 33 A8 Address
RAS
Latch Circuit
A1 24 31 A6 CAS &
Buffer
A2 25 30 A5 Counter Data Control Circuit DQ
WE
A3 26 29 A4
VDD 27 28 V SS
PIN DESCRIPTION
A0 ~ A11 Address Row / column address are multiplexed on the same pins.
Row address : RA0~RA11, column address : CA0~CA8
A12 , A13 Bank Select Address Selects bank to be activated during row address latch time.
Selects bank for read / write during column address latch time.
Row Address Strobe Latches row addresses on the positive going edge of the CLK with
RAS
RAS low. (Enables row access & precharge.)
Latches column address on the positive going edge of the CLK with
CAS Column Address Strobe CAS low. (Enables column access.)
Enables write operation and row precharge.
WE Write Enable
Latches data in starting from CAS , WE active.
Makes data output Hi-Z, tSHZ after the clock and masks the output.
L(U)DQM Data Input / Output Mask
Blocks data input when L(U)DQM active.
DQ0 ~ DQ15 Data Input / Output Data inputs / outputs are multiplexed on the same pins.
VDD / VSS Power Supply / Ground Power and ground for the input buffers and the core logic.
Isolated power supply and ground for the output buffers to provide
VDDQ / VSSQ Data Output Power / Ground improved noise immunity.
N.C No Connection This pin is recommended to be left No Connection on the device.
43
DN-S3700
BD7956FS (IC302)
54 28
BD7956FS
1 27
Block Diagram
44
DN-S3700
R5F71252N50FA (IC101)
FWE/ASEBRK/ASEBRKAK
PA0/POE0/RXD0
PB5/IRQ3/TIC5U
PA1/POE1/TXD0
PA2/IRQ0/SCK0
WDTOVF
ASEMD0
PLLVSS
EXTAL
XTAL
MD1
RES
NMI
VCC
VSS
VCL
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
PB3/IRQ1/POE1/TIC5V 49 32 PA3/IRQ1/RXD1/TRST
PB2/IRQ0/POE0 50 31 PA4/IRQ2/TXD1/TMS
PB1/TIC5W 51 30 PA5/IRQ3/SCK1
AVSS 52 29 PA6/TCLKA
PF7/AN7 53 28 PA7/TCLKB/SCK2/TCK
PF6/AN6 54 27 PA8/TCLKC/RXD2/TDI
PF5/AN5 55 26 PA9/TCLKD/TXD2/TDO/POE8
56 QFP-64 PA10/RXD0
PF4/AN4 25
LQFP-64
PF3/AN3 57 24 VSS
(Top view)
PF2/AN2 58 23 PA11/TXD0/ADTRG
PF1/AN1 59 22 VCC
PF0/AN0 60 21 PA12/SCK0
AVCC 61 20 PA13/SCK1
PB16/POE3 62 19 PA14/RXD1
PE15/TIOC4D/IRQOUT 63 18 PA15/TXD1
PE14/TIOC4C 64 17 PE0/TIOC0A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PE13/TIOC4B/MRES
PE12/TIOC4A
PE11/TIOC3D
VCC
PE9/TIOC3B
VSS
PE10/TIOC3C
VCL
PE8/TIOC3A
PE7/TIOC2B
PE6/TIOC2A/SCK1
PE5/TIOC1B/TXD1
PE4/TIOC1A/RXD1
PE3/TIOC0D/SCK0
PE2/TIOC0C/TXD0
PE1/TIOC0B/RXD0
Block Diagram
SH2 UBC
CPU
L bus (Iφ)
I bus (Bφ)
Peripheral bus
controller
I/O SCI CMT H-UDI INTC Power- WDT CPG MTU2 POE ADC
port down
(PFC) mode
control
[Legend]
ROM: On-chip ROM PFC: Pin function controller
RAM: On-chip RAM MTU2: Multi-function timer pulse unit 2
UBC: User break controller POE: Port output enable
H-UDI: User debugging interface SCI: Serial communication interface
INTC: Interrupt controller CMT: Compare match timer
CPG: Clock pulse generator ADC: A/D converter
WDT: Watchdog timer
CPU: Central processing unit
45
DN-S3700
W19B160BBT7 (IC103)
Block Diagram
Pin Description
LTC2624CGN (IC109)
Block Diagram
46
DN-S3700
PCM1791ADBR (IC802)
LRCK 1 28 MS
Block Diagram
BCK 2 27 MC
DATA 3 26 MDI LRCK
MUTE 4 25 MDO Audio Current VOUTL−
BCK Segment
SCK 5 24 MSEL Data Input
DATA I/F DAC VOUTL+
RST 6 23 ZEROL and
VDD 7 22 ZEROR I/V Buffer
DGND 8 21 VCCF
AGNDF 9 20 VCCL
8 D/S and Filter
VCCR 10 19 AGNDL MUTE Oversampling
AGNDR 11 18 VOUTL− Advanced
Digital Bias VCOM
RST Segment
VOUTR− 12 17 VOUTL+ Filter and
DAC
VOUTR+ 13 16 AGNDC MSEL and Vref
Modulator
VCOM 14 15 VCCC Function
Control
MDO
Current VOUTR+
MDI Function Segment
MC Control DAC VOUTR−
I/F and
MS I/V Buffer
SCK
AGNDF
AGNDL
VCCF
VCCL
AGNDC
AGNDR
DGND
VDD
VCCC
VCCR
Pin Description
TERMINAL
I/O DESCRIPTIONS
NAME PIN
AGNDC 16 − Analog ground (internal bias and current DAC)
AGNDF 9 − Analog ground (DACFF)
AGNDL 19 − Analog ground (L-channel I/V)
AGNDR 11 − Analog ground (R-channel I/V)
BCK 2 I Bit clock input (1)
DATA 3 I Serial audio data input (1)
DGND 8 − Digital ground
LRCK 1 I Left and right clock (fS) input (1)
MC 27 I Mode control clock input (1)
MDI 26 I/O Mode control data input (2)
MDO 25 O Mode control readback data output (3)
MS 28 I/O Mode control chip select input (4)
MSEL 24 I I2C/SPI select (1)
MUTE 4 I Analog output mute control (1)
RST 6 I Reset (1)
SCK 5 I System clock input (1)
VCCC 15 − Analog power supply (internal bias and current DAC), 5 V
VCCF 21 − Analog power supply (DACFF), 5 V
VCCL 20 − Analog power supply (L-channel I/V), 5 V
VCCR 10 − Analog power supply (R-channel I/V), 5 V
VCOM 14 − Internal bias decoupling pin
VDD 7 − Digital power supply, 3.3 V
VOUTL+ 17 O L-channel analog voltage output +
VOUTL– 18 O L-channel analog voltage output –
VOUTR+ 13 O R-channel analog voltage output +
VOUTR– 12 O R-channel analog voltage output –
ZEROL 23 O Zero flag for L-channel
ZEROR 22 O Zero flag for R-channel
(1) Schmitt-trigger input, 5-V tolerant
(2) Schmitt-trigger input and output. 5-V tolerant input. In I2C mode, this pin becomes an open-drain 3-state output; otherwise, this pin is a CMOS
output.
(3) 3-state output
(4) Schmitt-trigger input and output. 5-V tolerant input and CMOS output
47
DN-S3700
2. VFD MODULE
(VFD)DM200GINK(FL901)
R9 q
Pin Connection
Grid Assignment
48
DN-S3700
Segment Designation
49
DN-S3700
--MEMO--
50
DN-S3700
PRINTED WIRING BOARDS
8U-110042 POWER P.W.B. UNIT(1/2)
COMPONENT SIDE
51
DN-S3700
8U-110042 POWER P.W.B. UNIT(2/2)
FOIL SIDE
52
DN-S3700
8U-110043 PANEL P.W.B. UNIT(1/2)
COMPONENT SIDE
53
DN-S3700
8U-110043 PANEL P.W.B. UNIT(2/2)
FOIL SIDE
54
DN-S3700
8U-310011 MAIN P.W.B. UNIT
55
DN-S3700
--MEMO--
56
DN-S3700
NOTE FOR PARTS LIST
1. Parts for which "nsp" is indicated on this table cannot be supplied.
2. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.
3. Ordering part without stating its part number can not be supplied.
4. Part indicated with the mark "★" is not illustrated in the exploded view.
5. Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
6. Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING:
Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
● Resistors
Ex.: RN 14K 2E 182 G FR
* Resistance
1 8 2 1800ohm=1.8kohm
1 R 2 1.2ohm
● Capacitors
2 2 2 2200μF 2 R 2 2.2μF
2 2 2 2200pF=0.0022μF 2 2 1 220pF
Indicates number of zeros after efective number. Indicates number of zeros after effective numver.
(More than 2) (0 or 1)
2-digit effective number. 2-digit effective number.
・ Units:pF ・ Units:pF
・ When the dielectric strength is indicated in AC,"AC" is included after the dieelectric strength value.
57
DN-S3700
PARTS LIST OF P.W.B. UNIT
* Parts for which "nsp" is indicated on this table cannot be supplied.
* The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Note: The symbols in the column "Remarks" indicate the following destinations.
E3: U.S.A. & Canada model E2: Europe model
58
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
RESISTORS GROUP
R131,132 nsp RM73B--103DT(1608) +1608
R140 nsp RM73B--102DT(1608)
R141 nsp RM73B--103DT(1608) +1608
R144 nsp RM73B--103DT(1608) +1608
R146 nsp RM73B--103DT(1608) +1608
R149,150 nsp RM73B--102DT(1608)
R152-155 nsp RM73B--102DT(1608)
R156-164 nsp RM73B--103DT(1608) +1608
R166 nsp RM73B--222DT(1608)
R167 nsp RM73B--223DT(1608)
R172 nsp RM73B--222DT(1608)
R173 nsp RM73B--223DT(1608)
R178 nsp RM73B--222DT(1608)
R179 nsp RM73B--223DT(1608)
R183-188 nsp RS14B3D010JNBST(S)
R189 nsp RS14B3AR10J(ERX)
59
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
R190 nsp RM73B--103DT(1608) +1608
R191 nsp RM73B--102DT(1608)
R192 nsp RM73B--103DT(1608) +1608
R193,194 nsp RM73B--473DT(1608)
R195 nsp RS14B3AR10J(ERX)
R196 nsp RM73B--103DT(1608) +1608
R197,198 nsp RM73B--473DT(1608)
R233 nsp RM73B--103DT(1608) +1608
R234 nsp RM73B--102DT(1608)
R235 nsp RM73B--103DT(1608) +1608
R236 nsp RM73B--102DT(1608)
R237,238 nsp RM73B--103DT(1608) +1608
R239 nsp RM73B--202DT(1608)
R240 nsp RM73B--511DT(1608)
R241 nsp RM73B--103DT(1608) +1608
R803 nsp RM73B--152DT(1608)
R804 nsp RM73B--751DT(1608)
R806 nsp RM73B--183DT(1608)
R818 nsp RM73B--182DT
R819 nsp RM73B--622DT
R820 nsp RM73B--681DT
R822-824 nsp RM73B--182DT
R825,826 nsp RM73B--622DT
R827-829 nsp RM73B--681DT
R830 nsp RM73B--622DT
R837,838 nsp RM73B--151DT
R840 nsp RM73B--151DT
R843 nsp RM73B--151DT
R857 nsp RM73B--433DT(1608)
R858 nsp RM73B--302DT(1608)
R859 nsp RM73B--512DT(1608)
R861 nsp RM73B--101DT(1608)
R862 nsp RM73B--562DT(1608)
R863 nsp RM73B--332DT(1608)
R869 nsp RM73B--222DT(1608)
R911 nsp RS14B3D224JNBF (ERG)
R925 nsp RS14B3D104JNBF(ERG)
R927 nsp RS14B3DR51JNBST(S)
R931 nsp RS14B3D224JNBF (ERG)
R938 nsp RS14B3A821JNBST(S)
CAPACITORS GROUP
C101 nsp CK73B1H102KT +1608
C102,103 nsp CK73F1E104ZT +1608
C104 00D2544538900 CE04W1C100MT SMG/RE3
C105-109 nsp CK73F1E104ZT +1608
C110,111 nsp CC73CH1H220JT +1608
C112-114 nsp CK73F1E104ZT +1608
C115 00D2544538900 CE04W1C100MT SMG/RE3
C116-120 nsp CK73B1H102KT +1608
C121 nsp CK73B1E223KT +1608
C122-127 nsp CK73F1E104ZT +1608
C128 nsp CK73B1E223KT +1608
C129 nsp CK73F1E104ZT +1608
C130 nsp CK73B1E223KT +1608
60
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
C131,132 nsp CK73F1E104ZT +1608
C133 nsp CK73B1E223KT +1608
C134,135 nsp CK73F1E104ZT +1608
C136-138 nsp CK73F1H103ZT +1608
C139-144 nsp CK73B1E105KT +2125
C145 nsp CK73F1E104ZT +1608
C146,147 nsp CK73B1H102KT +1608
C148-151 nsp CK73F1E104ZT +1608
C152,153 nsp CK73B1H102KT +1608
C154,155 nsp CK73F1E104ZT +1608
C156,157 00D2570521949 CK73B1A474KT
C158,159 00D2544536915 CE04W1A470MT SMG/RE3
C160 nsp CK73F1H103ZT +1608
C161 00D2544538900 CE04W1C100MT SMG/RE3
C162-165 00D2570521949 CK73B1A474KT
C168 nsp CK73B1H103KT (1608) +1608
C169,170 nsp CK73B1H104KT +1608
C801 nsp CK73F1E104ZT +1608
C802 1340100235070 RA2-10V471MG3#8-T2
C803 nsp CK73F1E104ZT +1608
C804 1340100705030 RA2-50V100ME3E#8-T2
C805 nsp CK73F1E104ZT +1608
C806 1340100455070 RA2-25V101MF3#8-T2
C807 nsp CK73F1E104ZT +1608
C808 nsp CC73CH1H561JT +1608
C809,810 nsp CC73CH1H272JT +1608
C811-813 nsp CC73CH1H561JT +1608
C814 nsp CK73F1H103ZT +1608
C815,816 nsp CK73F1E104ZT +1608
C819,820 00MOA47601620 47 UF M 16V RA-2
C821 nsp CK73B1H102KT +1608
C822 nsp CK73B1H103KT (1608) +1608
C823 nsp CK73F1E104ZT +1608
C824 00D2544536928 CE04W1A101MT SMG/RE3
C825,826 nsp CC73CH1H121JT +1608
C828 nsp CK73B1A105KT +1608
C836,837 nsp CK73B1H682KT +1608
C838 nsp CK73F1H473ZT +1608
C846,847 00D2544710906 CE04W1C331MT HB5(KY)
C851-853 nsp CK73F1E104ZT +1608
C857 00D2544536915 CE04W1A470MT SMG/RE3
C860 00D2561059912 CF93A1H224JT (JL)
C901 nsp CK73B1H102KT +1608
C903 00D2538022707 CK45F2EAC103MC
C905 nsp CK73B1H102KT +1608
C906 00D2568038004 CF99--2EAC104M
C907 00D2538029713 CK45F2EAC471KC(KX)
C908 00MOA47601620 47 UF M 16V RA-2
C909,910 00D2538029713 CK45F2EAC471KC(KX)
C911 nsp CC73CH1H471JT +1608
C912 nsp CK73B1E683KT(1608) +1608
C913 nsp CK73B1E105KT +2125
C914 00D2544589713 CE04W2G101MC(KMG)
C915 00D2544525900 CE04W1H330MT SMG/RE3
C916 nsp CC73CH2A221JT +1608
C917 nsp CC73CH1H152JT +1608
61
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
C918 00D2534546708 CC45SL3D471JC
C919 132550013507S CK73B2J103KT(3216)
C921 134050077502S CE04W1J560MT HB5(KY)
C922 00D2544524985 CE04W1H100MT SMG/RE3
C923,924 00MOA47702520 470UF 25V M RA-2
C925 nsp CK73B1H105KT
C926 00D2544713712 CE04W1E222MC K35(KY)
C927 00D2544538942 CE04W1C101MT SMG/RE3
C928 00MOA47601620 47 UF M 16V RA-2
C929 134050078505S CE04W1J150MT E11(KY)
C931 nsp CK73B1H102KT +1608
C936 00D2538029713 CK45F2EAC471KC(KX)
C937 nsp CK73B1H102KT +1608
C939 nsp CK73B1H102KT +1608
C940 nsp GRM32EB31C476KE15L
C941 00D2544757707 CE04W1E272MC L25(KY)
C942 nsp GRM32EB31C476KE15L
C943 00D2544757707 CE04W1E272MC L25(KY)
C948 00D2544589713 CE04W2G101MC(KMG)
C951 00D2544710906 CE04W1C331MT HB5(KY)
C952 00D2544536928 CE04W1A101MT SMG/RE3
C953 nsp CK73B1E104KT +1608
C954 nsp CC73CH1H560JT +1608
C955 nsp CK73B1E104KT +1608
C956 00D2544536928 CE04W1A101MT SMG/RE3
C957 00D2544538913 CE04W1C220MT SMG/RE3
C958 nsp CK73F1E104ZT +1608
C959 00D2544651913 CE04W0J102MT H15(KY)
C961 nsp CK73B1H103KT (1608) +1608
C962 nsp CC73CH1H181JT +1608
C963 nsp CK73F1E104ZT +1608
C964 nsp GRM21BB31E475KA75
C967 nsp CK73F1E104ZT +1608
C970 nsp CK73F1E104ZT +1608
C971 nsp CK73B1E223KT +1608
C973,974 00D2544542705 CE04W1E471MC SMG/RE3
C975,976 nsp CK73B1E104KT +1608
C981 1340100445040 RA2-25V470ME3#8-T2
62
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
CY091 nsp 9P CONN.BASE(KR-PH)
CY112 00D2051260017 11P FFC BASE(9610SA)
CY141 nsp 14PEH CONNECTOR BASE
CY181 00D2051397003 18P FFC BASE(9610SA)
63
DN-S3700
8U-110043 PANEL P.W.B. UNIT ASS'Y
Ref. No. Part No. Part Name Remarks Q'ty New
SEMICONDUCTORS GROUP
IC701 00D2622953915 SN74HCT138APW
IC702 00D2623694901 SN74LV165APW
IC703,704 00D2623690905 TB62725BFNG
IC705 00D2622557900 SN74LV14APW-EL2 +REF
IC706 00MHC700405IZ TC74LVX04FT
64
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
LD743 00D3939608907 SLR342MC(TB7)
LD744 00D3939609906 SLR342DC(TB7)
LD745 263010029403S SLR-322DC
LD746 263010027407S SLR343BC7TT32
LD747,748 00D3939608907 SLR342MC(TB7)
LD749 263010028400S SLR-322VR
LD750 263010029403S SLR-322DC
LD751 263010027407S SLR343BC7TT32
LD752 00D3939609906 SLR342DC(TB7)
LD753 263010027407S SLR343BC7TT32
LD754,755 00D3939605900 SEL6427EP(TP5)
LD756,757 263010027407S SLR343BC7TT32
LD758 00D3939605900 SEL6427EP(TP5)
LD759 263010027407S SLR343BC7TT32
LD760 263010028400S SLR-322VR
LD761 263010029403S SLR-322DC
LD762 263010027407S SLR343BC7TT32
LD763 263010029403S SLR-322DC
LD764 263010027407S SLR343BC7TT32
LD765 263010028400S SLR-322VR
LD766-770 263010027407S SLR343BC7TT32
RESISTORS GROUP
VR701 00D2115648119 SLIDE VOLUME (100MM)
CAPACITORS GROUP
C701 nsp CK73F1E104ZT +1608
C702 00D2544302974 CE04W1A101MT(SRE)
C704 00D2544302974 CE04W1A101MT(SRE)
C707-709 nsp CK73F1E104ZT +1608
C710 00D2544302974 CE04W1A101MT(SRE)
C711,712 nsp CK73F1H103ZT +1608
C713-715 nsp CK73F1E104ZT +1608
C716 00D2544300918 CE04W0J100MT(SRE)
C717 nsp CK73F1E104ZT +1608
C719,720 nsp CK73F1E104ZT +1608
C724 nsp CK73F1E104ZT +1608
C725 00D2544302974 CE04W1A101MT(SRE)
C726 nsp CK73F1E104ZT +1608
C736 nsp CK73F1E104ZT +1608
C737 nsp CK73F1H103ZT +1608
C744 nsp CK73F1E104ZT +1608
C745 nsp CK73F1H103ZT +1608
C762,763 nsp CK73F1E104ZT +1608
C764 nsp CK73F1H103ZT +1608
C765 nsp CK73F1E104ZT +1608
C766 nsp CK73F1H103ZT +1608
C769 nsp CK73F1E104ZT +1608
C770 nsp CK73F1H103ZT +1608
C771 nsp CK73F1E104ZT +1608
C772 nsp CK73F1H103ZT +1608
C901 nsp CK73B1H102KT +1608
65
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
C902 00D2544306925 CE04W1H100MT(SRE)
C903 nsp CK73B1H105KT
C904 nsp CK73F1E104ZT +1608
C905,906 nsp CK73F1H473ZT +1608
C907 nsp CK73F1E104ZT +1608
C908 nsp CC73CH1H101JT +1608
C909 nsp CK73B1H102KT +1608
C910-912 nsp CC73CH1H100DT +1608
C913 nsp CK73F1E104ZT +1608
C914 nsp CK73F1H103ZT +1608
66
DN-S3700
8U-310011 MAIN P.W.B. UNIT ASS'Y
Ref. No. Part No. Part Name Remarks Q'ty New
SEMICONDUCTORS GROUP
IC101 00D2622813903 SN74AHCT08PW-EL2 +C
IC102 246810019601S M12L128168A-5TG
IC103 8R2461002000P S3700 ROM ASSY NOTE :
When update Firmware, please confirm a
(W19B160BBT7H) last version in SDI.
Use the service board after updating it.
RESISTORS GROUP
R153 nsp RM73B--562FT
R341-344 nsp 18K OHM 1/16W
R345 nsp 30K OHM +- 5% 1/16W
R354 nsp 30K OHM +- 5% 1/16W
R419 nsp RM73B--123FT +1608
R423 nsp RM73B--472DT(1608)
67
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
R428 nsp RM73B--103FT +1608
R429 nsp RM73B--562FT
CAPACITORS GROUP
C101 nsp CK73F1E104ZT +1608
C102 nsp CK73B1H103KT (1608) +1608
C103 nsp CK73B1E104KT +1608
C104 nsp CC73CH1H470JT +1608
C105 nsp CK73F1E104ZT +1608
C106 nsp CK73B1E104KT +1608
C107 nsp CK73B1H103KT (1608) +1608
C108 00D2575003983 CC73CH1H470JT
C109 nsp CK73B1E104KT +1608
C110,111 nsp CK73B1H103KT (1608) +1608
C112 nsp CK73F1E104ZT +1608
C113 nsp CK73B1A105KT +1608
C114-117 nsp CK73F1C104ZT +1005
C118 00D2544464951 CE67C0J220MT(MV-B) +REF
C119,120 nsp CK73F1C104ZT +1005
C121,122 nsp CC73CH1H150JT +1608
C124 nsp CK73B1E104KT +1608
C127 nsp CC73CH1H6R0DT +1608
C128 00D2544464951 CE67C0J220MT(MV-B) +REF
C129 nsp CC73CH1H6R0DT +1608
C130 nsp CK73B1E104KT +1608
C132,133 nsp CK73F1C104ZT +1005
C134 nsp CK73B1H103KT (1608) +1608
C135,136 nsp CK73F1C104ZT +1005
C137 00D2544464951 CE67C0J220MT(MV-B) +REF
C138 nsp CK73F1C104ZT +1005
C139 nsp CK73B1H332KT +1608
C140-142 nsp CK73F1C104ZT +1005
C143 nsp CK73B1H332KT +1608
C144,145 nsp CK73F1C104ZT +1005
C146 00D2575003983 CC73CH1H470JT
C147,148 nsp CK73F1C104ZT +1005
C149 00D2575003983 CC73CH1H470JT
C150,151 nsp CK73F1C104ZT +1005
C152 00D2575003983 CC73CH1H470JT
C153-156 nsp CK73F1C104ZT +1005
C157 nsp GRM32EB31C476KE15L
C158-173 nsp CK73F1C104ZT +1005
C174 00D2544464951 CE67C0J220MT(MV-B) +REF
C175 00D2575003983 CC73CH1H470JT
C176,177 00D2574018908 CE67C1A100MT(PXA)
C178-182 00D2575003983 CC73CH1H470JT
C184 00D2575003983 CC73CH1H470JT
C301,302 nsp CK73B1A104KT +1005
C303 00D2574012920 CE67C1C470MT (RV2) +REF
C304 nsp CK73B1A104KT +1005
C305 00D2544655922 CE67C0J470MT (RV2) +REF
C306,307 nsp CK73B1H103KT (1608) +1608
C309 00D2574012920 CE67C1C470MT (RV2) +REF
C310 00D2544656947 CE67C1A101MT (RV2)
C311 nsp CK73B1E104KT +1608
68
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
C312 00D2544656947 CE67C1A101MT (RV2)
C313 00D2574012917 CE67C1C220MT (RV2) +REF
C314,315 nsp CK73B1E104KT +1608
C316 00D2574012904 CE67C1C100MT (RV2B55 +REF
C317 nsp CK73B1E104KT +1608
C318 nsp CC73CH1H471JT +1608
C319 nsp CK73B1E104KT +1608
C320 00D2544656947 CE67C1A101MT (RV2)
C321 nsp CK73B1A224KT +1608
C323,324 nsp CK73B1E104KT +1608
C325 00D2544656947 CE67C1A101MT (RV2)
C326-328 nsp CK73B1A105KT +1608
C329 nsp CK73B1H332KT +1608
C330 nsp CK73B1H152KT +1005
C331 nsp CK73B1A224KT +1608
C332 nsp CK73B1A104KT +1005
C333 nsp CK73B1E104KT +1608
C334 00D2544656947 CE67C1A101MT (RV2)
C335 nsp CK73B1A104KT +1005
C336 nsp CK73B1E104KT +1608
C337 nsp CK73B1A104KT +1005
C338 00D2544656947 CE67C1A101MT (RV2)
C339 00D2574012917 CE67C1C220MT (RV2) +REF
C340 nsp CK73B1E104KT +1608
C341 nsp CK73B1A104KT +1005
C342 nsp CC73CH1H221JT +1608
C343 nsp CK73B1A104KT +1005
C344 00D2574012904 CE67C1C100MT (RV2B55 +REF
C345 nsp CK73B1E104KT +1608
C346 nsp CK73B1E103KT(1005)
C347,348 nsp CK73B1A104KT +1005
C349 00D2574012917 CE67C1C220MT (RV2) +REF
C350 00D2574012904 CE67C1C100MT (RV2B55 +REF
C351-353 nsp CK73B1E104KT +1608
C354 nsp CK73B1A105KT +1608
C355 nsp CK73B1A104KT +1005
C356 nsp CK73F1E104ZT +1608
C357 nsp CK73F1H103ZT +1608
C358,359 nsp CK73B1A104KT +1005
C401,402 nsp CK73B1E104KT +1608
C403 00D2574012920 CE67C1C470MT (RV2) +REF
C407-409 nsp CK73B1H103KT (1608) +1608
C410,411 nsp CK73F1E104ZT +1608
C412 nsp CK73B1H103KT (1608) +1608
C413-415 nsp CK73B1A106KT +2125
C416 nsp CK73B1E103KT(1005)
C417,418 nsp CK73F1E104ZT +1608
C419 nsp CK73B1E104KT +1608
C420 nsp CK73F1H103ZT +1608
C421 00D2544655906 CE67C0J220MT (RV2) +REF
C422 nsp CK73F1E104ZT +1608
C423 00D2544655922 CE67C0J470MT (RV2) +REF
C424 nsp CK73B1E104KT +1608
C425 nsp CK73F1H103ZT +1608
C426 nsp CK73B1E104KT +1608
C427 00D2544655906 CE67C0J220MT (RV2) +REF
69
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
C428 nsp CK73B1E104KT +1608
C429 00D2574012920 CE67C1C470MT (RV2) +REF
C430 00D2570521949 CK73B1A474KT
C433 nsp CK73B1A106KT +2125
C434 00D2570039910 CK73B0J226MT
C501 00D2544464951 CE67C0J220MT(MV-B) +REF
C502 nsp CK73F1C104ZT +1005
C504 nsp GRM32EB31C476KE15L
C505-521 nsp CK73F1C104ZT +1005
C522 00D2544464951 CE67C0J220MT(MV-B) +REF
C523-534 nsp CK73F1C104ZT +1005
C535 00D2544464951 CE67C0J220MT(MV-B) +REF
C536 nsp CK73F1E104ZT +1608
70
DN-S3700
---MEMO---
71
DN-S3700
EXPLODED VIEW
A-3
A-2
A-4
B-7
A-1
B-6
B-4
B-1
B-2
B-5
B-3
WARNING:
Parts marked with this symbol have critical
characteristics.
Use ONLY replacement parts recommended by
the manufacturer.
72
DN-S3700
PARTS LIST OF EXPLODED VIEW
* Parts for which "nsp" is indicated on this table cannot be supplied.
* P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts.
* The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Note: The symbols in the column "Remarks" indicate the following destinations.
E3: U.S.A. & Canada model E2: Europe model
73
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
22-4 - BUTTON LENS(CIRCLE) 5 *
23 409410003005P FRONT SIDE COVER 2 *
25 409410004008P REAR SIDE COVER 2 *
26 422510027003P FADER PLATE 1 *
27 nsp BUFFER 2 *
28 481510013003P FRONT LENS 1 *
29 nsp FRONT LENS STOPPER 1 *
31 411510066008P M-BUTTON(3PS) 1 *
32 411510066015P M-BUTTON(3PS) 1 *
33 411510066022P M-BUTTON(3PS) 1 *
34 411510066039P M-BUTTON(3PS) 1 *
35 481510016002P BUTTON LENS(RECTANGLE) 3 *
36 411010083008P RUBBER-BUTTON 123 1 *
37 411010043000P RUBBER BUTTON (PP&T) 1 *
38 411010047002P RUBBER BUTTON (SELECT) 1 *
39 481510008001P CIRCLE LENS (L) 1 *
40 481510015009P CIRCLE LENS (R) 1 *
41 411010067006P M-BUTTON CIRCLE ASSY 5 *
41-1 - M-BUTTON (CIRCLE) 5 *
41-2 - M-BUTTON LENS(CIRCLE) 5 *
42 411510050003P M-BUTTON(2P) 1 *
43 411510050010P M-BUTTON(2P) 1 *
44 481510010004P M-BUTTON(3PR) 1 *
45 00D1131950002 TOGGLE SW KNOB 1
46 nsp DISPLAY BASE 1 *
47 nsp INSULATION SHEET(PANEL) 1 *
48 nsp TOP SHIELD 1 *
49 nsp BRACKET 1 *
50 nsp BUSH 5
51 nsp MOTOR BASE 1 *
52 FG3700 DD MOTOR UNIT 1 *
53 412510044001P SELECT KNOB ASSY 1 *
53-1 - KNOB BUSH(SELECT) 1 *
53-2 - KNOB (SELECT) CAP 1
54 412510042005P KNOB 1 *
55 00D1131951014 FADER KNOB 1
56 416510012006P WINDOW 1 *
57 nsp TURN TABLE SUB ASSY 1 *
57-1 469410001001P TURN TABLE 1 *
57-2 445010078009P SLIP SHEET 1 *
58 8P3561000300P ANALOG DISC SUB ASSY 1 *
58-1 - ANALOG DISC 1 *
58-2 - SLIP MAT 1 *
58-3 - DISC CLAMPER 1 *
58-4 - FIX PLATE 1
59 nsp SPACER 1
60 nsp CORD HOLDER (L50) 5
61 00D2062089106 AC CORD W/CON.E2 E2 1
61 00D2062155001 AC CORD W/CON.E3 E3 1
62 nsp PUSH RIVETS 1
★ 65 nsp WIRE CLAMPER 1
★ 66 nsp R.SHEET E2 SUB ASSY E2 1
★ 66 nsp R.SHEET E3 SUB ASSY E3 1
★ 67 nsp RATING LABEL BASE 1
★ 68 nsp CAUTION LABEL 1
69 445D10086000P INSULATION SHEET 1 *
74
DN-S3700
Ref. No. Part No. Part Name Remarks Q'ty New
★ 70 nsp INST LABEL E2 1
★ 71 nsp FCC/CLASS B CAUTION E3 1
★ 72 nsp C-UL LABEL(80X7) E3 1
★ 73 nsp LABEL CDRH E3 1
★ 74 nsp MANUFAC.DATE SUB ASS E3 1
WIRES
★ 81 606050058013P 15P FFC(1.0) L=280 1
★ 82 606050028012P 7P FFC(1.0) L=240 1
★ 83 606050028029P 11P FFC(1.0) L=110 1
★ 84 606050058006P 18P FFC(1.0) L=90 1
★ 85 606050059009P 22P FFC(1.0) L=270(AD) 1
★ 86 nsp 1P SRA-SRA L=60 1
★ 87 nsp 14P EH-EH L=170 1
★ 88 nsp 2P VA-VA CON.CORD 1
SCREWS
100 503350001009S 4X14 CBS-B 4
101 0RD4737002034 3X6 CBTS (S)-B 12
102 0RD4713303016 3X6 CBS-Z 5
103 0RD4713303029 3X6 CBS-B 2
104 0RD4713303016 3X6 CBS-Z 3
105 0RD4737500044 3X8 CBTS (P)-B 2
106 0RD4713303016 3X6 CBS-Z 1
107 0RD4713202010 2.6X5 CBS 5
108 0RD4713303016 3X6 CBS-Z 4
109 0RD4770018001 WASHER (P-87) 4
110 0RD4737002034 3X6 CBTS (S)-B 2
111 00M51260306U0 SCREW 1
112 0RD4713303029 3X6 CBS-B 2
113 00M51971704U0 SCREW 2
114 0RD4737002034 3X6 CBTS (S)-B 2
115 0RD4737532009 2.6X6 CBTS(P)-W-Z 2
116 0RD4737002034 3X6 CBTS (S)-B 2
117 0RD4737506022 2X6 CBTS(P)-B 2
118 0RD4737519006 2.6X8CBTS(P)-B 4
119 0RD4737532009 2.6X6 CBTS(P)-W-Z 2
120 0RD4737519006 2.6X8CBTS(P)-B 2
121 0RD4737532009 2.6X6 CBTS(P)-W-Z 6
122 0RD4737519006 2.6X8CBTS(P)-B 43
123 0RD4737002034 3X6 CBTS (S)-B 7
124 0RD4713404025 4X8 CBS 4
125 0RD4737006027 3X10 CBTS (S)-B 10
126 0RD4737507021 2X4 CBTS-(P)-B 3
127 501350004002S 2X10 CPS-Ni 4
128 0RD4737519006 2.6X8CBTS(P)-B 4
129 00M51480306A9 SCREW 1
130 0RD4713303016 3X6 CBS-Z 4
131 00M51480306A9 SCREW 1
132 516350003001S 3X10 CFTS-(S)Ni 8
133 00M51260308U0 SCREW 1
75
DN-S3700
PACKING VIEW
8 9 10 11 12 13
1
2
5
14
15
5
3 7
16
16
76
DN-S3700
WIRING DIAGRAM
/#+0 %:
2-4
/)0&
%; %: %: %9 2.#66'4
2((% 5# 2((% 5% 2-4 2A-4&#. &+5%$
8 8 8& 8 2.#66'4
(.A%.- (.A%.- 8& 8 &+5%#
(.A# (.A# &0)& &)0& %9
(.A%5 (.A%5 8 8 %8
(.A456 (.A456 &)0& &)0& %7
&)0& &)0& 8 8 #
&)0& &)0& &)0& &)0& $
%
8 /1614&4+8'
2#0'. 2#0'. %: %;
2((%U 5& 2((% 5#
&)0& &)0& %: %;
%9 %: %; %9 %; %: 66# 2.#66'4 2'* 2'*
2&5 2-4U 2-4U 2&5 2((%U 5$ 2((% 5% 66$ 2.#66'4 /)0& /)0&
5' 2A-';5% 5% &)0& &)0& 4'7 4'7
5' .& .& 2A-';5% 5% ,1)# &+5%# &7 &7
5& .& .& 2A-';5% 5% ,1)$ &+5%$ 4'8 4'8
.& .& 2A5%- 5%- &)0& &)0& &8 &8
.& .& &)0& &)0& 57$A5%- 1RGP 4'9 4'9
%&+0.'& 5& 5& 2A$.0- $.+0- 57$A/15+ 57$A/15+ &9 &9
5& 5& 2A.'& .'& 57$A/+51 57$A/+5 /)0& /)0&
5& 5& 2A-'; -'; &)0& &)0& 8 8
%: %9 5' 5. 8 8 57$A456 456 8 8
2-4U 4& 2&5 5' 5. 8 8 57$A/& 57$A/& /)0& /)0&
5' 5' 5. &)0& &)0& 57$A(9' 57$A(9' 8 8
5' 5' 5. 2+6%* 2+6%* 57$A+06 57$A+06 8 8
5' 5' 5. 2+6%*% %'06 56$1 56$ /)0& /)0&
.& 56$1 56$1 25294 25294
&)0& &)0& &)0& &)0&
5.+&'84 #7&+1
%: %:
%: %9 2((%U 2 75$A%100'%614 %: %9 %;
2-4U 2&5 )0&A.& 75$ 2/&,#%- 2A-4&#. 2-4
8 8 )0&A.& 25&CVC 8# 8#
&)0& &)0& 0% %100'%614 0%
2+6%* 2+6%* *(/ )0& #)0& #)0&
2+6%*% 2+6%*% /& 8
%&A.& 25%NQEM 8# 8#
84A&8& %: 0%
(9&$16* 84A%& 75$ $ )0& &)0& &)0&
0% 8$75 )0& 8 8
' &2 75$ $ )0& 8 8
%9 %: 8%% &/
2&5 2-4U 8% )0&
)0&A2&
(
$ %: %;
# 2((%U 5& 2((% 5#
4( &)0& &)0&
%&&8&A59 52&+( 52&+(
& .4%- .4%-
% &)0& &)0&
6 $%- $%-
6 &)0& &)0&
( # #
( &)0& &)0&
/%.- /%.-
%&/GEJC &)0& &)0&
%: /76' /76'
2((% 5#
.1#&+0)
.1#&+0) ,-
*$ /+0+,#%-
*9 (CFGTA+0
*9 5
*8 4 (CFGTA+0
*8 6
*7
*7
219'4 %:
7 ,#%-A
8 6:
9 )0&
.+/+6A59 4:
(''&/6 0% &.KPM
(''&/6 0%
&+5%176A&'6 )0&
&+5%+0A&'6 0%
&)0& 0%
&+5%A','%6A.'& ()
%.15'A'0&A59 ()
&+5%A+0A.'&
77
DN-S3700
--MEMO--
78
DN-S3700
MEASURING METHOD AND WAVEFORMS
To check the waveforms on the MAIN UNIT, the GND (-) probe of the oscilloscope to “GND” point.
(Except for lnner SW, TRVSW)
NOTES
Measuring Disc: CD/TCD-784
(It is better to use wires for extending between the probe and test points.)
• When watching the RF1 waveform, use the extending wire as short as possible.
• When RF1 waveform is noisy or cannot discriminate the eye-pattern, replace the Mecha Unit after measuring the lop.
• ① ~ ⑬ points have the certain test points shown below.
79
DN-S3700
Q3 Q2 u Q0yo r e w
80
DN-S3700
WAVEFORMS
8U-310011 MAIN UNIT
RF Waveform
①EQ0
㩿RF1) 1.0Vp-
㪈㪅㪇㪭㫇㪄
[0.2VAC]
䌛㪉㪇㪇㫅㪪䌝
⑧TDOUT
②LDIN [2VDC]
[2VAC䌝
⑨T+
[0.5VAC]
③LDO+
[2VDC]
④LDO- ⑩T-
[2VAC] [0.5VAC]
[400䌭S] [200ȝS]
䌛㪋㪇㪇䌭㪪䌝 䌛㪉㪇㪇㱘㪪䌝
⑪SDOUT
②LDIN [2VDC]
[2VDC]
⑫FEEDMT+
[0.5VAC]
③LDO+
[2VAC]
④LDO- ⑬FEEDMT-
[2VAC] [0.5VAC]
[400䌭S] [40䌭S]
䌛㪋㪇㪇䌭㪪䌝 䌛㪋㪇䌭㪪䌝
⑪CLVOUT
⑤FDOUT [2VDC]
[2VDC]
⑥F+ ⑫FEEDMT+
[1VAC] [0.5VAC]
⑦F- ⑬FEEDMT-
[1VAC] [0.5VAC]
[1S] [40䌭S]
䌛㪈㪪䌝 䌛㪋㪇䌭㪪䌝
81
DN-S3700
2. MOTORDRIVE UNIT : TEST POINT AND WAVEFORMS
CY141
U
V
W
㪬 㪭 㪮
82
DN-S3700
--MEMO--
83
DN-S3700
NOTE FOR SCHEMATIC DIAGRAM
WARNING:
Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
CAUTION:
Before returning the unit to the customer, make sure you
make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps,
or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the unit is defective.
WARNING:
DO NOT return the unit to the customer until the problem is
located and corrected.
NOTICE:
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM
M=1,000,000 OHM
ALL CAPACITANCE VALUES IN MICRO FARAD.
P=MICRO-MICRO FARAD
EACH VOLTAGE AND CURRENT ARE MEASURED AT
NO SIGNAL INPUT CONDITION.
CIRCUIT AND PARTS ARE SUBJECT TO CHANGE
WITHOUT PRIOR NOTICE.
84
DN-S3700
1 2 3 4 5 6 7 8
z
+8V
z
-8V
z
+40V
z
z
B
+5V
+3.3V
C
+8.9V
+9V +9V
-9V
-9V
+5V
+5V
-8.9V
D
+9V
-9V
+9V
+5V E
+5V
Analog Audio SIGNAL LINE
Digital Audio SIGNAL LINE
V
B
DN-S3700
1 2 3 4 5 6 7 8
+3.3V
+5V
q
+3.3V
B
Q0
u y
t
C
+3.3V
i Q1
+1.5V
+12V
w D
Q6
Q5
r
e
Dital Audio SIGNAL LINE
DN-S3700
1 2 3 4 5 6 7 8
+3.3V +5V
+3.3V
+1.2V A
+5V
+3.3V
E
+3.3V
DN-S3700
1 2 3 4 5 6 7 8
+3.3V
+3.3V
+3.3V
C
E
+3.3V +3.3V
+1.2V
+1.2V +3.3V
DN-S3700
1 2 3 4 5 6 7 8
DN-S3700