Professional Documents
Culture Documents
15 Nitoseal mb99 1
15 Nitoseal mb99 1
Used for sealing horizontal movement and construction Nitoseal MBA1 (formerly known as Pliastic A1) is for
joints in concrete pavements and floor slabs. higher movement joints in locations where the ambient
o o
temperature is between –20 C and 40 C, where slump
Typical areas include;
resistance is important at higher ambient temperatures or
Pavements, roads and traffic surfaces where joint spacings exceed 12 metres e.g. road
Nitoseal MB77
Water retaining structures including reservoir floors
and roofs, swimming pool substructures and irrigation Nitoseal MB77 (formerly known as Pliastic 77) is a hard
canal floors. grade for sealing low movement joints in factory floors and
Advantages areas where joints are closely spaced and resistance to
grit and traffic is of prime importance.
An economical sealant for horizontal and inclined
Nitoseal MB99
joints up to 1 in 20
Resists dirt and ingress of grit associated with Nitoseal MB99 (formerly known as Pliastic 99) is similar in
Page 445
Fosroc® Nitoseal MB99
(Formerly known as Fosroc® Pliastic)
Properties Priming
Application Porous surfaces such as concrete, stone and brick paving,
o
Temperature Over 5 C should be primed with Fosroc Primer 3. Brush apply
Chemical resistance Dilute acids resistant primer and allow to become touch dry before sealing,
To occasional spillage Dilute alkalis resistant normally 1 to 4 hours.
Petroleum
Non-porous surfaces do not normally require priming.
Solvents not resistant
Ferrous metals should be treated with an anti-corrosion
Minerals oils not resistant
primer, such as Fosroc Galvafroid.
Vegetable oils not resistant
Greases not resistant Heating
Drinking water : Nitoseal MB99 is not soluble in
The use of a heating vessel with oil jacket and fitted with
water and therefore imparts no
stirrer and the thermometer is essential.
taint to it.
Movement Accommodation Factor: Cut the compound into small pieces, melt a few pieces
Total joint range, butt joints: then gradually add more pieces to the molten material
Nitoseal MBA1 and Nitoseal MBA2: 12% stirring continuously. Heat until the compound reaches it’s
Where applicable, care must be taken to ensure that the Equipment should be emptied immediately after use.
compressible joint filler, such as Flexcell, will provide Compound that heated and allowed to cool completely
adequate support for the Nitoseal MB99 compound. must be scrapped.
Estimating Precautions
Packaging
Nitoseal MB (All Grades)
Nitoseal MB (all grades) : 20 kg
No health hazards associated with normal use, however,
Fosroc Primer 3 : 1 litres
avoid breathing fumes and do not overheat.
Coverage
Fosroc Primer 3
Nitoseal MB (all grades)
no. of kgs. Per meter : depth(mm) x width(mm) Highly flammable liquid. Keep away from sources of ignition
1000 – No Smoking.
Fosroc Primer 3 : 1 litre for every 50 kgs Harmful, if inhalation and contact with skin. Avoid contact
of Nitoseal MB or 12 – with skin and eyes and inhalation of the vapours. Wear
2
15 m /litre suitable protective clothing, gloves and eye/face protection.
Limitations Use only in well ventilated areas.
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control
over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
Fosroc Sdn. Bhd. not in accordance with any advice, specification, recommendation of information given by it.
Branch Office:
+60 4 2287 464 +60 4 2292 661
29, Jalan Zainal Abidin,
10400 Penang, Malaysia.