Professional Documents
Culture Documents
Lifting Guide
Lifting Guide
com
GUIDE
LIFTING
Contents
Download HSE Docs hseprof.com
Lifting equipment in general Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
The ant and the elephant . . . . . . . . . . . . . . . . . . 5
Standards, laws and regulations . . . . . . . . . . . . 6-7
Expressions and terms . . . . . . . . . . . . . . . . . . . 8-9
Safety and responsibility. . . . .. . . . . . . . . . . . 10-13
Components of lifting equipment . . . . . . . . . 14-31
every time
Lifting operations call for a very high Maintenance Page
level of safety. The lifting equipment and Regular inspection. Storage . . . . . . . . . . . . . 94-95
the way it is used are crucial to your Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 96-98
safety on site. For this reason, it is Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99-103
important to choose a responsible supplier. Steel wire rope . . . . . . . . . . . . . . . . . . . . . 104-105
Gunnebo Lifting is a leading manufacturer Components . . . . . . . . . . . . . . . . . . . . . . .106-107
of lifting equipment. When it Soft lifting equipment . . . . . . . . . . . . . . . .108-109
comes to quality we leave nothing to Keeping a register . . . . . . . . . . . . . . . . . . .110-111
chance. That is something you can rely on. Inspection planning . . . . . . . . . . . . . . . . . .112-113
Edition 2, eng.
Lifting equipment in general
Download HSE Docs hseprof.com
Maintenance
4 5
Lifting equipment in general
Download HSE Docs hseprof.com
Standards, laws
and regulations
Several organisations are involved in the
development of standards, legislation and
inspection procedures in the field of lifting.
We recommend that you obtain relevant information
from your national Health & Safety Authority.
6 7
Lifting equipment in general
Download HSE Docs hseprof.com
Expressions
and terms
Lifting equipment is everything used to connect Total ultimate elongation is the elongation of a
a load to the crane hook, i. e. wire rope slings, chain at the moment of breaking, in percent, of the
chain slings, roundslings, webbing slings, lifting original length. It is a measure of toughness.
beams etc.
Effective length is the length between the load-
WLL (working load limit) is the maximum mass that bearing points of an unloaded lifting sling or chain
the lifting equipment is authorized to sustain in sling.
general lifting service.
SF (safety factor) is the relationship between Effective length of a one-legged lifting sling with two
breaking force and WLL. Note! The safety factors components.
for chain, steel wire rope and soft slings differs.
8 9
Lifting equipment in general
Download HSE Docs hseprof.com
10 11
Lifting equipment in general
Download HSE Docs hseprof.com
Safety and
responsibility
The demands on suppliers for quality assurance By close co-operation with our suppliers we ensure
systems, approved according to ISO 9001:2000 are guaranteed that the raw material complies with our
growing even stronger. The ISO 9001 system ensures high demands.
that the supplier has documented routines for all
activities which may influence on customer related We work continuously to improve our existing range
quality. A third part auditor continuously assesses the of products and develop new innovative products in
conformity of the quality system. order to solve all possible kinds of lifting situations.
12 13
Lifting equipment in general
Download HSE Docs hseprof.com
Chain Grade Surface Type Nom. Min Load factors Typical Applications
treatment breaking Max Proof Breaking
strain Load Force Force
(N/mm2) factors
Galvanized (Z) KL 240 1 2,4 4,5 Agriculture, anchorage
2 Polished (B) HL 240 1 2,4 5,2 General consumer use
LL 240 1 2,4 5,8
Painted red (R) KL 360 1 2,4 4,5 For use in hot environments (KL)
3 HL 360 1 2,5 5,2
LL 360 1 2,4 5,5
Painted blue (A) HL 500 1 2,4 4,5 Lashing bundling, lumbering
5 LL 500 1 2,5 5,2
Painted yellow (U) KL 800 1 2,5 4,0 Chain sling EN818-2 / EN818-4
painted black (B) KLF 800 1 2,5 5,0 Lifting equipment (KL),
8 Galvanized (Z) HL 800 1 2,5 5,0 Container lashing (HL, HLC).
ML 800 1 2,5 5,0 towing, fishing and lumbering.
LL 800 1 2,5 5,0 (KL, ML, LL).
Painted blue (A) KL 1000 1 2,5 4,0 Chain sling EN818-2 / 818-4
10(8+) with increased lifting capacity
14 15
Lifting equipment in general
Download HSE Docs hseprof.com
0
0 10 20 30 40 50 60
% elongation
16 17
Lifting equipment in general
Download HSE Docs hseprof.com
18 19
Lifting equipment in general
Download HSE Docs hseprof.com
Location of the mechanical Multiple legs
splices or ferrules. Multilegged lifting slings may consist
The length (h) of the eye on a of two, three or four legs. A
steel wire rope must be at least master link joins the legs at the
15 x d. top. The legs of 3- and 4-legged
slings are connected into
d = rope diameter intermediate links.
Min 20xd
20 21
Lifting equipment in general
Download HSE Docs hseprof.com
Soft lifting
equipment To know
One single cover heavy duty tube for the
Roundslings roundsling is actually stronger than a double
Roundslings consist of an endless load-bearing cover tube with two thin layers. Our tests show
sling made of polyester fibre, protected from dirt that the quality of the tube is of utmost
and wear with a single- or double-layered cover importance for the lifetime of the product.
of polyester fabric. There are two types of We refute the argument that when the first layer
covers: sideseam with double cover which give a on a double cover sling is damaged you can still
stiffer roundsling and the seamless for softer use the sling because there is a risk that sharp
version. objects have entered in between the layers and
may cause hidden damages. Another advantage
Endless Webbing slings with the single cover roundsling is the protected
These webbing slings consist of a woven label which also makes the sling stiffer so it can be
polyester webbing sewn into an endless loop. passed through narrow spaces.
They can be used in the same way as roundslings
but are limited to lower working loads.
22 23
Lifting equipment in general
Download HSE Docs hseprof.com
Material properties
Polyester is resistant to acids but not to alkalis, e.g.
ammonia and caustic soda.
Lifting components
• The melting point is 260oC, but polyester lifting The grade of the lifting components must match the
equipment must not be used with loads or ambient grade of the chain (usually grade 8 or grade 10 (8+).
temperatures hotter than 100oC. The size designation usually refers to the size of the
chain with the same strength, e.g.:
• The strength is not affected by water.
G-10-8 = Coupling link, type G, suitable for
Water absorption is negligible.
10 mm chain, grade 8 (max. load 3.2 tonnes)
• Note that friction and sharp edges can
quickly wear and cut polyester.
• Lifting equipment in polyester has a blue
identification tag.
Master Links
Master links can be drop forged or forged and welded
from round steel. There are two basic designs:
Polypropylen
- single master link, for one- and two-legged
• The melting point is 165oC. lifting slings
• Polypropylene must not be used with loads - master link, with sub links for three- and
hotter than 80oC. four-legged lifting slings.
• Lifting equipment in polyproplene has a brown
identification tag.
Master Link, M Master Link MF/ Master Link MG
For use with MFX All-in-one
Safety factor G-link top link
For use with
Roundslings and webbing slings = 7:1 according Berglok,
to EN-standards. G-link or
24 25
Lifting equipment in general
Download HSE Docs hseprof.com
Couplings Hooks
Examples of the most common mechanical couplings For steel wire rope and chain
are shown below. For chain there are several alternative (G-couplinglink/Berglok)
connection systems: G-coupling link, Berglok, The SK-
system and direct connection to clevis-type hooks. Safety hook, Sling hook, Sling hook,
BK/OBK EKN EK
Coupling link, G Berglok chain coupler, BL
A foolproof assembly system Will not
in combination with matching open when
under direct
links and hooks. load and
prevents
the hook
from cathing With latch to pre- Suitable when
when lifting. vent unintentional latching hooks can
unloading. not be used.
Half link, For use with Roundsling coupling, Foundry hook, OKE Grabhook, OG
SKT matching SK- SKR For use with
system com- matching SK- Not for use with
ponents. system com- With a wide Berglok. No load
ponents. opening derating. Supporting
to accept bridge prevents
large chain deformation.
diameter.
Clevis shackle Dee shackle Bow shackle
GSA SA
For con- Swivel safety hook, Swivel latch hook,
nection in LKN/LKNK
BKL/BKLK
chain
With a With a
swiveling swiveling
eye to eye to
C-grab, CG C-grab, CGD C-lok , CL enable enable
For use with For use For use with rotation. rotation.
master link with master link
MF. master MF.
link MF.
26 27
Lifting equipment in general
Download HSE Docs hseprof.com
lifting equipment
Will not open when With latch to pre- Suitable when
under direct load and vent unintentional latching hooks
prevents the hook unloading. can not be used. Steel rope Clamping thimble
from cathing when
lifting.
clamp
Thimble
Clevis swivel Grab hook, GG Clevis egg-
safety hook, Shortening hook link, CEL
BKH with supporting
Especially for bridge to prevent
chain hoists. deformation of
With ball bea- the load bearing
ring to enable link. No load
rotation. derating. Masterlink for
direct connection Along with ferrules, the most common
SK-System with chain. components, for assembling steel wire rope
Sling hook Master Link, Rollerbearing slings.
SKN/ESKN closed SKG. swivel, SKLI
Open SKO.
28 29
Lifting equipment in general
Download HSE Docs hseprof.com
30 31
Choosing equip ment
Download HSE Docs hseprof.com
32 33
Choosing equip
Download HSE Docs hseprof.com
ment
34 35
Choosing equip
Download HSE Docs hseprof.com
ment
Load table for
grade 8 chain In the case of asymmetric loading
• 2-legged sling calculated as the corresponding
slings
1-leg sling.
• 3- and 4-legged sling calculated as the
corresponding 1-leg sling (If it is certain
that 2-legs are equally carrying the major part of
Working Load Limits in tonnes the load it can be calculated as the corresponding
for chain slings grade 8, according to EN 818-4 2-legged sling.
36 37
Choosing equip
Download HSE Docs hseprof.com
ment
Load table for The table below shows the maximum permitted
load for the most common steel rope slings,
tensile grade 1770 N/mm2 and 1960 N/mm2,
steel wire rope according to EN13414-1
Wire
dim.
mm. 2-legged 3- & 4-legged Parallell endless
1-legged 1-legged α 0-45º
β α 90-120º α 0-90º
β α 90-120º
β endless choke choke
α α
β 0-45º α β 45-60º β 0-45º β 45-60º hitch hitch
38 39
Choosing equip
Download HSE Docs hseprof.com
ment
Steel rope slings
When planning a lift where technical data on Lifting angle Factor KL
weight , centre of gravity etc. are known, trigono-
α Number of legs
metrics may be used for calculating the maximum
2 3-4
load on the lifting equipment. Basis for the
calculation is the column for 1-legged slings, or the 0-90° 1,4 2,1
following formula: 90-120° 1,0 1,5
Fmin x KT
WLL =
Zp x g The lifting angle is measured according to the
following figures:
Where
Fmin=The minimum breaking load of the rope in kN
KT = allowed factor for the efficiency of the termi- α
nation α
KL= is the leg factor related to the number of legs α
and the angle to the vertical.
ZP = 5 (Safety Factor)
g=9,81
The calculation yields the max. load on each leg Never excee the sta-
when the lifting angle is 0º, rounded off to the ted max. load at the
nearest hundred kgs. lifting angle involv-
ved. Always check
Max. load for multilegged equipment the rated capacity
If the table is not used, the max. load must be of the equipment
calculated. The result of the above formula, before lifting, not
representing the max. load on a 1-legged sling, after the
shall be multiplied by a factor according to the catastrophe.
following table:
40 41
Choosing equip
Download HSE Docs hseprof.com
ment
Load table for soft
lifting products
WLL in tonnes according to EN 1492
Maximum load in tonnes
Straight lifting Choke hitch basket hitch 45° basket hitch 90° basket hitch
β0-45° α0-90° β45-60° α90-120°
β β
β β
α α
α α
42 43
Download HSE Docs hseprof.com
When lifting General
44 45
Download HSE Docs hseprof.com
When lifting General
46 47
Download HSE Docs hseprof.com
When lifting General
48 49
Download HSE Docs hseprof.com
When lifting General
Treat chain with care. Do not pull Avoid choke-hitching, as loads
it clear from under the load without can tip over.
using spacers. The chain can easily
become damaged and a weakened
chain might break next time you
use it.
50 51
Download HSE Docs hseprof.com
When lifting General
Never point load the hook.
Use an eyebolt with
a larger eye or
connect with
a suitable
shackle.
Never force a
master link
on to a hook.
Use a hook
with a larger
opening.
52 53
Download HSE Docs hseprof.com
When lifting General
54 55
Download HSE Docs hseprof.com
When lifting General
56 57
Download HSE Docs hseprof.com
When lifting General
58 59
Download HSE Docs hseprof.com
When lifting General
60 61
Download HSE Docs hseprof.com
When lifting General
62 63
Download HSE Docs hseprof.com
When lifting General
64 65
Download HSE Docs hseprof.com
When lifting General
The internal angle of a multi-
legged lifting sling should never
exceed 120º, or 60° to the vertical.
Use edge protection if there are
sharp edges. When choke hitching,
reduce the WLL by 20%.
Max 120°
66 67
Download HSE Docs hseprof.com
When lifting General
68 69
Download HSE Docs hseprof.com
When lifting Chain
Never repair chains with bolts. A chain is never stronger than its
Never twist chains. weakest link. Do not repair broken
chains with wires, bolts or by
welding. Replace
the entire
damaged
chain length.
70 71
Download HSE Docs hseprof.com
When lifting Chain
72 73
Download HSE Docs hseprof.com
When lifting Chain
Severe environment
Chain and components in grade 8 and
grade 10 (8+) must not be used in
alkaline (> pH10) or acidic conditions
(< pH6).
Comprehensive and regular examination
must be carried out when used in severe
or corrosive inducing environments, if
using in an uncertain situation, contact
the manufacturer.
76 77
Download HSE Docs hseprof.com When lifting Steel wire rope
Never join wire rope slings by The strength of steel wire rope is
knotting, always use a shackle. reduced by bending. The derating
is related to the diameter of the
bend as follows (d = diameter of
the steel rope):
6d = 100%
5d = 85%
4d = 80%
3d = 70%
2d = 65%
1d = 50%
78 79
Download HSE Docs hseprof.com When lifting Steel wire rope
Do not wind the rope around a
ramshorn hook to prevent
slipping. The
bending will
be too sharp
and cause
damage to
the rope.
80 81
Download HSE Docs hseprof.com When lifting Steel wire rope
Bending like
this will
immediately
destroy the
rope. Use
Use a suitable spacer to prevent lifting slings
the ropes from sliding. Avoid sharp with hooks
bending of the rope. The load can instead.
slip if the lifting points slide. Sharp
bending damages the rope.
82 83
Download HSE Docs hseprof.com When lifting Steel wire rope
A two-legged lifting sling with a Do not expose steel wire rope to excessive
single ferrule fitted like this can heat or cold.
be lethal. The tearing force at
the clamp grows with the lifting Rope with fibre core: max. 100ºC. Rope
with steel core and aluminium ferrule:
angle.
max. 150ºC. Rope with steel core and
steel ferrule/or hand spliced: max.
150ºC = 100%, max. 200ºC = 90%
of WLL, max. 400ºC = 60% of WLL.
According to EN 13414-2
84 85
Download HSE Docs hseprof.com When lifting Steel wire rope
90° max
86 87
Download HSE Docs hseprof.com When lifting Soft equipment
1 23 mm 35 mm
2 32 mm 40 mm
3 35 mm 47 mm
4 38 mm 50 mm
5 42 mm 53 mm
6 46 mm 60 mm
8 50 mm 67 mm
10 56 mm 75 mm
12 58 mm 80 mm
15 70 mm 96 mm
20 78 mm 104 mm Lift vertically and use protective
25 84 mm 112 mm
30 90 mm 120 mm sleeving and/or edge protection
35 96 mm 128 mm
40 102 mm 136 mm to keep the equipment from
50 120 mm 160 mm
directly contacting sharp corners
Note If smaller lug dimensions are used it will and edges.
effect the safety due to that the roundsling
may be damaged.
88 89
Download HSE Docs hseprof.com When lifting Soft equipment
90 91
Download HSE Docs hseprof.com When lifting Soft equipment
92 93
Maintenance
Download HSE Docs hseprof.com
94 95
Maintenance
Download HSE Docs hseprof.com
Inspection
Lifting equipment must be inspected regularly. Turn eyes on the equipment inside out and
Good lighting without shadows is necessary inspect for wear or damage. Inspect webbing
during inspection. one side at a time. When inspecting endless
slings it is recommended to run them around a
Check revolving pin, or similar.
Check / inspect the equipment regularly. Make
sure that repairs are made when needed.
When inspecting soft lifting slings or strops: put
the equipment, stretched to its full length, on a
table.
96 97
Maintenance
Download HSE Docs hseprof.com
Chain
Before inspecting a chain it must be thoroughly The illustration below, showing the distribution
cleaned of dirt and oil. All cleaning methods of strain in a link, can be of guidance for decisions
that do not damage the basic material are on chain wear and damage.
acceptable. No methods that cause hydrogen
embrittlement or overheating are allowed, nor
methods that remove basic material or move
material in a way that might hide cracks or Compressive stress
other visible damage.
Tensile stress
98 99
Maintenance
Download HSE Docs hseprof.com
100 101
Maintenance
Download HSE Docs hseprof.com
Wear Elongation
Inter-link wear, as measured by taking the diameter Overloaded equipment
indicated (d1) and one at right angles, (d2) must be discarded.
is acceptable until the mean of these diameters has Permanent elongation is
been reduced to 90% of the nominal not permitted.
diameter (dn) (see figure) provided.
d1+d2 >0,9d
n
2
d2
d1
A A
A-A
102 103
Maintenance
Download HSE Docs hseprof.com
Effects of
shock loading
A load applied or
relieved quickly (shock)
can damage a steelwire Ropes with kinks, crushing,
rope as the adjacent picture excesive broken wires or
shows. Such a rope must be damaged ferrules must be
discarded. taken out of service.
104 105
Maintenance
Download HSE Docs hseprof.com
106 107
Download HSE Docs hseprof.com Maintenance
Soft lifting Webbing slings and straps
The warp is split as a result of
108 109
Download HSE Docs hseprof.com Maintenance
Keeping a register
Keeping a proper register is important to safe
lifting. The register must describe the equip-
ment and list its identity markings.
110 111
Maintenance
Download HSE Docs hseprof.com
112 113
Download HSE Docs hseprof.com
More information?
Export Sales / Production
Gunnebo Industrier AB
Business Unit Lifting
P.O. Box 44
SE-730 60 Ramnäs
E F F E C T V i m m e r b y, S w e d e n
Dealer
114 115
Download HSE Docs hseprof.com