This document provides a quick installation guide for an Intellian v100NX Ka maritime VSAT antenna system. It outlines 6 key steps: 1) selecting the modem type, 2) setting the target satellite to track, 3) setting the bow offset, 4) installing the above deck unit (ADU), 5) installing the below deck unit (BDU), and 6) initializing and testing the system. Installation requires selecting an obstruction-free location with line of sight to the target satellite, preparing the mast and routing RF cables, and securely mounting the antenna units while following all safety precautions.
This document provides a quick installation guide for an Intellian v100NX Ka maritime VSAT antenna system. It outlines 6 key steps: 1) selecting the modem type, 2) setting the target satellite to track, 3) setting the bow offset, 4) installing the above deck unit (ADU), 5) installing the below deck unit (BDU), and 6) initializing and testing the system. Installation requires selecting an obstruction-free location with line of sight to the target satellite, preparing the mast and routing RF cables, and securely mounting the antenna units while following all safety precautions.
This document provides a quick installation guide for an Intellian v100NX Ka maritime VSAT antenna system. It outlines 6 key steps: 1) selecting the modem type, 2) setting the target satellite to track, 3) setting the bow offset, 4) installing the above deck unit (ADU), 5) installing the below deck unit (BDU), and 6) initializing and testing the system. Installation requires selecting an obstruction-free location with line of sight to the target satellite, preparing the mast and routing RF cables, and securely mounting the antenna units while following all safety precautions.
Select your modem type from the Select Set the target satellite to track. There are two methods for This guide provides basic installation instructions for Intellian v100NX Ka v100NX Ka. The detailed installation and operation user guide 1.05 m Ka-Band Modem drop-down selecting a target satellite. list for the modem can be readily accessible on our website at intelliantech.com. Maritime VSAT Antenna System configuration. The NOTE If you need any assistance, please contact Intellian Technical setting parameters NOTE The following images in this step show when the system is using Support (support@intelliantech.com). related to the modem the Open AMIP modem. interface will be set automatically once the modem type is (Option 1: Using Satellite Controlled by Modem) 2 Planning Installation Quick Installation Guide selected. If you select This method USER SETTING from is generally 2.1 Selection of Installation Site the Select Modem recommended. After Scan the QR code to access the full version of User Guide. drop-down list, the setting the modem The system should be placed in an area on board the vessel settings can be changed manually. connection in the with little to no RF signal blockage. When the antenna is Click the Next button to go to the next step. "Step 3: Modem", transmitting, obstacles in way of the beam path will cause select the Controlled decreases satellite signal strength. The antenna unit should by Modem for the have direct line-of-sight with the desired satellite without 3 ADU (Above Deck Unit) Installation • Step 4: Set Bow Offset Current Satellite. any obstacles in the beam path. Certain minimum distances For setting BOW offset, select one of two satellite tracking Then, the current between the antenna and other on-board devices must also be 3.1 Removing Antenna from Wooden Pallet types and a trackable satellite. satellite and considered during installation. NBD information Four radome brackets secure the antenna to the pallet. To (Option 1: Using Beam Switch Type) will be displayed 2.2 Preparing Mast and RF Cable Installation remove the radome bracket, follow the procedures. automatically. Click 3.1.1 Remove the hex head wrench bolts (2 ea) on each Step 1: Choose the the Next button to go Refer to the Operation and Installation User Guide for detailed information. Check the height and diameter of the mast radome bracket using a wrench. Beam Switch for the to the next step. Tracking Type. recommended by Intellian before installing the antenna. Step 2: Select a NOTE satellite under the Fixing Bolt (2 ea) Beam List, then click (Option 2: Using Manual Setup) NOTE Design the mast considering the recommended thickness of the Apply button. the mast plate (Min. 10.0 mm/ Max. 20.0 mm). If the thickness Wait while the antenna If you did not set the of the mast plate is different from the recommended size, terminal tracks the modem connection, choose right sized bolts for mounting antenna on the mast satellite. select the Manual referring to the Operation and Installation User Guide. Step 3: Make sure the Setup for the Current Lock is on, then click Satellite. Then enter 2.3 Routing RF Cable on Mast the Save Satellite the satellite and NBD button in the Bow information manually Option A. Routing Cable on Outside of Mast Offset menu to save the BOW offset information to ACU. Click the to track a satellite. Click the Apply This method is generally recommended. Next button to go to the next step. button. A.1 Route the cable 3.1.2 Check the condition of lifting strap to make sure the Click the Next button from the gooseneck shackles (2 ea) are tightened. Re-wrap the shackles with the (Option 2: Using Library Type) Sufficient Cable to go to the next step. placed on the deck to existing protection to avoid radome damage. Step 1: Choose the antenna as shown in the Library for the the picture. Shackles (2 ea) Tracking Type. A.2 Maintain a sufficient Step 2: Select a Lifting Strap cable length (at least Cable Brackets satellite under the • Step 7: Report 2 m) when routing the Satellite List, then click the Start NOTE cable on the surface Searching button. NOTE The following image shows when the system is using the Open of the mast. After Gooseneck Wait while the antenna AMIP modem. connecting the cable on Deck terminal tracks the In case of using other modems, the displayed items on the Report to the connector on satellite. may change. the radome, adjust the Step 3: Make sure the length and fix the cable To Below Decks Lock is on, then click The configuration on the cable brackets the Save Satellite report is displayed. using cable ties. button in the Bow You can save the Offset menu to save results to the ACU the BOW offset information to ACU. Click the Next button to go to the 3.1.3 Lift the antenna above the pallet using a crane, and by clicking the Save Option B. Routing Cable Through Inside Mast next step. Report button and maintain a sufficient space (max. 100 mm) between the bottom download the report B.1 Before placing the of antenna and pallet to remove the shipping brackets. file (.json) by clicking radome on the mast, route • Step 5: Blockage the Export button. the cable through the Sufficient Cable WARNING It is important to set Click the View Last gooseneck on the deck WARNING • When lifting the antenna using the lifting straps, up the blockage zones Report button to and the built-in gooseneck Gooseneck make sure to remove the securing radome for Intellian VSAT. The check the recently on the mast for easier on Mast brackets to separate antenna from the pallet. VSAT system can be saved report information including the saved date and time. After placing of the RF Cable complete the steps, click the Finish button. • Be careful when lifting heavy objects. Incorrect programmed with through the inside mast as handling of heavy objects may lead to personal relative azimuth and shown in the picture. injury or significant equipment damage. elevation sectors to Cable Brackets create up to five zones B.2 Maintain a sufficient cable length (at least 2 m) Sufficient Space for the transmission when routing the cable on (Max. 100 mm) mute. The AZ START Gooseneck is the relative azimuth the surface and inside of on Deck angle where the the mast. After connecting blockage starts, and the cable to the connector the AZ END is the on the radome, adjust the To Below Decks relative azimuth angle where the blockage ends (Range: 0 ~ 360). The length and fix the cable on EL is the elevation angle where the blockage is set (Range: 0 ~ 90). the cable brackets using The blockage is activated below the elevation angle. Click the Next button to go to the next step. cable ties.
Doc. No. QG-KU0030-V1.2 Continued on the next page.
4 1 3.1.4 Remove the radome bracket bolt (1 ea) using a wrench, 4 BDU (Below Deck Unit) Installation 5.3 Starting Install Wizard then detach the radome bracket from the radome. M12 Flat Washer The Install Wizard will give you a guide by going through the 3.1.5 Find the supplied Hex Head Wrench Bolts (M6 x 40L), 4.1 Antenna System Configuration steps of setup for the antenna system commissioning. We M12 Spring Washer Spring Washers, and Flat Washers from the ACU box. Apply For the proper operation of the satellite communication system, highly recommend using this wizard to complete the installation Loctite #243 on the bolt, and assemble the bolt and washers M12 x 80L the required components must be connected as shown in the and commissioning of the system. You can exit the wizard at to the radome by turning it clockwise using a wrench. DO NOT Hex. Bolt (BUMAX) figure. Separate purchase of a satellite modem, switch router any time by clicking the Finish button. You can also skip steps reuse the removed bolt and washers. and ship’s gyrocompass may be needed. The basic system by clicking the Next button. Before you start, make sure the 3.1.6 Repeat the procedure to remove all four radome brackets. consists of one VSAT antenna and one ACU. As shown in the basic devices (antenna, modem, etc) are connected to the configuration, connect the cables correctly. ACU properly. After accessing the AptusNX main page, go to Use a torque wrench. the INSTALL WIZ. on the main menu then follow these steps. NOTE 1 2 NOTE Make sure the cable from the mast is aligned with the cable * Refer to the User Guide for Fully Tighten Radome Bolt entry on the bottom of antenna for stable connection. Radome the Dual Antenna System Bracket WARNING Antenna Configuration. • Welcome Page Radome B Bolt WARNING If a bolt does not fit into the mounting hole when installing the A Welcome message is bolt by hand, stop installing and check the bolt size. DO NOT Radome RF Connector displayed. tighten the bolts forcefully. It may cause damage to the inner (Tx, Rx, 48 VDC Power) Bracket Bolt Click the Next button. threads of the mounting holes of antenna. In this case, the Above Decks damage is not covered by the warranty. Below Decks NMEA Input CAUTION 3.5 Connecting RF Cable to Antenna ACU Antenna 2000/0183 BUC I/F LAN 2 CAUTION • Fully tighten the radome bolt. Connect the RF Cable (customer supplied) from the ANTENNA • DO NOT reuse the removed bolt and washers. port of the ACU to the RF connector inside the cable entry of radome. Both side of the connection cable should be Modem Modem LAN 1 terminated using suitable tools. After the connection, securely Rx Tx fix the cable in place using cable ties. 3.2 Placing Antenna Above Mast 100~240 VAC 3.5.1 Remove the M4 x 15L Wrench Bolt by using the wrench The Intellian antenna comes with the lifting straps pre-mounted Switch Router set then open the cable entry cover. (Not supplied) OpenAMIP Tx Rx from the factory. Check the condition of the lifting strap and ensure NOTE the shackle is tightened up. Lift the antenna above the mast using Modem a crane and carefully lower down the antenna toward the mast. NOTE After removing the M4 x 15L Wrench Bolt from the cover of • Step 1: GPS cable entry, Keep it in a safe place for the next step. When (Not supplied) BUC Maintain sufficient space (at least 150 mm) between the bottom of Ship's Gyrocompass I/O closing the cover of cable entry, this bolt must be used. 100~240 VAC (Not supplied) Set the GPS position radome and the mast for cabling work. of the vessel for the WARNING 3.5.2 Terminate N(M) connector on the end of the RF Cable. satellite searching. Intellian recommends using a genuine cable connector and Check the GPS WARNING When moving the antenna, it may sway by windy. Be careful status connected to when handling the antenna. tools. Refer to the cable termination instructions provided by the manufacturer to terminate the N connector. the antenna system. NOTE 3.5.3 Connect the terminated RF cable to the connector as 5 Operating Install Wizard The colored indicator next to the title shows NOTE Position the antenna with the BOW direction parallel to the the following figure. Ensure the cable is firmly fastened to the the GPS status. center line of the ship. connector. Fasten the cable with Make sure the GPS 5.1 Turning On System cable ties using the cable mount indicator is Blue Press the POWER button on the front panel of the Antenna (blinking). or cable clamp along the routing Cable Tie path. Bracket Control Unit (ACU), then wait a few minutes for system startup. • Blue (blinking): The 3.3 Inserting Waterproof Foam Once the antenna finds the satellite, the POWER indicator will system received a 3.5.4 After completing cable correct GPS signal. The supplied waterproof foam must be turn Green. Adhesive connection, put the cover in the • Red: The GPS signal is abnormal, or the received value is incorrect inserted to prevent water penetration into Tape right place and tighten the M4 x (Error). the radome before mounting the radome 5.2 Accessing AptusNX Cable Hole 15L Wrench Bolt by using the wrench set. • Black: The system has not received any GPS signal. You can enter on the mast. Make sure the waterproof the GPS value manually to set the GPS position. Click the Next foam is positioned where the following (X-shaped) The network is automatically configured by DHCP with no 3.6 Switching on Power Box additional PC IP configuration. button to go to the next step. picture shows. * For details about the installation procedure, refer to the User Guide. Access the ADU modules inside the radome to check that the 5.2.1 Connect an Ethernet cable from the Management LAN power switch is on through the radome hatch. Make sure that port on the front panel of the ACU to a LAN port of PC. there is sufficient free space underneath the ADU to open the 5.2.2 The network connection is established automatically. radome hatch. 5.2.3 Use the following IP address to access Intellian AptusNX • Step 2: Heading 3.6.1 Bring the radome page. Cable door key from the ACU box. Set the ship’s heading • IP Address: 192.168.2.1 (Default) device. Access Hole Open the radome hatch by turning the fixed bolts 5.2.4 Log into the AptusNX by entering User ID and Password. The colored indicator Position of next to the title shows counterclockwise by using Waterproof • User ID: intellian (Default) the heading device the radome door key. connection status. Foam • Password: 12345678 (Default) 3.6.2 The power box • Blue: Ship’s heading switch was turned on device is connected. 3.4 Mounting Antenna on Mast and shipped from the • Black: Ship’s factory. Check the power heading device is not Bring M12 x 80L Hex Bolt sets (4 ea) for antenna-mast box inside the radome is connected. assembly from the ACU box. Place the antenna on the mast switch on. If not, switch Management LAN Port If a gyrocompass is and align the mounting holes of the antenna with those of connected, choose on the power box. the device type from the mast. Before assembling bolts, apply Loctite #263 to the PC (Not supplied) bolt threads to ensure the bolts are fastened firmly. Insert the the Current Device drop-down list. Then, click the Apply button. 3.6.3 Put the radome hatch in the right If no gyrocompass is connected, choose NONE for the Current bolts and washers from under the mast into the radome, and place. Close the radome hatch by turning Door Key Provided Device from the drop-down list. Then, click the Apply button. lightly tighten them by hand into the built-in nuts on the bottom the fixed bolts clockwise by using the NOTE: Skip "Step 4: Set Bow Offset" if no gyrocompass is of radome. Install 4 bolts in a criss-cross sequence. After radome door key. connected. installing all 4 bolt sets, fully tighten the bolts using a torque Click the Next button to go to the next step. wrench. After mounting the antenna on the mast, remove the NOTE lifting strap. NOTE After using the door key, store it in a safe place for future use. Continued on the next page. 2 3