Professional Documents
Culture Documents
LH70 InitialSetupManual Ver1 E
LH70 InitialSetupManual Ver1 E
11) CS&S
LH70 LH70
Table of contents
Contents Page
Preparations before making the initial settings (checking conditions of use) 2 to 3
How to set up Detailed Settings (continued from Basic Settings) STEP 4~5 7
1/12
LH70 initial Setup Manual
Preparations before making the initial setting (1/2)
By confirming the conditions of use in advance, the setting operation can be performed easily.
Let's start with the basic settings.
Type The function of LH70-3 (3 axes) can GENERAL: Milling machine function
(function selection) be selected according to the type of LATHE: Lathe function
machine used.
Only GENERAL (milling machine
function) can be selected for LH7-1 / 2
LH70-3 only (1 axis, 2 axes).
Addition display Selection of addition axis, addition 2: No addition, count value of the 2nd axis
conditions, etc. 3: No addition, count value on the 3rd axis
2 Add 3: Count value of 2nd axis + 3rd axis
If you select LATHE (lathe function) in 2 Add -3: Count value of 2nd axis-3rd axis
Can be selected when
"Lathe" (lathe the type selection, this item will appear. -2 Add 3: 3rd axis-2nd axis count value
function) is selected -2Add-3: -2nd axis -3rd axis count value
Destination country Please select the region to be used. Std: General Area
(Displayable units)
US: U.S.A.
JPN: Japan
Measuring unit Set the resolution output from the Length: 0.05 to 100μm
resolution measurement unit to be used for each *See Tables 1, 2 and 3
axis. or
The resolutions that can be selected Angle: 1 second to 1 degree
are length and angle.
Expanded selections increase the *Angular resolution (1sec to 1 degree) when
number of options. using a rotary scale
2/12
LH70 initial Setup Manual
Preparations before making the initial setting (2/2)
Check the usage conditions for Detailed Settings.
(Since the setting conditions can be changed later, use the default values to skip items for which
the conditions have not been confirmed)
Display resolution Sets the resolution to be displayed for each Length: 0.05 to 100μm
and polarity axis. A value lower than the input resolution
cannot be set. Selects the value for each or
axis, including the polarity (+/-). Angle: 1 second to 1 degree
The default value is set by the basic setting.
Display switching Upper axis Each display axis can be selected for the Input axis:
length measurement unit input axis.
IN-1: 1st input axis
Middle axis
IN-2: 2nd input axis
IN-3: 3rd input axis
Lower axis
IN - -: No display
Axis label switching Upper:X Display axis label selection Upper axis: "X" or "Z"
Middle:Y
Can be used with LH70-1 and LH70-2. Middle axis: "Y" or "Z"
Flicker control Flickering of the smallest displayed digit OFF: Function stop
can be suppressed. Set the level of flicker
suppression. 1: Weak
2: Strong
Sleep The display turns off when there is no OFF: Do not put to sleep
movement of the length measurement unit
or key operation for a certain period of time 1: 1 minute later
while the power is on. 5: 5 minutes later
It will return when the length measurement
unit is moved or the Key operation is 10:10 minutes later
performed again. 30:30 minutes later
60: 60 minutes later
3/12
LH70 initial Setup Manual
How to set up Basic Settings (1/3)
Note:
Configure the basic settings.
Step 1 If you change the basic settings,
Detailed Settings will be reset to the factory defaults.
Choose one of the following methods of operation.
When the power is turned on for the first When you want to change the basic
time after shipment from the factory settings
AC adapter is energized.
Turn on key, the LED light changes from
Connect the AC adapter and turn the primary power "on".
"blinking" to “off" and then press
and hold key for 3 seconds.
SET-UP key
Enter key
After about 2 seconds
AC primary power source
Pressing key changes the basic setting mode in the order in which it is set.
COUNTRY (Destination)
Note: When "Lathe" (lathe function) is selected on Symbol Destination Unit
the LH70-3 (3-axis input), be sure to connect a scale
with high resolution to the length measuring unit STD General area
input axis 2 to display the addition. US U.S.A.
JPN Japan
4/12
LH70 initial Setup Manual
How to set up Basic Settings (2/3)
Enter the settings confirmed in "Preparations before making initial settings (1/2)".
Step 2 Repeat steps (1), (2), and (3) to make the basic settings.
default default
JAPAN
20μm
10 seconds
input 3- input 2
25μm
1 second
- (input 2 + input 3)
50μm
10μm 100μm
5μm 1 degree
Display method:
- For each setting item, the current setting
contents are displayed after about 1 second. If
1μm
there is no change in the contents, move to the
next section with key.
5/12
LH70 initial Setup Manual
How to set up Basic Settings (3/3)
Once you have completed the basic settings, exit this mode and move to
Step 3 Detailed Setting mode.
④ Press key.
Reset key
Φ lamp
(two times display)
Setup key
Edit key
Enter key
6/12
LH70 initial Setup Manual
How to set up Detailed Settings (1/1) (continued from Basic Settings)
*If you have already completed the basic settings and want to reconfigure only
Step 4 Make the detailed settings. the advanced settings, you can do the same.
Basic Settings
・ Display resolution is set by pressing key on each axis.
Press the setup key
in the normal count display state. ・ A value smaller than the input resolution cannot be selected.
・ Polarity changes with key
・ To display the diameter (double display), turn on on the
display axis.
Display resolution
(Note 1) (Note 2)
Length display Angle display Extended resolution
Diameter display
Note 1: Selection of a value smaller than the basic setting Press the edit key
length measurement unit resolution is not displayed.
Note 2: The angle display can be selected when the angle
resolution is selected in the basic settings.
INPUT CHANGE Selection of each display axis and measurement unit input axis
(display switching) Upper: input 1 Set by select axis key
Display example
Middle :input 2
LH70-3
Lower: input 3
Detailed Settings
Note The axis labels for the 1st and LH70-1, LH70-2
LABEL 2nd axes can be selected from
(axis label switching) "X", "Y", and "Z".
Note:
Can be used with LH70-1 and LH70-2.
Liner Error
(Linear compensation)
Normal ~
Extended res. ~
7/12
LH70 initial Setup Manual
FLICKER Flickering of the smallest digits can be suppressed in two stages
(flicker control) default
Detailed Settings
1 min. 10 min. 1h
Step 5 6. When the Detailed Settings are complete, switch to the normal display.
Press key.
8/12
LH70 initial Setup Manual
Factory Default (All Clear)
To set the factory settings (all clear), perform the following operations.
Make preparation such as taking notes in advance for necessary items.
Also, do not perform any operation other than the explanation.
Caution: If you do this, all settings will be the factory default settings.
Setup key
Lights up
”RUN”
DC input
1. Hold down key and key at the same time to start the power supply.
Connect the AC adapter to the DC-IN input on the back of the counter and
turn on the primary power supply.
START → → →
→ → → completion
Alarm indication
Display Status Display Status
(Blinking)
Storage data error
Measurement unit not
connected
Overflow
Power failure
Note: When using an adapter connection (SZ**), no speed override indication is shown, but rather an error message.
10/12
LH70 initial Setup Manual
Appendix 2-1 Adapter connection (Length scale)
Cable (300mm)
Screws
Head-amp
Cable (300mm)
Screws
Screws
connector
SZ70-1
* HA13A, 15A, 23A and 25A are used as head amps Screws
SZ05-T01
Head-amp
Connector
Screws
11/12
LH70 initial Setup Manual
Appendix 2-2 Adapter connection (Digital gauge)
Screws
DK series CE29-**
DZ51
Screw
SZ70-1 connector
SZ05-T01
Head-amp
Connector
Screws
Use screws to secure it in place.
Head-amp
SZ70-1 Connector
12/12
LH70 initial Setup Manual