Professional Documents
Culture Documents
303-07A Engine Ignition - 1.5L EcoBoost
303-07A Engine Ignition - 1.5L EcoBoost
o
.c
gn
ia
rd
ca
303-07A Engine Ignition - 1.5L EcoBoost (132kW/180PS) – I3 2020 Escape
SpeciDications PdoceTrde deuision Tatev 08/7/201:
Specifications
Firing order
Item Value
Firing order 1-2-3
Spark Plug
Item Value
m
Spark plug 12405
Spark plug gap 0.8 mm
co
n.
i ag
rd
ca
m
Description and Operation
o
.c
gn
ia
rd
ca
303-07A Engine Ignition - 1.5L EcoBoost (132kW/180PS) – I3 2020 Escape
Description and Operation Procedure revision date: 08/7/2019
m
1
Item
Ignition coil-on-plug(s)
Description
co
n.
2 Saprk plug(s)
i ag
rd
ca
m
Diagnosis and Testing
o
.c
gn
ia
rd
ca
303-07A Engine Ignition - 1.5L EcoBoost (132kW/180PS) – I3 2020 Escape
Diagnosis and Testing Procedure revision date: 05/12/2017
Engine Ignition
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. For information about these,
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
For a DTC,
REFER to: Electronic Engine Controls (303-14C Electronic Engine Controls - 2.5L Duratec – Hybrid (121kW/164PS) (BG), Diagnosis and
Testing).
For driveability symptoms without a DTC, Refer to Powertrain Control/Emissions Diagnosis (PC/ED) manual. See Section 3, Symptom Charts.
m
co
n.
i ag
rd
ca
m
Removal and Installation
o
.c
gn
ia
rd
ca
303-07A Engine Ignition - 1.5L EcoBoost (132kW/180PS) – I3 2020 Escape
Removal and Installation Procedure revision date: 11/7/2019
Ignition Coil-On-Plug
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Disconnect the battery.
Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. NOTICE: Do not pull the engine appearance cover forward or sideways to remove. Failure to press straight upward on the underside of the cover at the
attachment points may result in damage to the cover or engine components.
NOTE: Lubricating the grommets with silicone grease will aid in the installation of the engine appearance cover, and any future removal and installation of
the cover.
Remove the engine appearance cover.
m
co
n.
ag
NOTE: When removing the ignition coil-on-plugs, a slight twisting motion will break the seal and ease removal.
Remove the bolts and the ignition coil-on-plugs.
Torque: 89 lb.in (10 Nm)
i
rd
ca
m
co
n.
6. Inspect the ignition coil-on-plug assembly for cracks, rips or tears. Replace any damaged coil-on-plug assemblies.
i ag
rd
ca
Installation
1. To install, reverse the removal procedure.
ca
rd
i ag
n.
co
m
303-07A Engine Ignition - 1.5L EcoBoost (132kW/180PS) – I3 2020 Escape
Removal and Installation Procedure revision date: 09/19/2019
Spark Plugs
Special Tool(s) / General Equipment
303-1625
Socket, Spark Plug
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Refer to: Ignition Coil-On-Plug (303-07A Engine Ignition - 1.5L EcoBoost (132kW/180PS) – I3, Removal and Installation).
2. Use compressed air to remove any foreign material in the spark plug well before removing the spark plugs.
3. Use Suggested Tool: 303-1625 Socket, Spark Plug. Tool shown or a commercially available equivalent can be used.
Torque: 159 lb.in (18 Nm)
m
co
n.
i ag
rd
Installation
1. To install, reverse the removal procedure..
ca